Nomenclature. General Format: C-D-M

Size: px
Start display at page:

Download "Nomenclature. General Format: C-D-M"

Transcription

1 WARNING: THIS LIST IS NOT GUARANTEED TO BE ACCURATE NOR UP TO DATE. THIS IS NOT SUPPORTED BY OR ENDORSED BY TEXTRON LYCOMING. DO NOT USE ANY OF THIS INFORMATION FOR THE OPERATION OR MAINTENANCE OF ANY AIRCRAFT ENGINE. THIS INFORMATION IS PRESENTED FOR EDUCATIONAL PURPOSES ONLY Nomenclature Lycoming's specific convention for post-wwii aircraft piston engine designation is as follows. Note that this convention is fairly standard and applicable to many other manufacturers. General Format: C-D-M Where: C Letters indicating the engine's configuration: I O X R G T S L A AE M H V Fuel injected Opposed type (pancake-style) X-type engine Radial type engine Engine is geared Engine is turbocharged Engine is supercharged Engine is left-turning Engine is designed for aerobatics (DRY SUMP) Engine is designed for aerobatics (WET SUMP) Engine is designed for unmanned drone (UNCERTIFIED) Engine is designed for helicopter installation Engine is designed to have the crankshaft in the vertical, not horizontal, plane. Usually implies "H" D The engine's displacement in cubic inches.

2 M Configuration. Includes power rating, nose section, accessory section, counterweight application, and magneto application. Example from the Lycoming Overhaul manual: TIO-541-E1B4D Where: TIO - The prefix as described above The engine's cubic inch displacement, as described above. A 1 at the end indicates an integral accessory drive (e.g. TIO-541) except for the 76 series engines (see below). E - Power section and power rating for the displacement 1 - Nose section (provisions for a prop governor, hollow/solid crankshaft, prop governor location) B - Accessory section (fuel pump type, accy pad(s), etc.) 4 - Counterweight application (if applicable, see the power section to determine this) D - Dual magneto (if applicable) PISTON - (4) FOUR CYLINDER SERIES Model C1 C1B C1C C2A C2B HP T/O RPM Fuel C.R. DESCRIPTION :1 Basic engine : : : :1 Same as -C1 with Retard Breaker Same as -C1 but with Slick Same as -C1 but has AS-127, Type 1 flange Same as -C2A with series Suffi x

3 C2C :1 Similar to -C2A but with Slick E :1 Same as -C1 but has provision for controllable prop. E1B :1 Same as -C1B but has provision for controllable prop. E2A :1 Same as -C2A but has provision for controllable prop. E2B :1 Same as -C2B but has provision for controllable prop. F /100LL 9.70:1 Similar to -C1 but higher power and comp. ratio F1B /100LL 9.70:1 Similar to -C1B but higher power and comp. ratio F2A /100LL 9.70:1 Similar to -C2A but higher power and comp. ratio F2B /100LL 9.70:1 Similar to -C2B but higher power and comp. ratio G /100LL 9.70:1 Same as -F1 but with provision for controllable prop. G1B /100LL 9.70:1 Same as -F1I but with provision for controllable prop. G2A /100LL 9.70:1 Same as -F2A but with provision for controllable prop. G2B /100LL 9.70:1 Same as -F2B but with provision for controllable prop. H2C :1 Same as -C2C but with Type 1 dynafocal mounts J2A /100LL 9.70:1 Same as -F2A but with Type 1 dynafocal mounts J2B /100LL 9.70:1 Same as -F2B but with Hope 1 dynafocal mounts K2A /100LL 8.50:1 Same as -F2A but with 20_ BTC timing, lower comp. ratio and lower power K2B /100LL 8.50:1 Same as -F2B but with 20_ BTC timing, lower comp. ratio and lower power K2C /100LL 8.50:1 Same as -K2A but with Slick

4 L2A L2C M1 M2C M3C N2A N2C P1 P2A P2C P3C Model O-290- D O O-290- D2 O-290- D2A O-290- D2B O-290- D2C /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.10: O0/100LL 8.10: /100LL 8.10: /100LL 8.10: O/100LL 8.10: OO/100LL 8.10:1 HP T/O RPM Same as -J2A but with 20_ timing, lower comp. ratio and lower power Same as -L2A but with Slick Similar to -L2A but with provision for controllable prop. and has AS-127, Type 2 prop. flange Similar to -M1 but has AS-127, Type 1 flange and Slick magnetos. Similar to -M1 but has Slick magnetos and uses 7/16 inch bolts instead of 3/8 inch bolts. Same as -L2A but lower comp. ratio and power Same as -L2C but lower comp. ratio and power Same as -M1 but lower comp. ratio and power Similar to -P1 but has AS-127, Type 1 flange Same as -M2C but lower comp. ratio and power Same as -M3C but lower comp. ratio and power Fuel C.R. DESCRIPTION Suffix :1 Solid tappets, Hydro control :1 Same as O-290-D : : : :1 Hydraulic tappets, 18 degree spark advance Same as -D2 but new crankcase for controllable prop. Same as -D2, 25_ spark advance and lower C.R. Same as -D2B with Retard Breaker

5 Model A1A A1B A2A A2B A2C A2D A3A A3B A3C B1A B1B B2A B2B B2C B2D B3A B3B HP T/O RPM Fuel C.R. DESCRIPTION Suffix Controllable, 25 degree spark advance Bendix S4LN-20 and S4LN-21 Same as -A1A with straight riser in oil sump and -32 carburetor Same as -A1A but fixed pitch Same as -A2A with straight riser in oil sump and -32 carburetor Same as -A2B with Retard Breaker Same as -E3D but with conical mounts and A sump and intake pipes Same as -A1A but uses 7/16 in. dia. bolts Same as -A3A except for straight riser in oil sump and -32 carburetor Same as -A3B except for Retard Breaker Same as -A1A but high C.R I00/100LL 8.50:1 Same as -B1A except for straight riser in od sump and -32 carburetor Same as -B~ fixed pitch /100u 8.50:1 Same as -B2A except for straight riser in oil sump and -32 carburetor Same as -B2B except for Retard Breaker Same as -DID except fixed and conical mounts Same as -B1A except for 7/16 inch attaching bolts Same as -B~ except for 7~6 inch attaching bolts and straight riser in oil sump and -32 carburetor Same as -B3B except for Retard

6 B3C C1A C1B C2A C2B C2C C3A C3B C3C D1A D1B D1C D1D D1F D2A D2B D2C D2F D2G Breaker Low compression field service conversion of -B1A Low compression field service conversion of -BIB Low compression field service conversion of -B2A Low compression field service corrversion of -B2B Low compression field service conversion of -B2C Low compression field service conversion of -B3A Low compression field service conversion of -B3B Low compression field service conversion of -B3C Same as -B3B but with Type 1 dynafocal mounts Same as -D~ except for Retard Breaker Same as -D2C but with provision for controllable prop. Similar to -D1A but has horizontal carburetor and in- duction housing and has Slick Same as -E1F except has high compression pistons Same as -DIA but with fixed pitch and 3/8 in. attaching bolts Same as -D2A except for Retard Breaker Same as -D2A except for series Same as -E2F except has high compression pistons Same as -D2A but with Slick, 7/16 instead of 3/8 in. flange bolts Same as -D2G but with B

7 D2H D2J D3G E1A E1B E1C E1F EU E2A E2B E2C E2D E2F E2G E2H E3D 150/ / :1 150/ 140 sump and intake pipes and has provision for AC type fuel pump Similar to -D2G but has (2) Slick impulse coupling magnetos and an unmachined governor pad on front of crankcase Same as -D2G but with 3/8 in. attaching bolts and has provisions for fuel pump Same as -A3B but with Type 1 dynafocal mounts Same as -ETA except for Retard Breaker Same as -ETA but has series Same as -E1C but with governor drive on left front of crankcase Same as -E1F but has Slick Same as -ETA but with fixed pitch and uses 3/8 inch attaching bolts and has alternate rating of 140 at 2450 RPM. Same as -E2A except for Retard Breaker 2700/ :1 Same as -E2A but has series Similar to -E2A but with Slick, O-235 front main bearing and 7/16 inch flange bushings Same as -E1F but with fixed pitch Same as -E2D but has A sump and intake pipes Same as -E2D but equipped with S4LN-20 and -21 Mags. Same as -E2D but uses 3/8 inch instead of 7/16 inch flange bushings

8 E3H H1AD H1BD H2AD H2BD H3AD H3BD I A1A I A2A I B1A I B1B I B1C I B1D I B1E I B2A I C1A /100LL 9.00: /100LL 9.00: /100LL 9.00: /100LL 9.00: /100LL 9.00: /100LL 9.00:1 Same as -E3D but equipped with S4LN-20 and -21 Mags. Integral accessory section ciankcase, front mounted fuel pump, external mounted oil pump and D4RN-3000 impulse coupling dual magneto Same as -H1AD but with D4RN-3200 retard breaker dual magneto Same as -H1AD but with fixed pitch Same as -H2AD but with D4RN-3200 retard breaker dual magneto Same as -H2AD but uses 3/8 inch instead of 7/16 inch flange bushings Same as -H3AD but with D4RN-3200 retard breaker dual magneto Same as E1B but with rear Bendix fuel injection and Type 2 dynafocal mounts Same as -A1A but with fixed pitch and 3/8 inch flange bushings Same as D1A but with Type 2 dynafocal mounts and rear mounted Bendix fuel injector Same as -B1A but has AN fuel pump drive Same as -B1A but has adapter for mounting fuel injector straight to the rear Same as -B1C but with series Retard Same as -D1C but with rear mounted horizontal fuel injector Same as -B1A but with fixed pitch and 3/8 inch flange bushings Same as -B1A except converted for use with turbocharger, long reach

9 I ClB I D1A I D1B I D1C I E1A I E1B I E2A I E2B I F1A /10OLL 8.50:1 spark plugs, piston cooling oil jets, vented fuel nozzles, two S4LN-21 impulse coupling magnetos and AN fuel pump drive Same as -CIA but with fuel injector mounted straight to the rear and 24 volt system standard Same as D2C except has Bendix RSA-5AD1 fuel injector, provision for controllable and 7/16 inch flange bushings Same as -D1A but with governor drive on left front of crankcase Same as -D1B but with Slick, 24 volt system and 100 amp alternator standard Same as A3B except has Bendix fuel injector Same as -ETA but with Slick Same as -ETA but with fixed pitch and 3/8 inch flange bushings Same as A2D but with Bendix RSA-5AD1 fuel injector Same as -CIA but with Type 1 dynafocal mounts LIO- 320-BlA Similar to IBL~ but has left hand rotation crankshaft LIO C1A AIO A1A AIO A1B Similar to IC1A but has left hand rotation crankshaft Aerobatic engine with performance similar to ID Same as -A1A but has impulse coupling Magneto AIO- Same as -A1A but with fixed pitch

10 320- A2A AIO A2B AIO B1B AIO C1B 320- D1B 320- D2B 320- E1A 320- E1B 320- E2A 320- E2B Model O-340- A1A O-340- A1B O-340- A2A O-340- B1A O-340- B2A HP T/O RPM Same as -A2A but has impulse coupling Magneto Similar to -A1B but with front mounted fuel injector Similar to -BIB but the fuel injector is vertically mounted on the bottom of the sump Same as ID1B but is equipped with Aerobatic kit Same as -D1B but with fixed pitch Same as IE1A but is equipped with Aerobatic kit Same as IE1B but is equipped with Aerobatic kit Same as IE2A but is equipped with Aerobatic kit Same as IE2B but is equipped with Aerobatic kit Fuel C.R. DESCRIPTION Suffix /100LL 8.50:1 Controllable /100LL 8.50: /100LL 8.50:1 Same as -A1A except for Retard Breaker Same as -A1A but fixed pitch :1 Low compression -AL :1 Low compression -A2A

11 O0- A1A O0- A1AD O0- A1C O0- A1D O0- A1F O0- A1F6 O0- A1F6D O0- A1G O0- A1G6 O0- A1G6D O0- A1H O0- A1H6 O0- A1LD O0- A1P* O0- A2A O0- A2D O0- A2E Dynafocal mounts Same as -A1A but with D4LN-3000 impulse coupling dual magnetos Similar to -A1A but has horizontal induction housing, Bendix PSH-5BD pressure carburetor and retard breaker magnetos Same as -A1A except for Retard Breaker Same as -ALA with series Same as -A1F but has (1) sixth and (V eighth order counterweights Same as -A1F6 but with D4LN-3000 impulse coupling dual magnetos Similar to -A1F but has horizontal carburetor and induction housing Same as -A1G but has (1) sixth and (1) eighth order counterweights Same as -A1G6 but with D4LN-3000 impulse coupling dual magneto Same as -A1G but with governor drive on left front of crankcase and -21, -204 magnetos Same as -A1H but has (1) sixth and (1) eighth order counterweights Similar to -A1A but with D4LN-3000 impulse coupling dual magneto and has governor drive on left front of crankcase Same as -C1G except dynafocal mounts Same as -A1A but fixed pitch Same as -A2A except for Retard Breaker Same as -A2D with provision for AN fuel pump drive O0- Same as -A2A with series

12 A2F O0- A2G O0- A2H O0- A3A O0- A3AD O0- A3D O0- A4A O0- A4AD O0- A4D O0- A4G O0- A4J O0- A4K O0- A4M O0- A4N O0- A4P* O0- A5AD O0- B1A O0- B1B I00/100LL 8.50: /1O0LL 8.50: O0/100LL 8.50: : :1 Same as -A1G but fixed pitch Same as -A1H but has fixed pitch Same as -A2A but has 6 special long bushings in flange Same as -~ but with D4LN-3000 impulse coupling dual magneto Same as -A3A except for Retard Breaker Same as -A3A but has solid crankshaft Same as -A4A but with D4LN-3000 impulse coupling dual magneto Similar to -A4A except with Retard Breaker, (2) magneto drive isolators and -A2A flange bushings Same as -A2G but has -A4A crankshaft with -A2G flange bushings Same as -A4G but has -21 and -204 Same as -A4J but with Slick Same as -A4A but with Slick Same as -A4M but has an unmachined governor pad on front of crankcase and -A2G flange bushings Same as -A4M except for flange bushings Same as -A4AD but has standard length flange bushings Same as -A1A but low compression ratio Same as -B1A except for Retard Breaker

13 O0- B2A O0- B2B O0- B2C O0- C1A O0- C1C O0- C1E O0- C1F O0- C1G O0- C2A O0- C2B O0- C2C O0- C2D O0- C2E O0- C4F O0- C4P O0- D1A O0- D2A O0- D2B : : : O0/100LL 8.50: : : :1 Same as -B1A except for fixed pitch Same as -B2A except for Retard Breaker Same as -B2A except has IO0-A crank and rods Same as -A1A but conical rubber mounts Same as -CIA except for Retard Breaker Same as -CIA but with Slick Same as -A1G with conical mounts and Slick magnetos Same as -CIA but with governor drive on left front of crankcase Same as -CIA but fixed pitch Same as -CIA but fixed pitch and horizontal pressure carburetor and has helicopter rating Same as -C2A except for Retard Breaker Same as -C2B except for Retard Breaker Same as -C2A but with Slick Same as -C1F except has solid crankshaft and no provision for governor Same as -A4M except for flange bushings and conical mounts Same as -B1A but conical rubber mounts and series magnetos Same as -B2A but conical rubber mounts Same as -D2A except for Retard Breaker O /100LL 9.00:1 Integral accessory section -77

14 E1A6D O0- F1A6 O0- G1A6 HO- A1A HO- B1A HO- B1B IO0- A1A IO0- A1B IO0- A1B6 IO0- A1B6D IO0- A1C IO0- A1D IO0- A1D6 IO0- A1D6D /100LL 8.50: /100LL 8.50:1 crainkcase, front mounted fuel pump, external oil pump, D4RN-3000 impulse coupling dual magnetos and counterweighted crankshaft Similar to O0-A series with new sump for nose wheel clearance, rear HA-6 carburetor, has (1) sixth and (1) eigth order counterweights and has governor drive on left front of crankcase Same as -F1A6 but with a machined pad on right front of crankcase Same as 00-A2D but with MA-4- SAA carburetor and type 2 dynafocal mounts Same as 00-C2D except for rated speed Same as -B1A but with two (2) S4LN-200 Bendix fuel injection, tuned induction /10OLL 8.70:1 Same as -A1A but has series impulse coupling magnetos Same as -A1B but has (1) sixth and (1) eighth order counterweights Same as -A1B6 but has (1) Bendix D4LN-3000 impulse coupling dual Magneto Same as -A1A but with series Same as -A1B but has S4LN-21 impulse coupling and S4LN-204 Same as -A1B6 but with governor drive on left front of crankcase Same as -A1D6 but has (1) Bendix D4LN-3000 impulse coupling dual magneto

15 IO0- A2A IO0- A2B IO0- A2C IO0- A3B6 IO0- A3B6D IO0- A3D6D IO0- B1A IO0- B1B IO0- B1C IO0- B1D IO0- B1E IO0- B1F IO0- B1F6 IO0- B2E IO0- B2F IO0- B2F6 IO0- B4A /100LL 8.50: /1OOLL 8.50:1 Same as -A1A but fixed pitch Same as -A2A but has series impulse Same as -A1C but has fixed pitch Same as -A1B6 with flange bushings rotated 120 degrees clockwise Same as -A1B6D but with locating bushings rotated 120 degrees clockwise Same as -A1D6D but with locating bushings rotated 120 degrees clockwise Same as O0-A1D except for Simmonds 530 Fuel Injection System Same as -B1A except for Bendix Fuel Injection System Conversion of O0-A1C to Bendix Fuel Injection Same as -BIB but with AN fuel pump drive Similar to -BIB with rear mounted fuel injection and series impulse coupling magnetos Similar to -BIB except has (2) Same as -B1F but with one (V sixth and (1) eighth order counterweights Same as -B1E but has Wed pitch Same as -B1F but fixed pitch Same as -B2F but with one a) sixth and one (1) eighth order counterweights Similar to -BIB but has S4LN-21 (impulse coupling) and S4LN-20 magnetos and O0-A4A solid crankshaft

16 IO0- C1A IO0- C1B IO0- C1C IO0- C1C6 IO0- C1D6 IO0- C1E6 IO0- C1E6D IO0- C1F IO0- D1A IO0- E1A IO0- FlA IO0- J1AD IO0- J1A6D IO0- K2A LO0- A1G6D LO0- A1H6 Same as -A~ but with rear air inlet I00/100LL 8.70: /1OOLL 8.70: /10LL 8.70:1 Same as -CIA but with series Similar to -C1B but has 14_ injector adapter and impulse Magneto Same as -C1C but with one (1) sixth and one (1) eighth order counterweights Similar to -C1C but has straight injector inlet and has (1) sixth and (1) eighth order counterweights Similar to -C1C but has governor drive on left front of crankcase, has (1) sixth and (1) eighth order counterweights Same as -C1E6 but with D4LN-3000 impulse coupling dual Magneto Same as -C1C but with AN fuel pump drive and pump Same as -C1B but has Type 2 dynafocal mounts Similar to -B1E but has Type 2 dynafocal mounts and Retard Breaker Similar to -B1E except converted for use with turbocharger Similar to -A1B except equipped with a D4LN-3000 dual magneto and has a rear type engine mount similar to TO0-F1A6D Same as -J~D but with O) sixth and (1) eighth order counterweights. Same as -A2A but has Bendix S4LN- 21 impulse coupling and S4LN-20 magnetos and provision for straight conical mounts Similar to O0-A1G6D but has left hand rotation crankshaft Similar to O0-A1H6 but has left hand rotation crankshaft

17 LO0- E1A6D TO0- A1A6D TO0- C1A6D TO0- E1A6D TO0- F1A6D VO- A1A VO- A1B VO- B1A AIO- A1A AIO- A1B AIO- A2A AIO- A2B AIO- B1B HIO /100LL 9.00: /100LL 8.00: /100LL 7.30: /100LL 8.00: /100LL 7.30: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.70:1 Similar to O0-ELA6D but has left hand rotation crankshaft Similar to 00-A1F6D but with HA- 6 horizontal carburetor ahead of Rajay turbocharger, lower speed, lower C.R. and higher power Similar to -A1A6D except for rating, compression ratio, carburetor and turbocharger location and turbocharger controls Similar to O0-ELA6D but with AiResearch TA04 Turbocharger, lower speed and lower compression ratio Same as -C1A6D with long type 1.12,, conical mount Vertical crankshaft (Brantly Modification) Same as -A1A except for altitude compensated carburetor and retard Breaker Same as -A1B but with piston cooling oil jets Aerobatic engine with performance similar to IO0-A1A Same as -A1A but has impulse Same as -A1A but does not have provision for controllable Same as -A2A but has impulse Similar to -A1B but with front mounted fuel injector Rated power to 3900 feet, imilar to HO0-B1B but has Bendix fuel

18 A1A HIO- A1B HIO- B1A HIO- B1B HIO- C1A HIO- C1B HIO- D1A HIO- E1AD HIO- E1BD HIO- FlAD IVO- A1A LIO- C1E6 LTO- A1A6D LTO- E1A6D /100LL 8.70: /100LL 8.50: /100LL 8.50: /100LL 8.70: /100LL 8.70: /100LL 10.00: /100LL 8.00: O0/100LL 8.00: /100LL 8.00: /100LL 8.50: /100LL 8.00: /100LL 8.00:1 injector, angle valve cylinders and higher C.R. Similar to -A1A except conical mounts, no AMC unit on fuel injector and 90_ fuel injector mount Similar to HO0-B1B but has Bendix fuel injector and dual diaphragm fuel pump Same as -B1A but has AN fuel pump drive Similar to -A1A but has higher sea level rating and type 2 dynafocal mounts Same as -CIA but has series Similar to -A1A but has series and Bendix RSA-7AA1 fuel injector Similar to -CIA except for compression ratio, rating D4LN-3000 impulse coupling dual magneto and provision for turbocharging Same as -E1AD but has D4LN-3200 Retard Breaker Magneto Similar to -E1AD but has heavier crankshaft, and higher RPM Same as VO0-B1A but with Bendix Fuel Injection Similar to IO0-C1E6 but has left hand rotation crankshaft Similar to TO0-MA6D but has left hand rotation crankshaft Similar to TO0-E1A6D but has left hand rotation crankshaft

19 TIO- A1A TIO- A1B TIO- A3B6 TIO- C1A6D LHIO- C1A LHIO- C1B LHIO- F1AD A1A A1B A1B6 A1C A1D A1E /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 8.70: /100LL 8.70: /100LL 8.00:1 Similar to IO0-C1B but has turbocharger (TE0659) and lower rated speed Same as -A1A but does not have suck-open door Similar to -A1B but has (1) sixth and (1) eighth order counterweights, provision for 3-bladed, large fuel pump, conduit harness and pressurized Mags. Same as TO0-C1A6D but has a Bendix RSA-5AD1 Fuel Injector Similar to HIO0-C1A but has left hand rotation crankshaft Similar to HIO0-C1B but has left hand rotation crankshaft Similar to HIO0-F1AD but has left hand rotation crankshaft Same as IO0-A1A but is equipped with Aerobatic kit Same as IO0-A1B but is equipped with Aerobatic kit Same as IO0-A1B6 but is equipped with Aerobatic kit Same as IO0-A1C but is equipped with Aerobatic kit Same as IO0-A1D but is equipped with Aerobatic kit Same as -AID but with prop. governor drive on left front of crankcase /l00LL 8.70:1 Same as -ATE but has (1) sixth and

20 A1E6* A2A A2B A2C B1B B1D B1F B1F6 B1G6 B2F B2F6 B4A H1A /lO0LL 8.70: /l00LL 8.70:1 (1) eighth order counterweights Same as IO0-A2A but is equipped with Aerobatic kit Same as IO0-A2B but is equipped with Aerobatic kit Same as IO0-A2C but is equipped with Aerobatic kit Same as IO0-B1B but is equipped with Aerobatic kit Same as IO0-B1D but is equipped with Aerobatic kit Same as IO0-B1F but is equipped with Aerobatic kit Same as IO0-B1F6 but is equipped with Aerobatic kit Same as -B1F6 but with Slick Same as IO0-B2F but is equipped with Aerobatic kit Same as IO0-B2F6 but is equipped with Aerobatic kit Same as IO0-B4A but is equipped with Aerobatic kit Similar to 00-C2E but with provision for controllable, an RSA-5AD1 fuel injector, high pressure fuel pump and is equipped with Aerobatic kit

21 PISTON (6) SIX CYLINDER SERIES Model HP T/O RPM O-435-A O-435- A2 Fuel C.R. DESCRIPTION Suffix 6.50:1 Rear mounted automotive type accessories /100LL 7.50:1 Same as -A except C.R. -17 O /100LL 6.50:1 GO-435- C2(11) GO-435- C2(11A) GO-435- C2(11B) GO-435- C2A GO-435- C2A2 GO-435- C2B GO-435- C2B1 GO-435- C2B2 GO-435- C2B26 GO-435- C2E VO-435- A1A (O ) VO-435- A1B : : : :1 Kaman Helicopter Std. rear mounted accessories less 35-KV generator drive Fuel grade depends on carburetor setting Ryan Navion MA-4-5 carburetor _ Beech, PS-5 carburetor, dual governor and vacuum pump drive Aero Commander; PS-5 carburetor no dual drive Std. -C2 with dry sump, heavy magnetos (Swiss engines) have -C2B reduction gear, PS-5 carburetor A -11B -11C :1 -C2A have lightweight magnetos -11C :1 Std. -C2 with governor drive integral with reduction gear :1 -C2B with angle generator drive :1 -C2B with lightweight magnetos :1 -C2B2 with 6th order counterweight : : :1 Fuel grade depends on carburetor setting GO-435-C2 with lightweight magnetos Helicopter; crosswise accessory MA-4-5 carburetor, S6RN-20 and S6RN-21 magnetos (used GSO0 accessory housing) Helicopter; redesigned accessory housing (crosswise) S6LN-20, S6LN- - 11BA - 11BA - 11BA - 11BA - 11AA

22 VO-435- A1C VO-435- A1D VO-435- A1E VO-435- A1F VO-435- B1A O O A O B O C : : : : /100LL 8.70: : : : :1 O :1 O-435-6A O : /100LL 7.30:1 21 magnetos, hand starter, no fuel pump or hydraulic pump drive -A1B with wrap around crankcase, new oil sump fuel and hydraulic pump drive no hand starter AN-I magnetos and harness optional -A1B with wrap around crankcase and 4 pad oil sump -AID except for Retard Breaker Similar to -ATE but has piston cooling oil jets and heavy heads, convertible to TVO-435-A1A High compression wet sump engine with redesigned crosswise accessory section -A1B with fuel and hydraulic pump drives, AN-I harness and magnetos, no hand starter (256 to 283 had -20 and -21 magnetos) -23 with wrap around crankcase and 4 pad sump -23A with altitude compensating carburetor Same as -23B except has spring coupling accessory drive -A1B with AN-I harness and magnetos, altitude compensating carburetor Same as with wrap around crankcase and 4 pad sump Military version of TVO-435-BLA with TVO-435-A1A rating 15, RPM, TVO- 435-A1A /100LL 7.30:1 turbocharged vertical helicopter engine 14, RPM, TVO- 435-B1A /100LL 7.30:1 turbocharged vertical helicopter engine TVO- 435-B1B /100LL 7.30:1 Same as -B1A except for series

23 16,000 feet ~ 3200 RPM, TVO- 435-C1A /100LL 7.30:1 turbocharged vertical helicopter engine Same as -B1A but has TE0659 TVO- 435-D1A /100LL 7.30:1 Turbocharger and series magnetos TVO- 435-D1B TVO- 435-E1A TVO- 435-FlA TVO- 435-G1A TVO- 435-G1B Model GO0- B GO0- B1A6 GO0- B1B GO0- B1C GO0- B1D GO0- C1B6 GO0- C1D6 GO0- C2C6 GO0- C2D6 GO0- C2E /100LL 7.30:1 Same as -D1A but has -200 series /100LL 7.30:1 Similar to -~ but has TE0659 Turbocharger /100LL 7.30:1 Similar to -D1A but has wet sump and higher rating /100LL 7.30:1 Same as -D1A but has 280 HP rating /100LL 7.30:1 Same as -G1A but has -200 series HP T/O RPM Fuel C.R. DESCRIPTION Suffix : : :1 High speed straight through generator drive and lightweight magnetos GO0-B with one sixth order and five third order counterweights GO0-B with low speed generator drive and heavy magnetos (GO-435- C2B with 5-1/8 in. bore) :1 GO0-B with angle generator drive : /100LL 8.70: /100LL 8.70:1 GO0-B1B with lightweight magnetos Dry sump, crosswise accessones (H. C. GO0-D) High compression GO0-B1D with 1.75 venturi carburetor /100LL 8.70:1 High compression GO0-F /100LL 8.70:1 -C2C6 with lightweight magnetos /100LL 8.70:1 -C2D6 with angle generator drive (GO- B1C accessory housing) GO :1 Crosswise accessones, dry sump,

24 D1A GO0- F6 GO0- F1A6 GO0- F2A6 GO0- F2D6 GO0- F3A6 GO0- F3B6 GO0- F4A6 GO0- F4B6 GO0- G1A6 GO0- G1B6 GO0- G1D6 GO0- G1H6 GO0- GU6 GO0- G2D6 GO0- G2F :1 lightweight magnetos, PS-5 carburetor with 1.75 venturi fuel pump and hydraulic pump drives GO~B1B with flanged shaft sixth order counterweight 1.75 venturi carburetor :1 -F6 with lightweight magnetos : : :1 -F1A6 with 20 spline prop. shaft and single oil supply Conversion of -G1D6 to low compression for turbocharging Low compression GO0-C2D6 (Conversion) :1 Low compression GO0-C2C : : /100LL 8.70: /100LL 8.70:1 -F~ with shaft converted to single oil supply for Hartzell with conversion kit P/N or shaft no or no Reduction Gear Assembly GO0-F6 with shaft converted to single oil supply for Hartzell with conversion kit P/N or shaft no or no Reduction Gear Assembly High compression GO0-B1A6 piston cooling oil jets GO0-C1B6 with piston cooling oil jets /100LL 8.70:1 -C1D6 with piston cooling oil jets /l00LL 8.70: /100LL 8.70: /100LL 8.70: O0/100LL 8.70:1 Same as -G1D6 but with angle generator drive Same as -G1A6 but with series GO0-C2D6 with piston cooling oil jets Same as -G2D6 except for Retard Breaker

25 IGO0- A1A6 IGO0- A1B6 GSO- A1A6 GSO- A1C6 GSO- A2A6 GSO- B1A6 GSO- B1B3 GSO- B1B6 GSO- B1C6 GSO- B1E6 GSO- B1F6 GSO- B1G6 GSO- BU6 GSO- B2C6 GSO /100LL 8.70: /100LL 8.70:1 Similar to GO0-GU6 but has Bendix RSA-5AD1 fuel injector Similar to GO~80-G1A6 but has Bendix RSA-5AD1 fuel injector Supercharged, dry sump, crosswise accessories, lightweight magnetos Same as -A1A6 except for supercharger inlet thermocouple Conversion of -A1A6 to flanbed reduction gear for reversible GSO~80-A1A6 with piston cooling oil jets, and updraft carburetor Same as -B1H6 except Torsional Damper System has been modified GSO0-B1A6 with horizontal elbow and carburetor under engine GSO0-B1A6 with horizontal carburetor mounted directly on straight thru air inlet supercharger housing Same as -B1A6 except for Retard Breaker Same as -B1B6 except for Retard Breaker Same as -B1C6 except for Retard Breaker Same as -B1A6 but with series Same as -B1C6 but with flanged reduction gear for reversible GSO0-B1A6 with flange shaft and down- draft PSD-78D

26 B2D6 GSO- B2G6 GSO- B2H6 O0-1**,-1A IGSO- AlA6 IGSO- A1B6 IGSO- A1C6 IGSO- A1D6 IGSO- A1E6 IGSO- A1F3 IGSO- A1F6 IGSO- A1G /100LLL 7.30:1 carburetor Same as -B2C6 with Retard Breaker Same as -B2D6 except for Retard Breaker Like Beech version of GSO0-B1B6 (Horizontal carburetor under engine) with -22 and -23 magnetos Simmonds Fuel Injection Version of GSO~80-B1B /100LL 730:1 O /~00LL 7.30:1 Model ALA HP 250/ 235 T/O RPM 2575/ 2400 Same as -A1A6 except for Retard Breaker Same as -A1A6 except for horizontal air inlet housing and throttle body Conversion of GSO0-B1A6 to Bendix fuel injection Same as -A1D6 except for air inlet housing mounts injector 35 deg. forward of vertical and has Retard Breaker Same as -A1F6 except Torsional Damper System has been modified Same as -A1C6 except for Retard Breaker Similar to -A1E6 but has series and has fuel flow modulator removed IGSO0-A1A6 but with -22 and -23 magnetos A Fuel C.R. DESCRIPTION Suffix 100/100LL 8.50:1 Two sixth order counterweights 250/ 2575/ 100/100LL 8.50:1 Same as A1A but one fifth and

27 A1A one sixth order counterweights A1B5 A1C5 A1D A1D5 A2B A3D5 A4A5 A4B5 A4C5 A4D5 B1A5 B1B5 B1D5 B2A5 250/ / / / / 235 Same as -A1A5 except for short 2575/ /100LL 8.50:1 governor studs and two impulse magnetos 2575/ /100LL 8.50:1 Same as -A1A5 except for two impulse magnetos Same as -A1B5 except for two sixth 2575/ /100LL 8.50:1 order counterweights with Retard Breaker 2575/ / /100LL 8.50:1 Same as -A1B5 except for Retard Breaker 100/100LL 8.50: /100LL 8.50:1 250/ / / / A1A with short governor studs and locating bushing, relocate 60 deg counter clockwise Special Navy "Aztec", Same as -A1D5 except for provision for deicing and chrome barrels, 24 volt system std. Same as -A1A5 but with more 2575/ /100LL 8.50:1 effective counterweights for use with Hartzell "compact" Same as -A1B5 but with more 2575/ /100LL 8.50:1 effective counterweights for use with Hartzell "compact" Same as -A1C5 but with more 2575/ /100LL 8.50:1 effective counterweights for use with Hartzell "compact" Same as -A1D5 but with more 2575/ /100LL 8.50:1 effective counterweights for use with Hartzell "compact" :1 Same as -A1D5 but low C.R :1 Same as -B1A5 but with impulse coupling magnetos and a field conversion of A1A5, -A1B5, or - A1C5 to low compression :1 -B1A5 with series :1 Same as -B1A5 but does not have provision for controllable

28 B2B5 B2C5 B4A5 B4B5 D1A5 E4A5 E4B5 E4C5 FLA5 F1B5 G1A5 G2A5 H1A5 H1A5D H1B5D : : : : /100LL 8.50: /i00LL 8.50: /100LL 8.50: /100LL 8.50:1 Same as -B2A5 but with impulse coupling magnetos Same as -B2B5 but has series Same as -B1B5 but with more effective counterweights for use with Hartzell "compact" Same as rblb5 but with more effective counterweights for use with Hartzell "compact" Same as -A1D5 but with Bed-type mounts Same as -A4D5 except for higher speed and rating Same as -E4A5 but with impulse coupling magnetos with integral feedthru capacitors Same as -E4B5 but has series Same as -A~ except for special studs for front end mounting Same as -F1A5 except for new style crankcase and Retard Breaker Similar to -E4C5 except has stiffer crankshaft and -A1D5 counterweights Same as -G1A5 but does not have provision for controllable Similar to -G1A5 but has piston cooling oil jets and has -21 and -20 magnetos Same as -H1A5 but equipped with D6LN-3000 impulse coupling dual magneto system along with the dual magneto accessory housing and related drive system Same as -H1A5 but equipped with D6LN-3200 dual magneto system, dual magneto accessory housing, gear train and related drive system Same as -H1A5 but with fixed pitch

29 H2A5 H2A5D H2B5D J1A5D J1B5D J1C5D DD5D J2A5D J2B5D J2C5D J2D5D J3A5 J3A5D J3C5D L3C5D /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50:1 Same as -H2A5 but equipped with D6LN-3000 impulse coupling dual magneto system along with the dual magneto accessory housing and related drive system Same as -H2A5 but equipped with D6LN-3200 dual magneto system, dual magneto accessory housing, gear train and related drive system Similar to -A4A5 except for rating, speed, D6LN-3000 impulse coupling dual magneto and various items of weight reduction Same as -J~D but with D6LN-3200 retard breaker dual magnetos Same as -J1A5D but with rear mounted HA-6 horizontal carburetor Same as -J1C5D but with D6LN-3200 retard breaker dual magneto Same as -J1A5D but with fixed pitch Same as -J1B5D but with fixed pitch Same as -J1C5D but with fixed pitch Same as -J11)5D but with fixed pitch Same as -J~D but has Slick 6251 (impulse coupling) and 6250 magnetos Same as -J1A5D but has heavier counterweights for use with Hartzell extended hub controllable Same as -J1C5D but has heavier counterweights for use with McCauley controllable Similar to -J3C5D except for long reach spark plugs, high pressure fuel pump, piston cooling oil jet and turbocharger scavenge pump

30 A1A5 B1A5 B1B5 B1C5 C1B5 C1C5 C2C C4B5 C4C5 C4D5 C4D5D D4A5 D4B5 D4C5 E1A5 E1B5 E1C5 G1A5 G1B /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.50: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70:1 High compression tuned induction, Retard Breaker, Bendix fuel injector Same as -A1A5 except for updraft exhaust cooling Same as -B1A5 except for Sunmonds fuel injector Same as -B1A5 except it has external servo bleed in fuel injection system Same as A1D5 but with Bendix fuel injector Same as -C1B5 but has AN fuel pump drive Conversion of A2B to Bendix fuel injection and AN fuel pump drive Same as -C1B5 but with more effective counterweights for use with Hartzell "compact,, Same as -C4B5 but has AN fuel pump drive Same as -C4D5D except has two magnetos Same as -C4B5 but with D6LN-3000 impulse coupling magneto Same as E4A5 but with Bendix fuel injection Same as -D4A5 but has series impulse coupling magnetos Same as -D4B5 but with Retard Breaker Same as -B1C5 but with piston cooling oil jets Same as -E1A5 but with series Same as -E1B5 with RSA-10ED1 fuel injector Same as -A1A5 but with piston cooling oil jets Similar to -G1A5 but has series and RSA-10ED1 fuel

31 G1C5 G1D5 G1E5 G1F5 J4A5 K1A5 K1A5D K1B5 K1BSD K1C5 K1D5 K1E5 K1E5D K1F5 K1F5D K1G /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.50:1 300/ / 2575 injector Same as -G1B5 but has impulse magnetos and 38-1/2" injector adapter Same as -G1C5 but has straight injeecor inlet Same as -G1A5 but has series Same as -G1E5 but with (2) impulse coupling Same as -C4B5 except comersion for use with turbo- charger, long reach spark plugs, piston cooling oil jets, AN fuel pump drive, vented fuel nozzles and series Similar to -G1A5 but has series, RSA-10ED1 injector, large crankshaft and 38-1/2_ fuel injector adapter Same as -K1A5 but with D6LN-3000 impulse coupling dual magneto Similar to -KIA5 but has two impulse coupling magnetos and straight injector adapter Same as -K1B5 but with D6LN-3000 impulse coupling dual magneto 100/100LL 8.70:1 Similar to -G1A5 but has -K1A5 rotating system 300/ / 2575 Same as -K1A5 but has -200 series, flange fuel injector and straight injector inlet Similar to -K1C5 but has series impulse Same as -K1E5 but with D6LN-3000 impulse coupling dual magneto 100/100LL 8.70:1 Same as -G1B5 but with K series rotating system Same as -K1F5 but with D6LN-3200 retard breaker dual magneto Same as -K1A5 but has diaphragm type fuel pump and drive

32 K1G5D K1H5 KU5 KU5D K1K5 K2A5 L1A5 L1A5D L1B5D L1C5 M1A5 M1A5D M1B5D M1C5 M2A5D N1A5 P1A O0/100LL 8.70: /100LL 8.70:1 Same as -K1A5D but has diaphragm type fuel pump and drive Same as -K1B5 but has diaphragm type fuel pump and drive Same as -K1F5 but has diaphragm type fuel pump and drive Same as -K1F5D but has diaphragm type fuel pump and drive Similar to -K1A5 except modified for use with an Aerobatic kit Same as -K1A5 except has different bushings Similar to -K1A5 but with front air inlet and Retard Same as -L1A5 but with D6LN-3000 impulse coupling dual magneto Similar to -L1A5D except for a modified oil sump Same as -L1A5 but has diaphragm type fuel pump and drive Similar to -K1A5 but has Retard and up exhaust heads Same as -M1A5 but with D6LN-3200 Retard Breaker dual magneto Similar to -M1A5D but with RSA- 10ED1 fuel injector, automotive type fuel pump, D6LN-3000 impulse coupling magneto and straight fuel injection adapter Same as -M1A5 except has impulse magneto Similar to -M1A5 but has D6LN-3200 Retard Breaker dual magneto and provision for fixed pitch Similar to -D4A5 but with G1A5 crankcase and crankshaft and -K1A5 counterweight assembly Same as -G1B5 but has larger oil pump and is s usable for turbocharging

33 R1A5 S1A5 T4A5D T4B5 T4B5D T4C5D U1A5D U1B5D V4A5D W1A5 W1A5D W3A5D AA1A5 AA1B5 V A1A V A2A V B1A 300/ / 2575 Similar to -N1A5 except converted for use with turbocharger long reach spark plugs. Piston cooling oil jets, AN fuel pump, vented fuel nozzles and series magnetos 100/100LL 8.70:1 Same as -P1A5 but with K series rotating system /100LL 8.70: /100LL 8.70: /100LL 8.50: /100LL 8.50: /100LL 7.30: /100LL 7.30: : : :1 Similar to -D4B5 but has D6LN-3000 impulse coupling dual magneto and horizontal rear inlet fuel injector Same as -T4B5D except has two Slick Identical to -T4A5D except for fuel drain boss location Same as -T4B5D but has Bendix D6LN-3200 retard breaker magneto Same as -L1A5 but with up-exhaust cylinder heads and D6LN-3000 impulse coupling dual magneto Same as -U1A5D but has diaphragm type fuel pump and drive Same as -T4B5D except for front mounted fuel injector Same as -W1A5D except has two Slick Similar to J1A5D except that it is equipped with V4A5D sump, intake pipes and fuel injection system Same as -W1A5D but has heavier counterweights for use with Hartzell Similar to -S1A5 except for compression ratio Same as -AA1A5 except has impulse magneto and higher rating Low compression vertical PS-7BD carburetor Same as -A1A but with spring coupling accessory drive Same as -A1A except MA-6-AA carburetor

34 V B1B V B1B3 V B1C V B1D V B1E V B1F V B1H3 V B2A V B2C V B2D V B2E V B2G V C1A V C1B V C1C3 V C2A V C2B : : : : : : : : : : : : /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70:1 Same as -B1A except for Retard Breaker and less fuel pump drive and hydraulic pump drive Same as -BIB except for six 3rd order counterweights Same as -B1A except for Retard Breaker Same as -B1C except for two MA-6- AA carburetors Retrofit kit of -B1A with two MA-6-AA carburetors Same as -BIB but has fuel and hydraulic pump drives Same as -B1B3 but with series Same as -B1A but with spring coupling accessory drive Same as -B1C but with spr~ng coupling accessory drive Same as -BID but with sprmg coupling accessory drive Same as -B1E but with spring coupling accessory drive Same as -B2D but with series High compression altitude engine with two (2) MA-6-AA carburetors, retard breaker magnetos. Same as -B1D except for compression ratio and power Retrofit kit of -B1E with high compression piston and higher power Same as -B1B3 except it has high compression pistons and two MA-6- AA carburetors Same as -CIA but with spring coupling accessory drive Same as -C1B but with spring coupling accessory drive V /100LL 8.70:1 Same as -C2A except for series

35 C2C 9,-9A H A1A IG A1A IG A1B IG A1C IG B1A IG B1B IG B1C IV A1A T A1A T A1B T A1C T C1A T E1A T G1A magnetos /100LL 8.70:1 Military version of VC2A /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 8.70: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.20: /100LL 7.20:1 Similar to K1A5 but has lower rating and speed, no provision for governor and has front mounting pads machined and studded High compression tuned induction, Retard Breaker, Bendix fuel injector Same as -A1A except for low tension ignition system Similar to -A1A but equipped with RSA-10DB1 fuel injector, RG-9080-J7 fuel pump, S6RN-1208 and magnetos and a Prestolite 24V-100A AN drive alternator Same as -A1A except for updraft exhaust cooling Same as -B1A except for low tension ignition system Same as -BM except it has extemal sewo bleed in fuel injection system Similar to VC1A but has Bendix RS10-AD1 fuel injector Similar to ELA5 but has turbocharger (TE0659) RSA-10-AD1 fuel injector and series Same as -A1A but has density controller with faster temperature response Similar to -A1B but has revised controller setting J4A5 equipped with TE0659 turbocharger and low compression pistons Same as -CIA but has higher rating and impulse coupling magneto /100LL 8.50:1 Same as -CIA but high compression

36 T H1A T K1AD T S1AD T AA1AD T AB1AD T AB1BD T AF1A T A2A T A2B T A2C T F2BD T J2B /100LL 7.20: /100LL 8.00: /100LL 7.30: /100LL 8.00: /100LL 8.00: /100LL 8.00: /100LL 8.00: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30:1 Same as -ETA except for horsepower setting Similar to -CIA but with D6LN-3200 retard breaker dual magneto, pressure controller, provision for cabin pressurization, rear mounted fuel injector, turbocharger mounted to rear of engine and higher C.R. Similar to M2AD with front air inlet, provision for controllable, a manually controlled TE0659 turbocharger and D6LN-3000 impulse coupling magneto Similar to -K1AD but has a different controller system and has provision for a rear mounted governor Same as -AA1AD but has bottom mounted fuel injector, a relocated turbocharger and a D6LN-3000 impulse coupling magneto Similar to -AB1AD except has governor mounted on the accessory housing and the turbo scavenger pump moved to the vacuum pump pad and more effective counterweights for McCauley Similar to -AA1AD but has Slick magnetos, different turbocharger and an intercooler Same as -A1A but with flange bushings for 3-blade Same as -A1B but with flange bushings for 3-blade Same as -A1C but with flange bushings for 3-blade Similar to -A2B but incorporates D6LN-3200 retard breaker dual magneto system Same as -J2BD but has S6LN-1208 (Retard Breaker) and S6LN-1209 magnetos T /100LL 7.30:1 Similar to -F2BD except equipped with

37 J2BD T N2BD T R2AD T T2AD T U2A T V2AD T W2A T AE2A 540- D4A D4B D4C L1B L1B5D /100LL 7.30:1 350/ 340 TH08A60 turbocharger Identical to -J2BD except turbocharger shifted one-half inch to the left Similar to -J2BD except has provision 2575/ /100LL 7.30:1 for cabin bleed and has a variable pressure controller /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30:1 Same as -J2BD except for a modified exhaust transition and lower rating Similar to IO-~0-~5 but with intercooler and customer supplied turbocharger system Similar to -J2BD except with an intercooler and a change in cylinder head design Similar to -V2AD but with Slick 6261 (imp. coupling) and 6260 pressurized magnetos, a different controller system and without either induction air cooler or cabin bleed Similar to -U2A but has (2) Garrett instead of Roto-Master turbochargers, (2) intercoolers, (1) wastegate and Slick magnetos Same as D4A5 but is equipped with Aerobatic kit Same as D4B5 but is equipped with Aerobatic kit Same as D4C5 but is equipped with Aerobatic kit Same as -L1B5D but has Slick 6251 (impulse coupling) and 6250 magnetos Same as L1B5D but is equipped with Aerobatic kit Supercharged Bendix fuel injector, dry IGSO- 540-ALA /100LL 7.30:1 sump, cross-wise accessones high -50 altitude magnetos

38 Same as -AL: but with honzontal air IGSO- 540-A1C /100LL 7.30:1 inlet housing and has external servo bleed in fuel injection system IGSO- 540-A1D IGSO- 540-A1E IGSO- 540-A1F IGSO- 540-A1H /100LL 7.30:1 Same as -A1A but has series /100LL 7.30:1 Same as -A1C but has series and no vent flow restriction /100LL 7.30:1 Same as -AID but with fuel flow modulator removed /100LL 7.30:1 Same as -ATE but with fuel flow modulator removed Same as -ALA except for updraft IGSO- 540-BLA /100LL 7.30:1 exhaust cooling and Simmonds fuel injector IGSO- 540-B1C LTIO K1AD LTIO F2BD LTIO- 540-J2B LTIO J2BD LTIO N2BD LTIO R2AD LTIO- 540-U2A LTIO V2AD LTIO- 540-W2A /100LL 7.30:1 Same as -B1A but has series /100LL 8.00: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30:1 350/ / 2500 Similar to TK1AD but has left hand rotation crankshaft Same as TF2BD but has reverse rotation Same as -J2BD but have S6RN-1208 (Retard Breaker) and S6RN-12O9 magnetos Same as TJ2BD but has reverse rotation Similar to TN2BD but has left hand rotation crankshaft 100/100LL 7.30:1 Similar to TR2AD but has left hand rotation crankshaft /100LL 7.30:1 Same as TU2A but has reverse rotation /100LL 7.30:1 Same as TV2AD but has reverse rotation /100LL 7.30:1 Same as TW2A but has left hand rotation crankshaft

39 TIVO- 540-A2A Model TIO-541- A1A TIO-541- E TIO-541- E1B4 TIO-541- E1C4 TIO-541- E1D4 TIGO- 541-D1A /100LL 7.30:1 HP T/O RPM 14,000 feet at 3200 RPM, turbocharger Bendix fuel injection vertical helicopter engine with spring coupling accessory drive -57 Fuel C.R. DESCRIPTION Suffix /100LL 7.30: /100LL 730: /100LL 7.30: /100LL 7.30: /100LL 7.30: /100LL 7.30:1 Turbocharger (T-1823), fuel injected (RSA-10-ADV, crosswise accessories, integral accessory section, wet sump Similar to -A1A but has compressor drive, larger redesigned cylinder head, RSA-10DB1 injector and higher rating Same as -E~4 but has no provision for cabin pressurization Same as -E1A4 but has 1~1879 turbocharger Same as -E1B4 but has 1~1879 turbocharger Turbocharged (T18A21), fuel injected (RSA-l0-DBl), offset reduction gear, torquemeter, crosswise accessories, integral accessory section, wet sump Similar to -D1A but with integral TIGO- 541-D1B /100LL 7.30:1 wastegate turbocharger and low drag cylinder heads TIGO- 541-E1A TIGO GLAD /100LL 7.30:1 Same as -D1A except for rating /100LL 7.30:1 Similar to -D1A but has D6RN-3200 retard breaker dual magneto and intercooler and fuel head enrichment fuel injector PISTON - (8) EIGHT CYLINDER SERIES Model IO-720- A1A HP T/O RPM Fuel C.R. DESCRIPTION Suffix /100LL 8.70:1 High compression tuned induction, Bendix fuel injector and AN fuel pump drive IO /100LL 8.70:1 Same as -A~ but equipped with S8LN

LYCOMING CYLINDER PRICING

LYCOMING CYLINDER PRICING SHIPPING: 2415 EMBARCADERO WAY, PALO ALTO, CA 94303 MAILING: P.O. BOX 50608, PALO ALTO, CA. 94303-0608 Phone: 650-354-1399 Fax: 650-354-1395 LYCOMING CYLINDER PRICING CYLINDER PRICING ENGINE MODEL: O-235

More information

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA U.S.A. Tel Fax

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA U.S.A. Tel Fax 652 Oliver Street Williamsport, PA. 17701 U.S.A. Tel. 570 323 6181 Fax. 570 327 7101 www.lycoming.com SERVICE INSTRUCTION DATE: March 8, 2012 Service Instruction No. 1098H (Supersedes Service Instruction

More information

SERVICE INSTRUCTION. All Certified Lycoming direct drive engines. TIME OF COMPLIANCE: At owner s discretion.

SERVICE INSTRUCTION. All Certified Lycoming direct drive engines. TIME OF COMPLIANCE: At owner s discretion. 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

VACUUM PRESSURE PUMPS INSTALLATION CAUTIONS AND INFORMATION READ AND FOLLOW CAREFULLY!

VACUUM PRESSURE PUMPS INSTALLATION CAUTIONS AND INFORMATION READ AND FOLLOW CAREFULLY! F.A.A.-P.M.A. MODEL 1U128A AND 1U128B REVISION 17 February 21, 2002 VACUUM PRESSURE PUMPS INSTALLATION CAUTIONS AND INFORMATION READ AND FOLLOW CAREFULLY! The following information applies to all installations

More information

DATE: February 13, 2019 Service Instruction No. 1037V (Supersedes Service Instruction No. 1037U) Engineering Aspects are FAA Approved

DATE: February 13, 2019 Service Instruction No. 1037V (Supersedes Service Instruction No. 1037U) Engineering Aspects are FAA Approved 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

TYPE CERTIFICATE DATA SHEET NO. E14EA. Avco Corporation Williamsport, Pennsylvania 17701

TYPE CERTIFICATE DATA SHEET NO. E14EA. Avco Corporation Williamsport, Pennsylvania 17701 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION E14EA Revision 16 TEXTRON LYCOMING TIO-540-A1A, -A1B, -A2A, -A2B, -A1C, -A2C, -C1A, -E1A, -F2BD, -G1A, -H1A, -J2B, -J2BD, -K1AD, -N2BD, -R2AD,

More information

AERO ACCESSORIES, Inc.

AERO ACCESSORIES, Inc. www.tempestplus.com AERO ACCESSORIES, Inc. COVERS APPLICATIONS FOR FAA PMA APPROVED AVIATION SPARK PLUGS APPLICATION GUIDE ISSUED REVISED PAGES REVISION MO DAY YR MO DAY YR 06 21 10 00 00 00 1 of 10 Original

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 1E10 Revision No. 22 TEXTRON Lycoming IO-360-A1A, -A1B, -A1B6, -A1B6D, -A1C, -A1D, -A1D6, -A1D6D, -A2A, -A2B, -A2C, -A3B6,-A3B6D, -A3D6D, -B1A,

More information

SERVICE LETTER. Service Letter No. L114AN (Supersedes Service Letter No. L114AM) February 3, Owners and Operators of Lycoming Aircraft Engines

SERVICE LETTER. Service Letter No. L114AN (Supersedes Service Letter No. L114AM) February 3, Owners and Operators of Lycoming Aircraft Engines 652 Oliver Street Williamsport, PA. 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.textron.com SERVICE LETTER Service Letter No. L114AN (Supersedes Service Letter No. L114AM) February 3,

More information

7. Are you upgrading a complete engine from a TCM/ Bendix to a Slick system? If yes, purchase a complete Slick Ignition Upgrade Kit.

7. Are you upgrading a complete engine from a TCM/ Bendix to a Slick system? If yes, purchase a complete Slick Ignition Upgrade Kit. 1.1 PRODUCT APPLICATION INFORMATION WORKSEET The following information will aid you in selecting the correct magneto, upgrade kit, or ignition harness: 1. Engine Manufacturer 2. Engine Model Number 3.

More information

DATE: May 19, 2000 Service Instruction No. 1443E (Supersedes Service Instruction No. 1443D) Engineering Aspects are FAA Approved

DATE: May 19, 2000 Service Instruction No. 1443E (Supersedes Service Instruction No. 1443D) Engineering Aspects are FAA Approved DATE: May 19, 2000 (Supersedes Service Instruction No. 1443D) Engineering Aspects are FAA Approved SUBJECT: MODELS AFFECTED: TIME OF COMPLIANCE: Approved Slick Magnetos on Textron Lycoming Engines See

More information

MANDATORY SERVICE BULLETIN

MANDATORY SERVICE BULLETIN 652 Oliver Street Williamsport, PA 17701 U.S.A. Telephone +1 (800) 258-3279 (U.S. and Canada) Telephone +1 (570) 323-6181 (International) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

MOONEY INTERNATIONAL CORPORATION The Symbol of Performancet MOONEY SPECIAL LETTER Date:

MOONEY INTERNATIONAL CORPORATION The Symbol of Performancet MOONEY SPECIAL LETTER Date: MOONEY INTERNATIONAL CORPORATION The Symbol of Performancet MOONEY SPECIAL LETTER 15-24 Date: 11-19-2015 SUBJECT: MODELS/ S/N AFFECTED: To ADVISE MOONEY OWNERS/OPERATORS of the LYCOMING Service Instruction

More information

European Aviation Safety Agency

European Aviation Safety Agency European Aviation Safety Agency EASA TYPE-CERTIFICATE DATA SHEET Number: IM.E.032 Issue: 01 Date: 27 September 2012 Type: Lycoming Engines Models IO-360-A1A IO-360-C1B AEIO-360-A1E6 HIO-360-F1AD IO-360-A1B

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 1E12

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 1E12 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 1E12 1E12 Revision 9 Lycoming Engines IO-320 -A1A-A2A-B1A, -B1B, B1C, -B1E, -B1D, -B2A, -C1A, -C1B, -D1A, -D1C,

More information

P-920, Revision 32 Page 2 of 13

P-920, Revision 32 Page 2 of 13 DEPARTMENT OF TRANSPORTATION P-920 FEDERAL AVIATION ADMINISTRATION Revision 32 Hartzell HC-C2Y, BHC-C2Y, CHC-C2Y, DHC-C2Y TYPE CERTIFICATE DATA SHEET NO. P-920 March 9, 2010 Propellers of models described

More information

MANDATORY SERVICE BULLETIN

MANDATORY SERVICE BULLETIN 652 Oliver Street Williamsport, PA 17701 U.S.A. Telephone +1 (800) 258-3279 (U.S. and Canada) Telephone +1 (570) 323-6181 (International) Facsimile +1 (570) 327-7101 www.lycoming.com MANDATORY SERVICE

More information

Updated June Cylinder Application Charts

Updated June Cylinder Application Charts Updated June 2017 Cylinder Application Charts NIC3 CYLINDER COATING EXTENDED LIFE REDUCED WEAR NIC3 CYLINDERS BETTER PERFORMANCE Nickel silicon carbide is a chemical compound coating of nickel and silicon

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-223

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-223 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION E-223 Revision 18 Textron Lycoming O-233-A1,O-235 O-235-A,-B,-AP,-BP-C,-C1,-C1A,-C1B,-C1C,-C2A,-C2B,-C2C, -E1,-E1B,-E2A,-E2B,-F1,-F1B,-F2A,-F2B,-G1,-G1B,-G2A,-G2B,

More information

IO-360, AIO-360, HIO-360 & TIO-360 Series

IO-360, AIO-360, HIO-360 & TIO-360 Series Operator s Manual Lycoming O-360, HO-360, IO-360, AIO-360, HIO-360 & TIO-360 Series Approved by FAA 8 th Edition Part No. 60297-12 652 Oliver Street Williamsport, PA. 17701 U.S.A. 570/323-6181 October

More information

NOTE. In order to accommodate clearer type, larger charts and graphs, and more

NOTE. In order to accommodate clearer type, larger charts and graphs, and more NOTE In order to accommodate clearer type, larger charts and graphs, and more detailed illustrations, this edition of the O-360, HO-360, IO-360, AIO-360, HIO-360 and TIO-360 Operator s Manual, Lycoming

More information

Airworthiness Directive Schedule

Airworthiness Directive Schedule Airworthiness Directive Schedule Lycoming IO-720 Series Engines 25 October 2018 Notes: 1. This AD schedule is applicable to Lycoming IO-720 series engines manufactured under FAA Type Certificate Number

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-275. Avco Corporation Williamsport, Pennsylvania 17701

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-275. Avco Corporation Williamsport, Pennsylvania 17701 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-275 E-275 Revision 10 AVCO Lycoming GO-480, GO-480-A1A, -B, -B1, -B1A6, -B1B, -B1C, -B1D, -C1B6, -C1D6, -C2C6,

More information

Cylinder Application Chart

Cylinder Application Chart Cylinder Application Chart OEM Engine Model Cyl. Class New TITAN Cylinders Nickel Barrels TISN New TITAN Cylinders Steel Barrels TIST OEM P/N OEM P/N ECi FREEDOM Brand Remanufactured Cylinders Nickel (FRCN)

More information

DATE: February 24, 2014 Service Instruction No. 1009AW (Supersedes Service Instruction No. 1009AV) Engineering Aspects are FAA Approved

DATE: February 24, 2014 Service Instruction No. 1009AW (Supersedes Service Instruction No. 1009AV) Engineering Aspects are FAA Approved 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258 3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323 6181 (Direct) Facsimile +1 (570) 327 7101 www.lycoming.com SERVICE INSTRUCTION

More information

Oil Filter Application Guide

Oil Filter Application Guide Oil Filter Application Guide AEROSPATIALE (SOCATA) TB9 TAMPICO O-320-D2A AA48110-2 TB10 TOBAGO O-360-A1AD AA48110-2 TB20 TRINIDAD IO-540-C4D5D TB21 TRINIDAD TC TIO-540-AB1AD TB-30 AEIO-540-L1B5D AEROSTAR

More information

Airworthiness Directive Schedule

Airworthiness Directive Schedule Airworthiness Directive Schedule Lycoming AEIO-540 and IO-540 Series Engines 31 August 2017 Notes: 1. This AD schedule is applicable to Lycoming AEIO-540 and IO-540 series engines manufactured under FAA

More information

SERVICE INSTRUCTION. Lycoming engines that meet defined criteria herein. REASON FOR REVISION: Added IO-360-N and IO-390-C engine models

SERVICE INSTRUCTION. Lycoming engines that meet defined criteria herein. REASON FOR REVISION: Added IO-360-N and IO-390-C engine models 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 www.lycoming.com SERVICE INSTRUCTION

More information

Bendix Fuel Servo Engine Aircraft Fuel Servo Servo Model Application Parts List Model

Bendix Fuel Servo Engine Aircraft Fuel Servo Servo Model Application Parts List Model Cross Reference Bendix Fuel Servo Engine Aircraft Fuel Servo Servo Model Application Parts List Model AEIO-320-E1B BELLANCA AIRCRAFT CHAMPION 2524307-10 RSA-5AD1 AEIO-320-E2B BELLANCA DECATHLON 8K-CAB

More information

Airworthiness Directive Schedule

Airworthiness Directive Schedule Airworthiness Directive Schedule Lycoming O-540 Series Engines 25 October 2018 Notes: 1. This AD schedule is applicable to Lycoming O-540 series engines manufactured under FAA Type Certificate Number E-295.

More information

USE THE FIND FUNCTION TO FIND THE PART NUMBER ( THEY ARE NOT LISTED IN ORDER).

USE THE FIND FUNCTION TO FIND THE PART NUMBER ( THEY ARE NOT LISTED IN ORDER). USE THE FIND FUNCTION TO FIND THE PART NUMBER ( THEY ARE NOT LISTED IN ORDER). PART NUMBER DESCRIPTION INSTALLATION ELIGIBILITY ASC238445 PISTON RING PRATT & WHITNEY AIRCRAFT R1340 SERIES ASC238446 PISTON

More information

DATE: November 22, 2000 Service Bulletin No. 539A (Supersedes Service Bulletin No. 539 and Supplement No. 1) Engineering Aspects are FAA Approved

DATE: November 22, 2000 Service Bulletin No. 539A (Supersedes Service Bulletin No. 539 and Supplement No. 1) Engineering Aspects are FAA Approved DATE: November 22, 2000 (Supersedes Service Bulletin No. 539 and Supplement No. 1) Engineering Aspects are FAA Approved SUBJECT: MODELS AFFECTED: Reprint of Crane/Lear Romec Service Bulletins No. RG9080-73-001,

More information

Avco Lycoming Service Letter No. L218 and Service Instruction No. 1059C, No. 1110C and No. 1257E

Avco Lycoming Service Letter No. L218 and Service Instruction No. 1059C, No. 1110C and No. 1257E VSP-75 August 14, 1987 S/M VENDOR PUBLICATION TO: All Piper Distributors, Factory Direct Dealers and Piper Field Service Facilities Avco Lycoming Service Letter No. L18 and Service Instruction No. 1059C,

More information

DATE: May 8, 2012 Service Instruction No. 1279C (Supersedes Service Instruction No. 1279B) Engineering Aspects are FAA Approved

DATE: May 8, 2012 Service Instruction No. 1279C (Supersedes Service Instruction No. 1279B) Engineering Aspects are FAA Approved 652 Oliver Street Williamsport, PA. 17701 U.S.A. Tel. 570 323 6181 Fax. 570 327 7101 www.lycoming.com SERVICE INSTRUCTION DATE: May 8, 2012 Service Instruction No. 1279C (Supersedes Service Instruction

More information

IO-360, AIO-360, HIO-360 & TIO-360 Series

IO-360, AIO-360, HIO-360 & TIO-360 Series Operator s Manual Lycoming O-360, HO-360, IO-360, AIO-360, HIO-360 & TIO-360 Series Approved by FAA 8 th Edition Part No. 60297-12 652 Oliver Street Williamsport, PA. 17701 U.S.A. 570/323-6181 October

More information

Airworthiness Directive Schedule

Airworthiness Directive Schedule Airworthiness Directive Schedule 28 February 2019 Notes: 1. This AD schedule is applicable to Lycoming LTIO-540 and TIO-540 series engines manufactured under FAA Type Certificate Number E14EA. 2. The Federal

More information

SERVICE INSTRUCTION. ISSUED REVISED PAGE NO. REVISION MO DAY YEAR MO DAY YEAR 1 of 8 BB

SERVICE INSTRUCTION. ISSUED REVISED PAGE NO. REVISION MO DAY YEAR MO DAY YEAR 1 of 8 BB 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

O-540, IO-540 Series

O-540, IO-540 Series Operator s Manual Lycoming O-540, IO-540 Series Approved by FAA 4 th Edition Part No. 60297-10 652 Oliver Street Williamsport, PA. 17701 U.S.A. 570/323-6181 June 2006 O-540, IO-540 Series Operator s Manual

More information

Thread pitch can be 5/8-24 or 3/4-20

Thread pitch can be 5/8-24 or 3/4-20 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-228

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-228 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION O-435, -A, -A2 O-435-B (O-435-5) O-435-C (O-435-1) O-435-C1 (O-435-11) O-435-C2 (O-435-13) O-435-K O-435-K1 (O-435-4) E-228 Revision 16 AVCO

More information

REMOVAL AND INSTALLATION LABOR ALLOWANCE GUIDEBOOK FOR RECIPROCATING AIRCRAFT ENGINES

REMOVAL AND INSTALLATION LABOR ALLOWANCE GUIDEBOOK FOR RECIPROCATING AIRCRAFT ENGINES REMOVAL AND INSTALLATION LABOR ALLOWANCE GUIDEBOOK FOR RECIPROCATING AIRCRAFT ENGINES SSP-875 Revision May 2000 2000 by Textron Lycoming All Rights Reserved -INTRODUCTION- The labor hours shown in this

More information

SITRANS F flowmeters. SITRANS F O delta p - Primary differential pressure devices. Orifice plate with annular chambers. 4/358 Siemens FI

SITRANS F flowmeters. SITRANS F O delta p - Primary differential pressure devices. Orifice plate with annular chambers. 4/358 Siemens FI Application Dimensional drawings Suitable for non-corrosive and corrosive gases, vapors and liquids; permissible operating temperature -60 to +550 C. Design Two support rings with replaceable orifice disk

More information

Overhaul and repair procedures for the following Standard Cast Cylinder Stud Assemblies and Cylinder Valve Assemblies:

Overhaul and repair procedures for the following Standard Cast Cylinder Stud Assemblies and Cylinder Valve Assemblies: Technical Aspects are FAA Approved Number: L00-13 C Replace L00-13 B Date: 04/29/2005 Subject: Overhaul and repair procedures for the following Standard Cast Cylinder Stud Assemblies and Cylinder Valve

More information

Crankshaft Gear Retaining Bolt Replacement NOTE

Crankshaft Gear Retaining Bolt Replacement NOTE 652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.textron.com MANDATORY SERVICE BULLETIN DATE: September 30, 2002 Engineering Aspects of this Service Bulletin

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Aircraft Engines Parts Catalog TIO-540 Series Standard Cylinder Flange Crankcase Models Part No. PC-35-6 652 Oliver Street Williamsport, PA 770 Reciprocating Engine Division/ Subsidiary of Textron Inc.

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Aircraft Engines Parts Catalog TIO/LTIO-540-V2AD Wide Cylinder Flange Model Part No. PC-35-2 652 Oliver Street Williamsport, PA 770 Aircraft Engines Parts Catalog TIO/LTIO-540-V2AD Wide Cylinder Flange

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Lycoming Aircraft Engines Parts Catalog GO-480-B, -D and F6 Series Aircraft Engines Part No. PC-111 652 Oliver Street Williamsport, PA 17701 Lycoming Aircraft Engines Parts Catalog GO-480-B, -D and F6

More information

TECHNICAL PUBLICATION REVISION

TECHNICAL PUBLICATION REVISION Lycoming Textron Lycoming/Subsidiary of Textron Inc. 65 Oliver Street Williamsport, PA 770 U.S.A. 77/33-68 REVISION No. PC06--A TECHNICAL PUBLICATION REVISION ENGINE MODEL 0/LIO-360-C, -J, HIO, TIO, AEIO-360

More information

ROTARY SHAFT / OIL SEALS GASKETS LINER RINGS REPAIR KITS BONDED SEALS O RINGS. Automotive Seals VW BARNWELL THE SEAL OF APPROVAL

ROTARY SHAFT / OIL SEALS GASKETS LINER RINGS REPAIR KITS BONDED SEALS O RINGS. Automotive Seals VW BARNWELL THE SEAL OF APPROVAL ROTARY SHAFT / OIL SEALS GASKETS LINER RINGS REPAIR KITS BONDED SEALS O RINGS Automotive Seals VW BARNWELL THE SEAL OF APPROVAL QUALITY AND SERVICE GUARANTEED Total Sealing Solutions Founded in 1972, M

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-273

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E-273 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION E-273 Revision 36 CONTINENTAL O-470-A, -B, -E, -G, -H, -J, -K, -L, -M, -N, -P, -R, -S, -T, -U O-470-B-CI, -G-CI, K-CI, L-CI, M-CI (NOTE 6) IO-470-A,

More information

TYPE CERTIFICATE DATA SHEET NO. E1CE

TYPE CERTIFICATE DATA SHEET NO. E1CE DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION Revision 17 CONTINENTAL IO-360-A, -B, -C, -D, -E, -G, -H, -J, -K, -AB, AF, -DB, -GB,-HB, -JB, -KB, -ES TYPE CERTIFICATE DATA SHEET NO. January

More information

SERVICE INSTRUCTION.

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

INDEX. Service Bulletins. Letters and Instructions. SSP April 2018

INDEX. Service Bulletins. Letters and Instructions. SSP April 2018 Service Bulletins Letters and Instructions INDEX SSP-112-5 April 2018 652 Oliver Street Williamsport, PA 17701 U.S.A. Phone: Main Office U.S. and Canada Toll Free +1 (800) 258-3279 Direct +1 (570) 323-6181

More information

MANUAL OPERATOR'S REVISION Island Enterprises. 80 Operators Manual. are intended either to replace, add to, or delete

MANUAL OPERATOR'S REVISION Island Enterprises. 80 Operators Manual. are intended either to replace, add to, or delete OPERATOR'S REVISION MANUAL REVISION No. PUBLICATION PUBLICATION No. PUBLICATION DATE 60297-14-2 60297-14-2 GO, IGO, GSO, IGSO- 60297-14 July, 1973 80 Operators Manual The page(s) furnishedherewith pages

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 3E1

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 3E1 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. 3E1 3E1 Revision 26 CONTINENTAL IO-470-D, -E, -F, -G, -H, -J, -K, -L, -LO, -M, -N, -P, -R, -S, -T, -U, -V, -VO,

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Aircraft Engines Parts Catalog TIO/LTIO-540-UA Series Wide Cylinder Flange Model Part No. PC-35-65 Oliver Street Williamsport, PA 770 Aircraft Engines Parts Catalog TIO/LTIO-540-UA Series Wide Cylinder

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Lycoming Aircraft Engines Parts Catalog TIO-360-CA6D Wide Cylinder Flange Models Part No. PC-06-3 65 Oliver Street Williamsport, PA 770 Lycoming Aircraft Engines Parts Catalog TIO-360-CA6D Wide Cylinder

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Lycoming Aircraft Engines Parts Catalog AEIO-50-D Series -DA5, -DB5 Wide Cylinder Flange Crankcase Model Engines Part No. PC-5-5 Oliver Street Williamsport, PA 770 Textron Lycoming 5 Oliver Street Williamsport,

More information

SERVICE BULLETIN MANDATORY

SERVICE BULLETIN MANDATORY 652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.com MANDATORY SERVICE BULLETIN DATE: July 20, 2007 Service Bulletin No. 574A (Supersedes Service Bulletin

More information

Supplement No. 1. Service Bulletin No Crankshaft Replacement in Lycoming Engines

Supplement No. 1. Service Bulletin No Crankshaft Replacement in Lycoming Engines 652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.textron.com MANDATORY SERVICE BULLETIN November 30, 2005 Supplement No. 1 To Service Bulletin No. 566 SUBJECT:

More information

Direct solenoid and solenoid pilot operated valves

Direct solenoid and solenoid pilot operated valves Direct solenoid and solenoid pilot operated valves Individual mounting Series Inline Sub-base non plug-in 4 6 Air return Manual operator Solenoid 4-way pilot with balanced poppet Bonded spool 2 7 8 2 67

More information

INSTRUMENT PANEL CLUSTERS

INSTRUMENT PANEL CLUSTERS INSTRUMENT PANEL CLUSTERS NOT BUYING AT THIS TIME REVISED ##### PART # MAKE APPLICATION 6/18/2018 PRICE 56045618 CHRY IPC 40.00 56045679 CHRY IPC 40.00 56051103 CHRY IPC 40.00 56049833 AC,AD CHRY IPC 40.00

More information

Lycoming AIRCRAFT ENGINES. IO-540-AC1A5 Wide Series Flange Crankcase Model Engine PARTS CATALOG PC

Lycoming AIRCRAFT ENGINES. IO-540-AC1A5 Wide Series Flange Crankcase Model Engine PARTS CATALOG PC AIRCRAFT ENGINES IO-540-ACA5 Wide Series Flange Crankcase Model Engine PARTS CATALOG PC-5- November 008 Lycoming 5 Oliver Street Williamsport, PA 770 U.S.A. 570/33-8 IO-540-ACA5 PARTS CATALOG This illustrated

More information

SERVICE INSTRUCTION.

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA. 17701 U.S.A. Telephone +1 (800) 258-3279 U.S. and Canada (Toll Free) Telephone +1 (570) 323-6181 (Direct) Facsimile +1 (570) 327-7101 Email Technicalsupport@lycoming.com

More information

TECHNICAL PUBLICATION REVISION

TECHNICAL PUBLICATION REVISION Reciprocating Engine Division/ Subsidiary of Textron Inc. 65 Oliver Street Williamsport, PA 770 U.S.A. 77/33-68 TECHNICAL PUBLICATION REVISION REVISION No. PUBLICATION PUBLICATION No. PUBLICATION DATE

More information

O-540-A4B5 PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES

O-540-A4B5 PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES INTRODUCTION This illustrated parts catalog contains a complete parts listing for the Lycoming O-540-A4B5 wide cylinder flange crankcase model aircraft engines. Major assembly and sub-assembly parts of

More information

LYCOMING A Textron Company

LYCOMING A Textron Company LYCOMING AEIO-360-HB PARTS CATALOG This illustrated parts catalog contains a complete parts listing for the Lycoming AEIO-360-HB wide cylinder flange crankcase model aircraft engines. Major assembly and

More information

PUBLICATION REVISION

PUBLICATION REVISION Lycomlng 65 Oliver Street Williamsport, PA 770 U.S.A. 77/-6 TECHNICAL PUBLICATION REVISION REVISIOI No. PUBLICATION PUBLICATION No. PUBLICATION DATE IO-60-LA PC-06-A Engines PC-06- MAY, 996 This page(s)

More information

SERVICE BULLETIN MANDATORY

SERVICE BULLETIN MANDATORY 652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570 323 6181 Fax. 570 327 7101 www.lycoming.com MANDATORY SERVICE BULLETIN DATE: April 27, 2011 Service Bulletin No. 596 Engineering Aspects are FAA

More information

Heavy Duty Actuators CONTROLS. Pneumatic Actuators for Quarter-Turn Valves and Dampers Torques to 1,600,000 in. lbs. Double Acting and Spring Return

Heavy Duty Actuators CONTROLS. Pneumatic Actuators for Quarter-Turn Valves and Dampers Torques to 1,600,000 in. lbs. Double Acting and Spring Return CONTROLS Division of A-T Controls Heavy Duty Actuators Pneumatic Actuators for Quarter-Turn Valves and Dampers Torques to,600,000 in. lbs. Double Acting and Spring Return THD S E R I E S The Triac line

More information

Page No. 1 of 6 Date: April 29, 2011 Installation Eligibility: Model. PMA NUMBER PQ2724CE Part No. Model No.

Page No. 1 of 6 Date: April 29, 2011 Installation Eligibility: Model. PMA NUMBER PQ2724CE Part No. Model No. PMA NUMBER No. FAA Approval Basis and Approved Design Data Eligibility: Make Page No. 1 of 6 Propeller ATG210760 Woodward G210760 P210452( ), 210685, Test Report and Alexandria 17-30, 17-30A (IO-520 only)

More information

TECHNICAL PUBLICATION SUPPLEMENT

TECHNICAL PUBLICATION SUPPLEMENT TEXTRON Lycoming TECHNICAL PUBLICATION SUPPLEMENT SUPPLEMENT No. ENGINE MODEL PUBLICATION No. PUBLICATION DATE PC-0--B O-90-D Series PC-0- January 9 This supplement is arranged in the same basic format

More information

O-360 & IO-360 Series Model Specification Summary

O-360 & IO-360 Series Model Specification Summary O-360 & IO-360 Series Model Specification Summary 621 South Royal Lane, Suite 100 / Coppell, TX 75019 / 800-277-5168 www.superior-air-parts.com Technical Data Summary Design Highlights O-360 IO-360 Rating

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Aircraft Engines Parts Catalog IO-0-BG Wide Cylinder Flange Crankcase Model Engine Part No. PC-0- Oliver Street Williamsport, PA 770 Aircraft Engines Parts Catalog IO-0-BG Wide Cylinder Flange Crankcase

More information

S: With magnet. Bore x stroke (basic type) Cushion P: pneumatic adjustable

S: With magnet. Bore x stroke (basic type) Cushion P: pneumatic adjustable series MK Standard cylinders according to ISO 15552 How to order? M K A P S 50 x 100 M: Marani A: Double acting S: With magnet Bore x stroke (basic type) K: According to ISO 15552, Mickey-mouse type Cushion

More information

Kelly Aerospace, Inc.* Starter Eligibility Listing

Kelly Aerospace, Inc.* Starter Eligibility Listing Thermal Systems Power Systems 1625 Lost Nation Road 2900 Selma Highway Willoughby, OH 44094 Montgomery, AL 36108 (440) 951-4744 (334) 386-5400 www.kellyaerospace.com Service Information Letter The technical

More information

SERVICE INSTRUCTION. All Lycoming aircraft engine models

SERVICE INSTRUCTION. All Lycoming aircraft engine models 652 Oliver Street Williamspt, PA. 17701 U.S.A. Tel. 570 323 6181 Fax. 570 327 7101 www.lycoming.com SERVICE INSTRUCTION DATE: April 16, 2012 Service Instruction No. 1070R (Supersedes Service Instruction

More information

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E3SO. P.O. Box 90 Mobile, Alabama 36601

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. E3SO. P.O. Box 90 Mobile, Alabama 36601 DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE DATA SHEET NO. Revision 6 Continental IO-550-A, -B, -C,-D, -E, -F, -G, -L, -N -P, -R March 3, 2000 Engines of models described

More information

European Aviation Safety Agency

European Aviation Safety Agency European Aviation Safety Agency EASA TYPE-CERTIFICATE DATA SHEET Number : IM.E.027 Issue : 02 Date : 06 May 2008 Type : Lycoming IO-580 series engines Variants Lycoming IO-580-B1A Lycoming AEIO-580-B1A

More information

Frequently Asked Questions Certification 1. Are the ACS-320, ACS-360 and ACS-361 (ACS) Engines new zero time engines?

Frequently Asked Questions Certification 1. Are the ACS-320, ACS-360 and ACS-361 (ACS) Engines new zero time engines? Frequently Asked Questions Certification 1. Are the ACS-320, ACS-360 and ACS-361 (ACS) Engines new zero time engines? Yes. The ACS Engines are brand new, zero time engines designed to meet the increasing

More information

TEXTRON Lycoming AIRCRAFT ENGINES

TEXTRON Lycoming AIRCRAFT ENGINES TEXTRON Lycoming AIRCRAFT ENGINES O-60-AP Wide Cylinder Flange Crankcase Model Engines PARTS CATALOG PC-06-6 MARCH 99 0-60-AP PARTS CATALOG This illustrated parts catalog contains a complete parts listing

More information

LYCOMING MODEL SERIES AIRCRAFT ENGINES TABLE OF CONTENTS INTRODUCTION iii. INSTRUCTIONS FOR ORDERING PARTS.. ILLUSTRATED PARTS SECTION..

LYCOMING MODEL SERIES AIRCRAFT ENGINES TABLE OF CONTENTS INTRODUCTION iii. INSTRUCTIONS FOR ORDERING PARTS.. ILLUSTRATED PARTS SECTION.. TEXTRON Lycoming AIRCRAFT ENGINES O-30 Model Aircraft Engine PARTS CATALOG LYCOMING MODEL 0-30 SERIES AIRCRAFT ENGINES TABLE OF CONTENTS INTRODUCTION....................... iii. INSTRUCTIONS FOR ORDERING

More information

New, Rebuilt, Overhaul

New, Rebuilt, Overhaul Aftermarket Engine Price List New, Rebuilt, Overhaul AVAILABLE FROM AUTHORIZED TEXTRON LYCOMING DISTRIBUTORS Effective November 2001 (All prices subject to change without notice) SSP-SO~P LIS:Ci~: ILycoming

More information

O-540-F1B5 SERIES PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES

O-540-F1B5 SERIES PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES INTRODUCTION This illustrated parts catalog contains a complete parts listing for the Lycoming O-540-F1B5 series wide cylinder flange crankcase model aircraft engines. Major assembly and sub-assembly parts

More information

Vehicle Technical Specifications

Vehicle Technical Specifications Vehicle Manufacturer: Year and Model: Dodge (2003-2007) Viper Competition Coupe This specifications form was developed by SCCA Pro Racing and will be used by the TECHNICAL MANAGER to establish technical

More information

TYPE-CERTIFICATE DATA SHEET

TYPE-CERTIFICATE DATA SHEET TYPE-CERTIFICATE DATA SHEET For Models: IO-390-A1A6 IO-390-A3A6 IO-390-A1B6 IO-390-A3B6 AEIO-390-A1A6 AEIO-390-A3A6 AEIO-390-A1B6 AEIO-390-A3B6 IO-390-C1A6 IO-390-C3A6 IO-390-C1B6 IO-390-C3B6 No. IM.E.097

More information

SUPPLEMENT TO NO. 105

SUPPLEMENT TO NO. 105 SUPPLEMENT TO Model 0-30 Series Aircraft Engines Parts Catalog NO. 05 This supplement is provided to inform users of Lycoming parts catalogs of changes, deletions, additions and supersedures that have

More information

Vehicle Technical Specification Vehicle: Dodge Viper Competition Coupe 8.3LHybrid Class: GT

Vehicle Technical Specification Vehicle: Dodge Viper Competition Coupe 8.3LHybrid Class: GT Vehicle Manufacturer: Dodge Year and Model: (200-2007) Viper Competition Coupe Hybrid 8.L This specifications form was developed by SCCA Pro Racing and will be used by the TECHNCIAL MANAGER to establish

More information

MAC VALVES, INC. Rev. T

MAC VALVES, INC. Rev. T REVISION LEVEL DATE RELEASED CHANGE DESCRIPTION ECN NUMBER P.E. APPROVAL P.D APPROVAL A 5-11-95 ENGINEERING RELEASE 12727 EPJ B 1-15-96 ADDED 35 SERIES 13228 EPJ ADDED MOD 2938 TO 6500 SERIES, MODS 2910

More information

TEXTRON Lycoming AIRCRAFT ENGINES

TEXTRON Lycoming AIRCRAFT ENGINES TEXTRON Lycoming AIRCRAFT ENGINES O-60-CF & -CP Wide Cylinder Flange Crankcase Model Engines PARTS CATALOG PC-06- OCTOBER 995 65 Oliver Street Williamsport, PA 770 U.S.A. 77/-6 Lycoming O-60-CF &-CP PARTS

More information

********NOTICE********

********NOTICE******** IO-540-K1A5 Series Illustrated Parts Catalog February 2015 ********NOTICE******** This parts catalog, PC-615-K1A5 Series (models IO-540-K1A5, IO-540-K1A5D) supersedes the previous IO-540-K1A5, IO-540-K1A5D

More information

IO-540-K1H5 Series Illustrated Parts Catalog

IO-540-K1H5 Series Illustrated Parts Catalog IO-50-KH5 Series Illustrated Parts Catalog November 983 Engine model IO-50-KK5, previously covered in this parts catalog, has been superseded by PC-5-KK5. PC-5-03 5 Oliver Street Williamsport, PA 770 IO-50-KH5

More information

SITRANS F flowmeters. SITRANS F O delta p - Primary differential pressure devices Metering pipe with orifice plate and annular chambers 4/369

SITRANS F flowmeters. SITRANS F O delta p - Primary differential pressure devices Metering pipe with orifice plate and annular chambers 4/369 and annular chambers Application Suitable for non-corrosive and corrosive gases, vapors and liquids; permissible operating temperature -10 to +00 C. Design Orifice plate with annular chambers consisting

More information

Airworthiness Directive

Airworthiness Directive Airworthiness Directive Federal Register Information Header Information DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [62 FR 40262 NO. 144 07/28/97] [Docket No. 97-ANE-26-AD;

More information

Stars or starlets? Competitor overview switching devices. Only for internal use. sirius IN COMPARISON

Stars or starlets? Competitor overview switching devices. Only for internal use. sirius IN COMPARISON Only for internal use Stars or starlets? Competitor overview switching devices sirius IN COMPARISON Who are the real stars? The comparison. Under ideal conditions, the human eye can make-out approximately

More information

Orifice flowmeter F O N4

Orifice flowmeter F O N4 Special features Suitable for any mounting positions without reduction in accuracy Complies with requirements for treatment and disinfection of swimming/ bathing pools (DIN 9 643) Simple installation Direct

More information

The Product Range. Technical Data

The Product Range. Technical Data The Product Range Section 3.1 - Basic Cylinder Bore sizes (mm): 10, 16, 25, 32, 40, 50 The basic cylinder series satisfies the support and guidance requirements of a great diversity of applications. Various

More information

Protection Equipment. 5/2 Introduction

Protection Equipment. 5/2 Introduction Protection Equipment /2 Introduction SIRIUS 3RV2 Motor Starter Protectors/ Circuit Breakers up to 40 A /6 General data /12 For motor protection /14 For motor protection with overload relay function /1

More information

EM Sheet 01 TYPE CERTIFICATE DATA SHEET Nº EM-9105

EM Sheet 01 TYPE CERTIFICATE DATA SHEET Nº EM-9105 TYPE CERTIFICATE DATA SHEET Nº EM-9105 Type Certificate Holder: TELEDYNE CONTINENTAL MOTORS 2039 Broad Street Mobile, Alabama, 36601 U.S.A EM-9105-01 Sheet 01 TELEDYNE CONTINENTAL O-200-A, O-200-D 23 September

More information

Lycoming Aircraft Engines Parts Catalog

Lycoming Aircraft Engines Parts Catalog Lycoming Aircraft Engines Parts Catalog 76 Series O-360, LO-360 Series Part No. PC-3 65 Oliver Street Williamsport, PA 770 Lycoming Aircraft Engines Parts Catalog 76 Series O-360, LO-360 Series Part No.

More information