AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/600

Size: px
Start display at page:

Download "AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/600"

Transcription

1 AVK SERIES 55 AND 06 GATE VALVES, DN 450/500/ Introduction The valve has a full and straight bore corresponding to the nominal diameter and can be installed independently of the flow direction. Although vertical installation is preferred, polyacetal shoes on the wedgeguides allow the valves to be installed in the horozontal or vertical position. Flow/pressure limitations outlined below should be observed. The valves are 100% factory tested hydrostatically to EN , PN 10 and PN 16. The valves are suitable for installation under the following conditions: Flow velocity up to 5 m/sec. with max. 16 bar differential pressure across the closed valve. The valves comply with the general standard and market needs regarding installation, dimensions, materials, capacity and strength for large diameter valves, combined with the easy, cost saving operation of smaller valves. The valves have a standard gland flange to ISO 5210 (F16 flange and spindle diameter of Ø40 mm). Various optional extras like bypass, can be supplied factory fitted or supplied in kit form for retrofitting. See data sheet series 55 AND 06 and chapter 2.3 in this manual. The By-Pass system is not necessary for normal valve function, but can be used with advantage, if slow filling, or emptying of the pipe line is required and to ease operation by out balancing the pressure, whrn valve is closed against high pressure. To minimize water hammer the recommended opening speed is min. 3 min. from fully open to fully closed position. The AVK series 55 and 06 gate valves have many applications. IT IS THEREFORE IMPORTANT TO STATE OPERATING TEMPERATURE, PRESSURE, MEDIUM AND OPERATING CONDITIONS WITH ENQUIRIES/ORDERS, SO THE MOST SUITABLE VALVE WILL BE SUPPLIED FOR YOUR SPECIFIC PURPOSE. 1

2 2. Installation AVK series 55 and 06 gate valves are for below ground, chambered or burried installation. The valves must be protected against freezing by insulation, if installed in areas where freezing can be a problem. Ice in the valve or valve bonnet may lead to damage or malfunction. 2.1 Gasket To ensure tightness it is important to select the correct type of gasket for the medium. 2 gaskets with the correct flange size must be used. Torque/compression information must be obtained from the gasket supplier Bolts Table 1 Bolts DN Work pressure (bar) mm PN 10 PN 16 Quantity 450 M 24 M 27 20* 500 M 24 M 30 20* 600 M 27 M 33 20* * 2 pcs. 150 threaded rods are to be used in case bolt can not be mounted from maiden flange side around by-pass assembly series Installation and tightening The flanges should be cleaned before installation. The valve is placed between the pipe flanges and the bolts inserted. Tighten bolts loosely. Tighten bolts in a diagonal sequence (see below) to ensure flanges are pulled parallel. 2

3 Finally, tighten bolts to maximum torque levels given in table below, note that the gasket supplier must inform of the correct torque. Therefore the torques are only to be taken as a guideline: Table 2 Max. bolt torque Dimension Torque (Nm) M M M M Mounting of a By-Pass system IMPORTANT! Before mounting of a By-Pass system the main valve must not be under pressure, and the medium must be under the level of the By-Pass inlet on the side of the valve. Preparation of the main valve The 2 blind flanges / blind caps on the By-Pass bosses are removed and the inlet area of the valve are thoroughly cleaned for dirt and impurities. 3

4 Preparation of a By-Pass system for series 55. The 16 studbolts are screwed into the two cast iron bends, 8 pcs. in each, and the bends are fitted to the By-Pass valve, together with the mating gaskets (see drawing). The nuts are loosely fastened to ensure that the bends can move freely in relation to the valve. Mounting Series 55 by-pass (picture below): The By-Pass system is mounted on the main valve together with the cleaned gaskets (new gaskets are reccomended), and the previously removed nuts and washers are re-used for fastening. All nuts are in principle tightened as shown on the drawing under chapter The nuts are to be tightened with approx 100 Nm. The By-Pass system is now ready for use. Mounting Series 06 by-pass: The by-pass is mounted in the holes on the side of the valve. Check by-pass bend for lubrication on o-rings before mounting. Mount the by-pass valve between the bend loosely. Mount the bracket plate to secure the bend in the valve. Torque the bracket plate bolts to approx. 80 Nm. Torque the bolts/nuts on the valve flanges with approx. 100 Nm. The bypass is now ready for use. 3. Operation The valve can only be used as an ON/OFF valve. Therefore the valve must be FULLY opened or fully closed during operation Right hand closing valves, CTC valves. 4

5 Closing From factory the valve is delivered with the wedge in almost closed position. By manual operation the valve is closed by turning the handwheel clockwise until the valve is completely closed. For closing torque by manual operation see table 3. Valves with actuators are closed by adjusting the actuator, so that the output shaft moves clockwise in the actuator closing direction. The on/off torque switch should be adjusted, so that the valve is not closed/opened with a higher torque than indicated in table 3. Going to closed position the actuator shall be switched off by means of the on/off torque switch, not the limit switch. The limit switch can be used as alarm indication in close direction by setting it 10 mm above fully closed. See later description of typical operation with electric actuator Opening By manual operation the valve is opened by turning the handwheel anti-clockwise until the wedge is fully open. Valves with actuators are opened by adjusting the actuator, so that the output shaft moves anti-clockwise in the actuator opening direction. The on/off torque switch shall be adjusted, applying an opening torque of 500 to 700 Nm. Going to open position the actuator shall be switched off by means of the on/off limit switch. The limit switch shall in open position be set to 1 (one) revolution before fully open Left-hand closing valves, CTO valves. IMPORTANT! From factory the valve is delivered with the wedge in almost closed position. By manual operation the valve is closed by turning the handwheel anti-clockwise until the valve is completely closed, for closing torque by manual operation see table 3. 5

6 Valves with actuators are closed by adjusting the actuator, so that the output shaft moves anti-clockwise in the actuator closing direction. The on/off torque switch should be adjusted, so that the valve is not closed/opened with a higher torque than indicated in table 3. Going to closed position the actuator shall be switched off by means of the on/off torque switch, not the limit switch. The limit switch can be used as alarm indication in close direction by setting it 10 mm above fully closed. See later description of typical operation with electric actuator. Table 3 Max. closing Turns Free running Rupture DN torque (Nm) to open torque (Nm) torque (Nm) (pressureless) */500** */500** */700** * Series 06 ** Series 55 For electric actuators the recommended opening speed is min. 3 min. corresponding to max. 19 turns/min Opening By manual operation the valve is opened by turning the handwheel clockwise until the wedge is fully open. Valves with actuators are opened by adjusting the actuator, so that the output shaft moves clockwise in the actuator opening direction. The on/off torque switch shall be adjusted, applying an opening torque of 500 to 700 Nm in the fully open position. Going to open position the actuator shall be switched off by means of the limit switch. The limit switch shall in open position be set to 1 (one) revolution before fully open. 6

7 Please note the phase follow is important since wrong phase will cause stall torque to open, thus causing permanent damage to the valve!!! Wiring diagram recommended by AVK is to be found on the last page in this installation manual. If any doubt please contact nearest AVK sales outlet Marking The valves are marked with a label, stating general information such as testing, application etc. 4. Maintenance 4.1. General If the valve is installed according to AVK's instructions, it is maintenance-free. However every 4-5 months it is recommended if possible: 1) To make a routine check of the valve for leaks around the stem and the flange gaskets. All seals will in the course of time be influenced by air and sunlight, and careful checks can reveal such leaks. 2) To adjust the bolts in the flange connections as the compression of the flange gaskets may relax in the course of time and thus leaks may arise. Please observe the bolt torques and sequence table under chapter Replacement of stem sealing AVK valves are factory lubricated and maintenance-free. If it should be necessary to exchange the stem seal the following procedure must be observed. 7

8 Before replacement Before replacement, the valve size should be advised to supplier. A gasket set will be delivered consisting of: - 1 wiper ring - 2 internal stem seal O-rings - 1 gland flange O-ring - 1 nylon bearing Disassembling Important! Before replacement of the stem sealing the valve must be fully opened and not be under pressure. This is done by turning the handwheel in opening direction until impact. It is very important to ensure that the wedge is fully open. 1) The 4 gland flange bolts (pos. 3) are unscrewed and the gland flange (pos. 6) is lifted out and pulled off the stem. 2) Wiper ring (pos. 1), O-rings (pos. 2, 5) and bearing (pos. 4) are carefully removed without damaging the gland flange. 8

9 Assembling 1) The internal surfaces of the gland flange are cleaned and checked for damages. 2) The new O-rings, wiper ring and plastic bearing are lubricated all over with a thin layer of silicone grease (e.g. ROCOL : Mx 22) 3) Wiper ring, plastic bearing and O-rings are carefully fitted in the cleaned gland flange (see figure) 4) Stem are cleaned and checked for damages. 5) The stem is applied a thin layer of silicone grease (e.g. ROCOL : Mx 22) 6) The gland flange is fitted on the valve and fixed with the 4 gland flange bolts (pos. 3). Please ensure that the O-ring (pos. 5) is correctly mounted in the recess. The bolts are tightened with a torque of 100 Nm. 7) The valve can be closed again by turning the handwheel in closing direction. 9

10

11 AVK product number AVK International A/S/ GB

KEYSTONE Figure 990/991 Butterfly valves Installation, operation and maintenance instructions

KEYSTONE Figure 990/991 Butterfly valves Installation, operation and maintenance instructions Before installation these instructions must be fully read and understood Potentially dangerous practices: disregarding instructions improper use of product use of insufficiently qualified personnel Application

More information

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP BALL VALVES TABLE OF CONTENTS MAINTENANCE AND INSTALLATION INSTRUCTIONS 1. 2. 2.1 2.2 2.3 2.4 GENERAL...Page 1 HANDLING...1 Receiving and Storing...1

More information

INSTALLATION, OPERATION & MAINTENANCE MANUAL. 0.- Description Handling Installation Actuators Maintenance...

INSTALLATION, OPERATION & MAINTENANCE MANUAL. 0.- Description Handling Installation Actuators Maintenance... INSTALLATION, OPERATION & MAINTENANCE MANUAL INDEX Page 0- Description 2 1- Handling 2 2- Installation 2 3- Actuators 5 4- Maintenance 5 41- Gland packing replacement 5 42- Seal replacement 6 43- Gasket

More information

Instructions for installation, operation and maintenance of: GATE VALVE

Instructions for installation, operation and maintenance of: GATE VALVE Instructions for installation, operation and maintenance of: GATE VALVE GEN GAC GAF/GENF TERMOVENT SC Temerin Republic of Serbia Instruction for installation, operation and maintenance: Table of Contents

More information

OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE

OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE INDEX SERIES 2500 DUCTILE IRON RESILIENT WEDGE GATE VALVE OPERATION and MAINTENANCE MANUAL. OPERATION AND MAINTENANCE Operation,

More information

YARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000

YARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000 Direct contact and metal-to-metal seating make this Y-pattern globe stop valve ideal for most shut-off applications. FEATURES All valves feature integral Stellite hardfacing on both body and disc seating

More information

DeZURIK " BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT

DeZURIK  BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT DeZURIK 20 144" BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT Instruction D10373 April 2017 Instructions These instructions provide information about the 20 (250 F2 model only) and the 24-144 BAW

More information

INSTALLATION, OPERATION & MAINTENANCE MANUAL Description Handling Installation Actuators...

INSTALLATION, OPERATION & MAINTENANCE MANUAL Description Handling Installation Actuators... INSTALLATION, OPERATION & MAINTENANCE MANUAL INDEX Page 0 - Description 2 1 - Handling 2 2 - Installation 2 3 - Actuators 5 4 - Maintenance 5 41 - Gland packing replacement 6 42 - Seal replacement 6 43

More information

Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator

Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator Operating Instructions ROCO Butterfly Valve with SKG Slider-crank Mechanism, with Electric Multi-turn Actuator 1 Product and Performance Description 2 Design Features of ROCO Butterfly Valve 3 Installation

More information

KENNEDY VALVE RESILIENT WEDGE GATE VALVE MAINTENANCE MANUAL

KENNEDY VALVE RESILIENT WEDGE GATE VALVE MAINTENANCE MANUAL KENNEDY VALVE Division of McWane, Inc. 1021 East Water Street P.O. Box 931 Elmira, New York 14902-0931 Telephone (607) 734-2211 Fax (607) 734-1003 KENNEDY VALVE RESILIENT WEDGE GATE VALVE MAINTENANCE MANUAL

More information

Technical changes kept in reserve INSTALLATION, OPERATION & MAINTENANCE MANUAL. 0.- Description Handling Installation...

Technical changes kept in reserve INSTALLATION, OPERATION & MAINTENANCE MANUAL. 0.- Description Handling Installation... INSTALLATION, OPERATION & MAINTENANCE MANUAL INDEX Page 0.- Description...... 2 1.- Handling...... 2 2.- Installation...... 2 3.- Actuators...... 5 4.- Maintenance...... 6 4.1.- Gland packing replacement....

More information

VALVE FEATURES AVAILABLE MODELS LIMITS OF USE IP 67

VALVE FEATURES AVAILABLE MODELS LIMITS OF USE IP 67 VALVE FEATURES The resilient seat gate valve type is dedicated to the shut off of clear water and sewage water pipes. The motorization with the REGADA actuator allows the automation and the remote control

More information

Installation & Operation Manual

Installation & Operation Manual Installation & Operation Manual Thank you for purchasing our AS4795.1 Butterfly Valve. Before installing or operating, please carefully read this manual to know thoroughly how to install or operate. The

More information

PROJECT TITLE : LUSAIL EXPRESSWAY PROJECT CODE : (2012/18) P-003

PROJECT TITLE : LUSAIL EXPRESSWAY PROJECT CODE : (2012/18) P-003 MATERIAL SPECIFICATION COMPARISON SHEET PROJECT TITLE : LUSAIL EXPRESSWA PROJECT CODE : (2012/18) P-003 SUBMITTAL TITLE : MATERIAL APPROVAL MATERIAL SOURCE : UK PROPOSED MATERIAL : ISOLATION VALVES FOR

More information

Sempell High Pressure Stop Valves Model VA510 (DIN)

Sempell High Pressure Stop Valves Model VA510 (DIN) Designed for highest pressure and temperature applications using high alloy or stainless steels. Features T-pattern globe type Body made of forged steel Wear resistant stellite body seat Conical seat with

More information

NAF-Torex butterfly valves Maintenance and installation instructions List of spare parts

NAF-Torex butterfly valves Maintenance and installation instructions List of spare parts NAF-Torex butterfly valves Maintenance and installation instructions List of spare parts Fi 41.42(4)GB 08.01 Contents SAFETY General 1 Lifting 2 Receiving inspection 3 Installation 4 Flange gaskets 5 Starting

More information

Pressure Reducing Valve Type 2114/2415

Pressure Reducing Valve Type 2114/2415 Pressure Reducing Valve Type 2114/2415 Fig. 1 Type 2114/2415 1. Design and principle of operation The Type 2114/2415 Pressure Reducing Valve consists of the Type 2114 Valve and the Type 2415 Actuator.

More information

Mounting and Operating Instructions EB 8053 EN. Series 250 Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8053 EN. Series 250 Type and Type Pneumatic Control Valves Series 250 Type 3252 1 and Type 3252 7 Pneumatic Control Valves Type 3252 High-pressure valve with Type 3277 Pneumatic Actuator and Type 3767 Electropneumatic Positioner Mounting and Operating Instructions

More information

Flow Control. Before installation or maintenance, these instructions must be fully read and understood.

Flow Control. Before installation or maintenance, these instructions must be fully read and understood. Before installation or maintenance, these instructions must be fully read and understood. Please read these instructions carefully. This symbol indicates important messages and safety instructions. Potentially

More information

KLINGER Piston Valves KVN DN PN 16 I/III with valve ring KX-GT Modul

KLINGER Piston Valves KVN DN PN 16 I/III with valve ring KX-GT Modul Page 1 Assembly Instructions and Handling Regulations for KLINGER Piston Valves KVN DN 65 150 PN 16 I/III with valve ring KX-GT Modul DN 125-150 1 Body 2 Bonnet 3 Hand wheel 4 Piston 5 Lantern bush 8 Threaded

More information

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition

More information

Serie 2003/2013. Three-way Control Valve, mixing/diverting. Wörth am Main. Service. Control Valve Division

Serie 2003/2013. Three-way Control Valve, mixing/diverting. Wörth am Main. Service. Control Valve Division Serie 2003/2013 Three-way Control Valve, mixing/diverting Service Preventive maintenance Preventive maintenance primarily consists of making a regular visual inspection of the valve assembly. This can

More information

CAST IRON GATE VALVE WITH THREADED END

CAST IRON GATE VALVE WITH THREADED END CAST IRON GATE VALVE WITH THREADED END 25-50 PN10 16 bar GATE VALVE WITH THREADED END - TECHNICAL INSTRUCTION MANUAL Made by P.Maślanka 20.01.11 MANUFACTURED AND DESIGNED BY Check by J.Karpiński 20.01.11

More information

CAST IRON GATE VALVE WITH THREADED END DN25-50 PFA bar

CAST IRON GATE VALVE WITH THREADED END DN25-50 PFA bar CAST IRON GATE VALVE WITH THREADED END 25-50 PFA 0 6 bar GATE VALVE WITH THREADED END - TECHNICAL INSTRUCTION MANUAL Made by T.Włoch 22.2.205 Check by M.Dyrlaga 22.2.205 Approved by J.Karpiński 22.2.205

More information

2-port ball valves with flanged connection, PN25

2-port ball valves with flanged connection, PN25 s 4 120 ACVATIX 2-port ball valves with flanged connection, PN25 VAF51.. Gray cast iron EN-GJL-250 (HT250) valve body DN 65...150 k vs 63...360 m 3 /h Angle of rotation 90 Flange connection to ISO 7005-2

More information

Valve Series V2001 Three-way Valve Type 3323

Valve Series V2001 Three-way Valve Type 3323 Valve Series V2001 Three-way Valve Type 3323 Fig. 1 Type 3323 Valve with mounted rod-type yoke (partial view) Edition January 1999 Mounting and operating instructions E 8113/8114 EN 1. Design and principle

More information

back to main page Type: Butterfly valves Instructions and Operation Manual Warning! Warning! Danger for life! 1. Intended use Danger for life!

back to main page Type: Butterfly valves Instructions and Operation Manual Warning! Warning! Danger for life! 1. Intended use Danger for life! Instructions and operation manual for butterfly valves This manual is intended to support the users of Herberholz butterfly valves type HRD/HRA, RD/RA, LDKE/LDKF for installation, operation and maintenance

More information

RESILIENT SEATED GATE VALVE FAF 6200

RESILIENT SEATED GATE VALVE FAF 6200 PRODUCTION STANDARTS DN40 DN800 PN 10-16 Design EN 1171 / EN 1074 Connection Face to Face EN 1092-2 / ISO 7005-2 - Flanged EN 558 Series 15 / DIN 3202 F5 Marking EN 19 Tests EN 12266-1 Corrosion Protection

More information

NAF-Duball ball valves Maintenance and installation instructions List of spare parts

NAF-Duball ball valves Maintenance and installation instructions List of spare parts NAF-Duball ball valves Maintenance and installation instructions List of spare parts Fi 41.61(4)GB 08.01 Contents SAFETY General 1 Lifting 2 Receiving inspection 3 Installation 4 Flange gaskets 5 Starting

More information

SEries 41 check valve installation, operation & maintenance manual

SEries 41 check valve installation, operation & maintenance manual Instruction for use Thank you for selecting an AVK product. With correct use, it will give long and reliable service. This manual has been prepared to assist you install, operate and maintain the valve

More information

Installation Operation Maintenance

Installation Operation Maintenance Installation Operation Maintenance www.challengervalves.com.au 1 QAD#IM1015 REVC 3.10.15 Index 1. INTRODUCTION 3 1.1 Design Features 1.2 Flange and Pipe Compatibility 3 1.3 Operating Pressures and Temperatures

More information

The GACHOT V501 gate valve offer the most possible reliability for process and critical applications

The GACHOT V501 gate valve offer the most possible reliability for process and critical applications The GACHOT V501 gate valve offer the most possible reliability for process and critical applications Features Construction complies with NF EN 1984 Straight-through flow and full port Cast body (investment

More information

Uniwat. Resilient Seated Gate Valves

Uniwat. Resilient Seated Gate Valves Uniwat Resilient Seated Gate Valves www.comeval.es Resilent Seated Gate Valves - UNIWAT 504/507 Copyright COMEVAL VALVE SYSTEMS - Data subject to revision - Regularly updated data on www.comeval.es - DS01

More information

series BUTTERFLY VALVE DOUBLE ECCENTRIC FLANGED FAF 3800 PRODUCTION STANDARDS DN100 DN2000 PN Design EN 593 EN ISO Flanged

series BUTTERFLY VALVE DOUBLE ECCENTRIC FLANGED FAF 3800 PRODUCTION STANDARDS DN100 DN2000 PN Design EN 593 EN ISO Flanged PRODUCTION STANDARDS DN100 DN2000 PN 10-16-25 Design EN 593 Connection End Connection EN 1092-2 ISO 7005-2 - Flanged EN 558 Series 14 DIN 3202 F4 Marking EN 19 Tests EN 12266-1 Corrosion Protection Electrostatic

More information

Fig.01 Fig.02 Fig.03. Disassembly & Reassembly Instructions SBV-HP - Page 3

Fig.01 Fig.02 Fig.03. Disassembly & Reassembly Instructions SBV-HP - Page 3 M12A14 WITH FLOATING BACKSEAT 3 Fig.01 Fig.02 Fig.03 Disassembly & Reassembly Instructions SBV-HP - Page 3 M12A14 WITH FLOATING BACKSEAT 3 1. Caution, before any attempt is made to disassemble, verify

More information

When installing the screwed end, socket weld & flanged end valves the following respective procedures shall be followed for better performance.

When installing the screwed end, socket weld & flanged end valves the following respective procedures shall be followed for better performance. 1. Storage LARSEN & TOUBRO LIMITED Page 1 of 5 1.1. All valves are to be stored in fully open position, in order to protect the sphere surface and soft valve seats. 1.2. Before shipping, the inlet and

More information

TECHNICAL MANUAL MT029

TECHNICAL MANUAL MT029 Ed.2008 Rev.B REFLUX 919 TECHNICAL MANUAL MT029 INSTALLATION, COMMISSIONING AND MAINTENANCE ISTRUCTIONS TABLE OF CONTENTS Chapter Page 1. AIM 4 2. DESCRIPTION OF THE VALVE 4 3. IDENTIFICATION OF THE VALVE

More information

Sempell High Pressure Stop Valves Model VA500 (DIN)

Sempell High Pressure Stop Valves Model VA500 (DIN) Designed for the isolation and control of high temperature and high pressure systems, this multipurpose globe valve can be used in a wide variety of applications. Features Type tested (except for material

More information

Typical Feed Water Heater Isolation System.

Typical Feed Water Heater Isolation System. Type AVS 4/5 Typical Feed Water Heater Isolation System. Features and Benefits These valves are designed to bypass high pressure feedwater around a group of heaters in the event of high water level in

More information

DN15 DN250 PN 16. Corrosion Protection

DN15 DN250 PN 16. Corrosion Protection PRODUCTION STANDARTS DN15 DN250 PN 16 Design DIN 3357 Connection EN 1092-2 / ISO 7005-2 Face to Face DN15-DN150: EN558 Series 14 / DIN 3202 F4 DN200-DN250: EN558 Series 27 / DIN 3202 F5 Marking EN 19 Tests

More information

½" to 4" (DN15 to DN100) LEA31 and LEA33 ANSI Control Valves Installation and Maintenance Instructions

½ to 4 (DN15 to DN100) LEA31 and LEA33 ANSI Control Valves Installation and Maintenance Instructions 00050/1 IM-P0-02 CH Issue 1 ½" to " (DN15 to DN100) LEA1 and LEA ANSI Control Valves Installation and Maintenance Instructions 1. Safety 2. Technical details. Installation and commissioning. Maintenance

More information

Operating Guide SBFV (PN16/25) ENGLISH Steel butterfly valve SBFV Page 2. Danfoss VI.IX.A1.02 1

Operating Guide SBFV (PN16/25) ENGLISH Steel butterfly valve SBFV   Page 2. Danfoss VI.IX.A1.02 1 Operating Guide SBFV (PN16/25) ENGLISH Steel butterfly valve SBFV www.danfoss.com Page 2 Danfoss 2016.06 VI.IX.A1.02 1 Table of Contents: 1. OVERVIEW... 3 2. GENERAL... 3 2.1 Safety...3 2.2 Proper use...4

More information

KEYSTONE. Hygienic butterfly valves model F250 & F251 Installation & Maintenance Instructions. 1 Contents 1 Contents 1

KEYSTONE. Hygienic butterfly valves model F250 & F251 Installation & Maintenance Instructions.   1 Contents 1 Contents 1 Installation & Maintenance Instructions KEYSTONE 1 Contents 1 Contents 1 2 Introduction 1 2.1 Valve use 1 2.2. Application area 1 2.3. Incorrect use 1 3. Safety 2 4. Transport and storage 2 5. Installation

More information

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual Before installation these instructions must be fully read and understood Important Before valves are installed or used the following actions are recommended. 1. Valves/parts have to be inspected and thoroughly

More information

V-SEGMENT SERIES V-Port Segment Control Valves (VS/VV/VM) Installation & Maintenance Manual

V-SEGMENT SERIES V-Port Segment Control Valves (VS/VV/VM) Installation & Maintenance Manual CAUTION: 1. For your safety read this manual before installation or servicing. 2. Before installing or servicing, please ensure the line pressure has been relieved, and any hazardous fluids have been drained

More information

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Version with handwheel Mounting and Operating Instructions EB 8039 EN Edition May 2016 Definition of signal

More information

VALVES WITH SA ELECTRIC ACTUATOR

VALVES WITH SA ELECTRIC ACTUATOR 505-507 VALVES WITH SA ELECTRIC ACTUATOR CHARACTERISTICS The 505+SA and 507+SA cast iron ball valves are dedicated to the automatic opening/shut-off of pipes carrying low pressure unloaded common fluids.

More information

Operating Instructions

Operating Instructions Operating Instructions For ABO Butterfly Valves, Series 3 E DN150-400 1. Introduction 2. Safety Instructions 3. Valve Model 4. Transportation and Storage 5. Installation into Piping 6. Pipe Pressure Test

More information

2/2-way Angle Seat Valve, manually operated, for media up to +180 C

2/2-way Angle Seat Valve, manually operated, for media up to +180 C 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel 316L valve body Compact industrial design with long service life /2702 can

More information

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Statements: NIBCO High Performance Butterfly Valves, Series 6822 and 7822, have been designed

More information

Butterfly valves, PN6, PN10, PN16

Butterfly valves, PN6, PN10, PN16 4 131 Butterfly valves, PN6, PN10, PN16 VKF41... Butterfly valves for fitting between counter-flanges Nominal pressures PN6, PN10, PN16 Nodular cast iron GG-20 / GG-25 Metallic tight-closing (end-stop)

More information

IOM Manual. IOM Manual. Series 76/77.

IOM Manual. IOM Manual. Series 76/77. IOM Manual IOM Manual Series 76/77 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free

More information

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves Type 3347-1 and Type 3347-7 Pneumatic Control Valves Type 3347-7, cast body with welding ends Type 3347-7, bar stock body with threaded connections Mounting and Operating Instructions EB 8097 EN Edition

More information

NIBCO INC. WORLD HEADQUARTERS INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS

NIBCO INC. WORLD HEADQUARTERS INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN 46516-4740 USA PHONE: 574.295.3000 FAX: 574.295.3307 WEB: www.nibco.com INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Installation and

More information

INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL BC.

INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL BC. INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL ORBINOX SPAIN PolInd s/n-20270 ANOETA Tel:+34 943 698030 Fax:+34 943 653066 e-mail:orbinox@orbinoxcom ORBINOX CANADA, ORBINOX USA,, ORBINOX BRAZIL, ORBINOX

More information

Gas. VAG EKO plus Gate Valve resilient-seated - short face-to-face length PN 10/16 - DN KAT-A 1032-F4-G

Gas. VAG EKO plus Gate Valve resilient-seated - short face-to-face length PN 10/16 - DN KAT-A 1032-F4-G Gas VAG EKO plus Gate Valve resilient-seated - short face-to-face length Product characteristics and benefits Resilient seated in accordance with EN 1377 (IN 3352 - A) Face-to-face length acc. to EN 55-1,

More information

USER INSTRUCTIONS. Installation Operation Maintenance. NAF Setball SF Ball Sector Valves. Experience In Motion FCD NFENIM A4 09/16

USER INSTRUCTIONS. Installation Operation Maintenance. NAF Setball SF Ball Sector Valves. Experience In Motion FCD NFENIM A4 09/16 USER INSTRUCTIONS NAF Setball SF Ball Sector Valves FCD NFENIM4156-00 A4 09/16 Installation Operation Maintenance Experience In Motion Contents SAFETY 3 1 General 3 2 Lifting 4 3 Receiving Inspection 4

More information

Installation and service instruction

Installation and service instruction Original Installation and service instruction Knife gate valves Original Installation and service instruction Knife gate valves Table of contents A) General... 3 A1 Symbols... 3 A2 Valve destination...

More information

CV-SFS4-PN16 SERIES SLIENT CHECK VALVE, GLOBE TYPE FEATURES SPECIFICATIONS PRODUCT IDENTIFICATION SYSTEM PRODUCT DATA

CV-SFS4-PN16 SERIES SLIENT CHECK VALVE, GLOBE TYPE FEATURES SPECIFICATIONS PRODUCT IDENTIFICATION SYSTEM PRODUCT DATA CV-SFS4-PN16 SERIES SLIENT CHECK VALVE, GLOBE TYPE Silent check function Temperature -10 ~ +120 PRODUCT IDENTIFICATION SYSTEM 2 Disc Ductile iron GGG 40 3 Spring Stainless steel SUS304 4 Bush Bronze 1400

More information

Butterfly valves PN6, PN10, PN16

Butterfly valves PN6, PN10, PN16 4 131 ACVATIX Butterfly valves PN6, PN10, PN16 VKF41.. Grey cast iron housing EN-GJL-2 DN 40 200 k vs 4000 m 3 /h For fitting between PN 6, PN 10, PN 16 counter-flanges to ISO 7005 Metallic tight-closing

More information

2/2-way Angle Seat Valve, manually operated, for media up to +180 C

2/2-way Angle Seat Valve, manually operated, for media up to +180 C 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel valve body Compact industrial design with long service life /2702 can be combined

More information

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP PAGE 1 OF 10 OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP EFFICIENT, EASY OPERATION Air operated pump Wide range of pressures and volumes Easy to operate controls Output pressure

More information

USER INSTRUCTIONS. Installation Operation Maintenance. Valtek Torex TX Control and shut-off valves. Butterfly Valves. Experience In Motion

USER INSTRUCTIONS. Installation Operation Maintenance. Valtek Torex TX Control and shut-off valves. Butterfly Valves. Experience In Motion USER INSTRUCTIONS Valtek Torex TX Control and shut-off valves Butterfly Valves VLEEIM4143-02 09.10 Installation Operation Maintenance Experience In Motion Contents SAFETY General 1 Lifting 2 Receiving

More information

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL BUTTERFLY VALVE 31300 SERIES INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE 1. Overview Read these instructions carefully before starting the valve installation and start-up work. Safe keep the instructions

More information

Mounting and Operating Instructions EB 8222 EN. Type 3310/AT and Type 3310/3278 Pneumatic Control Valves. Type 3310 Segmented Ball Valve

Mounting and Operating Instructions EB 8222 EN. Type 3310/AT and Type 3310/3278 Pneumatic Control Valves. Type 3310 Segmented Ball Valve Type 3310/AT and Type 3310/3278 Pneumatic Control Valves Type 3310 Segmented Ball Valve Fig. 1 Type 3310/3278 with positioner Fig. 2 Type 3310/AT Mounting and Operating Instructions EB 8222 EN Edition

More information

Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN DN

Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN DN Gate valves Gate valve 700 HJ/JJ (GA PN 10-40) PN 10-100 DN 50-150 Admissible operating pressure [bar] at design temperature [ C] Material PN -60-10 20 100 150 200 250 300 350 400 410 420 430 440 450 460

More information

AWWA C504. Double Eccentric AWWA C504

AWWA C504. Double Eccentric AWWA C504 AWWA C504 Double Eccentric AWWA C504 Series 3900F - Flanged with Handwheel or Lever Handle Series 3900MJ - Mechanical Joint with Handwheel or Lever Handle 0418 0318 MODEL 3975F - Butterfly Valve with Manual

More information

Sub Section Title Page No. 1 Introduction 3. 2 Significant Equipment Detail 3. 3 Installation Guidelines 4. 4 Routine Maintenance 4

Sub Section Title Page No. 1 Introduction 3. 2 Significant Equipment Detail 3. 3 Installation Guidelines 4. 4 Routine Maintenance 4 CONTENTS: Sub Section Title Page No 1 Introduction 3 2 Significant Equipment Detail 3 3 Installation Guidelines 4 4 Routine Maintenance 4 5 Disassembly of the Choke Valve 6 Component Inspection 6 7 Reassembly

More information

Type K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong

Type K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong PN 16 100 Gate Valve Butt-Welded, Flanged Data Sheet Edition: EN 9 / 2015 MPOWER Engineering, a.s. Pod vinicí 2028/20, Modřany, 143 00 Praha 4, CZ T: +420 225 371 300, F: +420 225 371 325 E: info@mpowergroup.eu,

More information

Mounting and Operating Instructions EB 5894 EN. Electric control valves with jet pump. Flanged version of valve with jet pump

Mounting and Operating Instructions EB 5894 EN. Electric control valves with jet pump. Flanged version of valve with jet pump Electric control valves with jet pump Type 3267/5824, Type 3267/5825, Type 3267/3374, Type 3267/3274 Pneumatic control valves with jet pump Type 3267-1, Type 3267-7 Flanged version of valve with jet pump

More information

Mounting and operating instructions EB EN. Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K

Mounting and operating instructions EB EN. Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K Special version DN 15 with differential pressure set point p = 0.5 bar Fig. 1 Type 2479/2430 K Mounting and operating

More information

Type Pressure Transmitter with display. Pressure Transmitter. Technical data. DN15-50 Body material. Stainless steel 316L Actuator material

Type Pressure Transmitter with display. Pressure Transmitter. Technical data. DN15-50 Body material. Stainless steel 316L Actuator material 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel 316L valve body Compact industrial design with long service life Excellent

More information

User manual for. Exalto windshield wiper Type 223 BD 12/24 Volt

User manual for. Exalto windshield wiper Type 223 BD 12/24 Volt User manual for Parts Wipers Propulsion Exalto windshield wiper Type 223 BD 12/24 Volt Catalogue no. 2165.30/32/35/40 (12 Volt) Catalogue no. 2166.3032/35/40 (24 Volt) version 6-2007 Copyright 2007: Exalto

More information

Series Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications.

Series Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications. 7 YARWAY Hancock T-Pattern Globe valves Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications Features Heavy integral stellite hardfacing on

More information

Maintenance instruction

Maintenance instruction Maintenance instruction This maintenance instruction is a step-by-step instruction for service and maintenance on Stafsjö s HG valve. Same procedure also applies for HL, HP and HPT. The instruction shall

More information

Operating Instructions. Pneumatic Control Valve Low Temperature. Type Series GS3

Operating Instructions. Pneumatic Control Valve Low Temperature. Type Series GS3 Operating Instructions Pneumatic Control Valve Low Temperature Type 8026 Series GS3 With: Digital Positioner Type 8048 Electro-pneumatic Positioner Type 8047 Pneumatic Positioner Type 8047 Version: 03/2006

More information

Installation and Operating Instructions

Installation and Operating Instructions Original Installation and Operating Instructions Hawle E2 Valve with Flange Outlet, System 2000 or PE Spigot Ends Table of Contents A) General...... 2 A1 Symbols..... 2 A2 Intended use... 2 A3 Labeling...

More information

Operating instructions GEFA / DOMINO valves series AT 200F ATEX II 1D/2DG c

Operating instructions GEFA / DOMINO valves series AT 200F ATEX II 1D/2DG c GEFA / DOMINO valves series AT 200F ATEX II 1D/2DG c Product description The GEFA valves series AT200F are provided for use in the area of solid substances. The valve is usable as a product tight valve.

More information

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321 Valve Series V2001 Globe Valve Type 3321 Fig. 1 Type 3321 Valve with mounted rod-type yoke for pneumatic or electric actuators (partial view) Mounting and Operating Instructions EB 8111/8112 EN Edition

More information

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN Globe Valve Type 3241 Fig. 1 Type 3241 Globe Valve Mounting and Operating Instructions EB 8015-1 EN Edition July 2012 Contents Contents Page 1 Design and principle of operation.................... 4 2

More information

MADE OF STAINLESS... Certificate 3.1

MADE OF STAINLESS... Certificate 3.1 MADE OF STAINLESS... Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 300 Between flanges PN10-10 C + 90 C Max Pressure : 10 Bars up to DN 200 Specifications : Rising rotating

More information

USER INSTRUCTIONS. NAF Trunnball DL Ball Valves. Installation Operation Maintenance. Experience In Motion FCD NFENIM A4 01/15

USER INSTRUCTIONS. NAF Trunnball DL Ball Valves. Installation Operation Maintenance. Experience In Motion FCD NFENIM A4 01/15 USER INSTRUCTIONS NAF Trunnball DL Ball Valves FCD NFENIM4168-01-A4 01/15 Installation Operation Maintenance Experience In Motion Contents SAFETY 3 1 General 3 2 Lifting 4 3 Receiving Inspection 4 4 Installation

More information

DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL

DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL LILLY ENGINEERING COMPANY 217 CATALPA STREET P.O. BOX 173 ITASCA, ILLINOIS 60143 630-773-2222 FAX: 630-773-3443 www.lillyengineering.com

More information

MADE OF STAINLESS... Certificate 3.1

MADE OF STAINLESS... Certificate 3.1 MADE OF STAINLESS... Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 800 Between flanges PN10-10 C for NBR seat ( -15 C for ) + 90 C for NBR seat ( + 110 C for ) Max Pressure

More information

AVK TOTAL CONTROL INSIDE BUILDINGS GENERAL VALVES FOR BUILDING

AVK TOTAL CONTROL INSIDE BUILDINGS GENERAL VALVES FOR BUILDING AVK TOTAL CONTROL INSIDE BUILDINGS GENERAL VALVES FOR BUILDING SERVICE MEMBER OF THE GROUP GATE VALVE RESILIENT SEATED FULLY VULCANIZED WEDGE Product series: S02, S21, S06, S15, S55 Rising stem/non rising

More information

Operating Instructions

Operating Instructions Operating Instructions ERHARD Tilting-Disc Check Valves with weight-loaded lever 1 Safety Aspects 2 Description of Product and Range of Application 3 Design Features Technical Data 4 Performance and Mode

More information

Series Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features

Series Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features General application Designed for ASME boiler and pressure vessel code, section I applications

More information

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM. QAD#IM6055.REVA

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM.  QAD#IM6055.REVA LSSN Butterfly Valve Installation Operation Maintenance Licence Number: 5326 www.challengervalves.com.au 1 Index 1. INTRODUCTION 1.1 Design Features 3 1.2 Flange and Pipe Compatibility 4 1.3 Operating

More information

TEL: Version: KW2

TEL: Version: KW2 WWW.KLAMBON.COM 1 Page Klambon Water is a wholly owned subsidiary of West Rand Engineering (WRE), we are suppliers of valves, fittings and related products to all industries and our service extends to

More information

MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES

MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES Size Range 2 48 ASME Classes 150-2500 *It is recommended that the valve installer is familiar with

More information

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS:

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: G-H, G-HL, G-K, G-KK, G-L, G-LQ, G-LL, GLS, G-Q, G-QS 1 Contents Maintenance Thrust bearing adjustment

More information

Installation and operating manual Quick closing valve (Bellow sealed) LK product no:

Installation and operating manual Quick closing valve (Bellow sealed) LK product no: LK product no: 902002 Article no: 74506 Revision: 2 Contents 1. General information... 3 2. Safety precautions... 3 2.1 Significance of symbols... 3 2.2 Explanatory notes on safety information... 3 3.

More information

USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008

USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008 诲眾 ᓠ 睂睄 睄 ɞ 1/7 ZETKAMA Spółka Akcyjna ul. 3 Maja 12 PL 57-410 Ścinawka Średnia USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008 Date: 01.01.2008 CONTENTS 1. Product description

More information

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Contents Section 1. General Observations... 2 2. Operation... 4 3. Control During Operation... 5 4. Trouble Shooting... 6 5. Maintenance... 7 Please

More information

3. Installation and Commissioning 4. Maintenance 5. Spares

3. Installation and Commissioning 4. Maintenance 5. Spares INSTLLTION ND MINTENNCE INSTRUCTIONS IM-P305-06 US November 2003 1/2" to 4" (DN15 to DN100) KE41, 43, 61, 63, 71 and 73 NSI Control Valves 1. Safety 2. Technical details 3. Installation and Commissioning

More information

VALVES WITH SA03 ELECTRIC ACTUATOR

VALVES WITH SA03 ELECTRIC ACTUATOR 513-514 VALVES WITH SA03 ELECTRIC ACTUATOR CHARACTERISTICS The 513+SA03 L-port and 514+SA03 T-port stainless steel 3-way ball valves are dedicated to the mixing, diverting or automatic discharging of industrial

More information

MUELLER ECCENTRIC PLUG VALVE

MUELLER ECCENTRIC PLUG VALVE MUELLER INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS 1 MUELLER System Design The life of the valve is dependent on its application, frequency of use and freedom from misuse. The properties of the

More information

Butterfly valves PN 16

Butterfly valves PN 16 s 4 119 ACVATIX TM Butterfly valves PN 16 VKF42.. Gray cast iron or nodular cast iron valve body DN 50...600 k vs 65...37,000 m 3 /h For fitting with PN 16 counter-flanges to ISO 7005 Tight-closing in

More information

FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description

FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL Item No.s/Description Item No. Description Material Specification HYDRANT Qty. Req d Item No. Description Material Specification 1 Operating

More information

Mounting and Operating Instructions EB EN. Type 3372 Electropneumatic Actuator. Actuator area: 120 and 350 cm² With Type 3725 Positioner

Mounting and Operating Instructions EB EN. Type 3372 Electropneumatic Actuator. Actuator area: 120 and 350 cm² With Type 3725 Positioner Type 3372 Electropneumatic Actuator Actuator area: 120 and 350 cm² With Type 3725 Positioner Translation of original instructions Type 3372 with 120 cm² actuator area Type 3372 with 350 cm² actuator area

More information