Operator's Manual. Please read these instructions carefully and make sure you understand them before using the machine.

Transcription

1 Operator's Manual Please read these instructions carefully and make sure you understand them before using the machine.

2

3 TABLE OF CONTENTS Operator s manual for FR 2111, FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Introduction... 2 Driving and transport on public roads... 2 Towing... 2 Use... 2 Serial number... 3 Explanation of symbols... 4 Safety instructions... 5 General use... 5 Driving on slopes... 7 Children... 8 Maintenance... 8 Transport Presentation Placement of controls Throttle and Choke controls FR 2111,FR 2111 M Clutch pedal FR 2111, FR 2111 M Brake pedal/parking brake FR 2111,FR 2111 M.. 12 Throttle and Choke controls FR 2113 MA, FR 2115 MA, FR 2116 MA Throttle contro FR 2116 MA Choke lever FR 2116 MA Accelerator FR 2113 MA, FR 2115MA, FR 2116 MA, FR 2116 MA Parking brake FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA Cutting deck Lifting lever for the cutting deck Lever to adjust the cutting height Seat Refuelling Driving Before starting Starting the engine To start an engine with a weak battery Driving the Rider Cutting tips Starting on slopes, manual gearbox Stopping the engine Maintenance Maintenance schedule Cleaning Dismantling the Rider covers Inspecting the silencer Checking and adjusting the steering wires Checking the brake FR 2111, FR 2111 M Adjusting the brake FR 2111, FR 2111 M Checking and adjusting the parking brake FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA Adjusting the throttle cable, FR 2111, FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA Checking and adjustment of the throttle wire, FR 2116 MA Checking and adjusting the choke wire, FR 2116 MA Replacing the fuel filter Replacing the air filter Checking the fuel pump s air filter Checking the acid level in the battery Ignition system Checking the safety system FR 2111, FR 2111 M.. 35 Checking the safety system FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA Main fuse Kontroll av däckens lufttryck Checking the tyres air pressure Checking the engine s cooling air intake Checking and adjusting the Cutting deck s ground pressure FR 2113 MA, FR 2115 MA, FR 2116MA, FR 2116 MA Checking the parallelism of the Cutting deck. 38 Adjusting the parallelism of the Cutting deck FR Removing the mulching plug, Combi 103, Removing the mulching plug The Cutting deck s service position Inspecting the blades Lubrication Check the engine s oil level Changing the oil Changing the oil filter, FR 2116 MA Checking the oil level in the transmission FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA Lubricating the belt adjuster General lubrication Lubricating the front wheel bearings Trouble shooting chart Storage Winter storage Cover Service Technical data EU declaration of conformity Service schedule Service journal IMPORTANT INFORMATION Read carefully through the Operator s manual so that you know how to use and maintain the Rider before you use it. For service measures other than those described in this manual, please contact an authorised dealer that provides parts and service. English 1

4 Congratulations INTRODUCTION Thank you for purchasing a Front Rider. Front Riders have been designed according to a unique concept with a front mounted Cutting deck and patented rear wheel steering. The machine is built to give maximum efficiency even in small and confined areas. Collected controls and a hydrostatic transmission controlled by pedals(some models) also contribute to the machine s performance. This operator s manual is a valuable document. Following the instructions (use, service, maintenance, etc.) can considerably increase the life span of your machine and even increase its resale value. When you sell your machine, make sure to give the operator s manual to the new owner. Driving and transport on public roads Check applicable road traffic regulations before driving and transport on public roads. You should always use approved fasteners during transport and ensure the machine is secured correctly. Towing Your machine is equipped with a hydrostatic transmission and, if necessary, you should only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission. Use This machine has been designed solely to mow grass on lawns and other open and level ground surfaces without obstacles such as stones, stumps and the like. The machine can also be used for other tasks when equipped with special accessories supplied by the manufacturer and for which the operator s manual has been supplied in connection with delivery. All other types of use are incorrect. The manufacturer s instructions with regard to driving, maintenance and repair must be followed precisely. The machine may only be operated, maintained and repaired by persons that are fully conversant with the machine s special characteristics and safety instructions. Accident prevention regulations, other general safety regulations, occupational safety rules and traffic regulations must be observed. Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or damage to property. 2 English

5 Good service INTRODUCTION Jonsered s products are sold all over the world and only in specialised retail trade with complete service. This ensures that you as a customer receive only the best support and service. Before the machine is delivered it undergoes inspection and is adjusted by your dealer. When you need spare parts or support in questions about service, warranty issues, etc., please consult the following professional: This operator s manual belongs to machine with serial number: Engine Transmission Serial number The serial number can be found on the printed plate attached to the front, left-hand side under the seat. Stated on the plate, from the top are: The machine s type designation. The manufacturer s type number. The machine s serial number. Please state the type designation and serial number when ordering spare parts. The engine number is punched on a plate that is riveted to the fan cover. The plate states: Model. Type. Code. Please state these when ordering spare parts. The transmission s serial number on hydrostat machines is stated on the barcode decal located on the front of the housing on the left-hand drive shaft: Type designation is stated above the barcode and starts with the letter K. The serial number is stated above the barcode and has the prefix s/n. The manufacturer s type number is stated under the barcode and has the prefix p/n. Please state the type designation and serial number when ordering spare parts. English 3

6 EXPLANATION OF SYMBOLS These symbols can be found on the Rider and in the operator s manual. Study them carefully so you understand their significance. Read the operator s manual. R N Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil level Cutting height Reversing Forward Ignition Hydrostatic free wheeling Use hearing protection Clutch in Clutch out Parking brake Brake Clutch Warning Noise emissions to surroundings in accordance with the European Union s directive. The machine s emissions are set out in the chapter TECHNICAL DATA and on the decal. Warning! Rotating blades Warning! Risk of the Rider overturning Never drive directly across a slope CE conformity marking Never use the Rider if persons, especially children or pets, are in the immediate vicinity Never carry passengers on the Rider or on its tools Do not insert your hands or feet under the cover when the engine is running Drive very slowly without the Cutting deck Accelerator pedal forward Starting instruction Read the operator s manual Check the engine oil level Check the oil level in the hydrostat Lift up the Cutting deck Put the gear shift lever/hydrostat pedals in the neutral position Brake Use the choke if the engine is cold Starting the engine Disengage the parking brake before driving Neutral position Accelerator pedal reversing Switch off the engine and remove the ignition cable before carrying out repairs or maintenance 4 English

7 SAFETY INSTRUCTIONS Safety instructions These instructions are for your safety. Read them carefully. WARNING! The inserted symbol means that important safety instructions need to be observed. It applies to your safety. General use Read all the instructions in this operator s manual and on the machine before you start it. Ensure you understand them and then observe them. Learn how to use the machine and its controls safely and learn to how to stop quickly. Also learn to recognize the safety decals. Only allow the machine to be used by adults who are familiar with its use. Make sure nobody else is in the vicinity of the machine when you start the engine, engage the drive or drive off. Make sure animals and people maintain a safe distance from the machine. Stop the machine if any one enters the working area. Clear the area of objects such as stones, toys, wires, etc. that may become caught in the blades and be thrown out. Look out for the ejector and do not direct it towards anyone. Stop the engine and prevent the engine from being started until you have cleaned the cuttin deck or outlet channel. Remember the operator is responsible for danger or accidents. Never carry passengers. The machine is only intended to be used by one person. Always look downwards and backwards before and while reversing. Keep watch for both large and small obstacles. Slow before cornering. Switch off the blades when you are not Cutting Read the operator s manual before starting the machine. Clear the area of objects before Cutting Never carry passengers WARNING! This machine can sever hands and feet as well as throw objects. Failure to observe the safety instructions can result in serious injuries. English 5

8 SAFETY INSTRUCTIONS Take care when rounding a fixed object, so that the blades do not hit it. Never run the machine over foreign objects. Only use the machine in daylight or in other well-lit conditions. Keep the machine at a safe distance from holes or other irregularities in the ground. Pay attention to other possible risks. Never use the machine if you are tired, if you have consumed alcohol, or if you are taking other drugs or medication that can affect your vision, judgment or co-ordination. Keep an eye on the traffic when working close to a road or when crossing it. Never leave the machine unsupervised with the engine running. Always stop the blades, apply the parking brake, stop the engine and remove the keys before leaving the machine. Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may regulate the age of the user. WARNING! Engine exhaust, some of its constituents and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive impairment. The engine emits carbon monoxide, which is a colourless, poisonous gas. Do not use the machine in enclosed spaces. Keep children away from the area to be mowed WARNING! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment. Make sure that you have first aid equipment close at hand when using the machine. Never use the machine when barefoot. Always wear protective shoes or protective boots, preferably with steel toes. Wear approved protective glasses or full-face visor during assembly and when operating. Never wear loose fitting clothes that can catch in moving parts. Use ear protectors to eliminate the risk for impairment of hearing. Personal protective equipment English

9 Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest; this can result in serious injury or death. All slopes demand extra care. If you cannot reverse up a slope or if you feel unsure, do not mow it. SAFETY INSTRUCTIONS Proceed as follows: Remove obstacles such as stones, branches, etc. Mow upwards and downwards, not sideways. Do not use the machine on ground that slopes more than 15. Avoid starting or stopping on a slope. If the tyres start to slip, stop the blades and drive slowly down the slope. Always drive smoothly and slowly on slopes. Do not make any sudden changes in speed or direction. Avoid unnecessary turns on slopes, if necessary, turn slowly and gradually downwards if possible. Watch out for and avoid driving over furrows, holes and bumps. It is easier for the machine to overturn on uneven ground. Tall grass can hide obstacles. Drive slowly. Use small movements of the steering wheel. Select a low gear, so you do not need to stop to change gear. Engine braking on the machine is also better in a low gear. Take extra care if any attachments are fitted that can change the stability of the machine. Do not mow too close to edges, ditches or banks. The machine can suddenly overturn if one wheel comes over the edge of a steep slope or a ditch, or if an edge gives way. Do not mow wet grass. It is slippery, and tyres can lose their grip so that the machine skids. Do not try to stabilize the machine by putting your foot on the ground. When cleaning the chassis the machine must never be driven close to an edge or ditch. Follow the manufacturer s recommendations regarding wheel weights or counterbalance weights to increase stability. Be especially careful when driving on slopes Mow upwards and downwards on slopes, not sideways English 7

10 SAFETY INSTRUCTIONS Children Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Children are often attracted to the machine and Cutting. Never assume that children will remain where you last saw them. Keep children away from the area to be mowed and under close supervision by another adult. Keep an eye out and shut off the machine if children enter the work area. Before and during reversing procedures, look behind you and down for small children. Never allow children to ride along. They can fall off and seriously injure themselves or be in the way for safe manoeuvring of the machine. Never allow children to operate the machine. Be particularly careful near corners, bushes, trees or other objects that block your view. Never allow children to operate the machine Maintenance Stop the engine. Prevent starting by removing the ignition cable from the spark plug or remove the ignition key before making any adjustments or carrying out maintenance. Never fill the fuel tank indoors. Petrol and petrol fumes are poisonous and extremely flammable. Be especially careful when handling petrol, as carelessness can result in personal injury or fire. Only store fuel in containers approved for the purpose. Never remove the fuel cap and fill the petrol tank while the engine is running. Allow the engine to cool before refuelling. Do not smoke. Do not fill petrol in the vicinity of sparks or naked flames. Observe the risk of environmental damage when handling oil, fuel and the battery. Remember to follow local regulations concerning waste handling. Electric shocks can result in injury. Do not touch the ignition lead when the engine is running. Do not test the ignition system with your fingers. Never fill the fuel tank indoors English

11 SAFETY INSTRUCTIONS If leaks arise in the fuel system, the engine must not be started until the problem has been resolved. Store the machine and fuel in such a way that there is no risk that leaking fuel or fumes can cause any damage. Check the fuel level before each use and leave space for the fuel to expand, because the heat from the engine and the sun may otherwise cause the fuel to expand and overflow. Avoid overfilling. If you spill petrol on the machine, wipe up the spill and wait until it has evaporated before starting the engine. If you spill petrol on your clothing, change your clothing. Allow the machine to cool before performing any actions in the engine compartment. Be especially careful when handling battery acid. Acid on the skin can cause serious corrosive injuries. In the event of spillage on the skin wash immediately with water. Acid in the eyes can cause blindness, contact a doctor immediately. Take care with battery maintenance. Explosive gases form in the battery. Never perform maintenance on the battery while smoking or in the vicinity of open flames or sparks. This can cause the battery to explode and cause serious injuries. Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition. Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven if protective plates, protective covers, safety switches or other protective devices are not fitted or are defective. Do not change the setting of governors and avoid running the engine at excessively high revs. If you run too fast, you risk damaging the machine components. Observe the risk of injury caused by moving or hot parts if the engine is started with the engine cover opened or the protective covers removed. WARNING! The engine, and components of the exhaust and hydraulic systems become extremely hot during operation. Risk for burns with contact. WARNING! The battery contains lead and lead pollutants, chemicals that are considered to cause cancer, birth defects or other reproductive impairment. Wash your hands after touching the battery. Do not smoke when carrying out maintenance English 9

12 SAFETY INSTRUCTIONS Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas. Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. Never make adjustments with the engine running. The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. The blades are sharp and can cause cuts. Wrap the blades or wear protective gloves when handling them. Check regularly that the parking brake works. Adjust and maintain as required. The mulching unit should only be used where better quality Cutting is required and in known areas. Reduce the risk of fire by removing grass, leaves and other debris that may have fastened on the machine. Allow the machine to cool before putting it in storage. Never run the machine in an enclosed area Transport The machine is heavy and can cause serious crush injuries. Be especially careful when it is loaded in or out of a car or on and off of a trailer. Use an approved trailer to transport the machine. Activate the parking brake and secure the machine using approved fasteners, such as tension belts, chains or ropes when transporting. Check and observe local road traffic regulations before transporting or driving the machine on roads Regularly clean grass, leaves and other debris from the machine. IMPORTANT INFORMATION The parking brake is not sufficient to lock the machine during transport. Ensure you secure the machine firmly to the transporting vehicle. Reverse the machine on to the transporting vehicle to prevent it from overturning. 10 English

13 PRESENTATION Presentation Congratulations on your choice of an exceptionally high quality product. Six models equipped with engines from Briggs & Stratton are described in this operator s manual. FR 2111, FR 2111 M has an inline type gearbox with 5 forward gears and reverse. On FR 2113 MA, FR 2115 MA, FR 2116 MA and FR 2116 MA2 transmission is by means of a variable speed hydrostatic gearbox. FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 has combi unit Placement of controls 1. Ignition key 2. Throttle/Choke control 3. Choke control, FR 2116 MA2 4. Adjustment of the cutting height 5. Lifting lever, cutting deck 6. Accelerator for reversing, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 7. Accelerator for driving forwards, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Parking brake, FR 2111, FR 2111 M Parking brake, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Clutch pedal, FR 2111, FR 2111 M 9. Lock button for the parking brake left-hand side for FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 right-hand side for FR 2111, FR 2111 M 10. Seat adjustment 11. Fuel cap 12. Main lock (under seat) 13. Lever for disengaging the drive, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 14. Gear shift lever, FR 2111, FR 2111 M English 11

14 Throttle and Choke controls PRESENTATION FR 2111, FR 2111 M The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold Clutch pedal The clutch pedal disengages the engine and stops propulsion. The blade drive is not affected by the clutch pedal Brake pedal / Parking brake The brake pedal activates a disc brake that is located on the gearbox and stops the drive gear. The clutch pedal should also be pressed down when braking to achieve the best braking effect. The brake pedal also acts as a parking brake if the lock button is pressed in when the pedal is pressed down English

15 PRESENTATION FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Throttle and Choke controls The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold Throttle control, FR 2116 MA2 The throttle control regulates the engine speed, and thereby also the rotation speed of the blades. To increase or reduce the engine speed the control is moved forwards or backwards. Avoid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs. FR 2116 MA Choke lever, FR 2116 MA2 The choke lever is used for cold starting and to give the engine a richer fuel mixture. For cold starting the lever is moved backwards to its end position. FR 2116 MA English 13

16 PRESENTATION FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Accelerator The speed of the machine is variably controlled using two pedals. Pedal (1) is used to travel forwards and pedal (2) to reverse. WARNING! Make sure that no branches can interfere with the pedals when Cutting under bushes. Risk for unintentional manoeuvring Parking brake The parking brake is activated as follows: 1. Press down the parking brake pedal (1). 2. Press in the lock button (2) on the steering column. 3. Release the parking brake pedal while keeping the button pressed in. The parking brake lock is automatically disengaged when the parking brake pedal is pressed down H 14 English

17 Cutting deck FR 2111 have a triple blade cutting deck with rear ejection, i.e. the clippings are thrown out behind the cutting deck. PRESENTATION FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 has a triple blade Combi unit, which can be set to either a mulching function or rear ejection by removing a mulching plug. Lifting lever for the cutting deck The lifting lever is used to put the cutting deck in either the transport or Cutting positions. If the lever is pulled backwards the deck is raised and the blades automatically stop rotating (transport position). If the lock button is pressed in and the lever is moved forwards the deck will be lowered and the blades will automatically start to rotate (cutting position). The lever can also be used to temporarily adjust the cutting height, for example, with a small mound in the lawn. Lifting the cutting deck (transport position) Lowering the cutting deck (cutting position) English 15

18 Lever to adjust the cutting height Using the lever the cutting height can be adjusted in 9 different positions. Deck with rear ejection, mm Combi unit, (1 3/4" - 3 3/4") PRESENTATION Seat The seat has a hinged mounting on the front edge and can be folded forwards. The seat can also be adjusted lengthways. Loosen the handles under the seat and adjust it forwards or backwards to the desired position. Secure the adjustment using the handles Refuelling The engine should be run on a minimum of 85-octane grade unleaded petrol (not mixed with oil). It can be beneficial to use environmentally adapted alkylate petrol. Do not use petrol that contains methanol. Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1"). WARNING! Petrol is highly flammable. Observe caution and fill the tank outdoors (see the safety instructions) English

19 DRIVING IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage. Before starting Read the safety instructions and information concerning the placement of controls and functions before starting. Carry out daily maintenance before starting (see the maintenance schedule). Adjust the seat to the desired position Starting the engine 1. Lift up the cuttin deck by pulling the lever backwards to locked position (transport position). 2. Apply the parking brake. This is done as follows: Press down the parking brake pedal (1). Press in the lock button on the steering column (2). Release the parking brake pedal while keeping the button pressed in. The parking brake lock is automatically disengaged when the parking brake pedal is pressed down. The FR 2111, FR 2111 M has the brake pedal and lock button on the right-hand side H 3. On FR 2111, FR 2111 M Put the gear shift lever in the N position (neutral). N IMPORTANT INFORMATION Do not press down the reversing lock button on the lever when engaging the neutral position. Otherwise this will activate the start lock function English 17

20 With a cold engine: 4. Move the throttle to position 3 (choke position). In this position the engine is fed with a richer mixture, which means the engine is easier to start. The throttle must be moved to the side (towards the ignition key) to reach the choke position. DRIVING FR 2116 MA2, move the throttle control to the middle position. FR 2116 MA FR 2116 MA2, if the engine is cold move the choke lever backwards to its end position. FR 2116 MA With a warm engine: 5. Move the throttle in between positions 1 and English

21 DRIVING 6. Turn the ignition key to the start position. IMPORTANT INFORMATION Do not run the starter motor for more than 15 seconds at a time. If the engine does not start wait about 1 minute before trying again. STOP START Once the engine has started release the ignition key back to the neutral position. FR 2116 MA2 Push the choke lever gradually forward when the engine has started. FR 2116 MA Move the throttle to the required engine speed. When Cutting 3/4 to full throttle. WARNING! Never run the engine indoors, in enclosed or badly ventilated areas. Engine exhaust fumes contain poisonous carbon monoxide. STOP START English 19

22 To start an engine with a weak battery DRIVING WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. If jumper cables are used for emergency starting, follow this procedure: IMPORTANT INFORMATION Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower battery to start other vehicles. To attach jumper cables Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery. Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from the fuel tank and battery. To remove cables, reverse order BLACK cable first from chassis and then from the fully charged battery. RED cable last from both batteries. Jumper cables connection English

23 Driving the Rider 1. Release the parking brake by pressing down the brake pedal. DRIVING H 2. On FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Carefully press down one of the pedals until the required speed is obtained. Pedal (1) is pressed down to travel forwards and pedal (2) to reverse. On FR 2111, FR 2111 M Disengage the engine and select the required gear. The lock button must be held in to engage reverse gear. Gears 1-4 are used for Cutting Gears 4-5 are used for transporting Starting can take place independent of which gear is selected. N IMPORTANT INFORMATION Gear changes between forward gears must not be made while the machine is moving. The engine must be disengaged during each gear change. Stop the machine before changing between forward and reverse gears, otherwise this may result in damage to the gearbox. Never use force to engage a gear. If a gear does not engage immediately, release the clutch pedal and press it down again. Now try to engage the gear again English 21

24 DRIVING 3. Select the required cutting height (1-9) using the cutting height lever. In order to obtain an equal cutting height, it is important that the air pressure is the same in both front wheels (60 kpa/8.5 PSI). 4. Press in the lock button on the lifting lever and lower the Cutting deck IMPORTANT INFORMATION The life span of the drive belts is increased significantly if the engine runs at a low speed when the blades are engaged. Therefore only accelerate once the Cutting deck has been lowered into the Cutting position Cutting tips Find and mark out any stones and other fixed objects to avoid colliding with them. Start with a high cutting height and reduce it until the desired Cutting result is obtained. The best Cutting result is achieved with high engine revs (the blades rotate quickly) and low speed (the Rider moves slowly). If the grass is not too long and thick the driving speed can be increased without significantly impairing the Cutting result. The finest lawns are obtained if they are mown frequently. Cutting will be more even and the clippings will be more evenly distributed across the area. The overall Cutting time will not be longer as higher driving speeds can be selected without impairing the Cutting result. Avoid Cutting wet lawns. The Cutting result will be poorer as the wheels will sink into the soft lawn. Rinse off the underside of the Cutting deck after use with water, do not use a high pressure washer. Now put the Cutting deck in the service position. It is extremely important when the Mulching unit is used that the intervals between Cutting are not too long. Cutting pattern WARNING! Clean all stones and other objects that can be thrown by the blades from the lawn. 22 English

25 DRIVING WARNING! Do not use the Rider on ground that slopes more than 15. Mow upwards and downwards on slopes, never sideways. Avoid sudden changes in direction. Starting on slopes, manual gearbox 1. Press down the parking brake 2. Move the throttle to full throttle. 3. Disengage the engine and select 1st gear. 4. Gradually release the clutch pedal. 5. When the engine starts to pull, release the parking brake. MAX Stopping the engine Preferably let the engine idle for a minute so it runs at its normal working temperature before it is stopped if it has worked hard. 1. Lift up the Cutting deck by pulling the lever backwards to its end position FR 2111, FR 2111 M: Pull back the throttle and move the gear shift lever to the neutral position N, without pressing in the reversing lock button. Turn the ignition key to the STOP position. FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2: Pull back the throttle and turn the ignition key to the STOP position. 3. When the Rider is at a standstill, hold down the parking brake and press in the reversing lock button. STOP START Clutch control FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 The clutch control must be pulled out in order for the Rider to be moved when the engine is shutoff English 23

26 MAINTENANCE Maintenance schedule The following is a list of maintenance procedures that must be performed on the Rider. For those points not described in this manual, visit an authorised service workshop. Maintenance = Described in this operator s manual. = Not described in this operator s manual. Page Daily maintenance before starting Cleaning 25 Check the engine oil level 45 Check the engine s cooling air intake 37 Check the fuel pump s air filter 33 Check the steering wires 28 Check the brakes 29 Check the battery 34 Check the safety system 35 Check nuts and bolts Check for any fuel or oil leakage Clean around the silencer Check the silencer 27 Change the engine oil 5) 45 1) 1) Replace the air filter s prefilter 32 Check the mowing deck 38 Check the air pressure in the tyres (60 kpa / 8.5 PSI) 37 Lubricate the belt adjuster 3) 47 Lubricate joints and shafts 3) 47 Adjust the brakes on FR 2111, FR 2111 M 29 Check the V-belts Check the transmission s cooling fins on FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Check the transmission s oil level on FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 46 Adjust the parking brakes on FR 2113MA, FR2115MA, FR 2116 MA, FR 2116 MA2 29 Inspecting and adjusting the throttle cable 30 Clean the engine s and transmission s cooling fins 2,4) Replace the air filter s prefilter and paper filter 2) 32 Replace the fuel filter 31 Replace the spark plug 34 1) First change after 5 hours. Replace after every 25 hours with heavy loads or high temperatures. 2) Under dusty conditions cleaning and replacement should take place more frequently. 3) With daily use, the Rider should be lubricated twice weekly. 4) Performed by an authorised service workshop. 5) Replace the paper element yearly or every 100 hours. Maintenance interval hours WARNING! No service operations may be performed on the engine or Cutting deck unless: The engine has been stopped. The parking brake is actuated. The ignition key has been removed. The Cutting deck is disengaged. The ignition cable has been removed from the spark plug English

27 MAINTENANCE Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry. Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer. Rinse at normal water pressure. Do not direct the jet towards electrical components or bearings. Do not rinse hot surfaces, for example, the engine and exhaust system. It is recommended that you start the engine and run the mower for a short period after cleaning, so that any remaining water is blown off. Lubricate the machine if necessary after cleaning. Carry out extra lubrication when the bearings have been exposed to a degreaser or a water jet IMPORTANT INFORMATION Avoid using a high pressure washer or a steam cleaner There is a major risk of water penetrating into bearings and electrical connections. Corrosion attack can result, which will lead to running problems. Cleaning additives generally aggravate the damage. English 25

28 Dismantling the Rider covers Engine cover The engine becomes accessible for service when the engine cover is folded up. Fold the seat forward, loosen the rubber strap under seat and fold the cover backwards. MAINTENANCE Front cover FR 2111 Remove the bolts holding the front cover (3) and lift off the cover Front cover FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Loosen the snap-in lock and lift off the cover English

29 MAINTENANCE Right-hand wing cover Remove the bolts holding the wing cover (2 and 3). On FR 2113 MA, FR 2115 MA, FR 2116 MA and FR 2116 MA2 the knob (1) should also be removed Left-hand wing cover Remove the bolts holding the wing cover and lift off the cover Inspecting the silencer Check regularly that the silencer is complete and secured correctly. Temperature variations and vibrations can mean that the tightening torque for the screws drops. The screws should be checked when servicing to guarantee the correct torque. The tightening torque should be about 10 Nm. Never use a defective silencer. WARNING! The muffler gets very hot in use and remains so for a short time afterwards. Contact can result in burns. Remember the risk of fire English 27

30 Checking and adjusting the steering wires The steering is governed by means of wires. After a period of use these can become stretched, which means the steering setting may have changed. The steering is checked and adjusted as follows: 1. Dismantle the frame plate by removing the bolts (two on each side). MAINTENANCE Check the tension of the steering wires by squeezing them together by the arrows as illustrated. It should be possible to squeeze the wires so that the distance between them is half the size, without using too much force If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Do not tension the wires too much, they should only be tightened against the steering collar. Support the wire so it does not twist. If you only tension one side the steering wheel s centre position may change. Check the wire tension as set out in point 2 after you have made the adjustment English

31 MAINTENANCE Checking the brake FR 2111, FR 2111 M The brake is a disc brake and is located on the gearbox. Check that the brake is adjusted correctly by measuring the distance between the brake lever and front edge of the cut-out on the chassis. The distance should be 0-1 mm ( ") when the brake is not actuated Adjusting the brake FR 2111, FR 2111 M 1. Loosen the locking nuts (1). 2. Tension the wire using the adjuster screw (2) so that the distance between the brake lever and cut-out s front edge on the chassis is 1 mm (0.040"). 3. Tighten the locking nuts (1) after adjustment Checking and adjusting the parking brake on FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Check that the parking brake is correctly adjusted by placing the Rider on a slight downhill and activate the parking brake. If the Rider does not standstill the parking brake needs adjusting. The parking brake is adjusted as follows: 1. Loosen the locking nuts (1). 2. Tension the cable using the adjuster screw (2) until the play in the cable is taken up. 3. Tighten the locking nuts (1). 4. The parking brake should be checked again after the adjustment has been made H WARNING! A poorly adjusted parking brake can result in reduced braking ability. English 29

32 Adjusting the throttle cable, FR 2111, FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached. 1. Loosen the clamping screw (by the arrow), and slide the throttle to the choke position. MAINTENANCE 2. Pull the throttle cable s casing as far as possible to the right and check that the choke is fully actuated. 3. Tighten the clamping screw Pull back the throttle to the full throttle position and check that the choke is no longer actuated Checking and adjustment of the throttle wire, FR 2116 MA2 Check that the engine responds to the throttle control and that the correct engine speed is achieved at full throttle. If in doubt, contact the service workshop. If adjustment is necessary, adjust the lower wire as follows: 1. Release the clamping screw that secures the wire casing and set the throttle control to full throttle. 2. Check that the throttle wire is attached to the correct hole in the lower lever, see diagram. 3. Pull the throttle wire casing to the far left and tighten the clamping screw English

33 MAINTENANCE Checking and adjusting the choke wire, FR 2116 MA2 If the engine is producing black smoke or is difficult to start then the choke wire (upper wire) may be incorrectly adjusted. If in doubt contact your service workshop. If it is necessary to adjust the choke, proceed as follows: 1. Release the clamping screw that secures the wire casing and set the choke control to maximum choke. 2. Check that the throttle wire is attached to the upper lever, see diagram. 3. Pull the choke wire casing to the far right and tighten the clamping screw Replacing the fuel filter Replace the new fuel filter mounted on the supply line after every 100 hours (once per season) or more frequently if it is clogged. Replace the filter as follows: 1. Fold up the engine cover. 2. Move the hose clips away from the filter. Use a pair of flat pliers. 3. Pull the filter away from the ends of the hose. 4. Press the filter into the ends of the hose. If necessary, a soap solution can be applied to the ends of the filter to simplify assembly. 5. Move the hose clips back towards the filter FR 2116 MA English 31

34 MAINTENANCE Replacing the air filter If the engine seems to lack power or goes irregularly the reason may be that the air filter is clogged. It is therefore important to replace the air filter at regular intervals (see Maintenance schedule for correct service interval). FR 2111, FR 2111 M, FR 2113 MA, FR 2115 MA, FR 2116 MA Replacing the air filter is carried out as follows: Fold open the engine cover. 2. Pull up the handle on the air filter cover, unhook and turn towards the engine. 3. Remove the air filter cover. 4. Lift out the air filter cartridge from the fan housing. Replace the paper filter if it is clogged with dirt. IMPORTANT INFORMATION Do not use compressed air to clean the paper filter. Filters should not be oiled. They should be assembled dry. 5. Carefully lift the precleaner out of the fan housing. Carefully clean the fan housing so that dirt does not fall down into the carburetor. 6. Insert a new precleaner and air filter cartridge in the fan housing. 7. Align the tabs on the cover with the slits in the housing and replace the air filter cover Pull the handle outwards. Secure the handle in the air filter cover and close the cover by pressing it inwards English

35 MAINTENANCE FR 2116 MA2 Replacing the air filter is carried out as follows: 1. Fold open the engine cover. 2. Unhook the fasteners on the sides of the air filter cowling and remove the cowling. 3. Unscrew the knob in the centre of the filter cartridge and remove the filter holder. 4. Carefully remove the pre-cleaner from the cartridge. Replace the pre-cleaner with a new one Lift out the air filter cartridge from the fan housing. Replace the air filter cartridge, if clogged with dirt. Clean the cartridge by carefully tapping it against a flat surface. IMPORTANT INFORMATION Do not use compressed air or solvent with petroleum to clean the cartridge. Filters should not be oiled. They should be assembled dry. 6. Carefully clean the fan housing so that dirt does not fall down into the carburettor. 7. Fit the cartridge, filter holder and then screw on the knob. 8. Slide on the pre-cleaner over the cartridge. 9. Refit the filter cowling Checking the fuel pump s air filter Check regularly that the fuel pump s air filter is not clogged by dirt. The filter can be cleaned using a brush, if necessary. Checking of the fuel pump s air filter, FR 2116 MA2 Check regularly that the fuel pump s air filter is free from dirt. The filter can, when necessary, be cleaned with a brush. Remove the screws and fold out the pump from the bracket. No hoses are to be removed. Reinstall the pump to the bracket FR 2116 MA English 33

36 Checking the acid level in the battery Check that the acid level in the battery lies between the markings. When refilling only distilled water may be used to fill the cells. MAINTENANCE External: Internal: WARNING! Actions with acid contact Rinse thoroughly with water. Drink large quantities of water or milk. Contact a doctor as soon as possible. Eyes: Rinse thoroughly with water. Contact a doctor as soon as possible. The battery emits explosive gases. Sparks, flames and cigarettes must not be present in the vicinity of the battery Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. For the recommended spark plug, see Technical data. IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine. 1. Remove the ignition cable shoe and clean around the spark plug. 2. Remove the spark plug with a 5/8" (16 mm) or13/16" (21 mm) spark plug socket wrench. 3. Check the spark plug. Replace the spark plug if the electrodes are burned or if the insulation is cracked or damaged. Clean the spark plug with a wire brush if it is to be reused. 4. Measure the electrode gap with a gapping tool. The gap should be 0.75 mm (0.030"). Adjust as necessary by bending the side electrode. 5. Reinsert the spark plug, turning by hand to avoid damaging the threads. 6. After the spark plug is seated, tighten it using a spark plug wrench so that the washer is compressed. A used spark plug should be turned 1/8 of a turn from the seated position. A new spark plug should be turned 1/4 a turn from the seated position. 7. Replace the ignition cable shoe. IMPORTANT INFORMATION Inadequately tightened spark plugs can cause overheating and damage the engine. Tightening the spark plug too much can damage the threads in the cylinder head. IMPORTANT INFORMATION Do not turn over the engine if the spark plug or ignition cable has been removed. 34 English

37 MAINTENANCE FR 2111, FR 2111 M Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the Cutting deck is in its raised position and the gear shift lever or hydrostat pedals are in the neutral position. The driver does not need to be seated in the driver s seat. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again. Check that the engine stops if you temporarily move out of the driver s seat while the Cutting deck is lowered or the gear shift lever/hydrostat pedals are not in the neutral position. Starter Ignition system Works Does not work N FR 2111, FR 2111 M English 35

38 MAINTENANCE FR 2113 MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the Cutting deck is in its raised position and the gear shift lever or hydrostat pedals are in the neutral position. The driver does not need to be seated in the driver s seat. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again. Check that the engine stops if you temporarily move out of the driver s seat while the Cutting deck is lowered or the gear shift lever/hydrostat pedals are not in the neutral position. Starter Ignition system Works Does not work FR 2113MA, FR 2115 MA, FR 2116 MA, FR 2116 MA2 36 English

39 MAINTENANCE Main fuse The fuse is located in a loose holder under the battery case cover, in front of the battery. Type: Flat-blade mounting, 15 A. Do not use any other type of fuse when replacing. A blown fuse indicates that the mounting has burnt off. Pull the fuse out of the holder when replacing. The fuse is used to pro ect the electrical system. If it blows again shortly after replacing this is due to a short circuit, which must be rectified before the machine is used again Checking the tyres air pressure The tyres air pressure should be 60 kpa (0.6 kp/cm 2 /8.5 PSI) on all wheels. In order to improve the drive power the pressure in the rear tyres can be reduced to 40 kpa (0.4 kp/cm PSI). The highest permitted pressure is 100 kpa (1.0 kp/cm 2 /14 PSI). IMPORTANT INFORMATION Different air pressure in the front tyres will result in the blades Cutting the grass at different heights Checking the engine s cooling air intake Clean the air intake grille in the engine cover behind the driver s seat. Fold up the engine cover. Check that the engine cooling air intake is free of leaves, grass and dirt. Check the air duct, located on the inside of the engine cover, ensure it is clean and does not rub against the cooling air intake. A clogged air duct or cooling air intake impairs the cooling of the engine, which may result in engine damage. Air intake grille WARNING! The cooling air intake rotates when the engine is running. Mind your fingers. Cooling air intake English 37

40 MAINTENANCE Checking and adjusting the Cutting deck s ground pressure on FR 2113 MA, FR 2115 MA, FR 2116MA, FR 2116 MA2 In order to achieve the best Cutting result the Cutting deck should follow the ground without touching it too heavily. The pressure is adjusted using a screw on each side of the Rider. 1. Check that the tyres air pressure is 60 kpa (0.6 kp/cm 2 /8.5 PSI). 2. Place a pair of bathroom scales under the Cutting deck s frame (on the front edge) so that the Cutting deck rests on the scales. If necessary a block can be placed between the frame and the scales so that the support wheels do not support any weight Adjust the Cutting deck s ground pressure by screwing the adjuster screws, which are located behind the front wheels on both sides, in or out. The ground pressure should be between 12 and 15 kg ( lbs) Checking the parallelism of the Cutting deck Check the Cutting deck s parallelism as follows: 1. Check that the tyres air pressure is 60 kpa (0.6 kp/cm 2 /8.5 PSI). 2. Place the Rider on a flat surface. 3. Measure the distance between the ground and the front and back edges of the deck cover. The Cutting deck should have a slight slant, with the rear edge 2-4 mm (1/8") higher than the front edge English