Pushbuttons/Selectors/Pilot Lights/Buzzers AH164, AH165 and AH165-2 General information

Transcription

1 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and General information Features Design basis The 16mm dia. series of compact size pushbuttons are 'finger-size', and consequently take up little panel space series operators are about twice as large as the 164 and 165 series operators for easier operation. With many types of operator available, the most suitable switch can be identified by color, shape and legend, and have a smooth, quality "snap-action". In spite of their small size they have a highly reliable mechanism, and are eminently suited for solid state and other electronic circuits. 164, 165 and series contact block holders can easily be removed manually. Moreover, the contact block can be easily attached or detached without using any special tools, thus facilitating addition or replacement of contact. elector switches elector switches can also be supplied in either knob-handle operated or key operated types. trong construction The operator and contact blocks are molded from an excellent thermal resistance resin and can withstand the heat at the time of soldering. ince these pushbuttons are manufactured to industrial standards they can withstand vibration or shock thus eliminating lamp failure due to such causes as loose bases. With regard to the degree of protection, standard types which met the requirements of IP40 of Pub. No. 529, IC tandards, and oil tight types which meet the requirements of IP65 of the said, are available. This permits the application to various fields, from machine tools to O (Office utomation) facilities. Quality feel tough Both the operator and contact block are precisely engineered. There is no fear of the switch malfunction even after long use and it continues to operate smoothly for its service life of about 1,000,000 operations. Pushbuttons Illuminated pushbuttons Pilot lights K T 164-Z mergency stop pushbuttons asy color change Color lenses fit over the inner button. The lens can easily be removed using a small screwdriver Color lens F V6 crew driver Note: The luminous color of Ds and neon illumination types varies with the body color of the product. Visible inscription Button legends are printed on legend sheet, which is stuck to the legend plate on the inner button. The lettering is back lit by the switch lamp and the inscription is highly visible through the color lens. Contact FUJI for your lettering requirements. egend plate egend sheet (film) xcellent switch reliability The switch uses a snap-action mechanism. The pushbuttons are available with either momentary or alternative actions. The snap-action switch has a double break movement which operates independently of the speed of switching. The contacts are made from gold-flashed silver. igh contact reliability of 1m at 5V C/DC is assured. Contact blocks are available in to arrangement. arge terminals older/tab terminal is provided as standard. Wire-wrap terminal is available on reguest. K-1100 F M electors K-1139 F P afety FUJI s original Trigger ction mechanism is used in the emergency stop pushbuttons. They are suitable for emergency stop and safety. This mechanism prevents the contacts from moving until the button is pushed and locked. Provided with a trigger action mechanism conforming to N4. Provided with direct opening action (approved by TÜV) conforming to N and N lternate action In the case of alternate action when the button is depressed the contacts are maintained and remain so even if the finger is removed. The button will not return to its free position. In order to remove the lock, the button must be given a second pressure before the button will return to its free position. This makes it most suitable as the switch for a power source. Maintain Pushbutton with finger guards Finger guards are provided for square or rectangular type pushbuttons (F, TF, and T types) in order to prevent operational error of adjacent buttons. pprovals amp terminal Contact terminal For further information related to approved type, see page /132 to /136. Fuji lectric F Components & ystems Co., td./d & C Catalog /131

2 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Quick reference guide 164 (standard) / 165 (oil-tight) Illuminated pushbutton switches Operator Type Operator Type Operator Type xtended round head 164-, 5 Flush square head 164-, 5 Flush rectangular head 164-T, T5 165-, , T, T5 ee page /142 ee page /142 ee page /142 K-1103 K-1102 K-1100 Flush rectangular head 164-TG, TG5 Flush square head 164-G, G5 with guard 165-TG, TG5 with guard 165-G, G5 ee page /143 ee page /143 K-1101 Note: pot D and red/green D types: Not approved standard Pushbutton switches Operator Type Operator Type Operator Type xtended round head 164-, 5 Mushroom head 164-M, M5 Flush square head 164-F, F5 165-, M, M5 165-F, F5 F ee page /147 ee page /147 ee page /147 K-1103 K-1136 K-1102 Flush rectangular head 164-TF, TF5 Flush rectangular head 164-TGF, TGF5 Flush square head 164-GF, GF5 165-TF, TF5 with guard 165-TGF, TGF5 with guard 165-GF, GF5 ee page /147 ee page /147 ee page /147 K-1100 K-1101 F Convex square head 164-M, M5 Convex rectangular head 164-TM, TM5 Push-lock, turn-reset 165-V 165-M, M5 165-TM, TM5 (32mm dia.) (Direct opening action) ee page /147 ee page /147 ee page /148 Push-lock, turn-reset (40mm dia.) 165-V1 K-1134 K-1135 F (Direct opening action) ee page /148 F mergency stop pushbutton switches (Direct opening action), conform to N4 Operator Type Operator Type Push-lock, turn-reset 165-V5 Push-lock, turn-reset 165-V6 (32mm dia.) (40mm dia.) ee page /148 ee page /148 F F Note: : ee page /5 /132 Fuji lectric F Components & ystems Co., td./d & C Catalog

3 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Quick reference guide elector switches Operator Type Operator Type Operator Type Knob with rectangular 164-P Knob with square bezel 164-P Key with rectangular 164-J bezel 165-P 165-P bezel 165-J ee page /149 ee page /149 ee page /149 K-1099 K-1133 K-1098 Key with square bezel 164-J Key with rectangular 165-JM Key 165-JM 165-J bezel (Direct opening action) (Direct opening action) ee page /149, /2 ee page /0 ee page /0 K-1132 F95-57 F Pilot lights ens Type ens Type ens Type xtended round 164-Z Flush square 164-Z Flush rectangular 164-ZT 165-Z 165-Z 165-ZT ee page /4 ee page /4 ee page /4 Dome 165-ZM K-1139 K-1138 K-1137 ee page /4 F87-45 Buzzers ound Type ound Type ound Type tandard 164-TX oud sound 164-TX1 oud sound with 164-TX2B volume control ee page /6 ee page /6 ee page /6 tandard sound with volume control (IP54) 165-X F F87-44 F ee page /6 F96-3 Note: : ee page /5 Fuji lectric F Components & ystems Co., td./d & C Catalog /133

4 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Quick reference guide Numerical indicators Display Type Display Type Display Type Without decimal decoder 164-T With decimal decoder 164-TC With decimal decoder 164-TC4 165-T (5, 12, V) 165-TC (V) 165-TC4 ee page /7 ee page /7 ee page /7 With sign decorder 164-TC4-1 (±1 display) 165-TC4-1 P-165 F87-3 F ee page /7 F (oil-tight) Illuminated pushbutton switches Operator Type Operator Type Operator Type Flush round head 165-2F, 2F5 xtended round head 165-2, 25 Mushroom head 165-2M ee page /164 ee page /164 ee page /164 F F F Mushroom head with 165-2YM Flush square head 165-2F, 2F5 xtended square head 165-2, 25 square bezel ee page /164 ee page /165 ee page /165 F F F Concave square head 165-2C, 2C5 Push-lock, turn-reset 165-2V Push-lock, turn-reset 165-2YV with square bezel ee page /165 ee page /166 ee page /166 F F F87-2 Note: : ee page /5 /134 Fuji lectric F Components & ystems Co., td./d & C Catalog

5 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Quick reference guide Pushbutton switches Operator Type Operator Type Operator Type Flush round head 165-2F, 2F5 xtended round head 165-2, 25 Mushroom head 165-2M ee page /167 ee page /167 ee page /167 F F F87-2 Mushroom head with 165-2YM Flush square head 165-2F, 2F5 Concave square head 165-2C, 2C5 square bezel ee page /167 ee page /167 ee page /167 F F F xtended square head 165-2, 25 With selector ring With selector ring 165-2Y2 with square bezell ee page /167 ee page /168 ee page /168 F F F Push-lock, turn-reset 165-2V Push-lock, turn-reset 165-2YV with square bezel ee page /168 ee page /168 F F elector switches Operator Type Operator Type Operator Type Knob 165-2P Knob with square bezel 165-2YP Key 165-2J ee page /169 ee page /169 ee page /169 F F F Key with square bezel 165-2YJ ever ever with square bezel ee page /169 ee page /170 ee page /170 F F F Illuminated selector switches Operator Type Knob 165-2P ee page /172 F Note: : ee page /5 Fuji lectric F Components & ystems Co., td./d & C Catalog /135

6 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Quick reference guide Pilot lights ens Type ens Type ens Type Flush round 165-2Z xtended round 165-2Z Flush square 165-2Z ee page /173 ee page /173 ee page /173 F F F xtended square 165-2Z ee page /173 F87-2 Note: : ee page /5 /136 Fuji lectric F Components & ystems Co., td./d & C Catalog

7 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature Pushbuttons, illuminated pushbuttons and pilot lights ➂ Color of button or lens W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 164: tandard (IP40) 165: Oil-tight (IP65) ➁ Operator or lens Operator for illuminated pushbutton : Flush square head 5: Flush square head (lternate) T: Flush rectangular head T5: Flush rectangular head (lternate) : xtended round head 5: xtended round head (lternate) TG: Flush rectangular head with guard TG5: Flush rectangular head with guard (lternate) G: Flush square head with guard G5: Flush square head with guard (lternate) Code G B Y W O G color Green ed Black* Yellow White Blue Orange ed/green Button Notes: ( ): indicates luminous color 165-V, V1, V5, V6: ed only * Not available for illuminated types D Incandescent (Orange) (mber) ➃ Contact arrangement 01: 1NC* 2: 02: 2NC* 1 33: * 2 11: Notes: * 1 vailable for 165-V, V1, V5, V6 * 2 Not available for with transformer types Neon (Orange) (Orange) (Orange) (Green) Operator for pushbuttons F: Flush square head F5: Flush square head (lternate) TF: Flush rectangular head TF5: Flush rectangular head (lternate) : xtended round head 5: xtended round head (lternate) TGF: Flush rectangular head with guard TGF5: Flush rectangular head with guard (lternate) GF: Flush square head with guard GF5: Flush square head with guard (lternate) M: Mushroom head M5: Mushroom head (lternate) M: Convex square head M5: Convex square head (lternate) TM: Convex rectangular head TM5: Convex rectangular head (lternate) V: Push-lock, turn-reset (32mm dia.)* 1 * 2 V1: Push-lock, turn-reset (40mm dia.)* 1 * 2 Operator for emergency stop pushbuttons V5: Push-lock, turn-reset (32mm dia.)* 2 V6: Push-lock, turn-reset (40mm dia.)* 2 ens for pilot lights Z: xtended round Z: Flush square ZT: Flush rectangular ZM: Dome ➄ amp voltage Code B K M P D Incandescent* 2 Neon* 2 5V DC* 2 6V DC* 2 12V DC V DC V C* 1 * V C* 1 * 2 ➅ Type of lamp Blank: Incandescent 1: Neon 2: pot D, D (ZM types) 3: Flat D 5V C/DC 12V C/DC V C/DC V C* V C* 1 Notes: * 1 With transformer (D: V, Incandescent: 28V) * 2 Not available 165-ZM ZM type: D lamp only (12, V DC) ➆ Terminal Blank: older/tab W: Wire-wrap : oder (165-V, V1, V5, V6 types only) Note: ZM types: wire-wrap terminal only (Code is blank) 110V C 120V C 220V C 0V C Note: * 1 Product with no trigger action mechanism * type only, direct opening action Fuji lectric F Components & ystems Co., td./d & C Catalog /137

8 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature elector switches J 2 B 11 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 164: tandard (IP40) 165: Oil-tight (IP65) ➁ Operator 2-position, 3-position (operating angle 90 ) P: Knob with square bezel P: Knob with rectangular bezel J: Key with square bezel J: Key with rectangular bezel JM: Key with rectangular bezel (Direct opening action) * JM: Key (Direct opening action) * Note: * 165 types (2-position) only 3-position (operating angle 45 ) PK: Knob with square bezel PK: Knob with rectangular bezel JK: Key with square bezel JK: Key with rectangular bezel ➂ Operation 2: 2-position, maintained 0: 2-position, spring return* 3: 3-position, maintained 6: 3-position, spring/manual return (eft to center) 7: 3-position, spring/manual return (ight to center) 1: 3-position, spring return Note: * xcept for JM and JM types ➆ Terminal Blank: older/tab W: Wire-warp Note: JM, JM types: older/tab terminal only Buzzers T X B ➀ ➁ ➂ ➃ ➀ Product category 164: tandard (IP00) 165: plash-proof (IP54) ➁ ound TX: tandard (164) TX1: oud sound (164) TX2: oud sound with volume control (164) X: tandard sound with volume control (165) ➂ Color of head B: Black ➃ Operating voltage C: 6V C* 2 DC: 6V DC* 2 : 6V C/DC* 1 : 12 to V C/DC F: 35 to 48V C/DC Notes: * 1 xcept for TX and TX1 types * 2 xcept for TX2 and X types ➃ Color of knob or key removable position Color of knob B: Black Key removable position Code B C D F G 2-position position (operating angle 90 ) 3-position (operating angle 45 ) ➄ Contact arrangement 11: 22: 33: * Note: * xcept for JM and JM types. ➅ Key type No. (standard), B, C, D,, F /138 Fuji lectric F Components & ystems Co., td./d & C Catalog

9 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature Numerical indicators T C4 1 N K ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➇ ➀ Product category 164: tandard (IP40) 165: plash-proof (IP54) ➁ hape of the indicator T: ectangular ➂ Type of decoder : Without decoder C1: With decoder (7447: TT, positive logic) C4: With decoder (4511: C-MO) ➃ uminous color : ed G: Green ➄ Type of common or operating voltage Type of common (without decoder) : node C: Cathode Operating voltage (with decoder) Blank: 5V DC B: 12V DC * C: V DC * : V DC * Note: * TC4 types only ➅ Type of indicator Blank: Decimal* 1 1: ign (±1 display)* 2 Notes: * 1 Input voltage: 5, 12, V DC * 2 Input voltage: V DC ➆ Input logic Blank: Positive logic N: Negative logic * Note: * Input voltage: V DC ➇ Card connector (Input voltage: V DC) K1: Without connector K: With connector Fuji lectric F Components & ystems Co., td./d & C Catalog /139

10 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 atings and specifications tandards approved U508 C C22.2 No.14 TÜV: N TÜV: N N pecifications (Indoor use) Pushbutton switches, illuminated pushbutton switches selector switches, pilot lights Item ated insulation voltage 250V C/DC mbient temperature 20 to +70 C * 1 10 to +70 C * 2 (no condensation or no icing) umidity 45 to 85% (at 5 to +40 C), no condensation or no icing Durability Mechanical Pushbutton switch (operations) Momentary action: 1 million lternate action: 250,000 Push-lock, turn-reset: 100,000 elector switch: 250,000 * 3 lectrical 100,000 (220V C 0.7) Dielectric strength 2000V C, 1 minute (Between lamp and contact terminals: 00V C, 1 minute) Conditional short-circuit current 1000 hort-circuit protective device Fuse 1 * 4 File No File No. 279 (except for 165-ZM) File No (for 165-ZM) Pushbutton (except for 165-V, V1), Illuminated pushbutton: Pushbutton (for 165-V, V1): J elector (except for 165-JM, JM): elector (for 165-JM, JM): J Pilot lights: Buzzer: J (for 164-TX2, 165-X) mergency stop pushbutton: Pollution degree 3 Vibration esonance: 10 to 55z, double amplitude 0.1mm * 5 Constant: 16.7z, double amplitude 3mm hock Malfunction durability: 100m/s 2 * 6 Mechanical durability: 500m/s 2 Operating frequency 1200 operation/hour (on-load factor: 40%) Insulation resistance 100MΩ or more (500V DC megger) Degree of protection IP40 IP65 Notes: * 1 For illuminated pushbutton switch and pilot light: 20 to +55 C * 2 For illuminated pushbutton switch and pilot light: 10 to +55 C * 3 Key insertion/removal durability for selector switch key types: 10,000 * V, V1, JM, JM, V5, V6 types: Fuse 5 * 5 mergency stop type: 10 to 500z, double amplitude 0.7mm (acceleration 50m/s 2 ), according to the test condition of N (1998) * 6 mergency stop type:0m/s 2 Buzzers Item 164-TX 164-TX1 ated insulation voltage Operating voltage 60V C/DC 6V C, 6V DC,12 to V C/DC 35 to 48V C/DC ound level 80dB (0.1m) 90dB (0.1m) 60dB(1m) 70dB(1m) Durability 1000h Frequency 2 ±0.5kz 2.4 to 3.3kz Intermittent cycle pprox. 170 cycle/minute Current consumption 7m(, 48V DC) m (, 48V DC) m(6v DC) 25m (6V DC) Dielectric strength Insulation resistance mbient temperature umidity Operator protection 20m (6, V C) 30m (48V C) 1000V C, 1 minute 30m (V C) 40m (48V C) 50m (6V C) 100MΩ or more (500V DC megger) 20 to +60 C (no condensation or no icing) 45 to 85% (at 5 to +40 C) IP00 Item 164-TX2 165-X ated insulation voltage Operating voltage 60V C/DC 6V C/DC, 12 to V C/DC 35 to 48V C/DC ound level 70dB to 90dB (0.1m) 60dB to 80dB (0.1m) 50dB to 70dB (1m) 40dB to 60dB (1m) Durability 1000h Frequency 2 ±0.5kz 2.4 to 3.3kz Intermittent cycle pprox. 170 cycle/minute Current consumption 30m (6V DC) 20m (, 48V DC) 40m (6,, 48V C) Dielectric strength 1000V C, 1 minute Insulation resistance 100MΩ or more (500V DC megger) mbient temperature umidity 20 to +60 C (no condensation or no icing) 45 to 85% (at 5 to +40 C) Degree of protection IP00 IP54 /140 Fuji lectric F Components & ystems Co., td./d & C Catalog

11 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 atings and specifications Numerical indicators Without decoder Item 164-T (D) 165-T (D) lectrical Forward voltage VF (IF=10m) ed: 2.0V (max. 2.8V), green: 2.1V (max. 2.8V) everse current I (V=3V) 100µ Max. power dissipation pd/eg Max. forward current IF Max. reverse voltage V ed: 40mW, green: 60mW ed: m, green: 20m 3V Opening Topr -20 to +40 C (No condensation or no icing) mbient temperature torage Tstg Degree of protection -30 to +85 C IP40 IP65 With decoder Item 164-TC1, TC4 165-TC1, TC4 164-TC4 165-TC Power supply VCC, VDD (DC) Current consumption mbient Opening Topr temperature torage Tstg Degree of protection 5V±5%, 12V±5%, V±5%, 5V ed: 120m (C1), 100m (C4), green: 170m (C1), 0m (C4) 12V ed: 90m (C4), green: 130m (C4) V±20% Numerical indicator, decimal: 110m Unit indicator: 80m V ed: 90m (C4), green: 130m (C4) -20 to +40 C (No condensation or no icing) -30 to +85 C -20 to +40 C (No condensation or no icing) -30 to +85 C IP40 IP65 IP40 IP65 Contact ratings U/C standards ated thermal current 5 ated operational voltage V 125V 250V Maximum current C (es. load) 5.0 DC (es. load) N standards (TÜV approved) ated thermal current 5 ated operational voltage V 100 to 120V 100 to 125V 200 to 0V ated operational current C (Ind. load) C 13 (Ind. load) C 12 (es. load) DC 13 (Ind. load) DC 12 (es. load) amp ratings ated operational voltage 5V 6V 12V V 110V 120V 220V 0V Consumption D DC 14m (Yellow: 28m) 14m (Yellow: 28m) 14m 14m Incandescent C/DC 0.45W (6V) 0.55W (14V) 0.55W (28V) Neon C 0.19V 0.21V 0.38V 0.42V Notes: With transformer (D): 1.5V/110, 220V With transformer (Incandescent): 2V/110, 220V For the incandescent lamps, the values in parentheses indicate the rated voltage of the lamps. Contact reliability FUJI has confirmed that the unit can be used in 1m circuit conditions at 5V C or DC. The operable range may vary depending on the ambient conditions and type of load. Fuji lectric F Components & ystems Co., td./d & C Catalog /141

12 Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/without transformer Operator amp Voltage Contact Momentary action lternate action 164 type 165 (Oil-tight) type 164 type 165 (Oil-tight) type xtended round head Flat D V DC pot D V DC Incandes- V cent C/DC Neon 110V C V C M M M M1 K M M M M M M M M1 Flush square head Flat D V DC pot D V DC Incandes- V cent C/DC Neon 110V C V C M M M M M M M M1 K M M M M1 Flush rectangular head Flat D V DC 164-T T T T T T T T T T T T5333 pot D V DC 164-T T T T T T T T T T T T5332 Incandes- V 164-T T T T511 cent C/DC 164-T T T T T T T T533 Neon 110V C 164-T T T T T T T T T T T T V C 164-T11M1 165-T11M1 164-T511M1 165-T511M1 164-T22M1 165-T22M1 164-T522M1 165-T522M1 K T33M1 165-T33M1 164-T533M1 165-T533M1 Note: eplace the mark by the button color code, see page /143. /142 Fuji lectric F Components & ystems Co., td./d & C Catalog

13 Illuminated Pushbuttons 164 and 165 Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type Flush rectangular head Flat D V DC 164-TG TG TG TG5113 with guard 164-TG TG TG TG TG TG TG TG5333 Incandes- V 164-TG TG TG TG511 cent C/DC 164-TG TG TG TG TG TG TG TG533 Neon 110V C 164-TG TG TG TG TG TG TG TG TG TG TG TG5331 K V C 164-TG11M1 165-TG11M1 164-TG511M1 165-TG511M1 164-TG22M1 165-TG22M1 164-TG522M1 165-TG522M1 164-TG33M1 165-TG33M1 164-TG533M1 165-TG533M1 Flush square head Flat D V DC 164-G G G G5113 with guard 164-G G G G G G G G5333 Incandes- V 164-G G G G511 cent C/DC 164-G G G G G G G G533 Neon 110V C 164-G G G G G G G G G G G G5331 F V C 164-G11M1 165-G11M1 164-G511M1 165-G511M1 164-G22M1 165-G22M1 164-G522M1 165-G522M1 164-G33M1 165-G33M1 164-G533M1 165-G533M1 Dimensions, mm, 5, 5 ø ø amp terminal 7 10 sq. amp terminal 7 10 sq. sq. T, T5 TG, TG5 G, G5 amp terminal amp terminal sq. sq. Button color Color Green ed White Yellow Blue Orange Code G W Y O amp voltage Voltages other than above are available Code D Incandescent Neon The color lens is made of a tinted transparent material. white illuminated pushbutton is fitted with a transparent color lens.(xcept the neon lamp) With wire-wrap pin terminals have a depth of 47mm. B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC 120V C 0V C Fuji lectric F Components & ystems Co., td./d & C Catalog /143

14 Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/without transformer (ed/green D) Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head ed/green V DC 164-G G G G113 D 164-G G G G223 K G G G G333 Flush square head ed/green V DC 164-G G G G113 D 164-G G G G223 K G G G G333 Flush rectangular head ed/green V DC 164-TG TG T5G T5G113 D 164-TG TG T5G T5G223 K-1100 Discontinued 164-TG TG T5G T5G333 Mar Flush square head with ed/green V DC 164-GG GG G5G G5G113 guard D 164-GG GG G5G G5G223 F GG GG G5G G5G333 Flush rectangular head ed/green V DC 164-TGG TGG TG5G TG5G113 with guard D 164-TGG TGG TG5G TG5G223 K TGG TGG TG5G TG5G333 Note: The only color codes used for red/green Ds are and G. The color lens is transparent. ed/green Ds do not have high-brightness specifications. V DC only elationship between luminous color and terminal + b () ed Green Dimensions, mm ee Page /143 + a (+) imiting resistor /144 Fuji lectric F Components & ystems Co., td./d & C Catalog

15 Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/with transformer Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head Flat D Voltage code F : V C Incandescent M: V C Flush square head Flat D Voltage code F : V Incandes- C cent M: V C Flush rectangular head Flat D Voltage 164-T T T T5113 code F : 164-T T T T V C Incandescent M: 164-T T T T V C 164-T T T T522 Flush rectangular head Flat D Voltage 164-TG TG TG TG5113 with guard code : 164-TG TG TG TG V C Incandes- 164-TG TG TG TG511 cent M: V F C 164-TG TG TG TG522 Flush square head Flat D Voltage 164-G G G G5113 with guard code : 164-G G G G V C Incandes- 164-G G G G511 cent M: V F C 164-G G G G522 Note: eplace the mark by the button color code, see page /146. Fuji lectric F Components & ystems Co., td./d & C Catalog /145

16 Illuminated Pushbuttons 164 and 165 Dimensions, mm 62, 5, 5 62 Insulation cover () b (+) a 7 10 ø ø 32 Insulation cover () b (+) a Transformer primary terminal 48.5 older Transformer unit Transformer primary terminal older 48.5 Transformer unit 62 T, T5 TG, TG5 G, G5 62 () b Insulation cover (+) a Insulation cover (+) a Transformer primary terminal older 48.5 Transformer unit Transformer primary terminal older 48.5 Transformer unit Button color Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. /146 Fuji lectric F Components & ystems Co., td./d & C Catalog

17 Pushbuttons 164 and 165 Pushbutton switches Operator Contact Momentary action lternate action Dimensions, mm 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head φ φ K sq. Flush square head 164-F F F F F F F F522 K F F F F sq. sq. Flush rectangular head 164-TF TF TF TF TF TF TF TF522 K TF TF TF TF Flush rectangular head with guard 164-TGF TGF TGF TGF TGF TGF TGF TGF522 K TGF TGF TGF TGF Flush square head with guard 164-GF GF GF GF GF GF GF GF522 F GF GF GF GF sq. sq. Mushroom head 164-M M M M M M M M522 φ 23.5 K M M M M Convex square head 164-M M M M M M M M sq. K M M M M Convex rectangular head 164-TM TM TM TM TM TM TM TM K TM TM TM TM Button color eplace the mark by the following color code Color Green ed Black White Blue Yellow Orange Code G B W Y O Fuji lectric F Components & ystems Co., td./d & C Catalog The color lens is made of a tinted transparent material. (xcept the M, M, TM types) white pushbutton is fitted with a transparent color lens.(xcept the M, M, TM types) black pushbutton consists of a transparent color lens and an attached black legend plate. (xcept M, M, TM types) With wire-wrap pin terminals have a depth of 47mm. /147

18 Pushbuttons 165 Pushbutton switches (Direct opening action) Operator Button Contact Terminal 165 (oil-tight) type Dimensions, mm color Push-lock, turn-reset ed 1NC older/tab 165-V01 (32mm dia.) older (165-V01-) ø32 F NC 165-V02 (165-V02-).5.5 *(20) Push-lock, turn-reset 1NC 165-V101 (40mm dia.) (165-V101-) ø40 F NC 165-V102 (165-V102-).5.5 *(20) Notes: * ( ) For switch with solder terminal. Contact arrangements indicated in the table can be supplied. Product with no trigger action mechanism. mergency stop pushbutton switches (Direct opening action), conform to N4 Operator Button Contact Terminal 165 (oil-tight) type Dimensions, mm color Push-lock, turn-reset ed 1NC older/tab 165-V501 (32mm dia.) older (165-V501-) 6 (max.) ø32 F NC 165-V502 (165-V502-) * (37.5) Push-lock, turn-reset 1NC 165-V601 (40mm dia.) (165-V601-) 6 (max.) ø40 F NC 165-V602 (165-V602-) * (37.5).5 Notes: * ( ) For switch with solder terminal. Contact arrangements indicated in the table can be supplied. /148 Fuji lectric F Components & ystems Co., td./d & C Catalog

19 elector witches 164 and 165 elector switches/2-position (90-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-P2B P2B11 rectangular bezel 164-P2B P2B P2B P2B33 pring 164-P0B P0B11 return 164-P0B P0B22 F P0B P0B33 Knob with square Maintained 164-P2B P2B11 bezel 164-P2B P2B P2B P2B33 pring 164-P0B P0B11 return 164-P0B P0B22 F P0B P0B33 Key with Maintained 164-J J211 rectangular bezel 164-J J J J J2B J2B11 Fuji lectric F Components & ystems Co., td./d & C Catalog 164-J2B J2B22 B 164-J2B J2B J2D J2D J2D J2D22 D 164-J2D J2D33 pring 164-J J011 return 164-J J022 F J J033 Key with square Maintained 164-J J211 bezel 164-J J J J J2B J2B11 F The operating angle range can be changed as shown below by setting the attached flange shifted by 45 in combination with the contact block. In this case, the minimum mounting pitch is 26mm because the contact block is shifted by 45 from the flange. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. 164-J2B J2B22 B 164-J2B J2B J2D J2D J2D J2D22 D 164-J2D J2D33 pring 164-J J011 return 164-J J J J033 Contact block position Contact arrangement and operator position: 2-position selector switch Contact arrange- ment U Operator eft M U position M ight 3-position selector switch Contact arrange- ment Operator eft U U M position Center ight M φ φ U φ sq. sq. U M /149

20 elector witches 165 elector switches/2-position (90-degree) (Direct opening action) Operator Operation Key Contact 165 (oil-tight) type Dimensions, mm removable position Key with rectangular Maintained 165-JM211 bezel B 165-JM2B11 F95-57 D 165-JM2D JM B 165-JM2B22 F D 165-JM2D22 Key with round bezel Maintained 165-JM211 4(max.) B 165-JM2B11 20 φ sq. D 165-JM2D JM (max.) F B D 165-JM2B JM2D φ sq There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator positions: 2-position selector switch Contact arrangement Operator position eft Terminal number U: Upper contact block ight : ower contact block Contact arrangement Operator position eft U ight /0 Fuji lectric F Components & ystems Co., td./d & C Catalog

21 elector witches 164 and 165 elector switches/3-position (90-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-P3B P3B22 rectangular bezel 164-P3B P3B33 pring/ 164-P6B P6B22 manual return 164-P6B P6B33 pring/ 164-P7B P7B22 manual return 164-P7B P7B33 pring return 164-P1B P1B22 K P1B P1B33 Knob with square Maintained 164-P3B P3B22 bezel 164-P3B P3B33 pring/ 164-P6B P6B22 manual return 164-P6B P6B33 pring/ 164-P7B P7B22 manual return 164-P7B P7B33 pring return 164-P1B P1B22 K P1B P1B33 Key with Maintained* 164-J J322 rectangular bezel 164-J J J J J J J3D J3D22 D 164-J3D J3D J3C J3C22 C 164-J3C J3C33 pring/ 164-J J622 manual return 164-J J633 D 164-J6D J6D J6D J6D33 pring/ 164-J J722 manual return 164-J J J J J J733 pring 164-J J122 K-1098 return 164-J J133 Key with square Maintained* 164-J J322 bezel 164-J J333 D C 164-J J3D J3C J J3D J3C J J3D J3C J J3D J3C33 pring/ 164-J J622 manual return 164-J J633 D 164-J6D J6D J6D J6D33 pring/ 164-J J722 manual return 164-J J J J J J733 pring 164-J J122 K-1132 return 164-J J φ φ sq. sq. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator position: ee page /149. pring return, spring/manual return (spring return): Operation angle 70-degree * vailable key removable position: Code B With wire-wrap pin terminals have a depth of 47mm. Fuji lectric F Components & ystems Co., td./d & C Catalog /1

22 elector witches 164 and 165 elector switches/3-position (45-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-PK3B PK3B22 rectangular bezel 164-PK3B PK3B33 pring/ 164-PK6B PK6B22 manual return 164-PK6B PK6B33 pring/ 164-PK7B PK7B22 manual return 164-PK7B PK7B33 pring return 164-PK1B PK1B22 K PK1B PK1B33 Knob with square Maintained 164-PK3B PK3B22 bezel 164-PK3B PK3B33 pring/ 164-PK6B PK6B22 manual return 164-PK6B PK6B33 pring/ 164-PK7B PK7B22 manual return 164-PK7B PK7B33 pring return 164-PK1B PK1B22 K PK1B PK1B33 Key with Maintained 164-JK JK322 rectangular bezel 164-JK JK JK JK JK JK JK3D JK3D22 D 164-JK3D JK3D JK3C JK3C22 C 164-JK3C JK3C33 pring/ 164-JK JK622 manual return 164-JK JK633 D 164-JK6D JK6D JK6D JK6D33 pring/ 164-JK JK722 manual return 164-JK JK JK JK JK JK733 pring 164-JK JK122 K-1098 return 164-JK JK133 Key with square Maintained 164-JK JK322 bezel 164-JK JK333 D C 164-JK JK JK3D JK3D JK3C JK3C JK JK JK3D JK3D JK3C JK3C33 pring/ 164-JK JK622 manual return 164-JK JK633 D 164-JK6D JK6D JK6D JK6D33 pring/ 164-JK JK722 manual return 164-JK JK JK JK JK JK733 pring 164-JK JK122 K-1132 return 164-JK JK φ φ sq. sq. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator position: ee page /3. /2 Fuji lectric F Components & ystems Co., td./d & C Catalog

23 elector witches 164 and 165 Key removable positions (JK, JK) emvable position Code B C D F G Operation code Key removable position, B, C, D,, F, G D,, F,, G Key code No. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact block position Contact arrangement and operator position: 3-position selector switch Contact arrange- ment Operator eft U U M position Center ight Fuji lectric F Components & ystems Co., td./d & C Catalog /3

24 Pilot ights 164 and 165 Pilot lights/without transformer ens amp Voltage 164 type 165 (oil-tight) type Dimensions, mm xtended round Flat D V DC 164-Z3 165-Z3 pot D V DC 164-Z2 165-Z2 ed/green D V DC 164-ZG3 165-ZG3 Discontinued Mar Incandescent V C/DC 164-Z 165-Z Neon 110V C 164-Z1 165-Z1 220V C 164-ZM1 165-ZM1 Discontinued Mar Discontinued Mar Discontinued Mar Flush square Flat D V DC 164-Z3 165-Z3 Flush rectangular K-1139 K-1138 K-1137 pot D V DC 164-Z2 165-Z2 ed/green D V DC 164-ZG3 165-ZG3 Incandescent V C/DC 164-Z 165-Z Discontinued Mar Neon 110V C 164-Z1 165-Z1 220V C 164-ZM1 165-ZM1 Flat D V DC 164-ZT3 165-ZT3 pot D V DC 164-ZT2 165-ZT2 Discontinued Mar ed/green D V DC 164-ZTG3 165-ZTG3 Incandescent V C/DC 164-ZT 165-ZT Neon 110V C 164-ZT1 165-ZT1 220V C 164-ZTM1 165-ZTM1 Dome D 12V DC 165-ZMB2 F87-45 V DC 165-ZM2 a (+) b () a (+) b () a (+) b () a (+) amp terminal 1sq. b () 1sq ø ø sq. sq. sq. 7 sq. 10 sq (max.) ø ø D sq. Note: The only color codes used for red/green Ds are and G. The color lens is transparent. ed/green Ds do not have high-brightness specifications. elationship between luminous color and terminal + b () + Discontinued a (+) ed Green imiting resistor Mar amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Note: xcept for ZM types and red/green D types Neon 120V C 0V C ens color eplace the mark by the following lens color code Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. white pilot lights is fitted with a transparent color lens. (xcept the neon lamp and dome). With wire-wrap pin terminals have a depth of 29mm. (xcept for ZM type) /4 Fuji lectric F Components & ystems Co., td./d & C Catalog

25 Pilot ights 164 and 165 Pilot lights/with transformer ens amp Voltage 164 type 165 (oil-tight) type Dimensions, mm xtended square F Voltage Flat D : 164-Z3 165-Z V C M: V Incandescent C 164-Z 165-Z Insulation cover Transformer primary terminal 62 () b (+) a Transformer unit ø ø older 32 Flush square F Voltage Flat D : 164-Z3 165-Z V C M: V Incandescent C 164-Z 165-Z Insulation cover Transformer primary terminal 62 () b (+) a 48.5 Transformer unit 7 10 sq. sq. older 32 Flush rectangular F Flat D Voltage : 164-ZT3 165-ZT V C M: V Incandescent C 164-ZT 165-ZT Insulation cover Transformer primary terminal 62 () b (+) a 48.5 Transformer unit 7 10 older ens color eplace the mark by the following lens color code Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. white pilot lights is fitted with a transparent color lens. Fuji lectric F Components & ystems Co., td./d & C Catalog /5

26 Buzzers 164 and 165 Buzzers ound Operating voltage Type Dimensions, mm tandard 6V C 164-TXBC hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound 6V DC 164-TXBDC b () a (+) 12 to V C/DC 164-TXB 6 (max.) 7 21 F to 48V C/DC 164-TXBF Terminal: Tab/solder type 10 Maximum panel thickness for the buzzers with washers is 5mm oud sound 6V C 6V DC 164-TX1BC 164-TX1BDC hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound b () 12 to V C/DC 164-TX1B a (+) 5 (max.) F to 48V C/DC 164-TX1BF oud sound with volume control 6V C/DC 164-TX2B hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound Volume Clockwise: Increase sound pressure Counterclockwise: Decrease sound pressure 12 to V C/DC 164-TX2B F to 48V C/DC 164-TX2BF Panel thickness 5 (max.) D (red) tandard sound with volume control (IP54) 6V C/DC 165-XB Volume Clockwise: Increase sound pressure Counterclockwise: Decrease sound pressure hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound 12 to V C/DC 165-XB Panel thickness 5 (max.) F to 48V C/DC 165-XBF ø /6 Fuji lectric F Components & ystems Co., td./d & C Catalog

27 Numerical Indicators 164 and 165 Numerical indicators Display Input logic Operating voltage Description 164 type 165(oil-tight) type Dimensions, mm Without decimal decoder node 164-T 165-T Terminal ø1 5 (max.) 5.6 P-165 Cathode 164-T C 165-T C With decimal decoder (5, 12, V) F87-3 Positive (ow active) 5V DC 5V DC 12V DC V DC Decoder type: 7447 Decoder type: TC1 164-TC4 164-TC4 164-TC4 B C 165-TC1 165-TC4 165-TC4 165-TC4 B C 12 4 Terminal ø0.8 5 (max.) With decimal decoder (V) Positive V DC Decoder type: TC4 -K 165-TC4 -K Without connector F Negative 164-TC4 -NK 165-TC4 -NK With sign decoder (±1 display) Positive V DC Decoder type: TC4-1K 165-TC4-1K With connector Terminal ø (max.) F Negative 164-TC4-1NK 165-TC4-1NK ø uminous color eplace the mark by the luminous color code : ed G: Green Connector eplace the mark by the connector code Blank: Without connector 1: With connector Fuji lectric F Components & ystems Co., td./d & C Catalog /7

28 Numerical Indicators 164 and 165 Without decoder, with decoder (5, 12 V) Wiring diagrams Without decoder/164-t, 165-T With decoder (5, 12, V) / 164-TC1, 165-TC1, 164-TC4, 165-TC4 DP c g b com a f com e d node common (7seg.D) a f b e d g c DP 7seg. decoder Terminal 164-TC1 No. 165-TC1 164-TC4 165-TC4 10 VCC(5v) VDD(5,12,V) B BCD C code D T BI/BO BI GND (0V) D.P B BCD C code D T BI Vss (0V) D.P a f b e g c d DP The illustration shows the anode common type. The D of the cathode common type is connected in the opposite direction. Note: s shown in the illustration, the structure of the T type consists of a 7-segment D provided with a casing only. imilar to a standard single 7-segment D, use the T type with a current limiting resistor connected Truth value chart 164-TC1, 165-TC1 BCD input (positive) D C B Note: Input BI BI/BO (OUT) Operates independently from and signals. T Display xtinguish xtinguish xtinguish 164-TC4, 165-TC4 BCD input (positive) D C B Note: Input BI T Operates independently from and signals. Display xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish atch BCD input voltage Type 164-TC1, 165-TC1 164-TC4, 165-TC4 Input current () Type BI BI/BO 164-TC1, 165-TC1 1.6m max. 2.4m max. Note: When the pin is set to, the D.P. will be lit. /8 Type 164-TC4, 165-TC4 164-TC4 B, 165-TC4 B 164-TC4 C, 165-TC4 C Note: pull-up resistor is built-in. Input voltage 5V 0 to 0.4V 2.4 to 5V 0 to 1.5V 3.5 to 5V BI, T, ±0.6m max. ±0.2m max. ±0.2m max. 12V 0 to 3V 9 to 12V V 0 to 4V 11 to V T 1.6m max. Terminal symbol T (amp Test): ll segments other than the decimal point will turn ON by setting this pin to (i.e., 8 is displayed). BI (ipple Blanking Input): etting this pin to will turn the display OFF when all BCD codes are. BI/BO (Blanking Input/ipple Blanking Output): I/O pin etting this pin to will turn the display OFF regardless of the BCD codes. This pin will be when all BCD codes are. (atch nable): When this pin is set to, data will pass through. When it is set to, data will be retained. Connect this pin to (0V) when not in use. BI (Blanking Input): When this pin is set to, the display will be OFF for all input except T. D.P. (Decimal Point) Fuji lectric F Components & ystems Co., td./d & C Catalog

29 Numerical Indicators 164 and 165 pplication to PC Used with 164-TC1, 165-TC1 164-TC1 B, 165-TC4 B 164-TC1 C, 165-TC4 C Note: Input logic Positive (low active) Output from PC Transistor output (source) PNP Transistor output (sink) NPN vailable, not available s 16 -TC1, -TC4 B, and -TC4 C (5V, 12V, and V models) do not have an inverter circuit inside, use a programmable logic controller, inserting an inverter (reverse) instruction on your program. (ow ctive) With decoder (V) Wiring diagrams With decoder/164-tc4, 165-TC4 With decoder/164-tc4-1, 165-TC Decoder circuit Voltage stabilizer circuit Input circuit Terminal No VDD (V) B C D D.P Vss (0V) BCD code Decoder circuit Voltage stabilizer circuit Input circuit Terminal No VDD (V) B C Vss (0V) BCD code Truth value chart Decimal display Positive Negative Display D C B D C B xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish atch Note: Operates independently from and signals. Terminal symbol. (atch nable): olds the last entry when the positive logic type goes to () and the negative logic type goes to (). D.P (Decimal Point): Displays a decimal point when the positive logic type goes to () and the negative logic goes to (). ±1 display Positive Negative Display C B C B xtinguish xtinguish atch Note: Operates independently from and signals. BCD input voltage 0 to 2V 12 to 30V pplication to PC Used with Input logic 164-TC4 Positive 165-TC4 164-TC4 -N Negative 165-TC4 -N Note: vailable, not available Input current () Positive logic 2m max. Negative logic 4m max. Output from PC Transistor output (source) PNP Transistor output (sink) NPN Fuji lectric F Components & ystems Co., td./d & C Catalog /9

30 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Mounting space Mounting space, mm Pushbuttons and pilot lights xtended round head or lens Flush square head or lens Flush rectangular head or lens Panel cutting ø Panel cutting ø Panel cutting ø Mushroom head Convex square head Convex rectangular head 20 Panel cutting ø Panel cutting ø Panel cutting ø elector switches When mounting the selector switches near the pilot light When mounting the selector switches near each other With transformer Panel cutting ø Panel cutting ø ()* When mounting the JM or JM selector switches near each other ( only) When mounting the JM or JM selector switches near the other selector switch, pushbutton switch and pilot lights Note: *( ) For switch with flush rectangular head * 165-V, V1, V5, V6 7.7±0.1 0 ø ø Note: * Mushroom, convex square, convex rectangular: JM, JM 0 ø Terminal number 164, 165 Type Wiring Illuminated pushbuttons Pushbuttons elector switches (except for JM, JM types) Pilot lights (without transformer) a (+) a (+) b (-) b (-) Terminal position Type number display side b (-) a (+) Type number display side a b /160 Fuji lectric F Components & ystems Co., td./d & C Catalog

31 Pushbuttons/electors/Pilot ights Type number nomenclature Type number nomenclature Pushbuttons, illuminated pushbuttons and pilot lights F 11 3 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator or lens Operator for illuminated pushbutton F: Flush round head F5: Flush round head (lternate) F: Flush square head F5: Flush square head (lternate) : xtended round head 5: xtended round head (lternate) : xtended square head 5: xtended square head (lternate) C: Concave square head C5: Concave square head (lternate) M: Mushroom head YM: Mushroom head with square bezel V: Push-lock, turn-reset YV: Push-lock, turn-reset with square bezel Operator for pushbuttons F: Flush round head F5: Flush round head (lternate) F: Flush square head F5: Flush square head (lternate) : xtended round head 5: xtended round head (lternate) : xtended square head 5: xtended square head (lternate) C: Concave square head C5: Concave square head (lternate) M: Mushroom head YM: Mushroom head with square bezel V: Push-lock, turn-reset YV: Push-lock, turn-reset with square bezel 2: With selector ring Y2: With selector ring with square bezel ens for pilot lights Z: Flush round Z: Flush square Z: xtended round Z: xtended square ➂ Color of button or lens Code G B Y W O Color Green ed Black* Yellow White Blue Orange Notes: ( ): indicates luminous color * Not available for illuminated types ➃ Contact arrangement (except pilot lights) 11: 22: 33: ➄ amp voltage ➅ Type of lamp Blank: Incandescent 1: Neon 3: Flat D ➆ Terminal Blank: older/tab W: Wire-wrap Button D Incandescent (Orange) (mber) Code D Incandescent Neon B K M P 5V DC 6V DC 12V DC V DC 5V C/DC 12V C/DC V C/DC Neon (Orange) (Orange) (Orange) (Green) 110V C 120V C 220V C 0V C Fuji lectric F Components & ystems Co., td./d & C Catalog /161

32 Pushbuttons/electors/Pilot ights Type number nomenclature Type number nomenclature elector switches J 2 B 11 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator Knob and key type 2-position (operating angle 90 ) P: Knob YP: Knob with square bezel J: Key YJ: Key with square bezel 3-position (operating angle 45 ) P: Knob YP: Knob with square bezel J: Key YJ: Key with square bezel ever type 2-position (operating angle 45 ) : ever : ever with square bezel Note: The operation angle is 45 on the upper and lower side. ➂ Operation 2: 2-position, maintained 0: 2-position, spring return* 3: 3-position, maintained 6: 3-position, spring/manual return (eft to center) 7: 3-position, spring/manual return (ight to center) 1: 3-position, spring return Note: * xcept for and types ➃ Color of knob, lever or key removable position Color of knob or lever B: Black Key removable position Code 2-position 3-position B C D F G Illuminated selector switches P 2 G 11 3 ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator 2-position (operating angle 90 ) P: Knob 3-position (operating angle 45 ) P: Knob ➂ Operation 2: 2-position, maintained 3: 3-position, maintained ➃ Color of knob Code G Y W O Color Green ed Yellow White Blue Orange D (Orange) (mber) Notes: ( ): indicates luminous color The part other than the arrow of the knob is black. ➄ Contact arrangement 11: * 22: Note: * xcept for 3-position ➅ amp voltage Incandescent Code D Incandescent Neon B K M P 5V DC 6V DC 12V DC V DC ➆ Type of lamp Blank: Incandescent 1: Neon 3: Flat D Note: Terminal with solder/tab only 5V C/DC 12V C/DC V C/DC Neon (Orange) (Orange) (Orange) (Green) 110V C 120V C 220V C 0V C ➄ Contact arrangement 11: * 22: 33: Note: * xcept for 3-position ➅ Key type No. (standard), B, C, D,, F ➆ Terminal Blank: older/tab W: Wire-wrap /162 Fuji lectric F Components & ystems Co., td./d & C Catalog

33 Pushbuttons/electors/Pilot ights atings and specifications tandards approved U508 C C22.2 No.14 TÜV: N File No File No. 279 (except for 165-2Z, 2Z, 2Z, 2Z) File No (for 165-2Z, 2Z, 2Z, 2Z) Pushbutton, illuminated pushbutton: elector (except for 165-2, ), illuminated selector: elector (for 165-2, ): Pilot lights: pecifications (Indoor use) Item ated insulation voltage 250V C/DC mbient temperature 10 to +70 C * 1 (no condensation or no icing) umidity 45 to 85% (at 5 to +40 C), no condensation or no icing Durability Mechanical Pushbutton and illuminated pushubutton switch (operations) Momentary action: 1 million lternate action: 250,000 Push-lock, turn-reset: 100,000 With selector ring: 250,000 elector and illuminated selector switch: 250,000* 2 lectrical 100,000 (220V C 0.7) Dielectric strength 2000V C, 1 minute (Between lamp and contact terminals: 00V C, 1 minute) Conditional short-circuit current 1000 hort-circuit protective device Fuse 1 Pollution degree 3 Vibration esonance: 10 to 55z, double amplitude 0.1mm Constant: 16.7z, double amplitude 3mm hock Malfunction durability: 100m/s 2 Mechanical durability: 500m/s 2 Operating frequency 1200 operation/hour (on-load factor: 40%) Insulation resistance 100MΩ or more (500V DC megger) Operator protection IP65 Notes: * 1 For illuminated pushbutton, illuminated selector switch and pilot light: 10 to +55 C * 2 Key insertion/removal durability for selector switch key types: 10,000 Contact ratings ee page /141 amp ratings ated operational voltage 5V 6V 12V V 110V 120V 220V 0V Consumption D DC 14m (Yellow: 28m) 14m (Yellow: 28m) 14m 14m Incandescent C/DC 0.45W (6V) 0.55W (14V) 0.55W (28V) Neon C 0.19V 0.21V 0.38V 0.42V Notes: For the incandescent lamps, the values in parentheses indicate the rated voltage of the lamps. Contact reliability FUJI has confirmed that the unit can be used in 1m circuit conditions at 5V C or DC. The operable range may vary depending on the ambient conditions and type of load. Fuji lectric F Components & ystems Co., td./d & C Catalog /163

34 Illuminated Pushbutton witches Illuminated pushbutton switches Operator amp Voltage Contact Momentary action Type Flush round head F xtended round head F Mushroom head F Mushroom head with square bezel F Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C Note: eplace the mark by the following color code, see page / F F F F F F F F F F11M F22M F33M M M M M M M M M M M M M M11M M22M M33M YM YM YM YM YM YM YM YM YM YM11M YM22M YM33M1 lternate action Type 165-2F F F F F F F F F F511M F522M F533M M M M1 Dimensions, mm 1 to 5 1 to ø20 ø25 1 to 5 1 to ø20 ø ø32 ø32 25sq. /164 Fuji lectric F Components & ystems Co., td./d & C Catalog

35 Illuminated Pushbutton witches Illuminated pushbutton switches Operator amp Voltage Contact Momentary action Type Flush square head F xtended square head F Concave square head F Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C Note: eplace the mark by the following color code, see page / F F F F F F F F F F11M F22M F33M M M M C C C C C C C C C C11M C22M C33M1 lternate action Type 165-2F F F F F F F F F F511M F522M F533M M M M C C C C C C C C C C511M C522M C533M1 Dimensions, mm 1 to 5 1 to sq. 1 to sq sq sq. 20sq. 20sq. Fuji lectric F Components & ystems Co., td./d & C Catalog /165

36 Illuminated Pushbutton witches Illuminated pushbutton switches Operator amp Voltage Contact Type Dimensions, mm Push-lock, turn-reset F Push-lock, turn-reset with square bezel F87-2 Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C 165-2V V V V V V V V V V11M V22M V33M YV YV YV YV YV YV YV YV YV YV11M YV22M YV33M1 1 to 5 1 to ø32 ø32 25sq. Button color eplace the mark by the following button color code Color Green ed White Yellow Blue Orange Code G W Y O With wire-wrap pin terminals have a depth of 47mm. white illuminated pushbutton is fitted with a transparent color lens. The color lens is made of a tinted transparent material. amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Neon 120V C 0V C /166 Fuji lectric F Components & ystems Co., td./d & C Catalog

37 Pushbutton witches Pushbutton switches Operator Contact Momentary action Type Flush round head 165-2F11 lternate action Type 165-2F511 Dimensions, mm 1 to F F522 F F F ø20 ø25 Flush square head 165-2F F511 1 to F F522 20sq. F F F sq. xtended round head to F ø20 ø25 xtended square head to sq. F sq. Concave square head 165-2C C511 1 to C C522 F C C sq sq. Mushroom head 165-2M11 1 to M22 ø32 F M Mushroom head with square bezel 165-2YM11 1 to YM22 ø32 F YM sq. Note: eplace the mark by the following color code, see page /168. Fuji lectric F Components & ystems Co., td./d & C Catalog /167

38 Pushbutton witches Pushbutton switches Operator Contact Type Dimensions, mm With selector ring to 5 90 ø25 F ø20 22 With selector ring with square bezel 165-2Y222 1 to 5 90 ø25 F ø sq. Push-lock, turn-reset 165-2V11 1 to V22 ø32 F V Push-lock, turn-reset with square bezel 165-2YV11 1 to YV22 ø32 F YV sq. Button color eplace the mark by the following button color code Color Code Green G ed Black B White W Blue Contact arrangement and operator position 165-2, 2Y ing eft ight Yellow Y Orange O The color lens is made of a tinted transparent material. (xcept for M, YM, V, YV, types) white pushbutton is fitted with a transparent color lens. black pushbutton consists of a transparent color lens and an attached black legend plate. (xcept for M, YM, V, YV, types) With wire-wrap pin terminals have a depth of 47mm. Terminal number and contact block position Type number display side Button Free U U Upper ➂➀ ➁➃ NC NO ower Depressed U: Upper contact block : ower contact block /168 Fuji lectric F Components & ystems Co., td./d & C Catalog

39 elector witches elector switches/2-position (90-degree) Operator Operation Key removable position Knob Maintained Knob Key Key with square bezel F F F F pring return Maintained pring return Maintained pring return Maintained pring return B D B D Contact Type Dimensions, mm 165-2P2B P2B P2B P0B P0B P0B YP2B YP2B YP2B YP0B YP0B YP0B J J J J2B J2B J2B J2D J2D J2D J J J YJ YJ YJ YJ2B YJ2B YJ2B YJ2D YJ2D YJ2D YJ YJ YJ033 1 to 5 1 to 5 1 to to ø25 25sq. ø25 25sq. The key can be removed only at the following positions: : B: D: For spring-return selector switches, the key can be removed at position. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. Terminal number and contact block position Type number display side ➂➀ ➁➃ NC NO Upper Middle ower Contact arrangement and operator positions: 2-position Contact arrangement Operator position eft ight U: Upper contact block M: Middle contact block : ower contact block M M U U U M U M Contact arrangement (terminal No.: common) : Middle : Upper, lower : Upper, middle, lower Fuji lectric F Components & ystems Co., td./d & C Catalog /169

40 elector witches elector switches/2-position Operator ever ever color Black Operation Contact Type Dimensions, mm 1 to 5 Maintained B B22 45 F B ø25 ever with square bezel Black Maintained B11 1 to B22 45 F B sq. Contact arrangement and operator position 165-2, 2 ever Up Down Terminal number and contact block position Type number display side Contact block M M ➂➀ ➁➃ NC NO Upper Middle ower U U Contact arrangement (terminal No.: common) : Middle : Upper, lower : Upper, middle, lower U M U M U: Upper contact block M: Middle contact block : ower contact block With wire-wrap pin terminals have a depth of 47mm. /170 Fuji lectric F Components & ystems Co., td./d & C Catalog

41 elector witches elector switches/3-position (45-degree) Operator Operation Key removable position Knob Mainteined Knob with square bezel Key Key with square bezel F F F F pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return D C D D C D Contact Type Dimensions, mm 165-2P3B P3B P6B P6B P7B P7B P1B P1B YP3B YP3B YP6B YP6B YP7B YP7B YP1B YP1B J J J J J3D J3D J3C J3C J J J6D J6D J J J J J J YJ YJ YJ YJ YJ3D YJ3D YJ3C YJ3C YJ YJ YJ6D YJ6D YJ YJ YJ YJ YJ YJ133 1 to 5 1 to 5 1 to to ø25 25sq. ø25 25sq. The Key can be removed at the following positions: : B: C: D: : F: G: For spring-return selector switches, the key can be removed only at position. For manual/spring-return selector switches, the key can be removed at positions D, and F for type J6, and position, and G for type J7. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. Fuji lectric F Components & ystems Co., td./d & C Catalog Contact arrangement and operator positions: Contact arrangement Operator eft position 3 Center ight U U 2 1 M U: Upper contact block M: Middle contact block : ower contact block Contact block positions: ee page /170 /171

42 elector witches Illuminated selector switches Operator Operation amp voltage No. of positions Contact Type Dimensions, mm Knob F Maintained Flat D V DC Incandescent V C/DC Neon 110V C Neon 220V C NO+2NC 165-2P P P P P P P P P P211M P222M P322M1 22 ø20 ø25 Knob color (arrow) eplace the mark by the following color code Contact arrangement and operator positions: 2-position Color Code Green G ed Knob color (arrow) Black White W Blue Yellow Y Orange O Contact arrangement Operator eft position 1 M 2 1 U 2 ight M U amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Neon 120V C 0V C 3-position Contact arrangement Operator eft position U Terminal number and contact block position Type number display side b (-) a (+) ➂➀ ➁➃ NC NO Upper Middle ower Contact arrangement (terminal No.: common) : Middle : Upper, lower Center ight U: Upper contact block M: Middle contact block : ower contact block U U /172 Fuji lectric F Components & ystems Co., td./d & C Catalog

43 Pilot ights Pilot lights ens amp Voltage Type Dimensions, mm Flush round Flat D V DC 165-2Z3 1 to 5 Incandescent V C/DC 165-2Z a (+) Neon 110V C 165-2Z1 b (-) F V C 165-2ZM ø20 ø25 Flush square Flat D V DC 165-2Z3 1 to 5 Incandescent Neon V C/DC 110V C 165-2Z 165-2Z1 a (+) b (-) 20sq. xtended round F Flat D 220V C V DC 165-2ZM Z to 5 25sq. Incandescent V C/DC 165-2Z a (+) Neon 110V C 165-2Z1 b (-) F V C 165-2ZM ø20 ø25 xtended square Flat D V DC 165-2Z3 1 to 5 Incandescent Neon V C/DC 110V C 165-2Z 165-2Z1 a (+) b (-) 20sq. F V C 165-2ZM sq. ens color eplace the mark by the following lens color code Color Code Green G ed White W Yellow Y Blue Orange O amp voltage Voltage other than above is available Code D Incandescent Neon B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC 120V C 0V C The color lens is made of a tinted transparent material. white lens is fitted with a transparent color lens. With wire-wrap pin terminals have a depth of 29mm. Fuji lectric F Components & ystems Co., td./d & C Catalog /173

44 Pushbuttons/electors/Pilot ights Mounting space Mounting space, mm Illuminated pushbuttons, pushbuttons, selector switches, illuminated selector switches and pilot lights ound head quare head Mushroom head Push-lock, turn-reset Panel Panel cutting cutting Panel cutting ø ø ø Terminal number Type Wiring Terminal position Illuminated pushbuttons, Illuminated selector switches a (+) 1 3 b (-) 2 4 Type number display side b (-) Pushbuttons elector swiches a (+) 2 4 Pilot lights (without transformer) a (+) b (-) Type number display side a b /174 Fuji lectric F Components & ystems Co., td./d & C Catalog

45 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Notes on use Notes on use Installation on panel For installation, use dedicated wrench X601. The appropriate tightening torque is 0.6 to 1N cm. The installation sequence is as follows: Pass the operator base through the hole in the panel and secure it by tightening the bezel. Properly position the catch arms of the contact holder and the catch legs of the operator base and push the contact holder onto the operator base. To remove the contact holder, pull it while pressing the catch arms inward. Panel Contact holder Mounting steps of switch with transformer ➀Pass the switch operator through the panel hole and secure with a nut by way of the retainer metal from the front of the panel. ➁lign the position of the catch arm of the contact block holder with that of the catch leg of the switch operator. ngage these two catches by pushing them together. ➂Insert and secure the transformer unit while assembling the contact block holder with the retainer metal. ➃Connect the receptacle terminal with lead wires extending from the transformer to the lamp terminal of the contact block holder. (Be care on the polarity of the D. ed: +, Black: ) ➄Push in and secure the standard accessory Panel etainer metal Contact block holder Catch leg Transformer amp terminal Operator base Catch leg Mounting hole Catch arm Operator Catch leg Mounting hole insulation cover by aligning its position with each terminal. To replace the transformer, remove the transformer by widening the catch leg of the contact block holder. Pay attention not to excessively widen the catch leg. Mounting steps are the same as the above steps ➂, ➃, and ➄. Catch arm eceptacle terminal Insulation cover Operating voltage and rated voltage of incandescent lamps ated voltage 6V 14V 28V (tandard) Operating voltage 4 to 5V 10 to 12V 20 to V Incandescent lamps should be operated at the operating voltages if a lamp service life of 5,000 to 10,000 hours are needed. The ambient temperature must not exceed 30 C if the lamp is used at the rated voltage continuously. Method of replacing lamp Incandescent lamps/d lamps/neon lamps emove the color lens and inner button with a remover X6. Then draw out the lamp with a lamp changer X672. When installing lamps, do it manually and in the reverse order of removing. Products with blue and green Ds The D devices on products with high-brightness (blue and green) Ds are very sensitive to static electricity. When replacing D lamps do not allow static electricity to come into direct contact with the metal frame on the upper side of the D lamp. The D device may be damaged if this part is subjected to static electricity. When installing or removing an D lamp, it is recommended that you use the lamp changer (X672). Metal frame D To replace the lamp of a illuminated pushbutton switch (M,V), remove the button and draw out the oil-tight cap. emover (X6) ecess of the oil-tight cap Then, replace the lamp using a lamp changer (X672) and push the oil-tight cap into its original position with its engaging projection properly adjusted (see the figure below). Installing the protection cover / dust-tight cover, guardring Be careful that the panel thickness does not exceed the following: Protection cover: 2.6mm max. Dust-tight cover: 2.0mm max. Guard ring: 2.5mm max. V M Note: amp of 165-ZM type can not be replaced. ngaging projection of oil-tight cap ngaging recess at the inner end of the switch Fuji lectric F Components & ystems Co., td./d & C Catalog /175

46 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Notes on use Method of replacing color lens To remove the color lens, insert a small screwdriver into the color lens and twist in direction of the arrow. Color lens egend plate creen Color lens ecess For an 165-2, use a small standard screwdriver or a similar tool with a flat end. If one side of the color lens is removed from the screen, insert the screwdriver or a similar tool deeper and remove the color lens together with the screen. creen Color lens Projection eplacing pushbuttons In the case of alternative action type pushbutton switches and illuminated pushbutton switches, be sure not to replace the pushbuttons in their locked state. This could result in internal damage to the mechanism. Description sheet The Fuji description sheet is 25µm thick. If preparing custom description sheets, make sure that the thickness is 0.1mm or less. Contact block To replace a contact block, use removing tool GX012. If excessive force is applied when attempting to open the support legs for the contact block holder, deformation or damage may occur. andling precautions Do not apply torque in excess of 1.0 N m to operate the selectors switch (Type P ). equired operating force of switches is less than 0.1 N m. Do not tap on a pushbutton to turn it ON or OFF, such handling may damage it. Be sure to operate the pushbutton by hand. Key type selector switch Five key types (Type B to Type F) are available besides Type, which is the standard key type. Be sure to use a key with a symbol which is matched with the symbol on the main unit. ymbol on the key ymbol on the main unit Fully insert the key into the main unit before turning the key. The key turning force should not exceed 0.1 N m. Do not pull out or insert the key forcibly. Wiring connections Use a soldering iron with a wattage of not more than 30W and a tip length of more than 20mm. Use a rosin-core solder With a 30W iron complete soldering within 5 seconds, or 10 seconds with a 20W iron. Do not apply external force to the terminals. Do not deform the terminals. Because lead-free solder's melting point is slightly high, soldering work may be difficult. Use a soldering iron whose tip is rather large or whose calorie is rather high. Wires that can be connected Two solid wires with a maximum diameter of 0.8mm (solder) One stranded wire with a maximum area of 0.75mm 2 (solder) Flat connection terminal ( ) 0.5 to 1.25mm 2 ( ) 0.2 to 0.5mm 2 Using contact blocks When using NO and NC contacts in the same contact block, avoid connection that involves opposite polarity or wiring from different types of power supply. For wiring to adjacent terminals, use insulated tubing to prevent short-circuit and to assure isolation. For solder terminals, be careful when connecting thick wires. Do not use too much solder. Wiring to wire-wrap pin terminals elect the appropriate wire sizes and tools from the table below. Wire size Bit leeve Number of effective wraps 0.4mm dia. 3-1-B bout 8 0.5mm dia. 1-1-B bout 6 (0.65mm dia.) (2-) (2-B) (bout 6) Use ordinary wrapping for connection. Wires of 0.65mm dia. must not be used on adjacent terminals. owever, 0.65mm dia. wire can be mixed with 0.4 and 0.5mm dia. wires. Wiring to tab terminals Use receptacles, No Installing lamps in close order When continuously lighting pilot lights or pressing illuminated pushbuttons installed in close order, care must be taken that the ambient temperature does not exceed the rated value. /176 Fuji lectric F Components & ystems Co., td./d & C Catalog

47 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and Notes on use Ds D amp Malfunctioning The D lamp is lit by a very small level of current (approximately 0.01m). Therefore, the it may be erroneously lit by a current leaking from the surge absorption circuit or semiconductor circuit or due to stray capacitance between cables. In that case, provide a countermeasure (e.g., connect a resistor in parallel with the D lamp). Countermeasure for Malfunctioning hunt esistor or C elements connected in parallel amp malfunctions can be prevented by connecting a shunt resistor () or C elements (a capacitor and resistor) in parallel with the D lamp terminal. The resistance and C values vary depending on the model and the operating conditions. xample 1 xample 2 amp Transformer C: Capacitor C : esistor hunt X1 resistor X2 X1 X2 V DC : 10kΩ (1W) 110V C C: 0.33µF (250V C) : 120Ω (0.25W) 220V C C: 0.33µF (250V C) : 120Ω (0.25W) Incoming surge Be careful that since high luminance D products use an element sensitive to static electricity, they may not be lit by an abnormal voltage like surge. torage and operation site Use the unit within the rated operating ambient temperature and humidity ranges. Do not use the enclosed type in places where oil or water is sprayed or where dust accumulates. In places such as these, use the oil-tight type or provide a dust cover. The oil-tight type is evaluated with standard cutting oil and cooling oil applied. The oil-tight type cannot be used with some special oils. Buzzer Noise If the application circuit is likely to generate excessively strong noise, connect a surge absorber (e.,g., FUJI' NC390D, provided that the switch is a V type) in parallel with the buzzer. Place of Use The buzzer does not have a drip-proof construction. Do not use the buzzer in places where oil or water is sprayed or where dust accumulates. If the buzzer is a splash-proof type, it will resist sprays of water. Do not use the buzzer in places that are subject to an excessive amount of corronsive gas. Be careful that the buzzer is likely to sound erroneously due to leakage current or the like. Using a flat D in 48V DC circuit When a flat D lamps having a rated voltage of V DC is used with 48V DC circuit, connect an external resistor of 1,800Ω (2W). Preventing the neon lamp from incorrectly turning ON The neon lamp may incorrectly turn ON due to current leakage or voltage induction. In such a case, connect a shunt resistor in parallel with the lamp. xample) 110V C: 100k (0.25W) 220V C: 50k (2W) If an external surge of 3kV or more may occur, connect a surge absorption element in parallel with the lamp. Numerical indicators To ensure high reliability and long life for the D, design the circuit not to exceed the maximum ratings under any operating conditions. Keep in mind that the display may malfunction or be damaged due to noise in input signals. (TC type) Wire the TC type as shown on the nameplate. The IC may break if the supply voltage is connected in reverse. Keep in mind that the correct display will not appear with negative logic input because the TC type accepts positive logic input. Operation Do not use a hitting or bouncing action to operate the button, or the switch may break. lways operate the switch by hand. Fuji lectric F Components & ystems Co., td./d & C Catalog /177

48 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 ccessories ccessories for 164 and 165 Description Type Description Type Color chips (ound) Color Type /178, 5, Green X631-G 5, Z ed X631- White (For Neon) X631-W Blue X631- Yellow X631-Y Orange X631-O Clear X631-C F-682 For D, Neon Green X653-G Color chips (quare) Color Type, 5, G, Green X632-G G5, F, F5, ed X632- GF, GF5, Z White (For Neon) X632-W Blue X632- Yellow X632-Y Orange X632-O Clear X632-C F-681 For D, Neon Green X653-G Color chips (ectangular) Color Type T, T5, TG Green X633-G TG5, TF, TF5 ed X633- TGF, TGF5, ZT White (For Neon) X633-W Blue X633- Yellow X633-Y Orange X633-O Clear X633-C F-680 For D, Neon Green X653-TG Mushroom head button Color Type M, M5 Green X682-G ed X682- White X682-W Blue X682- Yellow X682-Y Orange X682-O I-40 Black X682-B Convex square head button Color Type M, M5 Green X683-G ed X683- White X683-W Blue X683- Yellow X683-Y Orange X683-O I-43 Black X683-B Convex rectangular head Color Type button TM, TM5 Green X684-G ed X684- White X684-W Blue X684- Yellow X684-Y Orange X684-O I-44 Black X684-B egend sheet -165 ound Type: X6- egend: ON, OFF, UP, DOWN quare Type: X616- egend: ON, OFF, UP, DOWN TT, TOP, OPN CO, UTO, MN, T, POW, V, FWD, IG, OW ectangular Type: X617- egend: ON, OFF, UP, DOWN TT, TOP, UTO, MN, FOWD, V When ordering, specify desired legend in the at the end of ordering code, Transparent blank sheets are also available. Use black oil ink. egend plate Type Color Dimensions, mm (crylic resin) ound X665 White ø12.2 x 0.9 X665-C Transparent X665-B Black -164 quare X666 White 12.2sq. x 0.9 X666-C Transparent X666-B Black ectangular X667 White 12.2 x.2 x 0.9 X667-C Transparent X667-B Black egend plate for spot D Type Dimensions, mm (crylic resin) ound X650 ø12.2 x 0.9 quare X sq. x 0.9 ectangular X x.2 x 0.9 P-113 egend plate for selector switch (2-position) -226 Type: X664 egend: ON-OFF egend: Blank Dimensions, mm: sq. x 0.5 egend plate for symbol mark Mark Type quare ectangular quare I ectangular X666- X667- X666- X667- quare T X666-T F87-74 ectangular X667-T Fuji lectric F Components & ystems Co., td./d & C Catalog

49 Pushbuttons/electors/Pilot ights/buzzers 164 and 165 ccessories Description Protection cover Type For round and square head button Type: X671 For rectangular head button Type: X669 X826 This cover protect against accidental operation. Note: Not used for illuminated pushbuttons with guard. pplicable panel thickness is 2.6mm max. Dimensions, mm 33.2 M X671 ø16.2 X669 ø X Dust-tight cover F91-123, I-41 For round and square head button Type: X822 Dimensions, mm: sq. x 14.2 For rectangular head button Type: X668 Dimensions, mm: x 30 x 14.2 For mushroom head button Type: X649 Dimensions, mm: ø30 x These covers protect against dust. Note: pplicable panel thickness is 2.0mm max. Guard ring Type Color Dimensions, mm X676-B Black ø21 x 12 X676-GY Gray I-42 This guard ring is used in combination with an extended round head pushbutton ( or ). Note: pplicable panel thickness is 2.5mm max. Please place an order for a packing (X685) separately when you intend to use for 165 series. Transformer Voltage Type amp 100 to 110V C X805- D 200 to 220V C X805-M F to 110V C X806- Incandescent 200 to 220V C X806-M Fuji lectric F Components & ystems Co., td./d & C Catalog /179

50 Pushbuttons/electors/Pilot ights/buzzers ccessories ccessories for Description Type Description Type Color lens (ound) F Color lens (quare) For flush head (Used with 2F, 2F5, 2F, 2F5, 2Z) Color Type Green X26-G ed X26- Yellow X26-Y Blue X26- Orange X26-O Clear X26-C For extended head (Used with 2, 25, 2, 25, 2Z) Color Type Green X2605-G ed X2605- Yellow X2605-Y Blue X2605- Orange X2605-O Clear X2605-C For flush head (Used with 2F, 2F5, 2F, 2F5, 2Z) Color Type Green X2606-G ed X2606- Yellow X2606-Y Blue X2606- Orange X2606-O Clear X2606-C egend plate F F For flush head Color Type Used with White X2609-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2609-C Neon lamp * 2 Black X2609-B Pushbutton * 3 Dimensions, mm: ø * 4 x 0.9 For extended head Color Type Used with White X2610-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2610-C Neon lamp * 2 Black X2610-B Pushbutton * 3 Dimensions, mm: ø * 4 x 4.4 For flush square Color Type Used with White X2611-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2611-C Neon lamp * 2 Black X2611-B Pushbutton * 3 Dimensions, mm: 17sq. x 0.9 For extended square, concave square Color Type Used with White X2612-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2612-C Neon lamp * 2 Black X2612-B Pushbutton * 3 Dimensions, mm: 17sq. x 4.4 * 1 Illuminated pushbutton switches and pilot lights with incandescent lamps or D lamps, Pushbutton switches (excluding). * 2 Illuminated pushbutton switches and pilot lights with neon lamps. * 3 Pushbutton switches (black) * 4 ngraved range: 17mm dia. For extended head (Used with 2, 25, 2, 25, 2Z) Mushroom head button For illuminated pushbuttons (Used with 2M, 2YM) Color Green ed Yellow Blue Orange Clear Type X2607-G X2607- X2607-Y X2607- X2607-O X2607-C Color Green ed White Yellow Blue Orange Type X2614-G X2614- X2614-W X2614-Y X2614- X2614-O For concave head (Used with 2C, 2C5, 2C, 2C5) For non-illuminated pushbuttons (Used with 2M, 2YM) F Color Green ed Yellow Blue Orange Clear Type X2608-G X2608- X2608-Y X2608- X2608-O X2608-C F Color Green ed White Yellow Blue Orange Black Type X2613-G X2613- X2613-W X2613-Y X2613- X2613-O X2613-B /0 Fuji lectric F Components & ystems Co., td./d & C Catalog

51 Pushbuttons/electors/Pilot ights/buzzers ccessories Description Push-lock, turn-reset button Type For illuminated pushbuttons (Used with 2V, 2YV) Color Type Green X2616-G ed X2616- White X2616-W Yellow X2616-Y F Dust-tight cover For pushbuttons (Used with 2V, 2YV) Color Type Green X26-G ed X26- Yellow X26-Y Black X26-B For flush round (Used with 2F, 2F, 2F5, 2F5) Type: X F Key washer For flush square (Used with 2F, 2F, 2F5, 2F5) Type: X These covers protect against dust. Type: X2601 Mounting hole, mm rmax F ø Fuji lectric F Components & ystems Co., td./d & C Catalog /1

52 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and ccessories ccessories for 164, 165 and Description Type Description Type Incandescent lamp Voltage Type Wrench Type: X601 D-9 6V, 0.6W X641 14V, 0.7W X642 28V, 0.7W X When installing a command switch on a panel, this tool is useful for tightening the switch firmly and efficiently. D lamp Voltage Type Terminal cover Type: X2602 F V DC 6V DC 12V DC V DC X695-5 X695-6 X X695- eplace the mark by the luminous color code ed (), Green (G), Orange (O), mber (), Yellow (Y), Blue () Neon lamp Voltage Type uminous color 110V C X655- Green X654- Orange 120V C X655-K Green X654-K Orange 220V C X655-M Green X654-M Orange 0V C X655-P Green P-119 X654-P Orange F Contact block Terminal Type K-1140 Dummy unit K-1141 This cover is used with 164 and 165 and (except pilot lights). Pass the wires through the cover, then mount the cover in position. older/tab Wire-wrap Type: GX002 GX001 GX001W dummy unit is used to fill the space where no contact blocks are installed. For example, two dummy units are used if contact block is installed, and one dummy unit is used if contact blocks are installed. Panel plug Color Type emover Type: GX012 ound Black X622-B IP40 Gray X622-GY IP40 quare Black X644-B IP40 Gray X644-GY IP40 M-334 This tool is used for replacing the contact blocks or dummy units. ectangular Black X645-B IP40 Gray X645-GY IP40 Black X850-B IP65 I-6 amp changer Type: X672 If the switch is fitted with a lamp, use this tool to remove the lamp. The tool is unnecessary when installing a lamp. F emover Type: X6 This tool is used for replacing the color chips or screens. -34 Contact holder remover P-522 Type: X699 This tool is used to remove a contact holder when switches are densely installed. /2 Fuji lectric F Components & ystems Co., td./d & C Catalog

53 Pushbuttons/electors/Pilot ights/buzzers 164, 165 and ccessories Description Type ockets Terminal Type Used with M-1097 older/tab X697- Pushbuttons Wire-wrap X697-W PC board X697-P older/tab X697- Illuminated Wire-wrap X697-W pushbuttons PC board X697-P Contact arrangement is only. xcept for 165-2P types ockets for Terminal Type D older/tab X697-3 Wire-wrap X697-W3 M-1098 Contact arrangement is only. These sockets are used only when D lamps rated for V DC are used under 110V C/DC. xcept for 164, 165 and series pilot lights or 165-2P type. When side-by-side mounting and continuous lighting, note that a socket has higher temperature over the ambient temperature. Dimensions, mm older/tab X697 JPN PC board mounting Pushbuttons 12 8-ø Wire-wrap PC board Illuminated pushbuttons ø JPN X697 JPN X witch X697 JPN PU ocket 50.6 For wiring to wire-wrap pin terminals, select appropriate wire sizes and tool from the table below. Wire size Bit leeve Number of effective wraps 0.4mm dia. 3-1-B bout 8 0.5mm dia. 1-1-B bout 6 (0.65mm dia.) (2-) (2-B) (bout 6) Use ordinary wrapping for connection. Wires of 0.65mm dia. must not be used on adjacent terminals. owever, 0.65mm dia. wire can be mixed with 0.4mm and 0.5mm dia. wires. Fuji lectric F Components & ystems Co., td./d & C Catalog /3