3M Fiber Dome Closure FDC 10

Size: px
Start display at page:

Download "3M Fiber Dome Closure FDC 10"

Transcription

1 3M Fiber ome losure F 10 With 3M Fiber Optic Splice Tray 2541 Instructions 1.0 General 2.0 Kit ontents The 3M Fiber ome losure F 10 can accommodate two 1.06" (27 mm) main cables, five 0.71" (18 mm) branch cable and 15 standard flat drop cables. It will accommodate both dielectric and armored cables. Grounding kits must be purchased separately. A B H Tray apacity 6 3M Splice Tray 2541 Splice Tray apacity (per tray) 48 Single Fusion (288 Max) 144 Mass fusion (432 Max) 24 3M Fibrlok Mechanical Splice (144 Max) Main ables " (6.5 mm) min to 1.06" (27 mm) max diameter Branch ables " (5 mm) min to 0.71" (18 mm) max diameter Ground Lugs None, 3, 5 or 7 Air Valve 5.0 PSI Max (34 kpa max) flash Express Storage 72" (1.8 m) typical A. 3M Fiber ome losure B. Base assembly. 3M External able Assembly Module (EAM) able Entry Port 18 mm (Optional). 3M Fiber Optic Splice Tray 2541 on mounting plate E. 3M Fiber Optic Splice Tray 2541 loose parts F. 3M External able Assembly Module (EAM) ouble able Entry Port loose parts G. 3M External able Assembly Module (EAM) ouble able Entry Port washer sets H. Transition tube (dependent on order) Visually inspect all components. If any component is missing or appears damaged, do not install. all 3M customer service at for a replacement product. F E G August

2 A J A B I G B H E F 3M ouble able Entry Port EAM 27 MM loose parts A. Washers sets (4 sets) B. able Ties. Sheath scuff. able clamp shells (4 sets) E. Oval gasket F. Mastic tape rolls (2) G. Mastic rope H. Silicone lubricant I. Alcohol wipe J. able gauge decal 3M 2.4 MM Single Fusion Tray SF loose parts (Qty. and type of insert dependent on configuration and order) A. 2.4 mm single fusion splice inserts (4) B. Tray label. able ties. Buffer tube gripper tape A A B B 3M Mass Fusion Tray MF loose parts (Qty and type of insert dependent upon configuration) A. Mass fusion inserts (2) B. Tray label. able ties. Rubber gripper 3M 3.0 MM Single Fusion Tray SF loose parts (Qty. and type of insert dependent on configuration and order) A. 3.0 mm Single fusion inserts (4) B. Tray label. able ties. 3M Scotchmate Fastener 2

3 B A A F B 3M Fibrlok Splice Insert for Tray 2521-FL-A-Mod loose parts (Qty and type of insert dependent upon configuration) E G A. 3M Fibrlok Splice inserts (5) B. Tray label. able ties. 3M Scotchmate Fastener K 3M Fiber ome losure Overview A. Air valve B. Security screw. Wire latch bails. ouble EAM assembly E. 18 mm port plugs (5) F. Grounding studs (7 Max) G. ouble EAM clamp I E 3.0 ome Removal L M B F H A 3.1 Loosen security screw by using a 3/8" (10 mm) can wrench until the screw disengages with the dome. Note: Failure to disengage security may lead to closure damage if dome removal is attempted. J G 3M able Entry Kit EAM-18 MM-S (Optional only included in certain configurations) A. able gauge decal B. EAM body. Locking fork. able tie E. Round cable grommets (4) F. EAM nut G. lamp screws (2) H. able strength member (SM) clamp I. ap J. able clamp sets K. Silicone lubricant L. Spacer washers M. O-Ring 3

4 3.2 Grasp both latch bails and pull upward rotating both latches past 90 degrees to separate the dome from the base. Remove the dome from the base. 4.2 The splice tray and mounting plate can now be removed. Adjustable Stack Storage 4.0 Splice Tray and Storage Basket Features Overview 4.1 Splice tray and mounting plate can be removed by loosening the screw and sliding the tray locking bracket down. 4.3 Note that the splice tray and mounting plate can be relocated at three different heights enabling more room underneath the splice tray in the storage basket. Maximum tray capacity is in position one. Position Tray apacity

5 4.4 If the splice tray mounting plate is mounted on position three, the tray plate lock and screw needs to be relocated in the upper hole as shown. When the splice tray mounting plate is mounted on position one and position two, use lower hole for the tray plate lock and screw. 5.0 Temporary Work Surface Arrangement 5.1 When the closure is mounted horizontally (such as aerial) the tray and mounting plate can be relocated allowing the craftsperson to covert it to a temporary work surface. Simply remove the tray and relocate it by inserting the tabs fully into the corresponding slots in the basket. This feature requires the craftsperson to allow additional slack when routing and splicing fiber. (ables and fiber not shown for clarity.) 4.5 Reposition the splice tray mounting plate at the desired level. Push the tray fully into the slots. Ensure all four tabs on the mounting plate are engaged in the correct level slots. 5.2 The tray mounting plate will lock in place when in the lowered position. Note that basket is configured to accept the splice tray and mounting plate with the closure mounted in both left and right handed orientation. Note: This work surface is intended for light duty excessive weight may damage components. 4.6 Lock the plate by sliding the lock up against tab under the mounting plate and retighten the screw to ten inch lbs. 5

6 5.3 Note that the center tabs can be bent down flush with basket allowing a more open slack storage area. (This step should be performed if storing in excess of 6') 7.0 For Armored ables Only 4 (200mm) LEAVE HALF OF ABLE SHEATH W/METALLI SHIELING TO ATTAH GROUNING 6 (150mm) TRIM SM RO(S) MEASURE SHEATH OPENING TO HERE Otherwise same as dielectric cable preparation. 7.1 Prepare cable sheath for grounding and install ground onto tab of cable sheath as shown. 6.0 ielectric Main able Preparation (No Ground) EXPRESS LOOSE BUFFER TUBE ABLE 6 (150mm) TRIM SINGLE OR UAL SM ROS 3 (75mm) SUFF SHEATH ON ALL ABLES TYPIAL ABLE PREP 6 (150mm) TRIM SINGLE OR UAL SM ROS 72 MAX (1.8m) SHEATH REMOVE EXPRESS ENTRAL TUBE ABLE 8 (200mm) ENTRAL TUBE 3M Internal Ground Kit 6 AWG TYPIAL ABLE PREP 72 MAX (1.8m) SHEATH REMOVE 6 (150mm) TRIM SINGLE OR UAL SM ROS BRANH OR ROP ABLE TYPIAL ABLE PREP 48 (1.2m) SHEATH REMOVE 3M Grounding Kit EAM-GN-14-AWG 6 (150mm) TRIM SINGLE OR UAL SM ROS 8 (200mm) ENTRAL TUBE TRIMME TYPIAL ENTRAL TUBE ABLE PREP 72 (1.8m) SHEATH REMOVE 6

7 7.2 Wrap sheath and ground terminal with tape to protect fibers from sharp edges. 3M Grounding Kits must be purchased separately: EAM-GN-6-AWG EAM-GN-14-AWG Route the fiber into the basket for storage. Arrange fiber to allow slack for splicing. Note: A center tab feature in the slack storage basket allows cable slack to be stored in two different levels M ouble able Entry Port EAM-27 MM- and able Preparation 8.1 Refer to the instructions supplied with the 27 MM EAM ouble Entry Port for removal, installation, cable preparation and cable grounding. 8.4 Ribbon slack can be stored in the same manner. It may be necessary to remove the ribbon transport tube in order to store the slack without kinking the tube or fiber. Fiber Slack Storage 8.2 Route the cable slack into storage basket. One technique for storing express buffer tube cable is described here: Step 1 Step 2 Step 3 7

8 9.0 Splice Tray Preparation 9.1 Remove the tray cover by pressing down on the end of cover and pulling cover as shown. 9.3 Install splice inserts by placing edge of insert under tabs in nest on tray. Bow insert and install under tabs on opposite side. 9.4 able ties can be pre-installed. 9.2 Splice inserts available (Quantity and type dependent on configuration and order): 3.0 mm fusion splice insert 2.4 mm fusion splice insert Mass fusion splice insert 3M Fibrlok Splice Insert 8

9 Storage basket mounted splice tray 9.5 etermine slack requirements needed. Route fiber as needed to maintain minimum bend radius. Note that the fiber is routed into the splice tray from the opposite side of the storage basket in order to minimize the chances of kinking the fiber Buffer Tube Preparation 10.1 Ring and remove buffer tube sheath per best company practice. lean fiber. Make sure any gel or grease is removed. lean until fiber squeaks. ut ½" (12 mm) of 3M Scotchmate Fastener and wrap around the end of buffer tube. Work surface mounted splice tray Splice tray positioned externally 10.2 Install into tray and secure with two cable ties. 9

10 11.0 Ribbon Fiber Preparation 11.1 ut a one-inch (25 mm) section of the rubber gripper supplied with the splice tray kit and use to secure buffer tubes or ribbon fiber (up to six ribbons) to tray. Route and secure ribbon cable as needed. Note: Only use the middle two inserts when splicing ribbon fiber Installing transition tube for pass through applications 12.1 ut six to eight inches of tubing provided for you in the kit Tie down one end at the first position on the left side of tray #1 and other end at the furthest position to the right on tray # Attach splice log decal to cover. Note that bottom portion of decal can be cut off and used to identify individual trays arefully feed the pass through fibers through the transition tubing from tray #1 through to tray # Route and splice fibers according to best company practice. 10

11 13.4 Remove the splice tray by rotating the tray up and twisting the tray at the same time Adding and Removing Splice Trays 13.1 To add a tray, align the rectangular tab on the pivot vertically. rop one side into the mating pivot hole in the lower tray Unlock the tray by depressing the locking arm. This allows the tray to be free to pivot Now push the upper tray toward the engaged pivot Install the tray cover by placing cover on tray. Align the cover with smaller triangular shaped tabs on spice tray Align and lower to engage the opposite pivot. 11

12 13.7 Lock the cover in place by sliding the cover under the tabs as shown Secure the trays by attaching retaining straps Prepare and install branch or drop cable using instructions supplied with 3M External able Assembly Module (EAM) able Entry Port 18 mm able Installation 14.1 Remove the plug by first removing the retaining fork and then pulling the plug out ome Installation 15.1 Ensure both the dome seal area and base O-ring are free of dirt or any damage. If needed, clean area and apply a light film of supplied silicone lubricant. Failure to maintain a clean seal area may lead to leakage. Note: Follow health, safety and environmental information. Refer to product label or Material Safety ata Sheet for silicone lubricant. 12

13 15.4 Tighten the security screw and torque to 30 inch-lbs Install the dome on the base by first aligning the security screw features on both the base and dome. Slide dome onto base A cable tie can be used for additional security of the latches and dome if needed. Insert through latches across the back side of the dome as shown Engage both latches and push firmly to seat the dome onto the base The assembled unit can be flash tested at five PSI (34 kpa) maximum. Note: Release pressure after testing. 13

14 15.7 External grounding can be added to ground lug on base. Torque to inch-lbs Accessories UP Number 3M I escription EAM-GN-6-AWG EAM (18, 20, 27MM) ABLE GN (6 AWG) EAM-GN-14-AWG EAM ABLE GN (14 AWG) EAM-27MM- 27MM OUBLE ABLE ENRY PORT SF-2.4MM, 2541 FO Splcie Tray 48 Single Fusion 2.4 mm SF-3.0MM, 2541 FO Splcie Tray 48 Single Fusion 3.0 mm MF-12RF, 2541 FO Splcie Tray 144 Mass Fusion 12 Ribbon EAM-18MM-S, 18MM Single EAM able Entry Port Kit 3M, Fibrlok and Scotchmate are trademarks of 3M ompany. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INLUING, BUT NOT LIMITE TO, ANY IMPLIE WARRANTY OF MERHANTABILITY OR FITNESS FOR A PARTIULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 ommunication Markets ivision 6801 River Place Blvd. Austin, TX Please Recycle. Printed in USA. 3M All Rights Reserved.

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm. Instructions. October C

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm. Instructions. October C 3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900-µm Instructions October 2010 78-8140-1581-0-C Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide

3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide 3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide Installing Tall Skirt on SVC and SVE cabinets Instructions July 2016 78-0015-3067-0 2 July 2016 78-0015-3067-0 Contents 1. General

More information

SLiC Aerial Terminal and Spiral End Seal for use with AMP* Quiet Front Terminal Blocks

SLiC Aerial Terminal and Spiral End Seal for use with AMP* Quiet Front Terminal Blocks SLiC Aerial Terminal and Spiral End Seal for use with AMP* Quiet Front Terminal Blocks Instructions June 2002 78-8130-2161-1-B 1 Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Cable Preparation...

More information

3M Locator Plate

3M Locator Plate 3M Locator Plate 3443-113 Instructions for the Assembly of 3M Tripolarized Wiremount Sockets 1.0 General The 3M Locator Plate 3443-113 was designed to aid in the assembly of the 3M Mini Socket Connector.50

More information

3M Closure System 2-Type Cover (505)

3M Closure System 2-Type Cover (505) 3M Closure System 2-Type Cover (505) Installation Instructions May 2009 78-8140-1009-2-B Contents 1.0 3M Closure Kit 2-Type Contents...3 2.0 Cover Installation...4 3.0 Closure Re-entry...6 4.0 Accessories...9

More information

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions

3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions 3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions February 2008 78-8140-1581-0 Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS

3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS 3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS Instructions January 2009 78-8140-3691-5-A Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber

More information

3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination

3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination 3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working around energized electrical systems may

More information

Cable Ties. Data Sheet

Cable Ties. Data Sheet Cable Ties Data Sheet Product Description 3M Cable Ties are molded from 6/6 Nylon and are available in a variety of sizes, styles and colors including weather resistant black for outdoor use. Agency Listings

More information

3M Locator Plate

3M Locator Plate M Locator Plate 44-94 Instructions for the assembly of M Socket Connectors,.100" x.100" and.100" x.200" 1.0 General M Manual and Pneumatic Assembly Presses and accessory assembly equipment are recommended

More information

3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits

3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits 3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits With High-K Stress Relief For 3-Conductor Type G (Ground Wire), Copper Tape Shield, Armored Cables 7600-S-3G Series Instructions IEEE Std.

More information

3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series

3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series 3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series For 3-Conductor Copper Tape Shield Cables without Ground Wires Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working

More information

710 Splicing Rig. Instructions. January E

710 Splicing Rig. Instructions. January E 710 Splicing Rig Instructions January 2007 Table of Contents 1.0 General Statement...4 2.0 3M 710-UTK25A Splicing Rig and Field Maintenance Kit...4 3.0 Straight Splicing using the 3M 710 25-pair modules...6

More information

3M Cold Shrink Splice Kit QS-III 5536A

3M Cold Shrink Splice Kit QS-III 5536A 3M Cold Shrink Splice Kit QS-III 5536A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

Motor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables)

Motor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables) Motor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables) Instructions Kit Contents 3 Lug Covers 3 Cold Shrink Terminations 12

More information

3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm

3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm 3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm Instructions January 2009 78-8140-3696-4-A 3 Contents 1.0 Kit Contents... 3 2.0 3M No Polish LC Connector SM & MM 250/900 µm... 4 Safety Precautions

More information

3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW)

3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW) 3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW) for Tape Over Wire and Wire Over Tape Shielded Cable Instructions Class 1 Termination IEC 60840 72,5 kv 69 kv Class 325

More information

3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit

3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit 3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit With High-K Stress Relief For 3-Conductor Copper Tape Shield Cables with or without Ground Wires 7600-T-3RJS Series Instructions

More information

8400 Series Fiber Distribution System

8400 Series Fiber Distribution System 8400 Series Fiber Distribution System Instructions January 1997 34-7041-4699-1-A 1 Contents: 1.0 General... 3 2.0 System Components... 4 3.0 System Engineering... 5 4.0 Hardware Installation... 7 5.0 Cable

More information

CS Fiber Optic Splice Case. Instruction

CS Fiber Optic Splice Case. Instruction 3 2179-CS Fiber Optic Splice Case Instruction 2179-CS Fiber Optic Splice Case Description 1.0 General 1.1 The 3M 2179-CS Fiber Optic Splice Cases are closures that can be used in buried, underground, aerial,

More information

3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TS (RW)

3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TS (RW) 3M Cold Shrink Skirted Termination Kit QT-III 7672-S-8-TS (RW) for Tape Shielded Cable Instructions Class 1 Termination IEC 60840 72,5 kv 69 kv Class 325 kv BIL CAUTION Working around energized systems

More information

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8(S)-JCN

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8(S)-JCN 3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8(S)-JCN For Jacketed Concentric Neutral (JCN) Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350 kv BIL IEC 60840 72,5

More information

Cold Shrink Silicone Rubber Termination QT-III 7672-S-8-JCN

Cold Shrink Silicone Rubber Termination QT-III 7672-S-8-JCN 3 Cold Shrink Silicone Rubber Termination QT-III 7672-S-8-JCN Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class 350 kv BIL IEC 60840 72,5 kv Kit Contents: 1 Silicone Rubber Lug Seal Insulator

More information

3M Ladder Kit 3M710/MS 2 -TMK-LK

3M Ladder Kit 3M710/MS 2 -TMK-LK 3M Ladder Kit 3M710/MS 2 -TMK-LK Instructions 1.0 Summary The 3M Ladder Kit 3M710/MS2-TMK-LK is intended for mounting a communication line splicing system to a fiberglass extension ladder. 2.0 Kit Contents

More information

3M Mechanical Shearbolt Connectors, QCI Series

3M Mechanical Shearbolt Connectors, QCI Series M Mechanical Shearbolt Connectors, QCI Series Data Sheet November 2011 Description Connector Contents M Mechanical Shearbolt Connectors, QCI Series are designed to cover a wide range of conductor sizes

More information

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-Tape/LC

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-Tape/LC 3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-Tape/LC For Tape Shield or Longitudinally Corrugated (LC) Shielded Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350

More information

Data Sheet July For RoHS information, please visit

Data Sheet July For RoHS information, please visit Data Sheet July 2017 3M Cable Ties are molded from 6/6 nylon and are available in a variety of sizes and styles, including weather resistant black for outdoor use. Agency Approvals & Self Certifications

More information

3 Reenterable Encapsulated PST Dome Closure

3 Reenterable Encapsulated PST Dome Closure 3 Reenterable Encapsulated PST Dome Closure Instructions July 1998 34-7037-1080-5-B 1 Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 PST Closure Capacity...3 4.0 Cable Preparation...4 5.0 Bonding and

More information

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-TOW/WOT

3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-TOW/WOT 3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-TOW/WOT For Tape-Over-Wire (TOW) or Wire-Over-Tape (WOT) Shielded Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350

More information

3M Cold Shrink QT-III Silicone Rubber Termination

3M Cold Shrink QT-III Silicone Rubber Termination 3M Cold Shrink QT-III Silicone Rubber Termination For Tape-Over-Wire (TOW) or Wire-Over-Tape (WOT) Shielded Cable 7673-S-8(S)-TOW/WOT Instructions IEEE Std. No. 48 Class 1 Termination 69 kv Class, 350

More information

Branch Splice QS-2001B

Branch Splice QS-2001B Branch Splice QS-2001B Data Sheet 1. Product Description The 3M Branch Splice QS-2001B molded rubber splice kits are designed to connect extruded dielectric power cables rated 15 kv. The basic kits handle

More information

COYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications

COYOTE Dome Closure 9.5 x 28 with Transition Tray for High Density Splice Applications OCTOBER 2017 COYOTE Dome Closure 9.5" x 28" with Transition Tray for High Density Splice Applications Be sure to read and completely understand this procedure before applying product. Be sure to select

More information

Cold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions

Cold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions Cold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions Class I Indoor Termination Voltage Designation: 12/20(24) kv Kit Contents: 1 HeatShrinkBreakoutBootAssembly 3 HeatShrinkBindingSleeves

More information

3M Cable Ties Product Guide. Made in USA. & Plenum Rated

3M Cable Ties Product Guide. Made in USA. & Plenum Rated 3M Cable Ties Product Guide Made in USA & Plenum Rated A new line of general use cable ties from 3M Made in USA These ties are made of high quality 6/6 nylon in the USA, which offers excellent availability

More information

SLiC Aerial Closures

SLiC Aerial Closures 3 SLiC Aerial Closures 1 The 3M SLiC Closure is a singlepiece aerial closure easily installed in construction or maintenance situations. The one piece construction permits complete splice access after

More information

Fiber Splice Panel Rack Mount User Manual

Fiber Splice Panel Rack Mount User Manual Fiber Splice Panel Rack Mount User Manual Content Page INTRODUCTION... 1 Revision History... 1 List of Changes... 1 Trademark Information... 2 Admonishments... 2 1. DESCRIPTION... 2 A. Product Definition

More information

Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application. 5 NOVEMBER 2010 COYOTE Dome 9.5 x 28 Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application. 1. 7. 2. 4. 10.

More information

Model 1100B CHG Terminator. Installation Instructions

Model 1100B CHG Terminator. Installation Instructions Model 1100B CHG Terminator Installation Instructions 1 Contents: 1.0 Safety Information... 3 2.0 Set-up and Adjustments... 3 3.0 Ram Adjustments... 10 4.0 Wire Termination Quality... 12 5.0 General Maintenance...

More information

COYOTE 9.5" x 19" (292 mm x 509 mm) Dome Closure

COYOTE 9.5 x 19 (292 mm x 509 mm) Dome Closure AUGUST 2012 COYOTE 9.5" x 19" (292 mm x 509 mm) Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series

3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series 3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series Data Sheet 1. Product Description 3M Cold Shrink Termination Kit QT-III 7672-S-8 Series contains one silicone rubber termination

More information

3M Cold Shrink 3-Conductor Inline Splice Kits QS-III 5786A- MT, 5787A-MT and 5788A-MT 25/28 kv for use with Armored and Non- Armored 3/C Cable

3M Cold Shrink 3-Conductor Inline Splice Kits QS-III 5786A- MT, 5787A-MT and 5788A-MT 25/28 kv for use with Armored and Non- Armored 3/C Cable 3M Cold Shrink 3-Conductor Inline Splice Kits QS-III 5786A- MT, 5787A-MT and 5788A-MT 25/28 kv for use with Armored and Non- Armored 3/C Cable Data Sheet September 2010 Description 3M Cold Shrink 3-Conductor

More information

COYOTE 28" GLC (Ground Level Closure) Complete Assembly Installation

COYOTE 28 GLC (Ground Level Closure) Complete Assembly Installation NOVEMBER 2016 COYOTE 28" GLC (Ground Level Closure) Complete Assembly Installation Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED

More information

Cold Shrink Silicone Rubber Termination QT-III (With High-K Stress Relief)

Cold Shrink Silicone Rubber Termination QT-III (With High-K Stress Relief) Cold Shrink Silicone Rubber Termination QT-III (With High-K Stress Relief) Instruction Sheet IEEE Std. No. 48 1990 Class 1 Termination 5/8.7 kv Class 95 kv BIL Kit Contents: 3 Hi K, Tracking Resistant,

More information

3M Pleated Foil I/O Cable Assemblies MDR Series

3M Pleated Foil I/O Cable Assemblies MDR Series Mates with standard 3M MDR Boardmount Headers Pleated copper foil provides a 360 degree shield Overmolded Assemblies Available in 68, 80 and 100 Positions Molded-in strain relief Can utilize either #4-40

More information

3M Mini D Ribbon (MDR) Cable Assembly.050 High Speed Video Data Transmission System, 50 Position 14X50-SZWB-XXX-0NC

3M Mini D Ribbon (MDR) Cable Assembly.050 High Speed Video Data Transmission System, 50 Position 14X50-SZWB-XXX-0NC (MDR) Assembly Supports LVDS Channel Link signaling 20 shielded pairs (100 ohm) +4 drains for high bandwidth applications High density 50 position MDR with rugged ribbon type contact 3 Unshielded Twisted

More information

3M Products for Electrical Networks Wind Farm Capabilities. Leading Edge. Electrical Solutions for. Wind Farms

3M Products for Electrical Networks Wind Farm Capabilities. Leading Edge. Electrical Solutions for. Wind Farms 3M Products for Electrical Networks Wind Farm Capabilities Leading Edge Electrical Solutions for Wind Farms 3M technologies for wind farms Wind farm projects are difficult enough without the risk of construction

More information

3M Cold Shrink 1/C Transition Splice Kit QS-III, 5510A-1T-PILC Series

3M Cold Shrink 1/C Transition Splice Kit QS-III, 5510A-1T-PILC Series 3M Cold Shrink 1/C Transition Splice Kit QS-III, 5510A-1T-PILC Series Data Sheet March 2011 Description 3M Cold Shrink 1/C Transition Splice Kits QS-III, 5510A-1T-PILC Series (which includes 5513A-1T-PILC,

More information

3M Cold Shrink QS-III Inline Splice Kits 15 kv 5513A, 5514A, 5515A and 5516A

3M Cold Shrink QS-III Inline Splice Kits 15 kv 5513A, 5514A, 5515A and 5516A 3M Cold Shrink QS-III Inline Splice Kits 15 kv Data Sheet June 2014! CAUTION Working around energized high-voltage systems may cause serious injury or death. Installation should be performed by personnel

More information

MARCH COYOTE 9.5 x 19 (292 mm x 509 mm) Terminal Dome Closure Kits

MARCH COYOTE 9.5 x 19 (292 mm x 509 mm) Terminal Dome Closure Kits MARCH 2012 COYOTE 9.5 x 19 (292 mm x 509 mm) Terminal Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before

More information

FOSC-400D5 INSTALLATION INSTRUCTION. Fibre Optic Splice Closure with integrated organiser system

FOSC-400D5 INSTALLATION INSTRUCTION. Fibre Optic Splice Closure with integrated organiser system FOSC-400D5 INSTALLATION INSTRUCTION Fibre Optic Splice Closure with integrated organiser system 1 General 1.1 The installation instruction describes the necessary steps to install the FOSC-400D5. The

More information

COYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure

COYOTE 9.5 x 19 (292 mm x 509 mm) Cross-Connect Dome Closure AUGUST 2013 COYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED TM product

More information

COYOTE CLOSURE ADOBE SERIES FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (152.4 mm x mm mm x 558.

COYOTE CLOSURE ADOBE SERIES FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0 x 22 8.5 x 22 (152.4 mm x mm mm x 558. FEBRUARY 2000 COYOTE CLOSURE ADOBE SERIES FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (152.4 mm x 558.8 mm 215.9 mm x 558.8 mm) Be sure to read and completely understand this procedure

More information

DOCUMENT OBSOLETE. 3M710 UniPresser for 25-Pair Modular Splicing. Instructions. April B

DOCUMENT OBSOLETE. 3M710 UniPresser for 25-Pair Modular Splicing. Instructions. April B 3710 UniPresser for 25-Pair odular Splicing Instructions D LT April 2001 Table of Contents Parts and Nomenclature.........................................2 Field aintenance Kit..........................................3

More information

3M Cold Shrink QT-III Silicone Rubber Indoor Tubular Termination Kit

3M Cold Shrink QT-III Silicone Rubber Indoor Tubular Termination Kit 3M Cold Shrink QT-III Silicone Rubber Indoor Tubular Termination Kit With High-K Stress Relief For Tape Shield, Wire Shield and UniShield Cable 7622-T-110, 7624-T-110, 7625-T-110, 7626-T-110 Instructions

More information

3M Cold Shrink QT-III Silicone Rubber Indoor Termination Kits With High-K Stress Relief

3M Cold Shrink QT-III Silicone Rubber Indoor Termination Kits With High-K Stress Relief 3M Cold Shrink QT-III Silicone Rubber Indoor Termination Kits With High-K Stress Relief For Tape Shield, Wire Shield and UniShield Cable 7621-T-95, 7622-T-95, 7624-T-95, 7625-T-95 Instructions IEEE Std.

More information

3M Cold Shrink QT-lll Silicone Rubber Skirted Termination Kit 7692-S-4, 7693-S-4, 7694-S-4, 7695-S-4, 7696-S-4

3M Cold Shrink QT-lll Silicone Rubber Skirted Termination Kit 7692-S-4, 7693-S-4, 7694-S-4, 7695-S-4, 7696-S-4 3M Cold Shrink QT-lll Silicone Rubber Skirted Termination Kit 7692-S-4, 7693-S-4, 7694-S-4, 7695-S-4, 7696-S-4 With High-K Stress Relief For Tape Shielded, Wire Shielded and UniShield Cable Instructions

More information

OFE-CLS-Type Outside Plant (OSP) Fiber Optic Closures Instructions

OFE-CLS-Type Outside Plant (OSP) Fiber Optic Closures Instructions Instruction Sheet 860385855 Issue 3, June 2013 Uniprise Solutions OFE-CLS-Type Outside Plant (OSP) Fiber Optic Closures Instructions General Uniprise OFE-CLS-Type Outside Plant (OSP) Fiber Optic Closures

More information

FOSC-400A4 INSTALLATION INSTRUCTION

FOSC-400A4 INSTALLATION INSTRUCTION FOSC-400A4 INSTALLATION INSTRUCTION TC-441-IP Rev A, Mar 2017 www.commscope.com Fibre Optic Splice Closure with integrated organiser system 1 General 1.1 The installation instruction describes the necessary

More information

3M Textool Test and Burn-In Sockets for 1.0 mm Area Array Packages Including Ball Grid Array and Land Grid Array

3M Textool Test and Burn-In Sockets for 1.0 mm Area Array Packages Including Ball Grid Array and Land Grid Array 3M Textool Test and Burn-In Sockets for 1.0 mm Area Array Packages Including Ball Grid Array and Land Grid Array 1.0 mm Pitch Socket Platforms Socket Max. Package Maximum Max. Pin Lid Series Product Number

More information

JANUARY 2015 NOMENCLATURE. TOOLS REQUIRED 3/8" & 7/16" Can wrench or socket 1/4 Nut driver or screwdriver Snips Fiber optic cable opening tools

JANUARY 2015 NOMENCLATURE. TOOLS REQUIRED 3/8 & 7/16 Can wrench or socket 1/4 Nut driver or screwdriver Snips Fiber optic cable opening tools JANUARY 2015 COYOTE Dome Closure 6-1/2" x 17" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED TM product before application. 1 2

More information

QT-III Cold Shrink Silicone Rubber

QT-III Cold Shrink Silicone Rubber QT-III Cold Shrink Silicone Rubber 7600-T-3RJS Series 3/C Cabinet Termination Instructions Kit Contents: 3ÑSilicone Rubber Phase Re-jacketing Sleeve Assembly 3ÑCold Shrink Silicone Rubber Termination Assembly

More information

COYOTE Dome Closure 6.5" x 22" Kits. COYOTE Dome Closure 6.5" x 22" for Buffer Tube Applications. Includes: (2) Grommets, (1) Buffer

COYOTE Dome Closure 6.5 x 22 Kits. COYOTE Dome Closure 6.5 x 22 for Buffer Tube Applications. Includes: (2) Grommets, (1) Buffer JANUARY 2015 COYOTE Dome Closure 6.5" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application. 1 2 3 6

More information

SJOF-BS604A Fiber Optic Splice Closure User Manual Rev.0

SJOF-BS604A Fiber Optic Splice Closure User Manual Rev.0 Fiber Optic Splice Closure VISSEM 1. Introduction 1.1 General VISSEM s SJOF-BS604A protects fiber optic splicing point in various installation conditions such as aerial, manholes, ducts, wall and direct

More information

3M Cold Shrink QT-II Silicone Rubber Indoor Termination Kits

3M Cold Shrink QT-II Silicone Rubber Indoor Termination Kits 3M Cold Shrink QT-II Silicone Rubber Indoor Termination Kits With High-K Stress Relief For Tape Shield, Wire Shield and UniShield Instructions IEEE Std. No. 48 Class 1 Termination 8 kv Class, 95 kv BIL:

More information

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit 3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief For Tape Shielded, Wire Shielded and UniShield Cable 7685-S-8 Instructions IEEE Std. No. 48 Class 1 Termination 35

More information

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kits

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kits 3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kits With High Ampacity Ground Connection and High-K Stress Relief For Tape Shield, Wire-Over-Tape Shield and Longitudinally Corrugated (LC) Shield

More information

3M Cold Shrink QT-III Silicone Rubber Termination Kits 7640-T and 7650-T Series 5, 8, 15, 25/28 and 35 kv

3M Cold Shrink QT-III Silicone Rubber Termination Kits 7640-T and 7650-T Series 5, 8, 15, 25/28 and 35 kv 3M Cold Shrink QT-III Silicone Rubber Termination Kits 7640-T and 7650-T Series 5, 8, 15, 25/28 and 35 kv Data Sheet September 2014 Description 3M Cold Shrink QT-III Silicone Rubber Termination Kits, 7640-T

More information

FIST-GSS2 FIST-GSS3. Fist Generic Splicing Shelf. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails

FIST-GSS2 FIST-GSS3. Fist Generic Splicing Shelf. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails FIST-GSS2 FIST-GSS3 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 3 Installation of the shelf 3.1 Mounting the shelf

More information

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief 3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief 7642-S-2, 7642-S-2(L) For Jacketed Concentric Neutral (JCN) and Concentric Neutral (CN) Cable Instructions IEEE Std.

More information

SYSTIMAX G2 4U Fixed Rear Access Combination Shelf Instructions

SYSTIMAX G2 4U Fixed Rear Access Combination Shelf Instructions Instruction Sheet 860452176 SYSTIMAX Solutions SYSTIMAX 360 360G2 4U Fixed Rear Access Combination Shelf Instructions General The SYSTIMAX 360 360G2 4U rear access fiber optic combination shelf mounts

More information

COYOTE Terminal Dome Closure 6.5" x 22"

COYOTE Terminal Dome Closure 6.5 x 22 FEBRUARY 2015 COYOTE Terminal Dome Closure 6.5" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

Fiber Connector Shelf (CCS)

Fiber Connector Shelf (CCS) Corning Cable Systems Standard Recommended Procedure (SRP) 003-595 Issue 3, May 2007 Page 1 of 6 Fiber Connector Shelf (CCS) Table of Contents 1. General... 1 2. Precautions... 1 3. Components... 2 4.

More information

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System Instruction Sheet SRSR SERIES Rotating Sliding Rail System THANK YOU Thank you for purchasing the SRSR Series Rotating Sliding Rail System. Please read these instructions thoroughly before assembling this

More information

OPTICAL FIBER CLOSURE

OPTICAL FIBER CLOSURE OPTICAL FIBER CLOSURE INSTALLATION MANUAL STC-HTM Read these instructions carefully and completely before beginning installation. For assistance, contact Technical Support at 82.61.373.7500(South Korea),

More information

GM Specification Annual Test Data

GM Specification Annual Test Data GM Specification Annual Test Data GM Specification Annual Test Data Technical Bulletin The 3M IATD Quality Laboratory tested the following tapes to the Automotive Specification. The results of the testing

More information

Instructions for Use - Opt-X 1000i Enclosure

Instructions for Use - Opt-X 1000i Enclosure 5R1UM-F03, 5R1UM-S03, 5R2UM-F06, 5R2UM-S06, 5R3UM-F09, 5R3UM-F12, 5R4UM-F12, 5R4UM-F15 Instructions for Use - Opt-X 1000i Enclosure 5R1UM-*03 5R2UM-*06 5R3UM-F** 5R4UM-F** Page 1 of 8 Leviton Network Solutions,

More information

GM Specification Annual Test Data

GM Specification Annual Test Data GM Specification Annual Test Data GM Specification Annual Test Data Technical Bulletin The 3M IATD Quality Laboratory tested the following tapes to the Automotive Specification. The results of the testing

More information

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit

3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit 3M Cold Shrink QTIII Silicone Rubber Skirted Termination Kit With HighK Stress Relief 3M Cold Shrink QTIII Silicone Rubber Skirted Termination Kit With HighK Stress Relief For Jacketed Concentric Neutral

More information

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION

OFS 400A FIBER OPTIC INTERCONNECT Instruction Sheet UNIT (FOIU) Comcode INSTALLATION OFS 400A FIBER OPTIC INTERCONNECT 636-299-109-01 Instruction Sheet UNIT (FOIU) Comcode 846 586 212 INSTALLATION This instruction sheet covers the 400A1 (106266901) and 400A2 (106414170) Fiber Optic Interconnect

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TABLE OF CONTENTS GENERAL...2 SPECIFICATIONS...2 PACKAGE CONTENTS...2 PACKAGE CONTENTS: ACCESSORIES...3 REQUIRED TOOLS...3 ADD-ON COMPONENTS...3 CLOSURE MOUNTING...3 LOCK AND UNLOCK EXTERIOR DOOR...3 CABLE

More information

Volition. VF-45 Quick Install kit. and Maintenance Cleaning Kit. 3Innovation

Volition. VF-45 Quick Install kit. and Maintenance Cleaning Kit. 3Innovation Volition VF-45 Quick Install Kit and Maintenance Cleaning Kit O b D s oc ol e um te en t COOL HAND TOOLS. VF-45 Quick Install kit Get your hands on a VF-45 Quick Install Kit from 3M and you will have everything

More information

Cold Shrink QS T Trifurcating Transition Splice Kit

Cold Shrink QS T Trifurcating Transition Splice Kit Cold Shrink QS2012-13-3T Trifurcating Transition Splice Kit Instructions IEEE Std. 404-1993 15 kv Class 110 kv BIL Completed Splice Cable Size Range Requirements PILC 500 kcmil Conductor Size (240 mm 2

More information

Section 3 FIBERLIGN Closure Series

Section 3 FIBERLIGN Closure Series FIBERLIGN Closure Series: Section 3 Section 3 FIBERLIGN Closure Series Table of Contents Page FIBERLIGN s...3-2 FIBERLIGN Organizers...3-3 FIBERLIGN UNI-CLOSURE...3-8 FIBERLIGN Fiber Safe...3-11 FIBERLIGN

More information

12-Inch Hybrid Fiber Access Terminal Installation Instructions

12-Inch Hybrid Fiber Access Terminal Installation Instructions 12-Inch Hybrid Fiber Access Terminal Installation Instructions 19683-A Content Page 1 PRODUCT DESCRIPTION.................................................................. 2 2 PRODUCT FUNCTION.....................................................................

More information

Features: Use the selection chart below to choose the Splice Case and splice tray organizer which meet the requirements for your application.

Features: Use the selection chart below to choose the Splice Case and splice tray organizer which meet the requirements for your application. FIBERLIGN Organizers For s (Protected and ) and Mechanical s FIBERLIGN Fiber Optic Organizers are designed to help organize, secure, support and protect delicate optical fibers before, during and after

More information

Fiber optic splice closure

Fiber optic splice closure FOSC-450A I N S T A L L A T I O N I N S T R U C T I O N TC-772-IP Rev A, Mar 2017 www.commscope.com Fiber optic splice closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories

More information

Environmental Distribution Center (EDC-06P-NH)

Environmental Distribution Center (EDC-06P-NH) Corning Cable Systems Standard Recommended Procedure (SRP) 003-545 Issue 4, July 2004 Page 1 of 13 Environmental Distribution Center (EDC-06P-NH) 1.2 To purchase any accessories that are sold separately,

More information

LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions

LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions ADCP-92-129 Issue 1 6/2010 Content Page INTRODUCTION.............................................................................

More information

3M Cold Shrink QT-lll Silicone Rubber Indoor Tubular Termination Kits With High-K Stress Relief

3M Cold Shrink QT-lll Silicone Rubber Indoor Tubular Termination Kits With High-K Stress Relief 3M Cold Shrink QTlll Silicone Rubber Indoor Tubular Termination Kits With HighK Stress Relief For Tape Shield, Wire Shield and UniShield Cable 7693T150, 7695T150, 7696T150 Instructions IEEE Std. No. 48

More information

Pretium Wall-Mountable Housing (PWH-02P/-04P/- 06P/-12P and FZB-02P-JB)

Pretium Wall-Mountable Housing (PWH-02P/-04P/- 06P/-12P and FZB-02P-JB) 1. Precautions 2. Carton Contents Pretium Wall-Mountable Housing OR Fiber Zone Box (FZB-02P-JB) PWH-02P and FZB-02B-JP have: (15 inches) edge grommet (1) Laser warning label (2) Fiber identification labels

More information

QS-III. 5513A, 5514A, 5515A and 5516A 15 kv Cold Shrink Inline Splice Kits. Data Sheet CAUTION. 1. Product Description. 2. Applications.

QS-III. 5513A, 5514A, 5515A and 5516A 15 kv Cold Shrink Inline Splice Kits. Data Sheet CAUTION. 1. Product Description. 2. Applications. QS-III 5513A, 5514A, 5515A and 5516A 15 kv Cold Shrink Inline Splice Kits Data Sheet Tape Shield Wire Shield UniShield Kit Contents: 1 Cold Shrink Silicone Rubber Splice Body 1 Cold Shrink Adapter Tube

More information

LSS1U-144/7 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL CUSTOMER SERVICES REFERENCES TOOLS REQUIRED

LSS1U-144/7 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL CUSTOMER SERVICES REFERENCES TOOLS REQUIRED OFS Fitel LSS1U-144/7 Fiber Optic 636-99-103-1 Instruction Sheet Splice Shelf Installation COMCODE 845 866 474 LSS1U-144/7 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL This instruction sheet provides

More information

FIST-GSS2. Fist Generic Splicing Shelf MK2. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails

FIST-GSS2. Fist Generic Splicing Shelf MK2. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails FIST-GSS2 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf MK2 Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Optional extra s 3 Installation of the shelf 3.1

More information

3M Three-Wall and Four-Wall Headers. Series 3XXX

3M Three-Wall and Four-Wall Headers. Series 3XXX 1 of 7 M Three-Wall and Four-Wall Headers Series XXX Product 78-10-0008-0 Released: 0-0-11 of 7 Table of Contents Section Page 1. Scope........ M Customer Documents....... Performance and Test Descriptions...

More information

3000SC Fiber Optic Splice Closure

3000SC Fiber Optic Splice Closure 3000SC Fiber Optic Splice Closure Protect All Of Your Fiber Optic Splices From Harsh Outside Plant Environments Product Description Our 3000SC Fiber Optic Splice Closure is a sealed, reinforced thermoplastic

More information

FIST-GMS2. FIST Generic Mixed Shelf MK2. Contents. 1 Introduction. 5 Termination of the pigtails. 2 General. 6 Splicing + fiber storage

FIST-GMS2. FIST Generic Mixed Shelf MK2. Contents. 1 Introduction. 5 Termination of the pigtails. 2 General. 6 Splicing + fiber storage FIST-GMS2 I N S T A L L A T I O N I N S T R U C T I O N FIST Generic Mixed Shelf MK2 Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Optional extra s 3 Installation of the shelf 3.1 Mounting

More information

3M Electrical Tapes Product Selection Guide. Insulate & Protect. with Quality Tapes. Preliminary

3M Electrical Tapes Product Selection Guide. Insulate & Protect. with Quality Tapes. Preliminary 3M Electrical Tapes Product Selection Guide Insulate & Protect with Quality Tapes Get your hands on 3M Tape! 3M now offers new and experienced electricians a chance to sharpen their skills with the complete

More information

COYOTE Dome Cross-Connect Closure 6-1/2" x 22"

COYOTE Dome Cross-Connect Closure 6-1/2 x 22 FEBRUARY 2015 COYOTE Dome Cross-Connect Closure 6-1/2" x 22" Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED product before application.

More information

Door Edge Protection Film 36 inch

Door Edge Protection Film 36 inch Door Edge Protection Film 36 inch Technical Data Sheet June, 2013 3M Part No.(s) PN 3M Part Descriptor(s) Door Edge Protection Film 36 inch Product Description 3M Door Protection Film is a super tough

More information

FIBER CONNECTOR SAFETY WARNINGS

FIBER CONNECTOR SAFETY WARNINGS FIBER CONNECTOR SAFETY WARNINGS SAFETY INFORMATION 1. Always wear safety glasses. 2. Isopropyl alcohol is flammable and may cause eye irritation. In case of contact with eyes, flush with water for at least

More information