Attention! The following must be done to maintain consistent staging with all Tranz Brake Valve Bodies for Three (3) Speed Automatics: Before
|
|
- Vanessa Bradley
- 5 years ago
- Views:
Transcription
1 Attention! The following must be done to maintain consistent staging with all Tranz Brake Valve Bodies for Three (3) Speed Automatics: Before turning bottom final stage yellow light on, you should be at a minimum of 1500 rpm to 2000 rpm. It also helps to engage the tranz brake switch once before you begin to roll into the final stage light. If you do this, in the late rounds when the transmission is hot, it will have less tendency to roll in deep. Remember you must push the Tranz Brake button then release the foot brake. If you do both at the same time, your car will vary on the way it locks down, causing erratic reaction times. Transmission must be full! Deep pans still must maintain natural full on dip stick! Caution : Due to Higher Line Pressure some units will blow Rear Clutch Piston Seal or bend the piston return spring. The following should cure that problem. Drill 1/16 Hole Rear Clutch Piston Ball Check Part #17899XA Page #1
2 1535 Owens Road, Jacksonville, FL (904) FAX (904) CHEETAH XtremeActionTranz Brake Valve Body (PRN123) (Positively Not For Street Use) Fits Torqueflite 727 & (Non Lock-Up) Part #17899XA (PRN123) The Turbo Action CHEETAH XtremeAction Tranz Brake gives you clean and positive shifts that you have come to expect from a CHEETAH Valve Body. In addition, you now have a Tranz Brake which will allow you to compete easily with or without a delay box. Special features include: Roller clutch protection due to a timed delay on the rear band release; Tranz Brake works in first gear only; no extra horsepower loss due to high line pressures; exclusive Power Lock brake system circuitry; quick release; high reliability; low current draw and easy installation (no internal modifications required). Deep Oil Pan Required w/proper pick-up (Must be single hole pick-up). Options that should be considered: 1. If 727, suggest #17090 springs for front clutch piston. 2. If 727 & 904, suggest 3.8 Kickdown Lever. 3. If 904, be sure that 904 transmission core is a 1971 or newer. Part Number will be 35XXXXX or higher. The following are the proper settings for your bands and clutches: Front Band & 904 : Adjust front band per the following specs - (a) Locate the adjustment on the driver side on the outside of the transmission, just ahead of the linkage. (b) You will need a 3/4 wrench and an open end 5/16 wrench. Break the locknut loose (3/4 nut). Now holding the locknut, turn the square lug in the center of the locknut with your 5/16 open end wrench. Turn wrench clockwise until wrench becomes snug (10 in./lbs.). Make sure the locknut doesn t move while tightening the square lug. (c) Now carefully turn 5/16 wrench counterclockwise 1 1/2 turns. Holding the 5/16 wrench, tighten the 3/4 wrench to 35 ft./lbs. (Very Tight). DO NOT allow the square lug to move while tightening the 3/4 locknut. Rear Band 727 : Rear Band 904 : Tighten adjustment lug 10 in./lbs., back off 2 turns and tighten locknut. Tighten adjustment lug 10 in./lbs., back off 4 turns and tighten locknut UP CORES ONLY. Front Clutch 727 & 904 : Four Clutches - Clearance = Five Clutches - Clearance = Rear Clutch 727 & 904 : Four Clutches - Clearance = Part #17899XA Page #2
3 Special characteristics about your CHEETAH XtremeAction Tranz Brake Valve Body: 1. First Gear - no gear braking. 2. First to second shift on jackstands will not be noticeable. 3. Line pressure can be read at the middle plug on passenger s side. Suggest a 200. PSI gauge, our Part # Positively Do Not make any modifications other then those suggested in these instructions. See page #10 for additional info for Pro Light Racing. CAUTION: Do Not Neutral Transmission till under 2500 RPM. Very Important!! You must use a single hole type filter with this valve body. Deep pan: Must be a single hole pick-up. Installation Instructions FIRST, READ INSTRUCTIONS CAREFULLY, THEN PROCEED TO INSTALL VALVE BODY PER THESE INSTRUCTIONS. Kit Includes: XA Valve Body Solenoid (Installed on Valve Body) Case Connector (Modified) 1 - U00781 Wire Snap Plug Connector Wire Restraint /16 Drill w/1/4 Shank /4 Pipe Tap C Pan Gasket C Pan Gasket Dacron Filter Single Hole Note: Must use single hole filter Filter Gasket (Use with deep pan filter extension) A ACC. Piston Blocker Rear Servo Shim STEP #1: If vehicle is on the ground, secure so it will not roll, (Preferably, vehicle should have all four wheels off the ground.) Place vehicle shift selector in park range. Remove throttle pressure linkage and gear selector linkage located on the driver s side of the vehicle. Disconnect only at the shaft coming out of the transmission case. You will note the two linkage levers on the shaft are fastened by a bolt in each case. Loosen these bolts completely. After loosening bolts, carefully pry levers upward with a screwdriver. The top throttle pressure lever is no longer needed. Part #17899XA Page #3
4 STEP #2: Remove all pan bolts but two on one end. This way you will be able to drain the transmission without getting soaked with oil. These two bolts can be gradually loosened off after most of the oil has been drained. STEP #3: Carefully remove the ten 7/16 bolts which hold the valve body in place. *Slowly pull valve body out of transmission, noting the hole that the long swinging rod came out of. The rod controls your car s park function. Most Torqueflites will have a large spring between one end of the valve body and the case. This spring should not be put back in the vehicle when using this valve body. *May be necessary to turn drive shaft to release long swinging rod. STEP #4: The transmission valve body is a very intricate piece of your transmission and therefore care should be taken to keeping it clean while working on it. Lay old valve body on a bench or table so that the swinging rod is laying towards you. Remove small clip that holds the swinging rod in place. Install this swinging rod on the new valve body. Secure by reinstalling clip. This swinging rod should fit the same as it did on the old valve body. STEP #5: Remove the three screws that hold the old filter on the old valve body. If installing deep pan, follow instructions for pickup installation. Install new filter #17013 directly against deep pan pickup. Install the thick gasket supplied between the valve body and deep pan pick-up. Note: Be sure the deep pan pick-up has only one hole. If you replace filter in the future, be sure it has only one pickup hole. STEP #6: If transmission is out of the vehicle, the governor valves can be removed. STEP #7: Cut out the templet, Fig. #1. Mark spot to be drilled with a small punch. Drill small 1/8 pilot hole. Then take #00690 special 7/16 drill and drill hole in case as shown in Fig. #2. STEP #8: Using #00691 special 1/4 pipe tap, tap the case till the case connector will just show through inside the case, Fig. #3. STEP #9: Install #17394 case connector into case. STEP #10: Remove accumulator piston by pulling down the middle piston from the passenger side of the transmission, Fig. #6. Some units have a spring on top, some on bottom of piston and some none at all. Install #17131A ACC. piston blocker between case and piston. CAUTION: Be sure piston is below surface enough to install valve body and not hit piston. If rod is too long, cut or grind small amount off and recheck. Also, leave out spring if it had one. SPECIAL NOTE If your transmission has part #35XXXXX or higher stamped on driver s side, just under shift linkage near pan rail, you have a 1971 or newer transmission. If you have a 1971 or newer, YOU MUST check under the accumulator to see if anyone has ever drilled a 3/16 hole in the upper small bore, Fig. #6. If your unit has the hole and has the 34XXXXX or higher, you must then plug the hole with a 1/4-20 set screw. If unit is a 1970 or older part #34XXXXX or lower you do not have to plug hole. Part #17899XA , Page #4
5 The following steps must be done for best brake action, both locking and releasing: If 727, proceed with STEP #11. If 904, remove tail housing and band lever pin, then proceed. STEP #11: Loosen lock nut on reverse band linkage and back off adjustment at least 6-8 turns, Fig. #7. If 904, slide lever out of the way. STEP #12: STEP #13: With a Scribe Hook, lift up on band strut and remove (727 Only). Now with screwdriver remove snap ring that retains spring retainer on rear servo. CAUTION: This section is under spring pressure. Be sure to secure with hand. Remove piston, spring, retainer and snap ring. (Fig. #8) STEP #14: Remove plug spring and install shim, Fig. #8. STEP #15: STEP #16: STEP #17: STEP #18: STEP #19: STEP #20: STEP #21: Reinstall servo piston, spring, retainer and snap ring. Be sure snap ring is in groove all the way. Carefully place strut back into position. It must be seated properly (727 Only). If 904, slide lever in place and install pin. Reinstall tail housing. Re-adjust rear band. If 727, turn in adjustment finger tight (10 in./lbs.), back off two (2) turns and then holding adjustment, lock the locknut. If 904, install tail housing, band lever pin and then adjust band to four (4) turns. Before re-installing valve body into transmission, take note of the plastic half ball shaped neutral-switch on the driver s side of the transmission inside of the transmission case. When installing the valve body, make sure this ball does not get damaged. Either remove the switch or merely slide the valve body carefully over the ball. The ball will retract as the valve body puts pressure on it. Also, do not install large spring which was between valve body and case. Carefully connect solenoid wire to case connector. Make sure wire connection does not get close to the park rod or the valve body and short out, Fig. #4. Place valve body back into transmission pushing the rod into hole that was mentioned in STEP #3. The rod should be angled towards the center of the transmission in the front. Push rod firmly towards rear while turning drive shaft. BUT DO NOT FORCE ROD OR VALVE BODY. With valve body in place, install 10 valve body bolts and tighten to 8-10 ft./lbs. Note position of #17390 wire restraint, Fig. #5. STEP #22: Adjust front band at this time (see instructions page #1). STEP #23: Clean pan and install with a new gasket. STEP #24: Replace shift linkage (large piece) and tighten bolt. Adjust linkage to be sure that shifter is selecting all gears properly. Especially critical is the 2 to 3 shift adjustment. CAUTION: This unit is PRN123. Part #17899XA Page #5
6 STEP #25: STEP #26: STEP #27: STEP #28: CAUTION: Remove all kickdown linkage from carburetor down to the transmission. Connect a #16 wire to the #17394 wire snap plug connector and connect it to case connector. Run the other end of the wire to delay box or direct to a quality momentary switch such as the Turbo Action #00774 switch on a special stretch cord for mounting on the steering wheel. Now run a 12 Volt supply to the switch. Check at transmission to be sure you have 12 Volts. NOTE: Sometimes you cannot hear solenoid so check with a test light or volt meter. (Fig. #1A) Refill transmission with a good type F ATF or Dexron Mercon fluid. It will usually take about 5 quarts of oil. DO NOT OVERFILL! Warm transmission up, select all gears, and then recheck oil level. Always check level of transmission fluid when in neutral, but put parking brake on as a safety measure or have someone hold foot brake while checking. Shift Pattern is PRN123. In an area where you can safely check Tranz Brake, apply switch while in low gear. When switch is applied, car should not move at any RPM. When vehicle is staged and Tranz Brake applied, always be alert and ready in case the brake should release accidentally. Staging Procedures and Other Information: Staging can be done many ways. You can bump in with Tranz Brake Switch or with foot brake. If foot brake is used, we find coming in at about RPM works best, but each individual and race car is different so you be the judge. It is suggested that you use your brake at RPM for maximum life of your drive train. However, our valve body has been tested to 6200 RPM behind a 440 cu.in. engine. The choice is yours. Be sure your converter is tranz brake ready. CAUTION: First gear dry burnouts with or without tranz brake should be AVOIDED! Light chirps may be okay, but you still are playing a risky game with a Torqueflite. We suggest burning the tires to the staging line in high gear, pre-stage, clean out engine and then stage as instructed above. Do Not neutral car in the traps. For your own safety and others be sure to run a transmission blanket or transmission shield per IHRA and NHRA rules. Part #17899XA , Page #6
7 #17899XA Templet to drill hole in the 727 or 904 case for the solenoid case connector. Fig. #1 Torqueflite Tranz Brake Wiring Case Connector Momentary Switch 12V Source Delay Box If Used Fig. #1A Part #17899XA Page #7
8 Case Connector Hole Fig. #2 Fig. #3 Fig. #4 Part #17899XA Page #8
9 Accumulator Part #17131A Piston Blocker Outside of Transmission Large Diameter of Accumulator Small Diameter of Accumulator 3/16 Hole Center of Transmission CAUTION: Transmissions manufactured in 1971 and later may have a hole drilled in the bottom of the accumulator bore. This hole must be blocked. Please note that some units have an elongated hole on the side of the bore which is fine to be left as is or newer transmissions have a Part #PK35XXXXX or higher on the pan rail drivers side or Older Transmissions Part #PK34XXXXX or lower will have a hole in the bottom of the bore, but does not require being blocked. Fig. #6 - Accumulator Part #17899XA Page #9
10 Lever Adjusting Screw & Locknut Lever (Short) Strut Pin O Ring Band Link & Anchor Fig. #7 - Reverse Band & Linkage Remove Seal Ring Piston Piston Plug Piston Spring Snap Ring Plug Spring Retainer Spring Snap Ring Install Shim Over Piston Plug Shaft Fig. #8 - Brake & Reverse Servo Part #17899XA Page #10
11 Special Instructions for Pro light Racing (Will also enhance performance on a full tree.) 1. Remove Transmission from Car. 2. Remove Front Clutch Drum. 3. Drill Front Clutch Drum Fig. #9. If you drill this hole, you then Must Block Front Pump Breather, Fig. #10. Then install a Rear Breather in Case or Tail Housing, Fig Install #17090 Springs in Front Clutch Drum. (Suggest this for Pro Tree and Full Tree). Front Clutch Drum Fig. #9 Drill.063 (1/16) Bleed Hole Fig. 10 Block Front Pump Breather Rear Tail Housing Case Rear Fig. #11 Rear Breather Part #17899XA Page #11
12 Water Burnout Instructions Tire development brought about the need to get tires hot in order to get maximum traction. This started the use of water to get tire speed up quickly. Now tires are getting hot, but automatic transmissions are subject to destruction if not careful! Please read carefully the following suggestions for your transmission: Chrysler/Amer. Mtrs. 727, 904, 998 & 999 Transmissions All water burnouts should be started in second gear and shift to third if necessary. If you should start burnout in first, shift immediately to second before tires come out of water. No matter whether it be second or third gear you are in as you come out of the water, you should start to deaccelerate engine or do a power burnout directly to the staging line being sure tires never grab dry pavement. The power burnout provides the best E.T. s if no dry burnouts are done. No matter if you have a tranz brake or not, we suggest not doing dry burnouts! Note - Rear End Breakage & Driveshaft Breakage: If rear end or driveshaft breaks while in first gear acceleration or burnout, remove transmission and check rear roller clutch for damage. Chrysler Flexplates Chrysler Special Support Transmissions Torque Converters Valve Bodies Tranz Boxes CHEETAH SCS Shifters CHEETAH E-Shift Controller Part #17899XA Page #12
CHEETAH E-SHIFT Pro Series Valve Body (Positively Not For Street Use) Fits Torqueflite 727 & (Non Lock-Up)
1535 Owens Road, Jacksonville, FL 32218 - (904)741-4850 - FAX (904)741-4853 www.turboaction.com CHEETAH E-SHIFT Pro Series Valve Body (Positively Not For Street Use) Fits Torqueflite 727 & 904 1966-90
More informationIMPORTANT - Water Burnout Instructions on Page 4.
1535 Owens Road, Jacksonville, FL 32218 Phone (904) 741-4850 *** FAX (904) 741-4853 www.turboaction.com CHEETAH XtremeAction Race Only Manual Valve Body - PRN321 Part # 17880XA -Torqueflite 727 & 904 1966-Up
More informationCHEETAH PRO SERIES TRANZ BRAKE VALVE BODY (Not for Street Use) Part #24941
1535 Owens Road, Jacksonville, FL 32218 Phone 904-741-4850 * Fax 904-741-4853 www.turboaction.com CHEETAH PRO SERIES TRANZ BRAKE VALVE BODY (Not for Street Use) Part #24941 Reverse Shift Pattern (PRN123)
More informationCHEETAH Competition Manual Valve Body - (PRN321) Part #27253
1535 Owens Road, Jacksonville, FL 32218 Phone 904-741-4850 * Fax 904-741-4853 CHEETAH Competition Manual Valve Body - (PRN321) Part #27253 Turbo Hydro 200-1976-Up FIRST, READ INSTRUCTIONS CAREFULLY, THEN
More informationTorqueflite Manual/Automatic Valve Body
TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts
More informationTorqueflite Trans-Scat Kit
TCI 220000 Torqueflite Trans-Scat Kit This kit can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts and procedures. Work
More informationCHEETAH STREET MANUAL/AUTOMATIC BODY (PRN321) Part #23250
1535 Owens Road, Jacksonville, FL 32218 Phone 904-741-4850*****Fax 904-741-4853 www.turboaction.com CHEETAH STREET MANUAL/AUTOMATIC BODY (PRN321) Part #23250 *Turbo Hydro 350 1969-80 (Non-Lockup) FIRST,
More informationCHEETAH SCS SHIFTER Part #70003B Fits: Ford C4 (1964-Up) & Ford C6 (1966-Up) (Note: Will not fit any four-speed automatic transmissions)
70003B 1535 Owens Road, Jacksonville, FL 32218 Phone (904) 741-4850***FAX (904) 741-4853 WWW.turboaction.com CHEETAH SCS SHIFTER Part #70003B Fits: Ford C4 (1964-Up) & Ford C6 (1966-Up) (Note: Will not
More informationReturn to Instruction Sheet index TCI Torqueflite Trans-Scat Kit
Page 1 of 11 Return to Instruction Sheet index TCI 220000 Torqueflite Trans-Scat Kit This kit can be installed in a few hours by carefully following directions. Read all instructions first to familiarize
More informationChrysler TorqueFlite Shift Improver Kit Part No A-727 (V-8) A-904 (V-8) (A-998 & A-999)
FORM # 9500606-03 Installation Instructions Chrysler TorqueFlite Shift Improver Kit Part No. 10225 1971-1977 A-727 (V-8) 1971-1977 A-904 (V-8) (A-998 & A-999) 1998, 2005, 2010 by B&M Racing & Performance
More informationTCI Trans-Scat
Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive
More informationCHEETAH SCS SHIFTER. Part # FITS: Ford C4 (1964-Up) & Ford C6 (1966-Up) (Note: Will not fit any four-speed automatic transmissions)
70013 CHEETAH SCS SHIFTER Part #70013 FITS: Ford C4 (1964-Up) & Ford C6 (1966-Up) (Note: Will not fit any four-speed automatic transmissions) Parts Breakdown 1 - Ford Control 1-70080B Gear Position Indicator
More information1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and
Installation Instructions for 603107 Valve Body Kit C-4 1970 & Later Tools Required Speed Handle or Ratchet 3/8 Drive 1/2 Socket 3/8 Drive 7/16 Socket 3/8 Drive 5/16 Socket 3/8 Drive Small Screwdriver
More informationInstallation Instructions Shifter Improver Kit Fits:1988 and Later TurboHydramatic 400, TH-400/TH-475 (3L80/3L80-HD) Catalog # 20261
Installation Instructions Shifter Improver Kit Fits:1988 and Later TurboHydramatic 400, TH-400/TH-475 (3L80/3L80-HD) Catalog # 20261 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationReturn to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C
Page 1 of 6 Return to Instruction Sheet index TCI 326300 Installation Instructions for Turbo Hydramatic 350C & 250C NOTE: This kit was not intended for installation in transmissions that are in poor general
More informationReturn to Instruction Sheet index. Installation Instructions For C-4 70 and Later, Except 70 Falcon
Page 1 of 8 Return to Instruction Sheet index TCI 260100 Trans-Scat Automatic Transmission Installation Instructions For C-4 70 and Later, Except 70 Falcon TCI 260100 Kit Contains: Qty. Description One
More informationInstallation Instructions Transpak Fits: GM Turbo-Hydramatic 400, Turbo-Hydramatic 375 and M40 Automatic Transmission Catalog # 20228
Installation Instructions Transpak Fits: 1965-1987 GM Turbo-Hydramatic 400, Turbo-Hydramatic 375 and M40 Automatic Transmission Catalog # 20228 WORK SAFELY! For maximum safety, perform this installation
More informationTCI TRANS-SCAT
Page 1 of 9 Return to Instruction Sheet index TCI 360000 TRANS-SCAT Installation Instructions for FORD C-6 Transmissions TCI s TRANS-SCAT kit will allow you to calibrate the performance of your transmission.
More informationPart No amatic 350
Watch our installation video on YouTube Installation Instructions Shift Improver Kit Part No. 30262 1968-1981 TurboHy urbohydr drama amatic 350 B&M Racing and Performance Products 2002 Congratulations!
More informationCHEETAH SCS SHIFTER Part # 70012
70012 1535 Owens Road, Jacksonville, FL 32218 Phone (904)741-4850***FAX (904)741-4853 www.turboaction.com CHEETAH SCS SHIFTER Part # 70012 Fits: GM Turbo 200 (ALL), Turbo 250 (ALL), Turbo 350 (ALL) & Turbo
More informationTCI Trans-Scat
Page 1 of 5 Return to Instruction Sheet index TCI 350000 Trans-Scat Installation Instructions For TURBO HYDRAMATIC 350 This kit will allow you to reprogram your transmission to meet your driving needs
More informationTH400 STREETFIGHTER SERIES VALVE BODY MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS
1 INSTRUCTIONS TH400 STREETFIGHTER SERIES VALVE BODY 1965-87 MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS TCI 222400 TCI 222400 ALLOWS AUTOMATIC SHIFT FEATURES IN THE DRIVE POSITION Thank you for choosing
More informationPG COMPU-FLOW TRANSBRAKE Part #s , , , , ,
Installation Instructions 6747 Whitestone Rd Gwynn Oak, MD 21207 (410) 298-4343 FAX: (410) 298-3579 www.atiracing.com PG COMPU-FLOW TRANSBRAKE Part #s 203050, 203051, 203250, 203300, 203350, 203070 PACKING
More informationPRO RATCHET UNIVERSAL SHIFTER
Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,
More informationCaution! Caution! Air/CO2 and Electric Shift Devices
Caution! Caution! Air/CO and Electric Shift Devices You must set rpm in the CHEETAH E-SHIFT Controller before starting vehicle! Failure to do this could cause injury and or property damage! Read Instructions
More informationTranspak. Torqueflite Part No (1978½-1996) Part No ( ) 2008, 2002 by B&M Racing and Performance Products
Installation Instructions Transpak for Torqueflite Part No. 10227 (1978½-1996) Part No. 10228 (1962-1978) 2008, 2002 by B&M Racing and Performance Products Congratulations. You have just purchased the
More information1 of 25 9/12/2013 9:07 PM
1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the
More information1991 TRANSMISSION SERVICING Automatic Transmission. Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT
Article Text ARTICLE BEGINNING 1991 TRANSMISSION SERVICING Automatic Transmission Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT IDENTIFICATION MITSUBISHI AUTOMATIC TRANSMISSION APPLICATIONS
More informationStealth Pro Ratchet Shifter
Installation Instructions Stealth Pro Ratchet Shifter Part Number 81120 & 81121 (see www.bmracing.com for the latest technical product information) 2010, 2006 by B&M Racing and Performance Products The
More informationTCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve.
TCI 221100 Turbo 400 Full Manual Valve Body Shift Pattern: Park Reverse Neutral First Second Third This Kit Contains: (1) Turbo 400 Full Manual Valve Body (1) Separator Plate & Gaskets (1) Pressure Regulator
More information26 November 2009 Valve Body # / BD VALVE BODY. For Dodge 5.9L 12V Cummins Trucks
26 November 2009 Valve Body #1030410 / 1030415 1 BD VALVE BODY For 1991-1995 Dodge 5.9L 12V Cummins Trucks - - I n s t a l l a t i o n I n s t r u c t i o n s - - 1030410 1991-1993 Dodge (4 Spd) 618 1030415
More informationThis kit contains all parts necessary to obtain two levels of performance depending on intended use:
Installation Instructions SHIFTER IMPROVER KIT Fits: Chrysler, Dodge, Plymouth w/torqueflite 66-70 TF A-727 (All) 66-77 TF A-904 (6 Cyl) / 68-70 TF A-904 (8 Cyl) Catalog # 10226 WORK SAFELY! For maximum
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationInstallation Instructions for TCI Turbo 700R TCI Turbo 700R
Installation Instructions for TCI 378805 Turbo 700R4 1982-1984 TCI 378905 Turbo 700R4 1985-1993 KIT INTRODUCTION Read all instructions first to familiarize yourself with the parts and procedures. Work
More informationTRANSMISSION SERVICING - A/T
TRANSMISSION SERVICING - A/T 1992 Infiniti G20 1991-92 TRANSMISSION SERVICING Automatic Transmission G20 IDENTIFICATION INFINITI AUTOMATIC TRANSMISSION APPLICATIONS Model Transmission Model G20... (1)
More informationPART # 4VB/RPFMTB Reverse Pattern Full Manual Transbrake Valve Body Assembly
PART # 4VB/RPFMTB Reverse Pattern Full Manual Transbrake Valve Body Assembly Extensive research and development was performed during the inception of this product and has continued throughout its production.
More informationTurbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd
TCI 221500 Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd This Valve Body will neutralize at shut-down by putting shifter In 2nd gear position This Kit Contains: (1) Turbo
More informationTRANSMISSION PARTS Instructions. Solenoid Regulator Valve Retainer Shim. Main Pressure Regulator Valve
TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-AODE NOTE: This kit is fully compatible with '91 '95 only. Identified by alignment pins 13mm heads. This kit will not work on '96 Later units.
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More information2244 West McDowell Road Phoenix, AZ RACE (fax)
2244 West McDowell Road Phoenix, AZ 85009 602-257-9591 1-800-274-RACE 602-340-8429 (fax) www.hughesperformance.com HUGHES PERFORMANCE HP2215 VALVE BODY Installation Instructions 9/24/16 For over 45 years
More informationTORQUEFLITE INTRODUCTION NOTE:
Installation Instructions SHIFTER IMPROVER KIT Fits: Chrysler, Dodge, Plymouth w/torqueflight 71-77 TF A-727 (All) / 71-77 TF A-904 (8 Cyl) Catalog # 10225 WORK SAFELY! For maximum safety, perform this
More informationPhoto 1. Shift pattern gate plate
Installation Instructions MAGNUM GRIP STREET BANDIT SHIFTER Fits: GM, Chrysler, and Ford Automatic Transmissions See Application Guide for Specific Vehicles Catalog # 81050 WORK SAFELY! For maximum safety,
More information12 September 2012 Valve Body # , , ,
12 September 2012 Valve Body # 1030416, 1030417, 1030418, 1030419 1 BD VALVE BODY For 1996-2004 Dodge 5.9L 12V/24V Cummins Trucks -- I n s t a l l a t i o n I n s t r u c t i o n s -- 1030416 1996-1998
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationTechnical Support (707)
Installation Instructions UNIMATIC SHIFTER Fits: GM, Powerglide, Ford and Chrysler Transmissions See Application Guide for Specific Vehicles Catalog # 80775 WORK SAFELY! For maximum safety, perform this
More information1994 Mazda MX-5 Miata. TRANSMISSION SERVICING - A/T TRANSMISSION SERVICING Mazda Automatic Transmission
IDENTIFICATION TRANSMISSION SERVICING - A/T 1990-94 TRANSMISSION SERVICING Mazda Automatic Transmission NOTE: On models with anti-theft radio system, obtain code number from customer to deactivate radio
More informationHIPSTER S TURBO 350 TRANSBRAKE
HIPSTER S TURBO 350 TRANSBRAKE THIS IS THE QUICKEST AND MOST CONSISTENT T350 BRAKE AVAILABLE. AS WITH ANY NEW PRODUCT THERE ARE CERTAIN STEPS THAT MUST BE FOLLOWED TO INSURE YOUR SUCCESS WITH IT. PLEASE
More informationTransmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
More informationAODE ( 96 & LATER) SC-AODE-1. Transmission Reconditioning Kit FULL COMPATIBILITY IMPORTANT VALVE BODY PARTS REASSEMBLY PARTS
AODE ( 96 & LATER) Transmission Reconditioning Kit FULL COMPATIBILITY SC-AODE-1 Full compatibility with 1996 and later units. Identified by alignment pins with 10mm head and.173" pin diameter. IMPORTANT
More informationInstallation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic)
Installation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic) Catalog# 3160020 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and
More informationInstallation Instructions Pro Bandit Shifter Fits: GM Powerglide Automatic Transmissions
Installation Instructions Pro Bandit Shifter Fits: 1962-1973 GM Powerglide Automatic Transmissions Part # 80793 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and
More informationWARNING! THIS SHIFTER IS FOR RACING USE ONLY. NOT FOR STREET USE!
Installation Instructions Quarter Stick Shifter Fits: GM Powerglide w/forward or reverse valve body. Also fits: TH250, TH350, TH375 and TH400 Auto transmissions w/reverse valve body. Catalog# 3162020 WORK
More informationTRANSMISSION PARTS Instructions
TRANSMISSION PARTS Instructions Sure Cure Kit Part No. SC-4T65E GM 4T65-E Valve Body Parts Boost Valve Kit 84754-30K Patent No. 6,832,632 TCC Apply Valve Kit 84754-43K Patent No. 7,100,753 TCC Regulated
More informationAUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More information2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
More informationINSTALLATION INSTRUCTIONS LOKAR COLUMN SHIFT LINKAGE
INSTALLATION INSTRUCTIONS LOKAR COLUMN SHIFT LINKAGE Part No. ACA-1807 (Ford AOD) STOP! PLEASE READ ALL INSTALLATION INSTRUCTIONS BEFORE BEGINNING INSTALLATION. CALL LOKAR FOR ANY QUESTIONS OR UNCERTAINTIES
More informationTransaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.
«1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept
More informationINSTALLING THE NEUTRAL SAFETY SWITCH WIRES
Installation Instructions Magnum Grip Pro Bandit Shifter Part Number 81045 & 81046 2004, 2003 by B&M Racing and Performance Products (Visit www.bmracing.com for additional products and product information)
More informationPART # 4VB/FPFMTB Forward Pattern Full Manual Transbrake Valve Body with Engine Braking and Safe Neutral
PART # 4VB/FPFMTB Forward Pattern Full Manual Transbrake Valve Body with Engine Braking and Safe Neutral NOTE: This product should be installed by a professional transmission mechanic who is fluent with
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationSection X STEERING DATA AND SPECIFICATIONS. 21 degrees 45 minutes -f- or 1 degree (inner wheel when outer wheel is 20 degrees)
76 Section X DATA AND SPECIFICATIONS MODELS MC-1 MG-2 MC-3 MY-1 Steering Type Manual Power Worm and Three Tooth Roller None None None Rack and Gear Sector, Recirculating Ball Nut Ratio Manual 20.4... Power
More informationInstallation Instructions Street Bandit Shifter
Installation Instructions Street Bandit Shifter Part Number 80797 (see www.bmracing.com for the latest technical product information) 2006, 2000 by B&M Racing and Performance Products The B&M Street Bandit
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will
More information46RE, 46RH, 47RE, 47RH ZIP KIT
46RE, 46RH, 47RE, 47RH ZIP KIT PART NUMBER 46-47RHE-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. installation Diagram 7 1 Separator
More informationChrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT
Chrysler 46RE, 46RH, 47RE, 47RH SURE CURE KIT PART NUMBER SC-46-47RHE-OS INSTALLATION GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Sure Cure kit contents.
More informationInstallation Instructions Pro Stick Shifter
Installation Instructions Pro Stick Shifter Part Number 80701, 80702 & 80706 2012, 2010, 2008, 2001, 1998 by B&M Racing and Performance Products The B&M Pro Stick shifter #80701 and #80706 comes equipped
More information2244 West McDowell Road Phoenix, AZ RACE (fax)
2244 West McDowell Road Phoenix, AZ 85009 602-257-9591 1-800-274-RACE 602-340-8429 (fax) www.hughesperformance.com HUGHES PERFORMANCE HP2211R VALVE BODY Installation Instructions rev. b 10-2016 For over
More informationInstallation Instructions Right Hand Drive Megashifter
Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles
More information2244 West McDowell Road Phoenix, AZ RACE (fax) INSTALLATION INSTRUCTIONS FOR
2244 West McDowell Road Phoenix, AZ 85009 602-257-9591 1-800-274-RACE 602-340-8429 (fax) www.hughesperformance.com INSTALLATION INSTRUCTIONS FOR HP2215 TH400 3-SPEED TRANSBRAKE VALVE BODY KIT Please read
More information2001 Chevrolet Corvette AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul
2001-03 AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transmission installation. Oil cooling system contamination may cause premature
More information235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
More informationInstallation Instructions StarShifter
Installation Instructions StarShifter Part Number 80675 2000 by B&M Racing & Performance Products LLC The B&M StarShifter can be used in vehicles equipped with most popular three speed automatic transmissions.
More informationTCI Ford C-6 TransBrake Valve Body Shift Pattern: Park, Reverse, Neutral, First, Second, Third
1 INSTRUCTIONS TCI 421500 Ford C-6 TransBrake Valve Body Shift Pattern: Park, Reverse, Neutral, First, Second, Third Thank you for choosing TCI products; we are proud to be your manufacturer of choice.
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationHP7482X POWERGLIDE TRANSBRAKE KIT
INSTALLATION INSTRUCTIONS FOR: HP7482X POWERGLIDE TRANSBRAKE KIT Please read all instructions carefully before beginning installation! Hughes Performance 2244 West McDowell Road Phoenix, Arizona 85009
More informationInstallation Instructions Shift Improver Kit for THM200-4R Transmission
Installation Instructions Shift Improver Kit for 1981-90 THM200-4R Transmission ongratulations! You have just purchased the most complete and versatile recalibration kit available for the TH- 200-4R transmission.
More informationIMPORTANT NOTES This B&M Non-Lockup Converter will not fit 1978 and later Torqueflite transmissions originally equipped with lock-up converters.
Installation Instructions Holeshot 2400 Torque Converter Fits: 1967-1981 Chrysler, Dodge, Plymouth w/torqueflite A727 Automatic Transmission Catalog # 10415 WORK SAFELY! For maximum safety, perform this
More informationInstallation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in
More information2003 E-Series Workshop Manual
Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will
More informationRELEASING PRESSURE IN THE HYDRAULIC SYSTEM,
Testing And Adjusting Introduction NOTE: For Specifications with illustrations, make reference to SPECIFICATIONS for 225 EXCAVATOR HYDRAULIC SYSTEM, Form No. SENR7734. If the Specifications are not the
More informationB&M / INTRODUCTION
INSTALLATION INSTRUCTIONS FOR B&M AUTOMATIC TRANSMISSIONS REPLACING GM TH350, TH400, and TH700R4 / 4L60 (not including 4L60E / electronic shift models) B&M part numbers: 102002-103005 - 107101-107104 107105-107106
More informationPage 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationStep 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed.
1 INSTRUCTIONS TCI 274500/274501 4L80E Trans Brake Valve Body Thank you for choosing TCI products. We are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning
More informationHurst VMATIC3 INSTALLATION
FORM 159 8530 07/12 Hurst VMATIC3 3-Speed & 4-Speed Automatic Shifter Catalog #3838530 2012 by Hurst Performance The Hurst Vmatic3 shifter can be used in vehicles equipped with most popular three speed
More informationTCI FastGate Shifter Installation Instructions
151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The
More informationInstallation Instructions Megashifter
Installation Instructions Megashifter The B&M Megashifter shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. Your B&M Megashifter comes equipped
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More informationASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
More informationHIPSTER'S ALUMINUM POWERGLIDE TRANSBRAKE (P/N: 12748A) CAUTION
W140N10145 Fond Du Lac Ave. Germantown, WI 53022 Phone: (262) 251-7777 Email: info@autotransdesign.com www.autotransdesign.com HIPSTER'S ALUMINUM POWERGLIDE TRANSBRAKE (P/N: 12748A) CAUTION Please read
More informationAUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul
1997-98 AUTOMATIC TRANSMISSIONS General Motors Corp. Hydra-Matic 4L60-E Overhaul APPLICATION TRANSMISSION APPLICATIONS Application Corvette Transaxle 4L60-E IDENTIFICATION The 4L60-E transmission can be
More informationGeo Prizm ( LSi) Toyota Celica 1.8L (1994)
Page 1 of 140 ARTICLE BEGINNING APPLICATION TRANSMISSION APPLICATIONS Application Geo Prizm (1993-94 LSi) Toyota Celica 1.6L (1993) Celica 1.8L (1994) Celica 2.2L (1993) Corolla 1.8L MR2 Paseo Transaxle
More informationTRANS-SCAT Installation Instructions for Ford AOD
TCI 436000 TRANS-SCAT Installation Instructions for Ford AOD 1980-1993 TCI 436000 Kit Contains: Qty. Description Five (5) Gaskets: Three (3) Valve Body One (1) Filter One (1) Duraprene Pan Two (2) Springs:
More informationInstallation Instruction for B&M Transpak for THM200-4R Transmission
Installation Instruction for B&M Transpak for 1981-90 THM200-4R Transmission Part No. 35229 B&M Racing & Performance Products 1999 ongratulations! You have just purchased the most complete and versatile
More informationASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)
307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)
More informationCARBURETION. Carburetor Identification. Models , , , , , , , , , , ,
Carburetor Identification Models 110400, 110600, 111400, 111600, 113400, 120400, 120600, 121400, 121600, 122600, 123400, 123600 Models 28S700, 311700 Service Carburetor Briggs & Stratton/Walbro LMS Models
More informationGftOUP 4 PARKING BHAKE
PARKING BRAKE 4-1 GftOUP 4 PARKING BHAKE CONTENTS Page Data and Specifications... 1 External Contracting Type Parking Brake...... 2 Parking Brake Band Lining 3 Parking Brake Internal Expanding Type 5 Parking
More information