Please check our application list to see if we have a specific Harness Kit available for your motorcycle.
|
|
- Lillian Alexander
- 5 years ago
- Views:
Transcription
1 GIpro X-type Install Guide for GPX-WSS Harness Kit Compatibility: This universal harness kit includes a Wheel Speed Sensor and will fit all motorcycles and vehicles which have electronic ignition system. Please check our application list to see if we have a specific Harness Kit available for your motorcycle. 1. Overview You need to mount the supplied wheel speed sensor and connect 3 wires to the bike s wiring harness. Good quality quick connectors are supplied (3 pcs wire taps). No need to cut any wires and no need for soldering. A universal mounting bracket for the sensor is included. If it s not suitable for your bike, the bracket can be made from a metal piece (about 2mm thick steel is recommended). Due to the large number of bike models and vehicles compatible with this Kit, model specific wire colors and install instructions are not described in this document. To complete the install, it is recommended that you consult with your dealer and/or refer to the Service Manual available for your bike. 2. Installation Disclaimer: Do not attempt to install the product if you don t have basic mechanical and electrical skills. HealTech Electronics Ltd. and its distributors shall not be liable for any loss or damage caused by improper installation. If in doubt, please consult with your dealer. 1. The ignition key should be in OFF position. Remove the seat, raise and support the fuel tank. 2. Connect the GIpro Black wire to a Ground lead near the instrument cluster, e.g. to the ground lead of the parking light or dashboard light. Use the Red wire tap connector supplied. Usage: Place the unstripped run wire (ground lead) inside the run channel. Close the side cover until latched. Cut off the excess length, then insert the unstripped tap wire (Black) completely and check its position. Insert the blade (u-contact) and press down by finger pressure. Then, fully depress the u-contact with pliers. Close the hinged top cover until latched. Alternatively, connect the GIpro Black wire to chassis ground. GPX_WSS_InstallGuide_en.pdf [rev. 002]
2 3. Connect the GIpro Red wire to a switched +12V power lead, such as the hot wire of the parking light or dashboard light. Use the Red wire tap connector supplied. 4. Connect the 4-pole GIpro harness connector to the GIpro display connector. 5. Check whether the Power and Ground connections are correct: Test #1: Turn ignition On The GIpro display should count from 6 to 1, then L flashes slowly. (If not, the display is not receiving power and/or ground.) Turn ignition OFF. 6. Mount the wheel speed sensor so that it will read the bolt heads of the rear brake disc or the bolt heads of the rear wheel sprocket. If rear wheel mount is not possible, you can also install the sensor at the front wheel. Any rotating metal targets will work, but the targets (e.g. bolt heads) must be spaced at equal distances. See mounting examples at the back of this page. Adjust and tighten the sensor so that the tip of the sensor will be in-line with the center of the bolt head. The air-gap should be about 1mm. 7. Connect the 3-pole sensor connector to the GPX wiring harness connector. Test #2: Turn ignition On, then Rotate the wheel at least 5 km/h (3 mph) The GIpro display should indicate a rolling wheel. (If not, the display is not receiving the speed signal. Check the connector pins and adjust the sensor distance. Rotate the sensor body by 45 degrees.) 8. Connect the GIpro Black/Green wire to any of the following options, using the Red wire tap connector supplied: a) The signal wire of the crankshaft sensor (also called Pickup coil or Ignition Pulse Generator). The Crankshaft sensor is inside the crankcase, usually near the Alternator. It has two wires. b) The tacho signal (rpm counter) wire, anywhere between the dashboard connector and the ECU box. c) The ignition coil signal wire, anywhere between the ignition control unit and the coil input terminal. Test #3: Start the engine L should flash faster for a few seconds. (If not, the display is not receiving the RPM signal.) 9. Peel off the green plastic from the back of the unit, and mount the display. 10. Neatly route the cables preferably along the frame. Use the supplied cable ties. Do not bend the harness near the 4-pole connectors. Do not route the harness very close to the exhaust pipe or cylinder head. Make sure the sensor cable is secured properly and kept away from moving parts. 11. Use black tape to secure and isolate the 4-pole connectors. 12. If all tests work fine, refer to the User s Guide for setup instructions. - 2
3 Sensor mounting examples at rear brake calliper bolt using supplied bracket at front axle pinch bolt at the bottom of swingarm, brake disc side at the top of swingarm, sprocket side
4 GIpro X-type Gear Position Indicator with programmable Shift Light and High Speed Warning User s Guide 1. Foreword Congratulations on your purchase of a GIpro X-type gear position indicator. The GIpro products from HealTech Electronics Ltd. are the most advanced gear position indicators on the market today. This GIpro model will fit all motorcycles and vehicles which have an electronic speedometer (either analogue or digital readout). Your speedometer is electronic if the odo/tripmeter has LCD readout. If your speedometer is cable driven, it is still possible to install this product with our GPX-WSS harness kit. Due to a modern microprocessor and sophisticated firmware, the GIpro-X offers faster and more reliable readings than competing products. The unit is also the smallest, most compact gear indicator available, making it easy to mount at the instrument cluster. The display is auto-learning, there are no buttons and no programming wire. 2. Operation Your motorcycle is not equipped with a Gear Position Sensor, therefore determining and displaying the gear in use is only possible when the engine is running and the clutch is fully released. At other times (clutch pulled-in, engine not running, bike stopped) the display will show a - sign. The GIpro will NOT show an incorrect gear in any circumstances, except for a split second when the clutch is released slowly (slipping) during a back shift. 3. Installation The Harness Kit required for the installation is supplied separately. Along with the Display unit, please make sure to order the correct wiring harness kit for your bike. Please refer to the install instructions received with the Harness Kit. GPX_UsersGuide_en.pdf [rev. 002]
5 4. Setup You need to set up this module after installation. It is recommended to perform the setup procedure with WARM engine. - Raise the rear wheel off the ground by using a stand. (If you do not have a stand, or your speedometer is driven off the front wheel, set up the unit while riding. Find a long, straight road with light traffic. The unit does not learn the same gear twice, this makes it easy to set up on the road. You can even shift down and stop during the setup if needed. Do not stare at the display, watch the road and ride with extreme care as always!) - Turn the ignition On. The display counts backwards ( 6 to 1 ) indicating that the memory is clear. (If the display counts upwards when ignition is turned on, the memory is not clear. Perform the Reset procedure if you wish to set it up again.) - The display flashes L (Learning) slowly. Start the engine in Neutral, and let it idle. The display flashes faster for a few seconds while the RPM signal is being received correctly. - The display flashes 1 slowly. At this point, wait until the RPM drops to the normal idle speed. Select 1st gear, release the clutch and keep the engine at approx. 2-4 times of your idle speed (usually RPM). The display flashes faster while the SPEED signal is being received correctly. The unit is now learning the gear position. Depending on the bike model, the learning may take from a few seconds up to a minute. - The display shows n (next) for a second, then 2 flashes slowly. Select 2nd gear, release the clutch and raise RPM. Again, the display flashes faster while learning the gear position. Repeat this process until all gears have been programmed (5 or 6). - In top gear, wait until o (over) is indicated and the display stops flashing. (If your bike has 6 gears, you will need to select 6th gear when prompted, otherwise the unit will exit from programming mode in 5 seconds and you will need to repeat the setup procedure.) The unit is now programmed and should indicate all gears correctly. Now, when ignition is turned on, the display counts forward ( 1 to 5 or 1 to 6 ) indicating that it is programmed and fully functional. Note 1: If you have a SpeedoHealer (or other speedometer calibrator) and you change the calibration factor, probably you will have to reset the GIpro and perform the setup procedure again. Note 2: The unit stores all settings in Flash memory, there is no need to set it up again if you disconnect or remove the battery
6 5. Reset If some gears are not indicated correctly, reset the unit and set it up again. - Have the engine stop switch in OFF position. - Turn the ignition key ON and immediately turn it off while the GIpro display is counting up and is showing 3, 4 or 5. Repeat this step 5 more times. - On the next power up, the display will count backwards ( 6 to 1 ). The memory is now cleared and you can perform the Setup procedure. Note: If you perform the Reset procedure, it will set the device to factory default condition. The Shift Light and High Speed Warning features will also be cleared. 6. Shift Light If you wish, you can program the device to indicate when the desired RPM is reached. The unit will rapidly flash a U (Up) once you exceed the pre-set RPM. The feature is intelligent, as it does not operate in top gear. To activate the feature: - First, perform the deactivation steps as per chapter 8. - When C (Clear) is flashing, raise the RPM very slowly. - The display will begin flashing a U sign, indicating that the Shift Light learning is in progress. The unit learns the highest RPM. - Raise the RPM gradually and very slowly to the desired RPM, and hold it for a second. Release the throttle. - When done, you can save the setting and exit from the learning mode in three ways: start riding, stop the engine or turn ignition off. 7. High Speed Warning If you wish, you can program the device to warn you when your speed exceeds a set limit. The unit flashes the actual gear 1 to 5/6 above the pre-set speed limit. This way you can still see the gear position. To activate the feature: - First, perform the deactivation steps as per chapter 8. - When C (Clear) is flashing, select first gear and start riding. - The display will be flashing an H sign, indicating that the HSW learning is in progress. The unit learns the highest SPEED. - 3
7 - Select a high gear and raise your speed gradually and slowly to the desired speed. Hold it for a second, then slow down and stop. (You should of course slow down and stop as traffic conditions dictate. The unit will not exit from learning mode until you stop the engine. It records the highest speed as long as H is flashing on the display.) - When done, you can save the setting and exit from learning mode two ways: stop the engine or turn ignition off. 8. Deactivating the SL and HSW features If you wish to deactivate or re-program the Shift Light or High Speed Warning features, perform the following steps: - Park the bike and turn ignition On (if it is already on, cycle the ignition key). - Start the engine in neutral, and warm the engine if necessary. (Do not move the bike, otherwise you will need to restart the sequence.) - Gradually and very slowly increase the RPM, and keep it in the range 3-4 times of your idle speed (usually RPM). As a guide, the display will show a (top horizontal bar) sign when you keep the RPM in this range. - Hold the RPM for about 5 seconds, until C (Clear) is flashing on the display. - Now, if you wish to deactivate both features, stop the engine or turn the ignition Off. Otherwise, continue with chapter 6 or 7. Note: you can not activate and use both features at the same time. If you program one, it will clear the previous setting. 9. Warranty The unit is completely sealed and epoxy-encapsulated, which gives the maximum protection for the internal parts from shock, vibration and water ingress. To ensure trouble-free operation from the start, all units have been extensively tested prior to shipment. Our dealers offer a 30-day money-back guarantee on HealTech products if the product does not fulfil your expectations. (All parts must be returned in original condition for full refund.) Furthermore the product is covered by our 2-year replacement warranty from the date of purchase. Web: support@healtech-electronics.com - 4 -
AP500 FAULT FINDING NEW INSTALLATION
AP500 FAULT FINDING NEW INSTALLATION This Bulletin covers the AP500 model which is identified by a black plastic Electronic Module with a silver printed label. This module would normally be mounted behind
More informationINSTALLATION MANUAL AP60B INSTALLATION MANUAL
INSTALLATION MANUAL 2. TOOLS REQUIRED The following is a list of tools required to properly install the cruise control. While this unit may be installed without some of the tools listed, it is recommended
More informationINSTALLATION GUIDE Ford Mustang Digital Dash Panel Part Number: DP7009 Year Series:
Made in America Lifetime Guarantee Thank you for purchasing this gauge panel from Intellitronix. We value our customers! INSTALLATION GUIDE Ford Mustang Digital Dash Panel Part Number: DP7009 Year Series:
More informationPart Number DP6003 Chevy Truck Digital Dash YEARS 67-72
Part Number DP6003 Chevy Truck Digital Dash YEARS 67-72 KIT COMPONENTS: One (1) Digital Circuit Board One (1) Smoked Acrylic See-Through Lens *Peel off protective covering from both sides of lens attached
More informationCANBUS Emulator Mini V1.x. Overview - Installation and Operating Instructions
CANBUS Emulator Mini V1.x Overview - Installation and Operating Instructions Contents Overview... 2 Installation... 3 Basic Install... 3 With optional speed sensor input and reverse signal input... 3 Operation...
More informationCRUISE CONTROL SPEED LIMITER Rev. 4.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series 231.0004530 Rev. 4.0 1 2 CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics module location... 5 4 Input
More informationINSTALLATION GUIDE Six Gauge Universal Digital Dash Panel Part Number: DP10002
Made in America Lifetime Guarantee Thank you for purchasing this digital dash panel from Intellitronix. We value our customers! INSTALLATION GUIDE Six Gauge Universal Digital Dash Panel Part Number: DP10002
More informationINSTALLATION GUIDE Multi-Gauge Set with sending units Part Number: M 9999
Made in America Lifetime Guarantee Thank you for purchasing this instrument set from Intellitronix. We value our customers! INSTALLATION GUIDE Multi-Gauge Set with sending units Part Number: M 9999 * Always
More informationCRUISE CONTROL SPEED LIMITER. SL900Series. Dealer address details: C Rev. 7.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series Dealer address details: 35 231.000453C Rev. 7.0 1 2 NOTES: CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics
More informationINSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6002 Year Series:
Made in America Lifetime Guarantee Thank you for purchasing this instrument panel from Intellitronix. We value our customers! INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6002 Year Series:
More informationINSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6002 YEAR SERIES:
Intelligent Electronics INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6002 YEAR SERIES: 1964-1966 * Disconnect the battery before attempting any electrical work on your vehicle. * KIT
More informationINSTALLATION GUIDE Chevrolet Monte Carlo Dash Panel Part Number: DP9002 Year Series:
Made in America Lifetime Guarantee Thank you for purchasing this instrument from Intellitronix. We value our customers! INSTALLATION GUIDE Chevrolet Monte Carlo Dash Panel Part Number: DP9002 Year Series:
More informationINSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6003 Year Series:
INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6003 Year Series: 1967-1972 * Disconnect the battery before attempting any electrical work on your vehicle. * KIT COMPONENTS One (1) Digital
More informationINSTALLATION GUIDE Chevrolet Impala/Caprice Digital Dash Panel Part Number: DP1208 Year Series: 1968
Made in America Lifetime Guarantee Thank you for purchasing this instrument from Intellitronix. We value our customers! INSTALLATION GUIDE Chevrolet Impala/Caprice Digital Dash Panel Part Number: DP1208
More informationMODEL MVX-2011 TANK MOUNT SPEEDOMETER/TACHOMETER
MODEL MVX-2011 TANK MOUNT SPEEDOMETER/TACHOMETER Wiring Diagram The MVX-2011 gauges will work on 2011-up Softail models with 5 gauges or 2012-up Dyna models with 5 gauges. It is a direct plug in on these
More informationNemesis-TCS system manual release /11/2011 Author Mick Boasman. UK Tel
Nemesis-TCS Traction Control System Firmware TCS 2 cylinder 1.21 onwards Firmware TCS 4 cylinder 1.08 onwards TC-Pod 1.05 WinTC Software 1.11 -User Onwards 2 cylinder WinTC Software 2.04 -User Onwards
More informationMODEL MCL-3212 SPEEDOMETER/TACHOMETER for 2012 up Dyna and Softail with 4 gauge
MODEL MCL-3212 SPEEDOMETER/TACHOMETER for 2012 up Dyna and Softail with 4 gauge IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles (160km) of
More informationUSER MANUAL AND INSTALLATION GUIDE ENGINE RPM AND NOS SHIFT COUNTER NOS DELAY TIME IN SECONDS NOS START PERCENT NOS FINAL PERCENT
SCHNITZ MOTORSPORTS DSC-9PS "PRO-STREET" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE SHIFT LIGHT POSITIVE PAGE 2 SHIFT LIGHT GROUND PAGE 2 NOS SOLENOID GROUND 1GA ORANGE, FUEL SOLENOID GROUND
More informationThank you for purchasing this instrument from Intellitronix. We value our customers!
Made in America Lifetime Guarantee Thank you for purchasing this instrument from Intellitronix. We value our customers! INSTALLATION GUIDE Corvette Digital Dash Panel Part Number: DP2003 Year Series: 1984-1989
More informationINSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6004 Year Series:
INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6004 Year Series: 1973-1987 * Disconnect the battery before attempting any electrical work on your vehicle. * KIT COMPONENTS Three (3) Digital
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationDIGITAL GEAR INDICATOR
DIGITAL GEAR INDICATOR USER GUIDE AND INSTRUCTIONS JULY 2016 CONTENTS INTRODUCTION PAGE 1 INSTALLATION PAGE 2 ENTER MODE PAGE 3 SHIFT LIGHTS - SET LOWER RPM PAGE 4 SHIFT LIGHTS - SET HIGHER RPM PAGE 5
More informationCruise Control designed. The only. and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS. PROFESSIONAL SERIES and DRIVE by WIRE
The only Cruise Control designed and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS PROFESSIONAL SERIES and DRIVE by WIRE CONGRATULATIONS! You have purchased one of the most advanced cruise
More informationAir Shift Module User Manual
1 Air Shift Module User Manual Important leave the shift solenoid connector unplugged until you have configured the shift input polarity and verified correct operation! tech@schnitzracing.com 2 These instructions
More informationMODEL MCL /8 SPEEDOMETER/TACHOMETER for 2004 up
MODEL MCL-3204 3-3/8 SPEEDOMETER/TACHOMETER for 2004 up IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles (160km) of operation. See Odometer
More informationTIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT
Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT TIP SHEET T0937 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself installers
More informationUniversal Wireless Dashboard Y-Dash + Android App Y-Dash GT. User Manual Firmware version 1.6 Software version 2.28 Hardware version 1.
Universal Wireless Dashboard + Android App GT User Manual Firmware version 1.6 Software version 2.28 Hardware version 1.3 Page 2 is an electronic microprocessor based device that collects analog and digital
More informationHLY-3016 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO (weather and vibration resistant for exposed environments)
HLY-3016 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO (weather and vibration resistant for exposed environments) *To avoid damage to motorcycle, please see Speedometer, Tachometer, and Status and Warning Indicators
More informationSPA MICROPROCESSOR COMBINED TACHO&SPEEDO/GAUGE INSTALLATION AND OPERATING MANUAL PAGE 2...INSTRUMENT FEATURES PAGE 3...OPERATING INSTRUCTIONS
SPA MICROPROCESSOR COMBINED TACHO&SPEEDO/GAUGE INSTALLATION AND OPERATING MANUAL PAGE 2...INSTRUMENT FEATURES PAGE 3...OPERATING INSTRUCTIONS PAGE 3...MENU SYSTEM PAGE 9...INSTALLATION DIAGRAMS PAGE 13...INSTALLATION
More informationDMR Series User Guide
1 INTRODUCTION DMR Series User Guide This manual provides instructions on incorporating your Castle Creations DMR (Dedicated Multi-Rotor) ESCs into your aircraft, from wiring and mounting your ESCs to
More informationChevy Truck
Classic Instruments 1967 1972 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Remove the Stock / OEM Instrument Panel... 4 Instrument Cluster Wiring...
More informationWWW.MORETRACTION.COM TMS-5500-SL ELECTRONIC TRACTION CONTROL US PATENT 6,577,944 Other Patents Pending COPYRIGHT NOTICE Copyright 1999-2013 Davis Technologies, LLC. All rights reserved. Information in
More informationREMOVAL OF FACTORY GAUGE ULTRA FLHT & FLHX (STREET GLIDE
MCL-36K-SPD Thank you for purchasing the Dakota Digital MCL-36K-SPD gauge for your Harley Davidson Touring bike. This kit is designed to be a direct, plug in replacement for all touring models from 2004
More informationClassic Instruments. Belera. Installation Manual
Classic Instruments Belera Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Optional Gear Indicator Mounting... 4 Gauge Mounting... 6 Gauge Cluster Wiring... 8 Gauge
More informationIndian Speedometer and Body Control Module Service Tool Users Guide
Indian Speedometer and Body Control Module Service Tool Users Guide Installing speedometer software to your computer 1. Go to the Indian Motorcycle Website: WWW. Indianmotorcycle.com 2. Log in to Service
More informationFord Mustang. Installation Manual
1965 1966 Ford Mustang Installation Manual TABLE OF CONTENTS Welcome from the Team at Classic Instruments! 3 Mounting Gauges in New Bezel 4 3 3/8 Speedometer Wiring 6 3 3/8 Speedometer Wiring Diagram 6
More informationClassic Instruments Cluster. Installation Manual
Classic Instruments 6400 Cluster Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Speedometer & Tachometer
More informationMustang. Installation Manual
1967-1968 Mustang Installation Manual Table of Contents WELCOME FROM THE TEAM AT CLASSIC INSTRUMENTS!... 3 REMOVE THE ORIGINAL INSTRUMENT PANEL... 4 WIRING DIAGRAM... 6 WIRING THE NEW INSTRUMENT CLUSTER...
More informationIdle Timer Controller - ITC Freightliner MT45 Contact InterMotive for additional vehicle applications
An ISO 9001:2008 Registered Company System Operation Idle Timer Controller - ITC805 2013-2018 Freightliner MT45 Contact InterMotive for additional vehicle applications The ITC805 system shuts down idling
More informationTIP SHEET. Installation Tips for your RS IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14. 1 P a g e
Installation Tips for your RS-150 + IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14 TIP SHEET Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts
More informationNemesis-TCS Traction Control System Installation manual Honda CBR600 RR 2003_04 with race seat
Nemesis-TCS Traction Control System Installation manual Honda CBR600 RR 2003_04 with race seat Kit part No. TCS-4C_CBR600_RR_0304.AA This application is designed for use with the Honda CBR600 RR 2003_2004
More informationQuick-Kill Installation Manual V1.0 (Universal Motorcycle Application)
Quick-Kill Installation Manual V1.0 (Universal Motorcycle Application) THIS INSTALLATION MANUAL IS FOR UNIVERSAL FUEL INJECTED MOTORCYCLE APPLICATIONS (NON PLUG AND PLAY), WITH OR WITHOUT A GEAR POSITION
More informationSECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake
SECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch.............................................. 114 Automatic transmission.....................................
More informationMCL-3014 gauge kit. Optional Readings: Boost Pressure with MBM-09, Front or Rear Air Suspension Pressure with MBM-19
MCL-3014 gauge kit Thank you for purchasing the Dakota Digital MCL gauge kit for your Harley Davidson Touring bike. This kit is designed to be a direct plug in replacement for all touring models from 2014
More informationThe GearMaster II. Making Shifting a Breeze
The GearMaster II Making Shifting a Breeze Congratulations on your purchase of the GearMaster, the world s first and only Gear Availability and Synchronization Indicator! You will find that the GearMaster
More informationTIP SHEET T0937. Installation Tips for RS00 + Passlock-sl2(4) + SPDT
Installation Tips for RS00 + Passlock-sl2(4) + SPDT TIP SHEET T0937 Chevrolet (Astro 1998-2005) (Avalanche 2002-2006) (Blazer 1998-2005) (Express Van 1998-2007) (Impala 2000-2005) (Monte Carlo 2000-2005)
More informationMaximiser Progressive Controller
Maximiser Progressive Controller Street & Race Model Owner's Manual 44 (0) 01302 834343 www.noswizard.com Introduction Congratulations on purchasing the Maximiser for the ultimate in progressive nitrous
More informationClassic Instruments Chevelle. Installation Manual
Classic Instruments 1964 1965 Chevelle Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Included Mounting Hardware... 4 Mounting Gauges... 5 Wiring Diagram... 6
More informationION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO
ION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO MOUNTING: It should be inserted into the opening from the front and the L-clamps will be installed from the back. Tighten the nuts on the L-clamps so that
More informationELECTRONIC TRACTION CONTROL USER MANUAL
DRAG-SPORTSMAN N2O For ELECTRONIC TRACTION CONTROL USER MANUAL TELEPHONE 828.645.1505 FAX 828.645.1525 WWW.MORETRACTION.COM US PATENT 6,577,944 Disclaimer...2 Introduction... 3 How Does It Work. 4 Installation...
More informationInstallation & Calibration
Installation & Calibration ED2-AT Series SkidWeigh System Lift Truck On-board Check Weighing With Accumulative Load Weight Total ED2-AT Series SkidWeigh V.1.1 General Installation Guide This ED2-AT Series
More informationTri-Spark Ignition System Installation Triple Cylinder TRI-0001
Tri-Spark Ignition System Installation Triple Cylinder TRI-0001 There are potentially lethal high voltages produced at the ignition coils and spark plugs, therefore every precaution must be taken to prevent
More informationClassic Instruments Ford F100. Installation Manual
Classic Instruments 1953 1955 Ford F100 Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Speedometer
More informationToyota Landcruiser Xtreme 2014 V8 5.7 Uses DbWRS 09CC
Toyota Landcruiser Xtreme 2014 V8 5.7 Uses DbWRS 09CC Wiring Description Fitting Instructions Tools Required Calibration The Drive by Wire kit supplied by Autokontrol must only be fitted by accredited
More informationINSTALLATION INSTRUCTIONS. Applications: 2005-Current Ford Excursion 2005-Current Ford F250, F-350, F-450 & F-550 Super Duty Pickups.
30453 INSTALLATION INSTRUCTIONS Tools Required: Drill with 1/8 Bit 1/4 Nut Driver Phillips Screwdriver Probe Style Test Light Applications: 2005-Current Ford Excursion 2005-Current Ford F250, F-350, F-450
More informationNEXTUP TERMINAL STRIP CONTROLLER INSTALLATION MANUAL - VER 1.5
CONTENTS INTRODUCTION 1 STEP ONE QUICKSHIFTER Power and Ground 3 STEP TWO QUICKSHIFTER Wiring and Final Connections 4 STEP ONE AIR SHIFTER Power and Ground 6 STEP TWO AIR SHIFTER Wiring and Final Connections
More informationCHERY P Wiring Description Fitting Instructions Tools Required Calibration
CHERY P5 2014 Wiring Description Fitting Instructions Tools Required Calibration The Drive by Wire kit supplied by Autokontrol must only be fitted by accredited installer as certified by Autokontrol Limited.
More informationTach-Force Chevy Truck
Classic Instruments Tach-Force 1955 1959 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5
More informationMCL-30K-TCH. Remove nuts/screws and clamp to remove factory gauges 1 MAN#650336
MCL-30K-TCH Thank you for purchasing the Dakota Digital MCL-30K-TCH gauge for your Harley Davidson Touring bike. This kit is designed to be a replacement for all touring models, from 1996 2003. This is
More informationPage 1. File: Motolight caliper one-piece Date: 8/14/2006
Page 1 Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE READ ALL THE INSTRUCTIONS.
More informationClassic Instruments. Ultimate Speedometer & Speed-Tachular. Installation Manual
Classic Instruments Ultimate Speedometer & Speed-Tachular Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Gauge Wiring... 4 Ultimate Speedometer Wiring Diagram...
More informationClassic Instruments. Six Pack. Installation Manual
Classic Instruments Six Pack Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Universal, Shoebox & 61-66 F100 Gauge Mounting... 4 Bronc Package Gauge Mounting...
More informationChevy Truck
Classic Instruments 1973 1987 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Gauge Mounting... 4 Gauge Cluster Wiring... 6 Pulse Signal Generator [SN16]
More informationWOT Box Installation Instructions VW / Audi
Connector Pinout Pin Color AWG Name WOT Box Installation Instructions VW / Audi Description 1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model) 2 Black
More informationSCHNITZ MOTORSPORTS USER MANUAL AND INSTALLATION GUIDE PRO-MOD BATTERY VOLTS DIAGNOSTICS NOS PULSE FREQUENCY NOS DELAY TIME IN SECONDS
SCHNITZ MOTORSPORTS DSC-CS "PRO-MOD" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, COIL, NEGATIVE GA WHITE, GA BLACK, SHIFT LIGHT +V OUTPUT PAGE 0 NOS ACTIVATION INPUT
More informationFuller Automated Transmissions TRDR2500
Driver Instructions Fuller Automated Transmissions TRDR2500 July 2007 RTO-10910B-DM2 RTO-12910B-DM2 RTO-14910B-DM2 RTO-16910B-DM2 Warnings & Cautions Warnings & Cautions WARNING Read the entire driver
More informationMODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER
MODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER *To avoid damage to motorcycle, please see Speedometer, Tachometer, and Status and Warning Indicators sections for details on locating VSS, Tachometer,
More informationFuller Automated Transmissions TRDR0082
Driver Instructions Video Instruction Available Instructional videos are available for download at no charge at roadranger.com Videos are also available for purchase. To order, call 1-888-386-4636. Ask
More informationAn Actual Driving Lesson Learning to drive an automatic car
An Actual Driving Lesson Learning to drive an automatic car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without
More information6 Gauge Box Set IS0333
Caution 6 Gauge Box Set IS0 Rev. B ecr 882 9/202 Disconnect the battery during installation. Tighten nuts on the back clamp only slightly more than you can tighten with your fingers. Six inch-pounds of
More informationAUTOMATIC AND MANUAL TRANSMISSION MODELS* *MUST USE M SERIES REMOTE STARTER!
REV.2011.7.22 80 SERIES Advanced Remote Starters & Vehicle Security Systems AUTOMATIC AND MANUAL TRANSMISSION MODELS* *MUST USE M SERIES REMOTE STARTER! WARING: NEVER USE AN AUTOMATIC TRANSMISSION STARTER
More informationPart 1 OPERATION OF INSTRUMENTS AND CONTROLS
Part 1 OPERATION OF INSTRUMENTS AND CONTROLS Chapter 1-6 Ignition switch, Transmission and Parking brake Ignition switch with steering lock Automatic transmission Manual transmission Four-wheel drive system
More informationGear indicator models. GearTronic GT3000. Gear Indicators F.A.Q. & Troubleshooting v1.0 28/03/2017
Gear Indicators 2017 F.A.Q. & Troubleshooting v1.0 28/03/2017 Gear indicator models GearTronic GT3000... 1 GearTronic² GT400... 2 GearTronic ZERO GT3100-D1, GT3100-D4, GT3100-D5...3 GearTronic ZERO GT310-D2...
More informationClassic Instruments Ford. Installation Manual
Classic Instruments 1940 Ford Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mount New Gauge Cluster... 4 Instrument Cluster Wiring... 5 Pulse Signal Generator
More informationInstallation Tips for RS4/RS7 + EVO-ALL (NIS 3.c) + 2 diodes
Installation Tips for RS4/RS7 + EVO-ALL (NIS 3.c) + 2 diodes TIP SHEET T3093 + T3103 FOR: NISSAN ( 09-14 Cube), ( 11-14 Juke), & ( 07-11 Versa) automatic, regular key vehicles Thank you for purchasing
More informationPart Number: Code: CL7
Document # 16.01.00 PIO/DIO Rev. A 06/23/08 TOYOTA YARIS 2008- ELECTRONIC CRUISE CONTROL KIT Part Number: 00016-52030 Code: CL7 Section I Installation Preparation Kit Contents Item # Qty. Description 1.
More information1. Cotter pin 2. AXIP nut
below with care: a. Make sure there is an enough gap between the disc pads. b. Make sure the projecting portion (torque stopper) of the speedometer housing is positioned correctly. 1. Cotter pin 2. AXIP
More informationCYCLE COMPUTER OWNER'S MANUAL ENGLISH FRANÇAIS ESPANOL DEUTSCH ITALIANO
CYCLE COMPUTER OWNER'S MANUAL ENGLISH FRANÇAIS ESPANOL DEUTSCH ITALIANO INTRODUCTION Congratulations on your purchase of the new Vetta C-06 cycle computer. The C-06 is designed to be the simplest, smallest
More informationMCL-30K-SPD IMPORTANT NOTE!
MCL-30K-SPD Thank you for purchasing the Dakota Digital MCL-30K-SPD gauge for your Harley Davidson Touring bike. This is designed to be a replacement for all touring models from 1996 2003. This is part
More informationQUICK INSTALLATION GUIDE
MANUAL/AUTOMATIC T R A N S M I S S I O N 2 - B U T T O N R E M O T E S T A R T E R W I T H V I R T U A L T A C H S Y S T E M ( A S P R G - 1 0 0 0 C O M P A T I B L E ) QUICK INSTALLATION GUIDE Manual
More informationClassic Instruments Chevy. Installation Manual
Classic Instruments 1957 Chevy Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 Speedo, Tach, Volt and Oil Pressure Gauge Wiring... 5 Speedo,
More informationAURORA SERIES GAUGES FUEL GAUGE SUGGESTED TOOLS AND MATERIALS. 3 3 /8 in (85.7 mm) PARTS LIST
GAUGE INSTALLATION. Select mounting locations for the fuel gauge. 2. Cut a 2 /6 (52 mm) diameter hole for the gauge and test for proper fitmate. 3. Tighten the gauge with the enclosed Aurora Mounting Clamp
More informationCONTROL BOX. Wiring the control box into the vehicle. +12V
CONTROL BOX Once the display panel is in place, mount the control box within the connecting cable's distance (approximately 3 feet) and secure to the underside of the dashboard. This case does not have
More informationPage 1 of 29 Section 04-05: Suspension, Computer Controlled 1997 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/16/2000 Suspension, Computer Controlled Inspection and Verification
More informationPLATINUM PRO PLUG-IN HONDA CIVIC (EP3)
PLATINUM PRO PLUG-IN HONDA CIVIC (EP3) 2002-2005 (HT055047) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com
More informationOverview of operation modes
Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual, automatic and mappable modes 1 to 4. The MapDCCD
More informationPLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980) Version 4
PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH:
More informationHigh Idle Kit Dodge Cummins (24 valve) Dodge Cummins (with APPS on motor) PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
U 6 May 2014 (1036620-27) 1998.5-2014 Dodge / GMC High Idle Kit (I-00321) 1 High Idle Kit 1036620 1998.5 2002 Dodge Cummins (24 valve) 2003-2004 Dodge Cummins (with APPS on motor) 1036621 2005-2006 Dodge
More informationOMEM200 Tuning Manual 3v Series ECU. Tuning Manual OMEM200.
200 Series ECU Tuning Manual OMEM200 www.omextechnology.com 0 1 Introduction... 3 1.1 What this manual covers... 3 1.2 Notation Used in This Manual... 3 2 Software... 4 3 Sensor Setup... 5 3.1 Throttle
More informationInnovative Racing Electronics
MPS Fast FI Mixture Control Installation Instructions The MPS Fast FI Mixture Control P/N 1-0337 is a simple means to adjust the fuel curves on your fuel-injected motorcycle. This allows for tuning after
More informationMustang. Installation Manual
1967-1968 Mustang Installation Manual I Table of Contents TABLE OF CONTENTS... II WELCOME TO THE TEAM OF CLASSIC INSTRUMENTS!... III REMOVE ORIGINAL INSTRUMENT PANEL... 1 DETERMINE SPEEDOMETER SIGNAL...
More informationRSR Twin Cam Bonneville Gear Indicator
RSR Twin Cam Bonneville Gear Indicator First step is to mount the gauge where you can easily see it in normal vehicle operation. A gear position indicator is meant to be used, not just because it is a
More informationFM SECURITY AND REMOTE START SYSTEM
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with
More informationGear Indicator FZ1 Installation
Overview This Gear-Indicator is designed to work with a Yamaha FZ1N/Fazer motorbike ( 06 onwards). The module is mounted to the lower edge of the dashboard. The Gear-Indicator utilizes the signals of speedo,
More informationPHOENIX Features of the Phoenix-25 : 2.3 Connecting the Motor. 2.4 Reversing Rotation. 2.5 Connecting the Receiver
Warning! High power motor systems can be very dangerous! High currents can heat wires and batteries, causing fires and burning skin. Follow the wiring directions carefully! Model aircraft equipped with
More informationChevy Truck
Classic Instruments 1947 1953 Chevy Truck Installation Manual Table of Contents Welcome from the Team at Classic Instruments!... 3 Mounting Gauges... 4 4 5/8 Speedometer Wiring [no included tachometer]...
More informationSwitch select of sender types:
Full sweep minor gauges wiring: B -------------------------------------------------- battery or +12V input. L -------------------------------------------------- LED illumination, for back lighting, dimmable.
More informationPLATINUM SPORT GM (HT051100) QUICK START GUIDE. Version
PLATINUM SPORT GM (HT051100) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for
More informationSeries II ODYR/SLX-01-1-C PERFORMANCE SPEEDOMETER
Series II ODYR/SLX-01-1-C PERFORMANCE SPEEDOMETER MOUNTING: The gauge requires a round hole 3-3/8 in diameter. It should be inserted into the opening from the front and the U-clamp will be installed from
More informationapril systems design Ltd
april systems design Ltd www.aprilsystems.co.uk Detonation detection system M8 and M6 Stud detector Nov11 Overview Detonation is the pre-ignition of fuel in the cylinder and can cause piston damage; a
More information