Focus RS Catback
|
|
- Evan Lawrence
- 5 years ago
- Views:
Transcription
1 Focus RS Catback Focus RS Catback Ford Focus RS Congratulations on your purchase of the COBB Tuning Focus RS Catback Exhaust! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician. Table of Contents Table of Contents Parts List Tools Needed Stock Exhaust Removal COBB Cat Back Installation
2 Links Parts List Exhaust Muffler Section with Valve Assembly Exhaust rear mid-pipe Exhaust Front mid-pipe (2) Exhaust Clamps Tools Needed 3/8" ratchet 3/8" 16mm socket 3/8" 12" extension 3/8" 6" extension Stock Exhaust Removal 1. First off park the car in a flat level area and safely lift and support the car. 2. If you have an older car, spray the exhaust hangers with silicon lube in order to loosen them up for easier exhaust removal later. 3. Now you'll need to loosen and remove the front clamp where it meets the factory downpipe. Loosen the clamp using a 16mm socket then remove the clamp from the pipe.
3 4. Go ahead and unplug the connector from the exhaust valve.
4 5. Like the Focus ST, there are two options for removal of the exhaust. One option is to drop the entire rear subframe in order to fish the exhaust out where it goes over the assembly, however this is time consuming and requires a friend and multiple jacks and stands. We opt to cut ours off in the upward slant before it goes over the rear subframe. We typically go back afterwards to add a flange or slip fit to allow it to be reinstalled later if needed. (It also takes up less space in your garage than the entire one piece exhaust assembly which is quite large.
5 6. Once the exhaust is separated, start by removing the exhaust hangers for the rear muffler section one at a time, making sure to support it as you go. 7. Once they're all removed you can swing down the muffler in order to unhook the exhaust where it goes over the rear subframe (depending on where you cut it) and remove it from the car.
6 8. With the rear section out of of the way, undo the hangers from the center exhaust section and remove that as well and set it out of the way.
7 COBB Cat Back Installation 1. Install the clamp onto the end of the front pipe and slide it back. You may need to stretch out the stock exhaust clamp a little bit in order to get it to fit entirely.
8 2. With the front gasket and clamp over the downpipe, roll the mid-pipe and slip the mid-pipe into the hanger making sure to have the slip fit end towards the rear.
9 3. Loosely screw down the clamp between the mid-pipe and downpipe. 4. With an exhaust clamp loose put it over the end of the slip fit and push it away from the connection. 5. Install the middle section of the exhaust into the front pipe section.
10 6. Add another clamp onto the rear section and slide it out of the way of the slip fit. 7. Work the muffler slip fit on to the mid-pipe, sometimes turning it back and forth can get it up and in place. Make sure it seats all the way to prevent exhaust leaks.
11 8. Once the slip fit is seated put it up into the hangers doing one side at a time (the side opposite of where it comes over the subframe is a good place to start so that it can hang somewhat supported by itself when you do the other side.) 9. Get the exhaust centered and lined up the way you want at the rear bumper. 10. Double check the positioning of the mid-pipe. Make sure there is enough room between it and the heat shielding to prevent rattles.
12 Begin tightening the exhaust starting at the front and work to the back. You may need to roll the mid-pipe as you tighten to prevent the clearance from decreasing. Once everything is tightened and lined up the way you want, plug in the factory connector to the new valve in the COBB Cat Back Exhaust.
13 13. You're all done, go out and enjoy! Links Ford Focus RS Map Notes - Reference to help figure out what map you should be on for your modifications Focus RS Catted Downpipe - Installation instructions Customer Support support@cobbtuning.com Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)
COBB Catback Exhaust
591100 COBB Catback Exhaust 2013 Ford Focus ST Congratulations on your purchase of the COBB Catback Exhaust for your 2013 Ford Focus ST. The following instructions will assist you through your installation
More informationCOBB Tuning Catback Exhaust System MAZDASPEED3
572101 COBB Tuning Catback Exhaust System 2010+ MAZDASPEED3 Congratulations on your purchase of the COBB Tuning SS Catback Exhaust System for your 2010+ MAZDASPEED3. The following instructions will assist
More informationTurboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More information5B HIGH FLOW CATTED DOWNPIPES N54 135i/335i
5B1202 - HIGH FLOW CATTED DOWNPIPES N54 135i/335i Installation Instructions Front Downpipe Rear Downpipe Congratulations on your purchase of the COBB High Flow Catted Downpipes for your N54 BMW 135i/335i!
More informationHARD PIPE KIT
701550 HARD PIPE KIT 2014 Ford Fiesta ST Congratulations on your purchase of the COBB Hard Pipe Kit for your 2014+ Ford Fiesta ST. The following instructions will assist you through your installation process.
More informationFocus ST Carbon Fiber Intake
791400 - Focus ST Carbon Fiber Intake 791400 COBB Focus ST Carbon Fiber Intake Congratulations on your purchase of the COBB Tuning Carbon Fiber Intake System! The following instructions will assist you
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More information9F1760/9F1761 COBB Sport Springs Ford Focus ST
9F1760/9F1761 COBB Sport Springs 2013+ Ford Focus ST Installation Instructions Congratulations on your purchase of the COBB Sport Springs for your 2013+ Ford Focus ST. These instructions should only be
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationLightweight Tubular Sway Bar Kit Subaru WRX / STi / 09+ FXT
915250 Lightweight Tubular Sway Bar Kit 2008+ Subaru WRX / STi / 09+ FXT Installation Instructions Congratulations on your purchase of the COBB Lightweight Tubular Sway Bar Kit for your Subaru WRX, STi
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationMK5 Gen2 GTI Exhaust Installation Instructions
MK5 Gen2 GTI Exhaust Installation Instructions Tools Required Wrenches/sockets: 13, 15, 16, 17, 22 mm Flat-blade screwdriver Penetrating lubricant Summary This document includes instructions for the following
More informationPypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & GT) - Installation Instructions
Pypes 409 Stainless Steel Violator Catback with Polished 304 Tips (86-93 LX & 94-97 GT) - Installation Instructions The below installation instructions work for the following products: Pypes 409 Stainless
More informationINSTALLATION INSTRUCTIONS Unitronic Turbo-Back Exhaust System for MK7 GTI UH026-EXA
Unitronic Turbo-Back Exhaust System for MK7 GTI Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included
More informationInstruction Guide: Infiniti Q50 3.0L VR30DDTT "Full Down Pipes"
480 E. Easy St. Unit #4 Simi Valley, Ca. 93065 Instruction Guide: 2016+ Infiniti Q50 3.0L VR30DDTT "Full Down Pipes" Technical support: (805) 522-3278 Monday- Friday 9a.m.- 3 p.m. PST WARNING: INSTALLATION
More informationInstallation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT)
Installation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT) Overview: This installation guide will cover installation of the Borla Stinger S-Type Catback Exhaust for all Mustang GTs from
More information2017+ FORD RAPTOR DOWNPIPE INSTALLATION INSTRUCTIONS
Thanks for purchasing a Stainless Works Downpipe system for your 2017+ Ford Raptor. Our team has done our very best to ensure that this product is the premium in performance, quality, and fitment. We are
More informationINSTALLATION INSTRUCTIONS Unitronic 3 Turbo-Back Exhaust System for Golf R UH021-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationCOBB SPORT SPRINGS
915760 - COBB SPORT SPRINGS 2008-2013 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2008-2013 Subaru WRX/STi. The following instructions will assist you through your
More informationCOBB Tuning Ford Carbon Fiber Air Scoop Focus ST COBB Ford Carbon Fiber Air Scoop Focus ST
791450 - COBB Tuning Ford Carbon Fiber Air Scoop Focus ST 2013-2017 791450 COBB Ford Carbon Fiber Air Scoop 2013-2017 Focus ST Congratulations on your purchase of the COBB Tuning Carbon Fiber Air Scoop!
More informationCOBB 3 SF INTAKE SYSTEM
COBB 3 SF INTAKE SYSTEM 2015 Mustang Ecoboost Congratulations on your purchase of the COBB 3 SF Intake System for your 2015 Mustang Ecoboost. The following instructions will assist you through your installation
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid MazdaSpeed3/Mazdaspeed6 Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions will assist
More informationARK Exhaust System N-II Cat-Back. (SM N) for Chevrolet Camaro (3.6L V6 LLT/LFX, 6.2L V8 LS3/L99)
ARK Exhaust System N-II Cat-Back (SM0403-0011N) for Chevrolet Camaro (3.6L V6 LLT/LFX, 6.2L V8 LS3/L99) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to compete
More informationCOBB SPORT SPRINGS
913760 - COBB SPORT SPRINGS 2004-2007 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2004-2007 Subaru WRX/STi. The following instructions will assist you through your
More informationSaab 9-3 Krona Downpipe Installation Instructions. What's Included:
www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo
More informationINSTALLATION INSTRUCTIONS Unitronic Downpipe for AWD 2.0 TSI Gen3 MQB UH027-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More information2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220
PART #30212 2010 Camaro Long Tube Headers, Coated w/high Flow Cats Use w/#30220 PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM CHECK PART
More informationPypes 409 Stainless Steel Violator Cat-back with Polished 304 Tips Installation Guide (98-04 GT/Mach 1)
Pypes 409 Stainless Steel Violator Cat-back with Polished 304 Tips Installation Guide (98-04 GT/Mach 1) The below installation instructions work for the following products: Pypes 409 Stainless Steel Violator
More informationCAT-BACK EXHAUST FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE WARNING PARTS INCLUDED INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC STAINLESS STEEL RESONATED MIDPIPE W/ 2-BOLT FLANGE 1PC STAINLESS STEEL MIDPIPE-TO-REAR MUFFLER SECTION 1PC STAINLESS STEEL REAR MUFFLER SECTION 1PC 3" DUAL OFFSET TIPS
More informationSLP High Flow Catalytic Converter Kit (96-10) - Installation Instructions
SLP High Flow Catalytic Converter Kit (96-10) - Installation Instructions The below installation instructions work for the following products: SLP High Flow Catalytic Converter Kit (96-10) Please read
More informationARK Exhaust System DT-S Cat-Back. (SM D, 0201D) for Honda CR-Z (1.5L I4 Hybrid LEA)
ARK Exhaust System DT-S Cat-Back (SM0603-0101D, 0201D) for Honda CR-Z (1.5L I4 Hybrid LEA) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand the installation
More informationMagnaflow MF Series Cat-Back Exhaust Dual Side Exit - Before Rear Tire p/n: F150 Extended Cab
Magnaflow MF Series Cat-Back Exhaust Dual Side Exit - Before Rear Tire p/n: 19054 2015-2017 F150 Extended Cab Time Necessary: Approximately 1 hour Please Note: I ran into an issue with my install. This
More information2016 Camaro Header Installation
TEXAS-SPEED.COM 2016 Camaro Header Installation Tools 8mm Socket 11mm Socket 5/8 Spark Plug Socket T15, T35 Torx Bit 5mm Allen Bit 10mm Socket and Wrench 11mm Socket and Wrench 3/8 Drive Ratchet, Torque
More informationExhaust System Installation Turbo Downpipe Audi MKII TT-RS 2.5T CD100028
Please take the time to read and understand installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who has
More informationBMW F8x M3 & M4 Valvetronic Exhaust System
BMW F8x M3 & M4 Valvetronic Exhaust System SKU: FS.BMW.F8X.VLVP Required Tools Hydraulic Lift or Floor Jack & Stands Metric Socket Set w/ Ratchet & Extensions Metric Open-End Wrench Set Inverted Torx Bits
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationARK Exhaust System DT-S Cat-Back with optional Test Pipe. (SM D, 0213D; TP ) for Scion FR-S and Subaru BRZ (2.
ARK Exhaust System DT-S Cat-Back with optional Test Pipe (SM1202-0113D, 0213D; TP1202-0113) for Scion FR-S and Subaru BRZ (2.0L H4 4U-GSE/FA20) Congratulations on purchasing an ARK Performance premium
More informationExhaust System Installation for the Ford Mustang PN s ,140584,140585,140589,140590,140591
Exhaust System Installation for the Ford Mustang PN s-140583,140584,140585,140589,140590,140591 Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years
More informationINSTALLATION INSTRUCTIONS Unitronic 3 Turbo-Back Exhaust System for MK5 Jetta /GLI UH020-EXA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationARK Exhaust System GRiP Cat-Back. (SM G, 0209G, 0309G) for Nissan 370Z (3.7L V6 VQ37VHR)
ARK Exhaust System GRiP Cat-Back (SM0901-0109G, 0209G, 0309G) for Nissan 370Z (3.7L V6 VQ37VHR) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand the installation
More informationCORKSPORT Power Series Cat Back Exhaust I N S T A L L A T I O N I N S T R U C T I O N S Mazda 6 2.5T PART #: ATK
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Power Series Cat Back Exhaust 2018+ Mazda 6 2.5T PART #: ATK-6-101-12 Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT Power
More informationCOBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3
COBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3 Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions should assist you through your installation process. Please
More information15-18 FORD MUSTANG GT
15-18 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationSLP Modular Muffler Installation Guide
SLP Modular Muffler Installation Guide The below installation instructions work for the following products: Ford Mustang Bullet Style SLP Loudmouth II Mufflers Ford Mustang Shotgun-Style SLP Loudmouth
More informationTuned Length Headers. Special Tools Required: Install Time: Difficulty: Follow these instructions carefully to ensure correct fitment and operation.
Special Tools Required: welder / saws all Install Time: Approximately 4 Hours Difficulty: 4 out of 5 Follow these instructions carefully to ensure correct fitment and operation. STEP 1 Disconnect the negative
More informationVolkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions
Volkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust STOP Please take time to read and understand
More information2010 Camaro Long Tube Headers, Coated w/high Flow Cats/ Powerflo-X Crossover Assembly
PART #30213/30214 2010 Camaro Long Tube Headers, Coated w/high Flow Cats/ Powerflo-X Crossover Assembly PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included.
More informationARK Exhaust System GRiP Cat-Back with optional Down Pipe/Test Pipe
ARK Exhaust System GRiP Cat-Back with optional Down Pipe/Test Pipe (SM0702-102G, 202G, 302G; DP0702-0020) for Hyundai Genesis Coupe (2.0L I4 Turbo Theta TCi) Congratulations on purchasing an ARK Performance
More informationHow to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ
Moddit How to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ Written By: Terence Chang 2019 www.moddit.com/ Page 1 of 11 TOOLS: Metric Socket Set- 10mm,12mm,14mm,17mm (1) Metric Combination
More informationCOBB Fuel Pressure Regulator Kit
315100 COBB Fuel Pressure Regulator Kit 2008+ Subaru STI Congratulations on your purchase of the COBB Tuning Fuel Pressure Regulator Kit for your 2008+ Subaru STI. The following instructions will assist
More informationThank you for purchasing the AWE SwitchPath Exhaust System for the Audi B9 S5 Sportback.
Thank you for purchasing the AWE SwitchPath Exhaust System for the 2017+ Audi B9 S5 Sportback. Let s go! Switchpath Exhaust Parts: 1 Driver downpipe upper section (part A10) 1 Driver downpipe lower section
More informationVolkswagen MK5 GTI ECS Valved Exhaust System Installation Instructions
Volkswagen MK5 GTI ECS Valved Exhaust System Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationARK Exhaust System GRiP Cat-Back. (SM G, 0207D, 0307D) for Infiniti FX35 (3.5L V6 VQ35HR)
ARK Exhaust System GRiP Cat-Back (SM1104-0107G, 0207D, 0307D) for Infiniti FX35 (3.5L V6 VQ35HR) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand the
More informationARK Exhaust System GRiP Cat-Back. (SM G, 0207G, 0307G) for Infiniti G37 Coupe AWD (3.7L V6 VQ37VHR)
ARK Exhaust System GRiP Cat-Back (SM1102-0107G, 0207G, 0307G) for Infiniti G37 Coupe AWD (3.7L V6 VQ37VHR) Congratulations on purchasing an ARK Performance premium exhaust system! Please read and understand
More information15-17 FORD MUSTANG GT
15-17 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationPlease take time to read and understand these installation instructions.
Please take time to read and understand these installation instructions. CORSA recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid Mitsubishi Evolution X / Ralliart Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions
More informationIE VW & Audi MQB Performance Cast Downpipe (AWD) Install Guide Part Number: IEEXCK1
IE VW & Audi MQB Performance Cast Downpipe (AWD) Install Guide Part Number: IEEXCK1 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More informationExhaust System Installation for the Ford Mustang PN s , , , , , , , ,
Exhaust System Installation for the Ford Mustang PN s-140583, 140584,1 40585, 140586, 140587, 140588, 140589, 140590, 140591 Precision manufactured using aircraft quality T-304 stainless steel; this system
More information3 Turbo Downpipe Installation Audi A3 / Volkswagen GTI / Volkswagen Jetta 2.0L FSI/TSI Turbo CD100013
Please take time to read and understand these installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationSubaru WRX MRT Turbo Back Exhaust System
2015-16 Subaru WRX MRT Turbo Back Exhaust System Part No. 98P113 STOP Verify that all of the following components are included in kit before beginning installation: Part #1 J-Pipe / Downpipe Part #2 Mid-Pipe
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More information15-17 FORD MUSTANG GT
15-17 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationHIGH FLOW MIDPIPE INSTALLATION INSTRUCTIONS PART NUMBER D APPLICATION: F80 M F82 M4
HIGH FLOW MIDPIPE INSTALLATION INSTRUCTIONS PART NUMBER D660-0060 APPLICATION: 2015-17 F80 M3 2015-17 F82 M4 Congratulations for being selective enough to use a Dinan High Flow Midpipe Kit. We have spent
More informationTENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
Turner Motorsport LLC / 1-800-280-6966 / www.turnermotorsport.com DI/DBM 3/21/16 TENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
More informationFog Lamp Instructions
Fog Lamp Instructions 2011+ Ford Super Duty Congratulations on your purchase of a high quality PUTCO product. Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
More informationInstallation Instructions
Description Contents Revo Test Pipe or Optional Catalytic Converter Pipe Revo Mid Pipe Revo FWD Reducer Pipe Recommended Tools Quantity Tool Size 1 Hex Key / Socket 6 1 Sockets 13 (deep well) 1 Ratchet
More informationBy installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below.
Thank you for purchasing a Borla Performance Cat-back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationSee a picture of each kit on the following page.
Stainless Steel Chevelle/El Camino Dual Exhaust Kit 793-91325 (2.5 ) or 793-91330 (3.0 ) Fits 1968 1972 Chevelle/El Camino Chevy Small Block/Std Port Heads and Dynatech MuscleMaXX Headers (740-33210, 740-43210
More informationInstallation for the Ford Mustang V-6 PN s , ,
Installation for the Ford Mustang V-6 PN s-140586, 140587, 140588 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document
More informationFree Flow Exhaust Installation Instructions
Free Flow Exhaust Installation Instructions PART NUMBER D660-9001 APPLICATION: 2007 328i (E92 only) Thank you for purchasing a Dinan High Performance Muffler! Some mechanical skill is required to install
More informationLG Super Pro Long Tube Headers Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports
LG Super Pro Long Tube Headers Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG headers for your Gen 5 Camaro. Parts Inventory:
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to
More informationJBA Cat4ward Shorty Header Install (05-10 Mustang GT and Bullitt)
JBA Cat4ward Shorty Header Install (05-10 Mustang GT and 08-09 Bullitt) Installation Time: 6-8 Hours (Depending on Tools and Help) Tools Required: 8mm Socket 10 mm Socket 13mm Socket 15mm Deep Socket Ratchet
More informationPart Numbers: Complete Kits: C5 Base/Z06 Complete Header Package with Cats C5 Base/Z06 Complete Header Package without Cats
Product: Corvette Tri-Y Headers & Mid-Pipe Part Numbers: Complete Kits: 1150042 C5 Base/Z06 Complete Header Package with Cats 1150043 C5 Base/Z06 Complete Header Package without Cats Applications: Chevrolet
More informationSE761-E Q7 3.0T Exhaust Installation Guidelines
SE761-E10-01 Q7 3.0T Exhaust Installation Guidelines Q7 3.0T Exhaust Exhaust Kit Installation Applications Description Q7 3.0T Catback Exhaust SE761-E10-01 Warning: Proper clamp placement! Align clamp
More informationExhaust System Installation PN , , , , &
Exhaust System Installation PN-140415, 140416, 140417, 140438, & 140466 BORLA PERFORMANCE INDUSTRIES These instructions have been written to help you with the installation of your Borla Performance Exhaust
More information15-17 FORD MUSTANG GT
15-17 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationBill of Materials: Please take time to read and understand these installation instructions.
Please take time to read and understand these installation instructions. CORSA recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationFactory safe air/fuel ratio s for Optimum performance Patent# 7,359,795
Part Number SP1125 2007-09 BMW 335i 2008-09 BMW135i 3.0L Twin Turbo L6 This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. 1-2 piece air intake
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust STOP Please take time to read and understand
More informationExhaust System Installation for Corvette, C6 or Z06 PN s , 11811, 11812, 11814, 11815, 11816, 11917
Exhaust System Installation for Corvette, C6 or Z06 PN s - 11810, 11811, 11812, 11814, 11815, 11816, 11917 ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D PARTS LIST
ADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D120-0580 DESCRIPTION: Front 28mm; 3-hole adjustable APPLICATION: 2014-16 F22 228i/M235i 2015-16 F23 228i/M235i Convertible 2013-16 F30 320i
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More informationGP113S STAINLESS HEADER WITH STAINLESS Y-PIPE
GP113S STAINLESS HEADER WITH STAINLESS Y-PIPE HAS NO AIR FITTING AT THE FRONT OF EACH MANIFOLD FOR CHEVROLET/GMC 96-00 PICKUP 7.4L 2/4WD 96-00 SUBURBAN 7.4L 2/4WD GIBSON HEADERS ARE 50 STATE SMOG LEGAL
More informationOwner smanual. Banks Monster Exhaust System Ford F L V8, 3.5L & 2.7L EcoBoost ECMB, CCSB & CCMB
Owner smanual with Installation Instructions Banks Monster Exhaust System 2015 Ford F-150 5.0L V8, 3.5L & 2.7L EcoBoost ECMB, CCSB & CCMB THIS MANUAL IS FOR USE WITH SYSTEMS 48762 & 48762-B Gale Banks
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationipd Catback Oval Tube Exhaust System S60R ( ), V70R ( ) ipd #120056
PI-408 02/12 Dedicated to improving vehicle fun, safety & performance Installation Instructions *PI408* ipd Catback Oval Tube Exhaust System S60R (2004-2007), V70R (2004-2007) ipd #120056 SUGGESTED TOOLS
More informationVolkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions
Volkswagen MK6 GTI ECS Valved Exhaust System Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete
More informationBanks Monster Exhaust System
Banks Monster Exhaust System 2007-2008 Chevy/GMC 1500 Silverado 4.8L, 5.3L, 6.0L V-8 Gas, New Body Style THIS MANUAL IS FOR USE WITH MONSTER EXHAUST SYSTEMS 48344, 48345 Gale Banks Engineering 546 Duggan
More informationDetroit Tuned R56 Oil Service How-To
Detroit Tuned R56 Oil Service How-To Welcome to Detroit Tuned s how-to guide for an oil service for an R56 MINI Cooper. It s always best to do an oil change on a hot engine as the hot oil will drain better
More informationEXPANSION TANK PARTS LIST AND INSTALLATION GUIDE
PARTS LIST AND INSTALLATION GUIDE PARTS LIST 1 PC MISHIMOTO RADIATOR 2 PC CAST THERMOSTAT HOUSINGS 1 PC MAGNETIC DRAIN PLUG W/ DOWTY OIL SEAL 4 PC RUBBER BUSHINGS AND METAL COLLARS 3 PC HARDWARE PACKETS
More informationPart Number SP BMW 335i BMW135i 3.0L Twin Turbo L6
This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. Part Number SP1125 2007-09 BMW 335i 2008-09 BMW 3.0L Twin Turbo L6 1-2 piece air intake system
More informationOwner smanual. Banks Split-Dual Monster Exhaust System Chevy/GMC 6.6L LMM Duramax Turbo-Diesel Pickups. with Installation Instructions
with Installation Instructions Owner smanual Banks Split-Dual Monster Exhaust System 2007-2010 Chevy/GMC 6.6L LMM Duramax Turbo-Diesel Pickups THIS MANUAL IS FOR USE WITH SYSTEM 47785 General Installation
More information