EZ-Haul Utility Wagon w/ Trailer Hitch

Transcription

1 EZ-Haul Utility Wagon w/ Trailer Hitch FarmTek All Rights Reserved. Reproduction is prohibited without permission. Revision date: STK# Description Utility Wagon 1

2 CARE AND MAINTENANCE Periodically check all fasteners to assure they are tight. Clean the wagon using water and mild soap. Rinse with water. Check the tire pressure and adjust to recommended pressure if needed. YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE Wagon. Thank you for purchasing this wagon. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the wagon. Please read these instructions before you begin. If you have any questions during the assembly, contact Customer Service for assistance. SAFETY PRECAUTIONS Do not use the wagon if any part is broken or damaged. This wagon is not a toy. Do not allow children use the wagon. Do not use on inclines; wagon may tip or roll away. Do not load your wagon with more than 1500 lbs. Inflate the tires with air only. Inflate the tires to the proper level as indicated on the tires. Do not inflate tires more than 35 PSI. Never use a flammable gas to inflate the tires. Never allow riders on the wagon. Always distribute payload evenly over the surface of the wagon bed (if equipped). REQUIRED TOOLS The following list identifies the main tools needed for assembly. To safely assemble the wagon, two (2) individuals are needed. Flathead screwdriver Metric and standard wrenches and/or ratchet and socket set Pliers UNPACK AND IDENTIFY PARTS The following steps help to ensure that you have all the necessary parts before you begin. Unpack the contents of the shipment and place where you can easily inventory the parts. If anything is missing or you have questions, consult the Pictorial Parts List or contact Customer Service. 2 Revision date:

3 To better align the wagon components, do not fully tighten the nuts and bolts until the entire wagon is assembled FRONT AND REAR AXLE ASSEMBLY Remove tongue bolt, locknut, tongue washers, and spacer from the center of the front axle. Align the hole in the center of the tongue yoke with the hole in the center of the front axle. Insert spacer between the tongue yoke and the axle frame. Secure using tongue bolt, tongue washers, small washer, and locknut. Slide one (1) wheel, large washer, and cotter pin in that order onto each end of the axle. Bend cotter pin to secure. Large Washer View as seen from the bottom. Cotter Pin Washer and cotter pin are used on the outside of the wheel. Install the wheel with the valve stem to the outside. Parts List and Tools Required Flat Screwdriver Back Axle (1) Socket/Wrench Set Large Washers (4) Front Axle (1) Pliers Wheels (4) Cotter Pins (4) Revision date:

4 2 CONNECT AXLES AND ATTACH TONGUE NOTE: Hardware may ship attached to parts. Position front and back axles as shown and insert the frame adaptor into the slots in both axles. Align the holes and secure using 12x70mm bolts, washers and locknuts. See diagram A. Front Axle 12x70mm bolts, washers,and locknuts Back Axle 3. Align the holes in the tongue with the holes in the tongue yoke. Secure in place using a 12x80mm bolt, washer, and locknut. See diagram B. Insert the hitch pin through the hitch end of the tongue and secure with cotter key. A Frame Adaptor 4. Tighten all connections. Periodically check connections to make sure they are tight and secure. 5. Check tire pressure and adjust as needed. Do not inflate tires more than 35 p.s.i. Tongue Yoke B Tongue Slide tongue end into tongue yoke and secure using bolt, washer, and locknut. Parts List and Tools Required Flat Screwdriver Frame Adaptor (1) Hitch Pin (1) 12x70mm Bolts (2) Socket/Wrench Set Tongue (1) Pliers Cotter Key (1) 12mm Washers (3) 12mm Locknuts (3) 12x80mm Bolt (1) 4 Revision date:

5 Space below is reserved for customer notes. Revision date: