Dept. Of Electrical Power Engineering, FKEE, University Tun Hussein Onn Malaysia P.O Box , Parit Raja, Batu Pahat, Johor, Malaysia

Size: px
Start display at page:

Download "Dept. Of Electrical Power Engineering, FKEE, University Tun Hussein Onn Malaysia P.O Box , Parit Raja, Batu Pahat, Johor, Malaysia"

Transcription

1 Parameter Sensitivity Study for Optimization of 1Slot-8Pole Three- Phase Wound Field Switched-Flux Machine Faisal Khan a, Erwan Sulaiman b, Md Zarafi Ahmad c and Zhafir Aizat d Dept. Of Electrical Power Engineering, FKEE, University Tun Hussein Onn Malaysia P.O Box. 8, Parit Raja, Batu Pahat, Johor, Malaysia a faisalkhan@ciit.net.pk, b erwan@uthm.edu.my, c zarafi@uthm.edu.my, d zhafiraizat9@gmail.com Keywords: Switched-Flux machine, deterministic optimization, finite element analysis, robust rotor, non-overlap windings Abstract. This paper presents parameter sensitivity study and performance analysis of 1Slot-8Pole three-phase wound field switched-flux machine (WFSFM). The proposed machine consists of armature slots, field-excitation coil (FEC) slots and 8 rotor poles. All active parts such as armature coil and FEC are located on the stator, while the rotor part consists of only single piece iron. This makes the machine becoming more robust and more suitable to be apply for high speed motor drive system applications. The deterministic design optimization approach is used to treat several design parameters defined in rotor, armature and FEC slot area to achieve better results than initial design. -D finite element analysis (FEA) is used to study various characteristics of machine. Since the initial design fail to attain the maximum torque and power, therefore the performance of machine is enhanced by refinement of several design parameters. After design refinement, WFSFM has achieved the maximum torque of.3 Nm and power of.7 kw at maximum field current density, J e of 3 A/mm and armature current density, J a of 3A rms /mm which is approximately 3 times the torque and times the power of initial design. Introduction In the mid 19s, the first concept of switched-flux machine (SFM) has been founded and printed. stator slots and rotor poles (S-P) permanent magnet (PM) SFM i.e. permanent magnet single-phase limited angle actuator or more well-known as Laws relay has been developed [1], and then single phase generator with stator slots, and or rotor poles (S-/P) has been invented []. Over the last decade, many SFM topologies have been introduced for various application i.e. automotive, domestic appliances, aerospace etc. SFM can be classified into three groups that are Permanent Magnet (PM) SFM, Field Excitation (FE) SFM and Hybrid Excitation (HE) SFM. Permanent magnet and field winding are the main sources of flux in PMSFM and FESFM while in HESFM, both field winding and permanent magnet produces the flux [3-]. In all these SFMs the armature winding and field winding or Permanent magnets are located on the stator. When compare with other SFMs, the FESFM motor has advantages of low cost, simple construction, magnet-less machine, and variable flux control capabilities suitable for various performances. Furthermore, to manufacture the FESFM motors, the PM on the stator of conventional PMSFMs is replaced by DC field excitation coil. In other words, the FESFM motors having salient-rotor structure is a novel topology, merging the principles of the SRMs and inductor generator [-7]. The performance of SFM is enhanced by using segmental rotor configuration in recent research [8]. Segmental rotor is designed in a manner such that to achieve bipolar flux in armature winding, which has neither magnets nor winding. To produce bipolar flux linkages in this way, a toothedrotor structure may be used but it requires overlap windings on the stator [9]. Non-overlap winding has been used in [1] to increase the efficiency by reducing the copper losses and enhanced the speed torque characteristics of SFM. A three-phase SFM using a segmental rotor has been proposed in [11] to improve fault tolerance to a reduction in torque pulsations and power converter rating per

2 phase. Fig. 1 [9] and [11] shows SMFs having segmented-rotor with non-overlap winding and toothed-rotor with overlap winding at the stator. A single-phase WFSFM machine was comprehensively investigated in [1]. In that machine, armature and field windings are fully pitched and hence the end-winding is long. Two single phase WFSFMs topologies with DC field and AC armature windings having the same coil-pitch of slot-pitches and having different coil-pitches of 1 and 3 slot-pitches respectively are discussed [13]. It is shown that the iron loss and copper loss of WFSFM has been reduced and thus increased the efficiency but it has problem of unbalanced magnetic force. As one alternative to overcome these problems, a new structure of initial design of 1Slot-8Pole three-phase WFSFM with non-overlap armature and field windings is proposed as shown in Fig. 3. From the figure, it is clear that the motor consists of FEC and armature coil located at the stator. The rotor is made of single piece of iron, becoming more robust and more suitable for high speed applications. Based on the topology of 1Slot-8Pole WFSFM illustrated in Fig. 3, design optimization is conducted based on sensitivity of seven design parameters to get maximum performance. This paper compares the performance analysis of initial design and improved design of 1Slot-8Pole WFSFM having toothed-rotor structure and non-overlap armature and field windings. Design specification of proposed 1Slot-8Pole WFSFM The design specifications of proposed 1Slot-8pole WFSSFM are listed in Table 1. The selection of initial design parameters is based on the following assumptions: the initial rotor radius selected is approximately % to 7 % of total machine radius; the FEC slot area and armature coil slot area are set to be trapezoidal shape with same slot area. 8mm 1mm FEC FEC Armature coil mm Rotor Armature coil Fig. 1 Three-phase WFSFM with overlap windings Fig. Three-phase WFSFM with non-overlap windings Fig. 3 Initial design of 1Slot-8Pole Table 1. Initial Design Parameters of 1Slot-8Pole Parameters Values Stator radius [mm] 7 Rotor radius [mm] Air gap length [mm].3 Stator pole width [mm] 8 Armature Slot Area [mm ] 3.11 FEC Slot Area [mm ] 3.11 Field Excitation current [A] Armature current [A] FEC turns Armature coil turns Filling factor. Stack length[mm] 7 Stator

3 Design parameters variation procedures The performance analyses of initial design of 1Slot-8Pole WFSFM are investigated. The torque and power obtained are 7. Nm and.9 kw at maximum speed of 31.7 rev/min, which is far from the target requirements. To achieve the requirements, design free parameters X1 to X7 are defined in rotor and stator part as shown in Fig.. Deterministic optimization approach is used to find the maximum performance of machine by adjusting the design free parameters X1 to X7 while keeping the air gap constant. Variation of rotor parameters. The first step is to change the rotor parameters X1, X and X3 while keeping X to X7 constant. Since the torque increases with the increases in rotor radius, X1 is treated and considered as dominant parameter to improve the torque. The torque has maximum value of 1.93Nm when the rotor radius is mm as shown in Fig.. Then keeping X1 at mm, the rotor pole depth X and rotor pole width X3 are adjusted, illustrated in Fig. and achieved the maximum torque. Variation of Armature coil and FEC parameters: Once the maximum torque for X and X3 are determined, the second step is done by changing the armature slot parameters width, X and depth, X while keeping the rotor parameters and FEC slot area constant to get maximum torque, as plotted in Fig. 7. Finally, FEC slot area (width, X and depth, X7) is changed by keeping the other parameters constant for better torque. Fig. 8 shows that maximum torque of 1.1Nm is achieved after completion of 1 st cycle and then,.3nm after completion of nd cycle. The design method above is treated repeatedly by changing X1 to X7 until maximum torque and power are achieved. The final design of this machine which produced the maximum torque and power is shown in Fig. 9. The comparison between the initial and final design parameters are listed in Table. X7 X T[Nm] 1 1 nd cycle Rotor X X3 X Stator Rotor pole width, X3[mm] Fig. Design parameters of 1Slot-1Pole WFSalR SFM X1 nd cycle X. 7.. Rotor radius, X1 [mm] Fig. Torque versus rotor radius Fig. Torque versus rotor pole width 1 1 nd cycle 18 Armature depth, X [mm] Fig.7 Torque versus armature slot depth

4 1mm 1 1 nd cycle 1mm 1mm FEC depth, X7 [mm] mm Fig.8 Torque versus FEC slot depth Fig. 9 Improved design of 1Slot-8Pole WFSFM Improvement of various characteristics of 1Slot-8Pole WFSFM Cogging Torque. The cogging torque analyses for both designs are shown in Fig. 1. The initial design of 1Slot-8Pole WFSFM has high peak to peak cogging torque of approximately 7 Nm. As high cogging torque causes vibration in machine and makes it noisy, therefore by following various steps of changing the design parameters, the cogging torque of 1Slot-8Pole WFSFM is reduced to approximately Nm. Torque and Power versus speed characteristics. The torque and power versus speed curves of initial and improved design of 1Slot-1Pole WFSFMs are plotted in Fig. 11 and 1. At the base speed of 31.7 rev/min and.7 rev/min, the maximum torque of 7.1 Nm and.3 Nm is obtained and torque starts to decrease if the machine is operated beyond the base speed. The power accomplished by initial design of 1Slot-8Pole WFSFM at base speed is.9 kw and starts to reduce until 1.1 kw at higher speed of 8.8 rev/min due to increase in iron loss while the power Electrical cycle [Degrees] Fig.1 Cogging Torque P [kw] Initial design Improved design 8 Speed [rev/m] Fig.11 Torque and power vs. speed for initial design P[kW] 8 Speed [rev/min] Fig.1 Torque and power vs. speed for improved design Table. Initial and Improved Design Parameters of 1Slot- 8Pole WFSalR SFM Parameters Initial Improved X1 Rotor radius [mm] X Rotor depth [mm] X3 Rotor pole width [mm] 1 X Armature coil width [mm] 13 1 X Armature coil depth [mm] 1.. X FEC width [mm] X7 FEC depth [mm] Ag Air gap length [mm].3.3 S a Armature coil slot area[mm ] S fec FEC slot area [mm ] T Average torque [Nm] 7..3 P Power [kw].9.7

5 achieved by improved design is.7 kw at maximum torque and base speed of.7 rev/min. Conclusion In this paper, parameter sensitivity study for design optimization and performance analysis of 1Slot-8Pole are presented and clearly demonstrated. The proposed design has a robust rotor structure and non-overlap windings. As a result the motor can be used for high speed applications and efficiency will increase due to reduction of copper losses. The shape of the proposed motor is very simple which paves better way of design optimization compared to other machines. The torque and power are increased to an acceptable condition by design refinement. Further optimization techniques will be applied in future to reduce the cogging torque and increase the flux linkage, average torque and power. References [1] Laws AE. An electromechanical transducer with permanent magnet polarization, Technical Note No.G.W., Royal Aircraft Establishment, Farnborough, UK, 19 [] Rauch SE, Johnson LJ., Design principles of flux-switching alternators, AIEE Trans., 7 (19) [3] F.Khan, E. Sulaiman, M.Z. Ahmad, Coil test analysis of wound-field three-phase flux switching machine with non-overlap winding and salient rotor, IEEE 8th International Power Engineering and Optimization Conference (PEOCO), (1) 3-7. [] Sulaiman E, Kosaka T, Matsui N., Design optimization and performance of a novel -slot - pole PMFSM with hybrid excitation for hybrid electric vehicle, IEEJ Trans. Ind. Appl., 13 (1) [] E. Sulaiman, M. Z. Ahmad, T. Kosaka, and N. Matsui, Design Optimization Studies on High Torque and High Power Density Hybrid Excitation Flux Switching Motor for HEV, Procedia Engineering, 3(13) [] J. H. Walker, The theory of the inductor alternator, J. IEE, 89 (19) 7 1. [7] T. J. E. Miller, Switched Reluctance Machines and Their Control, Hillsboro, OH: Magna Physics, [8] B.C. Mecrow, E.A. El-Kharashi, J.W. Finch, and A.G.Jack, Segmental rotor switched reluctance motors with single-tooth windings, IEE Proc. on Power Applications,1(3) [9] Erwan Bin Sulaiman, Takashi Kosaka and Nobuyuki Matsui, Design Study and Experimental Analysis of Wound Field Flux Switching Motor for HEV Applications, XXth International Conference on Electrical Machines (ICEM), (1) [1] A. Zulu, B.C. Mecrow, M. Armstrong, Topologies for three-phase Wound field Segmented- Rotor flux switching Machines th IET International Conference on Power Electronics, Machines and Drives (PEMD), (1) 1- [11] Ackim Zulu, Barrie C. Mecrow, and Matthew Armstrong, A Wound-Field Three-Phase Flux-Switching Synchronous Motor With All Excitation Sources on the Stator, IEEE Transactions on Industry Applications, (1) [1] C. Pollock, H. Pollock, R. Barron, J. R. Coles, D. Moule, A. Court, and R. Sutton, Fluxswitching motors for automotive applications, IEEE Trans. Ind. Appl., () [13] Y. J. Zho, and Z. Q. Zhu, Comparison of low-cost single-phase wound-field switched-flux machines, 13 IEEE International Electric Machines & Drives Conference (IEMDC), (13) 17-18

Performance Comparison of 24Slot-10Pole and 12Slot-8Pole Wound Field Three-Phase Switched- Flux Machine

Performance Comparison of 24Slot-10Pole and 12Slot-8Pole Wound Field Three-Phase Switched- Flux Machine Performance Comparison of 24Slot-10Pole and 12Slot-8Pole Wound Field Three-Phase Switched- Flux Machine Faisal Khan, Erwan Sulaiman, Md Zarafi Ahmad Department of Electrical Power Engineering, Faculty

More information

Comparative Performance of FE-FSM, PM-FSM and HE-FSM with Segmental Rotor Hassan Ali Soomro a, Erwan Sulaiman b and Faisal Khan c

Comparative Performance of FE-FSM, PM-FSM and HE-FSM with Segmental Rotor Hassan Ali Soomro a, Erwan Sulaiman b and Faisal Khan c Comparative Performance of FE-FSM, PM-FSM and HE-FSM with Segmental Rotor Hassan Ali Soomro a, Erwan Sulaiman b and Faisal Khan c Department of Electrical power Engineering, Universiti Tun Hussein Onn

More information

Comparative Study of 24Slot-10Pole and 24Slot- 14Pole Three-Phase Wound Field Salient Rotor Switched-Flux Motor

Comparative Study of 24Slot-10Pole and 24Slot- 14Pole Three-Phase Wound Field Salient Rotor Switched-Flux Motor Comparative Study of 24Slot-10Pole and 24Slot- 14Pole Three-Phase Wound Field Salient Rotor Switched-Flux Motor Faisal Khan, Erwan Sulaiman, Md Zarafi Ahmad, Zhafir Aizat Husin Department of Electrical

More information

Journal of Applied Science and Agriculture

Journal of Applied Science and Agriculture AENSI Journals Journal of Applied Science and Agriculture ISSN 1816-9112 Journal home page: www.aensiweb.com/jasa Design Refinement and Performance Analysis of 12Slot-10Pole Wound Field Salient Rotor Switched-Flux

More information

Design and Analysis of Wound Field Three-Phase Flux Switching Machine with Non-overlap Windings and Salient Rotor

Design and Analysis of Wound Field Three-Phase Flux Switching Machine with Non-overlap Windings and Salient Rotor International Journal on Electrical Engineering and Informatics - Volume 7, Number 2, June 215 Design and Analysis of Wound Field Three-Phase Flux Switching Machine with Non-overlap Windings and Salient

More information

Department of Electrical Power Engineering, Universiti Tun Hussein Onn Malaysia, Locked Bag 101, Batu Pahat, Johor, Malaysia

Department of Electrical Power Engineering, Universiti Tun Hussein Onn Malaysia, Locked Bag 101, Batu Pahat, Johor, Malaysia Performance Comparison of 12S-14P Inner and Field Excitation Flux Switching Motor Syed Muhammad Naufal Syed Othman a, Erwan Sulaiman b, Faisal Khan c, Zhafir Aizat Husin d and Mohamed Mubin Aizat Mazlan

More information

86400 Parit Raja, Batu Pahat, Johor Malaysia. Keywords: Flux switching motor (FSM), permanent magnet (PM), salient rotor, electric vehicle

86400 Parit Raja, Batu Pahat, Johor Malaysia. Keywords: Flux switching motor (FSM), permanent magnet (PM), salient rotor, electric vehicle Preliminary Design of Salient Rotor Three-Phase Permanent Magnet Flux Switching Machine with Concentrated Winding Mahyuzie Jenal 1, a, Erwan Sulaiman 2,b, Faisal Khan 3,c and MdZarafi Ahmad 4,d 1 Research

More information

LOW COST AND ROBUST ROTOR THREE-PHASE WOUND-FIELD SWITCHED-FLUX MACHINES FOR HEV APPLICATIONS

LOW COST AND ROBUST ROTOR THREE-PHASE WOUND-FIELD SWITCHED-FLUX MACHINES FOR HEV APPLICATIONS LOW COST AND ROBUST ROTOR THREE-PHASE WOUND-FIELD SWITCHED-FLUX MACHINES FOR HEV APPLICATIONS Faisal Khan, Erwan Sulaiman, Mohd Fairoz Omar and Hassan Ali Soomro Research Center for Applied Electromagnetics,

More information

Selected paper. Design studies and performance of a novel 12S- 8P HEFSM with segmental rotor

Selected paper. Design studies and performance of a novel 12S- 8P HEFSM with segmental rotor Hassan Ali, Erwan Sulaiman 2, Mohd Fairoz Omar, Mahyuzie Jenal Selected paper Design studies and performance of a novel 12S- 8P HEFSM with segmental JES Journal of Electrical Systems This paper present

More information

Department of Electrical Power Engineering, UTHM,Johor, Malaysia

Department of Electrical Power Engineering, UTHM,Johor, Malaysia Design and Optimization of Hybrid Excitation Flux Switching Machine with FEC in Radial Direction Siti Khalidah Rahimi 1, Erwan Sulaiman 2 and Nurul Ain Jafar 3 Department of Electrical Power Engineering,

More information

INVESTIGATIVE STUDY OF A NOVEL PERMANENT MAGNET FLUX SWITCHING MACHINE EMPLOYING ALTERNATE CIRCUMFERENTIAL AND RADIAL PERMANENT MAGNET

INVESTIGATIVE STUDY OF A NOVEL PERMANENT MAGNET FLUX SWITCHING MACHINE EMPLOYING ALTERNATE CIRCUMFERENTIAL AND RADIAL PERMANENT MAGNET INVESTIGATIVE STUDY OF A NOVEL PERMANENT MAGNET FLUX SWITCHING MACHINE EMPLOYING ALTERNATE CIRCUMFERENTIAL AND RADIAL PERMANENT MAGNET M. Jenal and E. Sulaiman Research Center for Applied Electromagnetics

More information

Design Study of Single PhaseInner-Rotor Hybrid Excitation Flux Switching Motor For Hybrid Electric Vehicles

Design Study of Single PhaseInner-Rotor Hybrid Excitation Flux Switching Motor For Hybrid Electric Vehicles Design Study of Single PhaseInner-Rotor Hybrid Excitation Flux Switching Motor For Hybrid Electric Vehicles Mohamed MubinAizatMazlan,ZhafirAizatHusin Syed Muhammad Naufal Syed Othmanand ErwanSulaiman Department

More information

Performance Analysis of 12S-10P Hybrid-Excitation Flux Switching Machines for HEV

Performance Analysis of 12S-10P Hybrid-Excitation Flux Switching Machines for HEV Performance Analysis of 12S-1P Hybrid-Excitation Flux Switching Machines for HEV Nurul Ain Jafar, Siti Khalidah Rahimi, Siti Nur Umira Zakaria and Erwan Sulaiman, Department of Electrical Power Engineering,

More information

A New Switched Flux Machine Employing Alternate Circumferential and Radial Flux (AlCiRaF) Permanent Magnet for Light Weight EV

A New Switched Flux Machine Employing Alternate Circumferential and Radial Flux (AlCiRaF) Permanent Magnet for Light Weight EV Journal of Magnetics 21(4), 537-543 (2016) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 https://doi.org/10.4283/jmag.2016.21.4.537 A New Switched Flux Machine Employing Alternate Circumferential and

More information

COMPARATIVE STUDY ON A NEW PERMANENT MAGNET FLUX SWITCHING MACHINE CONFIGURATION OVER SEGMENTAL AND SALIENT ROTOR STRUCTURE

COMPARATIVE STUDY ON A NEW PERMANENT MAGNET FLUX SWITCHING MACHINE CONFIGURATION OVER SEGMENTAL AND SALIENT ROTOR STRUCTURE ISSN 1819-668 26-213 Asian Research Publishing Network (ARPN). All rights reserved. www.arpnjournals.com COMPARATIVE STUDY ON A NEW PERMANENT MAGNET FLUX SWITCHING MACHINE CONFIGURATION OVER SEGMENTAL

More information

Design Study and Analysis of Hybrid Excitation Flux Switching Motor with DC Excitation in Radial Direction

Design Study and Analysis of Hybrid Excitation Flux Switching Motor with DC Excitation in Radial Direction Design Study and Analysis of Hybrid Excitation Flux Switching Motor with DC Excitation in Radial Direction E. Sulaiman 1, N. S. M. Amin 1, Z. A. Husin 1, M. Z. Ahmad 1 and T. Kosaka 2 1 Universiti Tun

More information

Design Comparison of Inner and Outer Rotor of Permanent Magnet Flux Switching Machine for Electric Bicycle Application

Design Comparison of Inner and Outer Rotor of Permanent Magnet Flux Switching Machine for Electric Bicycle Application IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Design Comparison of Inner and Outer Rotor of Permanent Magnet Flux Switching Machine for Electric Bicycle Application To cite

More information

INWHEEL SRM DESIGN WITH HIGH AVERAGE TORQUE AND LOW TORQUE RIPPLE

INWHEEL SRM DESIGN WITH HIGH AVERAGE TORQUE AND LOW TORQUE RIPPLE INWHEEL SRM DESIGN WITH HIGH AVERAGE TORQUE AND LOW TORQUE RIPPLE G. Nalina Shini 1 and V. Kamaraj 2 1 Department of Electronics and Instrumentation Engineering, R.M.D. Engineering College, Chennai, India

More information

Modular Rotor Single Phase Field Excited Flux Switching Machine With Non-Overlapped Windings

Modular Rotor Single Phase Field Excited Flux Switching Machine With Non-Overlapped Windings 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 16 17 18 19 2 21 22 23 24 25 26 27 28 29 3 31 32 33 34 35 36 37 38 39 4 41 42 43 44 45 Article Modular Rotor Single Phase Field Excited Flux Switching Machine With Non-Overlapped

More information

Design of Outer Rotor Permanent Magnet Flux Switching Machine for Downhole Application

Design of Outer Rotor Permanent Magnet Flux Switching Machine for Downhole Application Design of Outer Rotor Permanent Magnet Flux Switching Machine for Downhole Application Rajesh Kumar 1*, Erwan Sulaiman 1, Laili Iwani Jusoh 1 and Fatihah Shafiqah Bahrim 1 1 Department of Electrical Power

More information

The Effects of Magnetic Circuit Geometry on Torque Generation of 8/14 Switched Reluctance Machine

The Effects of Magnetic Circuit Geometry on Torque Generation of 8/14 Switched Reluctance Machine 213 XXIV International Conference on Information, Communication and Automation Technologies (ICAT) October 3 November 1, 213, Sarajevo, Bosnia and Herzegovina The Effects of Magnetic Circuit Geometry on

More information

INFLUENCE OF MAGNET POLE ARC VARIATION ON THE COGGING TORQUE OF RADIAL FLUX PERMANENT MAGNET BRUSHLESS DC (PMBLDC) MOTOR

INFLUENCE OF MAGNET POLE ARC VARIATION ON THE COGGING TORQUE OF RADIAL FLUX PERMANENT MAGNET BRUSHLESS DC (PMBLDC) MOTOR INFLUENCE OF MAGNET POLE ARC VARIATION ON THE COGGING TORQUE OF RADIAL FLUX PERMANENT MAGNET BRUSHLESS DC (PMBLDC) MOTOR Amit N.Patel 1, Aksh P. Naik 2 1,2 Department of Electrical Engineering, Institute

More information

Cogging Torque Reduction of IPM Motor using Skewing, Notching, Pole Pairing and Rotor Pole Axial Pairing.

Cogging Torque Reduction of IPM Motor using Skewing, Notching, Pole Pairing and Rotor Pole Axial Pairing. Cogging Torque Reduction of IPM Motor using Skewing, Notching, Pole Pairing and Rotor Pole Axial Pairing. Fatihah Shafiqah Bahrim 1,*, E. Sulaiman 1, Laili Iwani Jusoh 1, M. Fairoz Omar 1 and Rajesh Kumar

More information

New Self-Excited Synchronous Machine with Tooth Concentrated Winding

New Self-Excited Synchronous Machine with Tooth Concentrated Winding New Self-Excited Synchronous Machine with Tooth Concentrated Winding Gurakuq Dajaku 1) and Dieter Gerling 2), IEEE 1 FEAAM GmbH, D-85577 Neubiberg, Germany 2 Universitaet der Bundeswehr Muenchen, D-85577

More information

COMPARATIVE STUDY ON MAGNETIC CIRCUIT ANALYSIS BETWEEN INDEPENDENT COIL EXCITATION AND CONVENTIONAL THREE PHASE PERMANENT MAGNET MOTOR

COMPARATIVE STUDY ON MAGNETIC CIRCUIT ANALYSIS BETWEEN INDEPENDENT COIL EXCITATION AND CONVENTIONAL THREE PHASE PERMANENT MAGNET MOTOR COMPARATIVE STUDY ON MAGNETIC CIRCUIT ANALYSIS BETWEEN INDEPENDENT COIL EXCITATION AND CONVENTIONAL THREE PHASE PERMANENT MAGNET MOTOR A. Nazifah Abdullah 1, M. Norhisam 2, S. Khodijah 1, N. Amaniza 1,

More information

Conference on, Article number 64020

Conference on, Article number 64020 NAOSITE: Nagasaki University's Ac Title Author(s) Citation Performance of segment type switche oriented Kaneki, Osamu; Higuchi, Tsuyoshi; Y Electrical Machines and Systems (IC Conference on, Article number

More information

Parametric Optimization and Performance Analysis of Outer Rotor Permanent Magnet Flux Switching Machine for Downhole Application

Parametric Optimization and Performance Analysis of Outer Rotor Permanent Magnet Flux Switching Machine for Downhole Application Journal of Magnetics 22(1), 69-77 (2017) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 https://doi.org/10.4283/jmag.2017.22.1.069 Parametric Optimization and Performance Analysis of Outer Rotor Permanent

More information

European Conference on Nanoelectronics and Embedded Systems for Electric Mobility

European Conference on Nanoelectronics and Embedded Systems for Electric Mobility European Conference on Nanoelectronics and Embedded Systems for Electric Mobility emobility emotion 25-26 th September 2013, Toulouse, France 6-phase Fault-Tolerant Permanent Magnet Traction Drive for

More information

MODULAR ELECTRICAL MACHINES A SURVEY

MODULAR ELECTRICAL MACHINES A SURVEY MODULAR ELECTRICAL MACHINES A SURVEY BENŢIA Ioana, RUBA Mircea, SZABÓ Loránd Department of Electrical Machines, Technical University of Cluj-Napoca 400020 Cluj, Daicoviciu nr. 15, Romania; e-mail: ioana.bentia@yahoo.com

More information

A New Low-Cost Hybrid Switched Reluctance Motor for Adjustable-Speed Pump Applications

A New Low-Cost Hybrid Switched Reluctance Motor for Adjustable-Speed Pump Applications A New Low-Cost Hybrid Switched Reluctance Motor for Adjustable-Speed Pump Applications K. Y. Lu, P. O. Rasmussen, S. J. Watkins, F. Blaabjerg Institute of Energy Technology Aalborg University DK-922 Aalborg

More information

Experimental Evaluations of the Dual-Excitation Permanent Magnet Vernier Machine

Experimental Evaluations of the Dual-Excitation Permanent Magnet Vernier Machine Experimental Evaluations of the Dual-Excitation Permanent Magnet Vernier Machine Akio Toba*, Hiroshi Ohsawa*, Yoshihiro Suzuki**, Tukasa Miura**, and Thomas A. Lipo*** Fuji Electric Co. R&D, Ltd. * 1 Fuji-machi,

More information

A High Torque Segmented Outer Rotor Permanent Magnet Flux Switching Motor for Motorcycle Propulsion

A High Torque Segmented Outer Rotor Permanent Magnet Flux Switching Motor for Motorcycle Propulsion A High Torque Segmented Outer Rotor Permanent Magnet Flux Switching Motor for Motorcycle Propulsion Enwelum Mbadiwe I *, Erwan Sulaiman, and Ahmad Md Zarafi Research Centre for Applied Electromagnetics,

More information

Effect of Permanent Magnet Rotor Design on PMSM Properties

Effect of Permanent Magnet Rotor Design on PMSM Properties Transactions on Electrical Engineering, Vol. 1 (2012), No. 3 98 Effect of Permanent Magnet Rotor Design on PMSM Properties SEKERÁK Peter, HRABOVCOVÁ Valéria, RAFAJDUS Pavol, KALAMEN Lukáš, ONUFER Matúš

More information

WITH the requirements of reducing emissions and

WITH the requirements of reducing emissions and IEEE TRANSACTIONS ON MAGNETICS, VOL. 51, NO. 3, MARCH 2015 8201805 Investigation and Design of a High-Power Flux-Switching Permanent Magnet Machine for Hybrid Electric Vehicles Wei Hua, Gan Zhang, and

More information

Joule losses of magnets in permanent magnet synchronous machines - case concentrated winding machine

Joule losses of magnets in permanent magnet synchronous machines - case concentrated winding machine Joule losses of magnets in permanent magnet synchronous machines - case concentrated winding machine Hanne Jussila Lappeenranta University of Technology 1 Joule losses of permanent magnets Eddy current

More information

A novel flux-controllable vernier permanent-magnet machine

A novel flux-controllable vernier permanent-magnet machine Title A novel flux-controllable vernier permanent-magnet machine Author(s) Liu, C; Zhong, J; Chau, KT Citation The IEEE International Magnetic Conference (INTERMAG2011), Teipei, Taiwan, 25-29 April 2011.

More information

THE advancement in the manufacturing of permanent magnets

THE advancement in the manufacturing of permanent magnets IEEE TRANSACTIONS ON MAGNETICS, VOL. 43, NO. 8, AUGUST 2007 3435 Design Consideration to Reduce Cogging Torque in Axial Flux Permanent-Magnet Machines Delvis Anibal González, Juan Antonio Tapia, and Alvaro

More information

Cyclic Parameter Refinement of 4S-10 Hybrid Flux-Switching Motor for Lightweight Electric Vehicle

Cyclic Parameter Refinement of 4S-10 Hybrid Flux-Switching Motor for Lightweight Electric Vehicle IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Cyclic Parameter Refinement of 4S-10 Hybrid Flux-Switching Motor for Lightweight Electric Vehicle To cite this article: J Abd

More information

CHAPTER 3 DESIGN OF THE LIMITED ANGLE BRUSHLESS TORQUE MOTOR

CHAPTER 3 DESIGN OF THE LIMITED ANGLE BRUSHLESS TORQUE MOTOR 33 CHAPTER 3 DESIGN OF THE LIMITED ANGLE BRUSHLESS TORQUE MOTOR 3.1 INTRODUCTION This chapter presents the design of frameless Limited Angle Brushless Torque motor. The armature is wound with toroidal

More information

Comparison of IPM and SPM motors using ferrite magnets for low-voltage traction systems

Comparison of IPM and SPM motors using ferrite magnets for low-voltage traction systems EVS28 KINTEX, Korea, May 3-6, 215 Comparison of IPM and SPM motors using ferrite magnets for low-voltage traction systems Yong-Hoon Kim 1, Suwoong Lee 1, Eui-Chun Lee 1, Bo Ram Cho 1 and Soon-O Kwon 1

More information

CHAPTER 4 HARDWARE DEVELOPMENT OF DUAL ROTOR RADIAL FLUX PERMANENT MAGNET GENERATOR FOR STAND-ALONE WIND ENERGY SYSTEMS

CHAPTER 4 HARDWARE DEVELOPMENT OF DUAL ROTOR RADIAL FLUX PERMANENT MAGNET GENERATOR FOR STAND-ALONE WIND ENERGY SYSTEMS 66 CHAPTER 4 HARDWARE DEVELOPMENT OF DUAL ROTOR RADIAL FLUX PERMANENT MAGNET GENERATOR FOR STAND-ALONE WIND ENERGY SYSTEMS 4.1 INTRODUCTION In this chapter, the prototype hardware development of proposed

More information

Comparison of different 600 kw designs of a new permanent magnet generator for wind power applications

Comparison of different 600 kw designs of a new permanent magnet generator for wind power applications Comparison of different 600 kw designs of a new permanent magnet generator for wind power applications E. Peeters, Vito, Boeretang 200, 2400 Mol, Belgium, eefje.peeters@vito.be, tel +32 14 33 59 23, fax

More information

PM Assisted, Brushless Wound Rotor Synchronous Machine

PM Assisted, Brushless Wound Rotor Synchronous Machine Journal of Magnetics 21(3), 399-404 (2016) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2016.21.3.399 PM Assisted, Brushless Wound Rotor Synchronous Machine Qasim Ali 1,

More information

DESIGN EVALUATIONS OF THE NEW DOUBLE ROTOR INTERIOR PERMANENT MAGNET MACHINE

DESIGN EVALUATIONS OF THE NEW DOUBLE ROTOR INTERIOR PERMANENT MAGNET MACHINE Journal of Engineering Science and Technology EURECA 2014 Special Issue April (2015) 73-84 School of Engineering, Taylor s University DESIGN EVALUATIONS OF THE NEW DOUBLE ROTOR INTERIOR PERMANENT MAGNET

More information

A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling)

A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling) A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling) M EL_SHANAWANY, SMR TAHOUN& M EZZAT Department (Electrical Engineering Department) University

More information

A Novel Axial-flux Electric Machine for In-wheel Gearless Drive in Plug-in Hybrid Electric Vehicles

A Novel Axial-flux Electric Machine for In-wheel Gearless Drive in Plug-in Hybrid Electric Vehicles A Novel Axial-flux Electric Machine for In-wheel Gearless Drive in Plug-in Hybrid Electric Vehicles W. N. Fu, and S. L. Ho The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong A novel low-speed

More information

Design and Analysis of Radial Flux Permanent Magnet Brushless DC Motor for Gearless Elevators

Design and Analysis of Radial Flux Permanent Magnet Brushless DC Motor for Gearless Elevators International Journal of Control Theory and Applications ISSN : 0974-5572 International Science Press Volume 9 Number 43 2016 Design and Analysis of Radial Flux Permanent Magnet Brushless DC Motor for

More information

This is a repository copy of Torque performance of axial flux permanent magnet fractional open slot machine with unequal teeth

This is a repository copy of Torque performance of axial flux permanent magnet fractional open slot machine with unequal teeth This is a repository copy of Torque performance of axial flux permanent magnet fractional open slot machine with unequal teeth Article: Kierstead, H.J., Wang, R-J., Kamper, M.J., (20) Torque performance

More information

PERFORMANCE STUDIES OF HEFSM WITH 6 SLOT- 7 POLE FOR HEV APPLICATION ISMAIL ISHAQ BIN IBRAHIM

PERFORMANCE STUDIES OF HEFSM WITH 6 SLOT- 7 POLE FOR HEV APPLICATION ISMAIL ISHAQ BIN IBRAHIM PERFORMANCE STUDIES OF HEFSM WITH 6 SLOT- 7 POLE FOR HEV APPLICATION ISMAIL ISHAQ BIN IBRAHIM A thesis submitted in fulfillment of the requirement for the award of the Degree of Master of Electrical Engineering

More information

Optimization Design of an Interior Permanent Magnet Motor for Electro Hydraulic Power Steering

Optimization Design of an Interior Permanent Magnet Motor for Electro Hydraulic Power Steering Indian Journal of Science and Technology, Vol 9(14), DOI: 10.17485/ijst/2016/v9i14/91100, April 2016 ISSN (Print) : 0974-6846 ISSN (Online) : 0974-5645 Optimization Design of an Interior Permanent Magnet

More information

COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK SUBJECT CODE & NAME : EE 1001 SPECIAL ELECTRICAL MACHINES

COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK SUBJECT CODE & NAME : EE 1001 SPECIAL ELECTRICAL MACHINES KINGS COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK SUBJECT CODE & NAME : EE 1001 SPECIAL ELECTRICAL MACHINES YEAR / SEM : IV / VII UNIT I SYNCHRONOUS RELUCTANCE

More information

Cogging Reduction of a Low-speed Direct-drive Axial-gap Generator

Cogging Reduction of a Low-speed Direct-drive Axial-gap Generator APSAEM14 Jorunal of the Japan Society of Applied Electromagnetics and Mechanics Vol.23, No.3 (2015) Regular Paper Cogging Reduction of a Low-speed Direct-drive Axial-gap Generator Tomoki HASHIMOTO *1,

More information

G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4

G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4 Speed control of Brushless DC motor with DSP controller using Matlab G Prasad 1, Venkateswara Reddy M 2, Dr. P V N Prasad 3, Dr. G Tulasi Ram Das 4 1 Department of Electrical and Electronics Engineering,

More information

Design Analysis of a Dual Rotor Permanent Magnet Machine driven Electric Vehicle

Design Analysis of a Dual Rotor Permanent Magnet Machine driven Electric Vehicle Design Analysis of a Dual Rotor Permanent Magnet Machine driven Electric Vehicle Mohd Izzat Bin Zainuddin 1, Aravind CV 1,* 1 School of Engineering, Taylor s University, Malaysia Abstract. Electric bike

More information

Development of High-Efficiency Permanent Magnet Synchronous Generator for Motorcycle Application

Development of High-Efficiency Permanent Magnet Synchronous Generator for Motorcycle Application Development of High-Efficiency Permanent Magnet Synchronous Generator for Motorcycle Application Toshihiko Noguchi, Yuki Kurebayashi, Tetsuya Osakabe, and Toshihisa Takagi Shizuoka University and Suzuki

More information

CHAPTER 5 ANALYSIS OF COGGING TORQUE

CHAPTER 5 ANALYSIS OF COGGING TORQUE 95 CHAPTER 5 ANALYSIS OF COGGING TORQUE 5.1 INTRODUCTION In modern era of technology, permanent magnet AC and DC motors are widely used in many industrial applications. For such motors, it has been a challenge

More information

QUESTION BANK SPECIAL ELECTRICAL MACHINES

QUESTION BANK SPECIAL ELECTRICAL MACHINES SEVENTH SEMESTER EEE QUESTION BANK SPECIAL ELECTRICAL MACHINES TWO MARK QUESTIONS 1. What is a synchronous reluctance 2. What are the types of rotor in synchronous reluctance 3. Mention some applications

More information

Core Loss Effects on Electrical Steel Sheet of Wound Rotor Synchronous Motor for Integrated Starter Generator

Core Loss Effects on Electrical Steel Sheet of Wound Rotor Synchronous Motor for Integrated Starter Generator Journal of Magnetics 20(2), 148-154 (2015) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2015.20.2.148 Core Loss Effects on Electrical Steel Sheet of Wound Rotor Synchronous

More information

A permanent magnet assist, segmented rotor, switched reluctance drive for fault tolerant aerospace applications

A permanent magnet assist, segmented rotor, switched reluctance drive for fault tolerant aerospace applications A permanent magnet assist, segmented rotor, switched reluctance drive for fault tolerant aerospace applications S. Ullah 1, S.P. McDonald 1,R. Martin 1, M.Benarous and G.J. Atkinson 1 1. School of Electrical

More information

Journal of Asian Scientific Research. DESIGN OF SWITCHED RELUCTANCE MOTOR FOR ELEVATOR APPLICATION T. Dinesh Kumar. A. Nagarajan

Journal of Asian Scientific Research. DESIGN OF SWITCHED RELUCTANCE MOTOR FOR ELEVATOR APPLICATION T. Dinesh Kumar. A. Nagarajan Journal of Asian Scientific Research journal homepage: http://aessweb.com/journal-detail.php?id=5003 DESIGN OF SWITCHED RELUCTANCE MOTOR FOR ELEVATOR APPLICATION T. Dinesh Kumar PG scholar, Department

More information

Study of Motoring Operation of In-wheel Switched Reluctance Motor Drives for Electric Vehicles

Study of Motoring Operation of In-wheel Switched Reluctance Motor Drives for Electric Vehicles Study of Motoring Operation of In-wheel Switched Reluctance Motor Drives for Electric Vehicles X. D. XUE 1, J. K. LIN 2, Z. ZHANG 3, T. W. NG 4, K. F. LUK 5, K. W. E. CHENG 6, and N. C. CHEUNG 7 Department

More information

Axial-flux PM Synchronous Machines with Air-gap Profiling and Very High Ratio of Spoke Rotor Poles to Stator Concentrated Coils

Axial-flux PM Synchronous Machines with Air-gap Profiling and Very High Ratio of Spoke Rotor Poles to Stator Concentrated Coils Axial-flux PM Synchronous Machines with Air-gap Profiling and Very High Ratio of Spoke Rotor Poles to Stator Concentrated Coils Vandana Rallabandi, Narges Taran and Dan M. Ionel, Fellow, IEEE Department

More information

This is a repository copy of Investigation on synchronous reluctance machines with different rotor topologies and winding configurations.

This is a repository copy of Investigation on synchronous reluctance machines with different rotor topologies and winding configurations. This is a repository copy of Investigation on synchronous reluctance machines with different rotor topologies and winding configurations. White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/119473/

More information

DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY MAMALLAPURAM, CHENNAI

DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY MAMALLAPURAM, CHENNAI DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY MAMALLAPURAM, CHENNAI -603104 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK VII SEMESTER EE6501-Power system Analysis

More information

DESIGN OF COMPACT PERMANENT-MAGNET SYNCHRONOUS MOTORS WITH CONCENTRATED WINDINGS

DESIGN OF COMPACT PERMANENT-MAGNET SYNCHRONOUS MOTORS WITH CONCENTRATED WINDINGS DESIGN OF COMPACT PERMANENT-MAGNET SYNCHRONOUS MOTORS WITH CONCENTRATED WINDINGS CSABA DEAK, ANDREAS BINDER Key words: Synchronous motor, Permanent magnet, Concentrated winding. The design and comparison

More information

DESIGN AND ANALYSIS OF NEW CLASS BRUSHLESS D.C MOTOR (FSM)

DESIGN AND ANALYSIS OF NEW CLASS BRUSHLESS D.C MOTOR (FSM) DESIGN AND ANALYSIS OF NEW CLASS BRUSHLESS D.C MOTOR (FSM) Tefera Kitaba 1, Dr.A.Kavitha 2, DEEE, Anna University CEG Campus Chennai, India. teferakitaba@ymail.com, Department of Electrical and Electronics

More information

Design of Sensorless Controlled IPMSM with Concentrated Winding for EV Drive at Low speed

Design of Sensorless Controlled IPMSM with Concentrated Winding for EV Drive at Low speed EVS27 Barcelona, Spain, November 17-20, 2013 Design of Sensorless Controlled IPMSM with Concentrated Winding for EV Drive at Low speed Myung-Seop Lim 1, Seung-Hee Chai 1 and Jung-Pyo Hong 1, Senior Member,

More information

A New Design Approach for Torque Improvement and Torque Ripple Reduction in a Switched Reluctance Motor

A New Design Approach for Torque Improvement and Torque Ripple Reduction in a Switched Reluctance Motor IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 12, Issue 5 Ver. II (Sep. Oct. 2017), PP 51-58 www.iosrjournals.org A New Design Approach

More information

A Linear Magnetic-geared Free-piston Generator for Range-extended Electric Vehicles

A Linear Magnetic-geared Free-piston Generator for Range-extended Electric Vehicles A Linear Magnetic-geared Free-piston Generator for Range-extended Electric Vehicles Wenlong Li 1 and K. T. Chau 2 1 Department of Electrical and Electronic Engineering, The University of Hong Kong, wlli@eee.hku.hk

More information

CHAPTER 1 INTRODUCTION

CHAPTER 1 INTRODUCTION 1 CHAPTER 1 INTRODUCTION 1.1 ELECTRICAL MOTOR This thesis address the performance analysis of brushless dc (BLDC) motor having new winding method in the stator for reliability requirement of electromechanical

More information

Comparison and analysis of flux-switching permanent-magnet double-rotor machine with 4QT used for HEV

Comparison and analysis of flux-switching permanent-magnet double-rotor machine with 4QT used for HEV Title Comparison and analysis of flux-switching permanent-magnet double-rotor machine with 4QT used for HEV Author(s) Mo, L; Quan, L; Zhu, X; Chen, Y; Qiu, H; Chau, KT Citation The 2014 IEEE International

More information

Research on Torque Ripple Optimization of Switched Reluctance Motor Based on Finite Element Method

Research on Torque Ripple Optimization of Switched Reluctance Motor Based on Finite Element Method Progress In Electromagnetics Research M, Vol. 74, 115 123, 18 Research on Torque Ripple Optimization of Switched Reluctance Motor Based on Finite Element Method Libing Jing * and Jia Cheng Abstract Torque

More information

Aspects of Permanent Magnet Machine Design

Aspects of Permanent Magnet Machine Design Aspects of Permanent Magnet Machine Design Christine Ross February 7, 2011 Grainger Center for Electric Machinery and Electromechanics Outline Permanent Magnet (PM) Machine Fundamentals Motivation and

More information

Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method

Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method Title Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method Author(s) Wang, Y; Chau, KT; Chan, CC; Jiang, JZ

More information

Comparative Study of Maximum Torque Control by PI ANN of Induction Motor

Comparative Study of Maximum Torque Control by PI ANN of Induction Motor Comparative Study of Maximum Torque Control by PI ANN of Induction Motor Dr. G.Madhusudhana Rao 1 and G.Srikanth 2 1 Professor of Electrical and Electronics Engineering, TKR College of Engineering and

More information

A High Torque Density Axial Flux SRM with Modular Stator

A High Torque Density Axial Flux SRM with Modular Stator A High Torque Density Axial Flux SRM with Modular Stator Y. Ebrahimi* and M. R. Feyzi* (C.A.) Abstract: A novel structure of Switched Reluctance Motors (SRMs) is proposed. The proposed structure uses the

More information

An Investigation of Advanced Magnetic Materials for Axial Field Brushless Permanent Magnet Motor Drives for Automotive Applications

An Investigation of Advanced Magnetic Materials for Axial Field Brushless Permanent Magnet Motor Drives for Automotive Applications The following paper posted here is not the official IEEE published version. The final published version of this paper can be found in the Proceedings of the IEEE Power Electronics Specialist Conference

More information

Preliminary Study of a New Topology Permanent Magnet Flux Switching Motor for Electric Buses

Preliminary Study of a New Topology Permanent Magnet Flux Switching Motor for Electric Buses Indonesian Journal of Electrical Engineering and Computer Science Vol. 10, No. 2, May 2018, pp. 446~455 ISSN: 2502-4752, DOI: 10.11591/ijeecs.v10.i2.pp446-455 446 Preliminary Study of a New Topology Permanent

More information

Rotor Design & Performance for a BDFM

Rotor Design & Performance for a BDFM 439 1 Rotor Design & Performance for a BDFM P J Tavner +, R A McMahon *, P Roberts *, E Abdi-Jalebi *, X Wang *, M Jagieła #, T Chick* Abstract Analysis of the behaviour of the Brushless Doubly Fed Machine

More information

Development of Hybrid Electric Compressor Motor Drive System for Hybrid Electrical Vehicles

Development of Hybrid Electric Compressor Motor Drive System for Hybrid Electrical Vehicles 960 Journal of Power Electronics, Vol. 9, No. 6, November 2009 JPE 9-6-15 Development of Hybrid Electric Compressor Motor Drive System for Hybrid Electrical Vehicles Tae-Uk Jung Department of Electrical

More information

Cooling Enhancement of Electric Motors

Cooling Enhancement of Electric Motors Cooling Enhancement of Electric Motors Authors : Yasser G. Dessouky* and Barry W. Williams** Dept. of Computing & Electrical Engineering Heriot-Watt University Riccarton, Edinburgh EH14 4AS, U.K. Fax :

More information

Keywords: Hybrid electric vehicle, free-piston generator, linear magnetic-geared machine, finite element analysis

Keywords: Hybrid electric vehicle, free-piston generator, linear magnetic-geared machine, finite element analysis An Integrated PM Magnetic-geared Machine for Hybrid Electric Vehicles Hua Fan, K. T. Chau 1, Chunhua Liu, C. C. Chan, and T.W. Ching 1 K. T. Chau (corresponding author) The University of Hong Kong, Pokfulam

More information

DESIGN OF A NEW ELECTROMAGNETIC VALVE WITH A HYBRID PM/EM ACTUATOR IN SI ENGINES

DESIGN OF A NEW ELECTROMAGNETIC VALVE WITH A HYBRID PM/EM ACTUATOR IN SI ENGINES Journal of Marine cience and Technology, Vol. 22, o. 6, pp. 687-693 (214) 687 DOI: 1.6119/JMT-14-321-4 DEIG OF A EW ELECTROMAGETIC VALVE WITH A HYBRID PM/EM ACTUATOR I I EGIE Ly Vinh Dat 1 and Yaojung

More information

2014 ELECTRICAL TECHNOLOGY

2014 ELECTRICAL TECHNOLOGY SET - 1 II B. Tech I Semester Regular Examinations, March 2014 ELECTRICAL TECHNOLOGY (Com. to ECE, EIE, BME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~~~

More information

International Journal of Advance Research in Engineering, Science & Technology

International Journal of Advance Research in Engineering, Science & Technology Impact Factor (SJIF): 4.542 International Journal of Advance Research in Engineering, Science & Technology e-issn: 2393-9877, p-issn: 2394-2444 Volume 4, Issue 4, April-2017 Simulation and Analysis for

More information

Note 8. Electric Actuators

Note 8. Electric Actuators Note 8 Electric Actuators Department of Mechanical Engineering, University Of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada 1 1. Introduction In a typical closed-loop, or feedback, control

More information

Design and Finite Element Analysis of Hybrid Stepper Motor for Spacecraft Applications

Design and Finite Element Analysis of Hybrid Stepper Motor for Spacecraft Applications Design and Finite Element Analysis of Hybrid Stepper Motor for Spacecraft Applications Praveen R.P., Ravichandran M.H., V. T. Sadasivan Achari, Dr.Jagathy Raj V. P., Dr.G.Madhu and Dr.G.R. Bindu 6 Abstract

More information

A Quantitative Comparative Analysis of a Novel Flux-Modulated Permanent Magnet Motor for Low-Speed Drive

A Quantitative Comparative Analysis of a Novel Flux-Modulated Permanent Magnet Motor for Low-Speed Drive ANSYS 11 中国用户大会优秀论文 A Quantitative Comparative Analysis of a Novel Flux-Modulated Permanent Magnet Motor for Low-Speed Drive W. N. Fu, and S. L. Ho The Hong Kong Polytechnic University, Hung Hom, Kowloon,

More information

University of L Aquila. Permanent Magnet-assisted Synchronous Reluctance Motors for Electric Vehicle applications

University of L Aquila. Permanent Magnet-assisted Synchronous Reluctance Motors for Electric Vehicle applications University of L Aquila Department of Industrial and Information Engineering and Economics Permanent Magnet-assisted Synchronous Reluctance Motors for Electric Vehicle applications A. Ometto, F. Parasiliti,

More information

STEADY STATE PERFORMANCE OF THE WOUND-ROTOR HYBRID STEPPING MOTOR

STEADY STATE PERFORMANCE OF THE WOUND-ROTOR HYBRID STEPPING MOTOR ISSN (Print) : 232 3765 STEADY STATE PERFORMANCE OF THE WOUND-ROTOR HYBRID STEPPING MOTOR Jonathan U. Agber Senior Lecturer, Department of Electrical and Electronics Engineering,Federal University of Agriculture,

More information

A STUDY OF A MULTI-STEP POLE TYPE ELECTRO-MAGNETIC ACTUATOR FOR CONTROLLING PROPORTIONAL HYDRAULIC VALVE

A STUDY OF A MULTI-STEP POLE TYPE ELECTRO-MAGNETIC ACTUATOR FOR CONTROLLING PROPORTIONAL HYDRAULIC VALVE P1-6 Proceedings of the 7th JFPS International Symposium on Fluid Power, TOYAMA 28 September 15-18, 28 A STUDY OF A MULTI-STEP POLE TYPE ELECTRO-MAGNETIC ACTUATOR FOR CONTROLLING PROPORTIONAL HYDRAULIC

More information

2018 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM POWER & MOBILITY (P&M) TECHNICAL SESSION AUGUST 7-9, NOVI, MICHIGAN

2018 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM POWER & MOBILITY (P&M) TECHNICAL SESSION AUGUST 7-9, NOVI, MICHIGAN 2018 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM POWER & MOBILITY (P&M) TECHNICAL SESSION AUGUST 7-9, 2018 - NOVI, MICHIGAN A Demonstration of Noise and Vibration Reduction Techniques

More information

Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator

Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator Transient Analysis of Offset Stator Double Sided Short Rotor Linear Induction Motor Accelerator No. Fred Eastham Department of Electronic and Electrical Engineering, the University of Bath, Bath, BA2 7AY,

More information

Characteristics Analysis of Novel Outer Rotor Fan-type PMSM for Increasing Power Density

Characteristics Analysis of Novel Outer Rotor Fan-type PMSM for Increasing Power Density Journal of Magnetics 23(2), 247-252 (2018) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 https://doi.org/10.4283/jmag.2018.23.2.247 Characteristics Analysis of Novel Outer Rotor Fan-type PMSM for Increasing

More information

Royal Institute of Technology (KTH) S Stockholm Sweden

Royal Institute of Technology (KTH) S Stockholm Sweden Oskar Wallmark oskar.wallmark@ee.kth.se School of Electrical Engineering Phone: +46 8 790 7831 (work) Electrical Energy Conversion (E2C) Fax: +46 8 205 268 Royal Institute of Technology (KTH) S-100 44

More information

A ROTOR CONSISTING OF TWO IRON CYLINDERS FOR SWITCHED RELUCTANCE MOTORS

A ROTOR CONSISTING OF TWO IRON CYLINDERS FOR SWITCHED RELUCTANCE MOTORS Journal of ELECTRICAL ENGINEERING, VOL. 58, NO. 2, 2007, 85 90 A ROTOR CONSISTING OF TWO IRON CYLINDERS FOR SWITCHED RELUCTANCE MOTORS Eyhab El-kharashi The shaft in a conventional switched reluctance

More information

Permanent magnet machines and actuators

Permanent magnet machines and actuators Permanent magnet machines and actuators Geraint Jewell The University of Sheffield Symposium on Materials for a Sustainable Future 11/09/09 1 Key PM Properties for Electro-Mechanical Devices High remanence

More information

An investigation on development of Precision actuator for small robot

An investigation on development of Precision actuator for small robot An investigation on development of Precision actuator for small robot Joo Han Kim*, Se Hyun Rhyu, In Soung Jung, Jung Moo Seo Korea Electronics Technology Institute (KETI) * 203-103 B/D 192 Yakdae-Dong,

More information

Procedia - Social and Behavioral Sciences 195 ( 2015 ) World Conference on Technology, Innovation and Entrepreneurship

Procedia - Social and Behavioral Sciences 195 ( 2015 ) World Conference on Technology, Innovation and Entrepreneurship Available online at www.sciencedirect.com ScienceDirect Procedia - Social and Behavioral Sciences 195 ( 2015 ) 2586 2591 World Conference on Technology, Innovation and Entrepreneurship Application of Finite

More information

Fig. 1 Cross section of 8P18S IPM motor. Fig. 2 FEA model of the IPM motor. 3. Design Optimization Variables Design optimization is carried out using

Fig. 1 Cross section of 8P18S IPM motor. Fig. 2 FEA model of the IPM motor. 3. Design Optimization Variables Design optimization is carried out using 2011 International Conference on Signal, Image Processing and Applications With workshop of ICEEA 2011 IPCSIT vol.21 (2011) (2011) IACSIT Press, Singapore Effect of Skew and Radii Ratio on Motor Performance

More information