Condensed Version of Operator s Manual For The VL600 Series Flowmeters

Size: px
Start display at page:

Download "Condensed Version of Operator s Manual For The VL600 Series Flowmeters"

Transcription

1 Condensed Version of Operator s Manual For The VL600 Series Flowmeters Warranty Agreement JTEC Associates warrants this product to be in good working order for a period of twelve (12) months from installation. This warranty period will not exceed eighteen (18) months from the date of purchase and is valid only if the warranty form is returned validating the date of installation. If the warranty form is not received by JTEC within six months of the date of sale, noting the date of installation, the warranty period will be 12 months from the date of purchase. Introduction The VL600 Series Flowmeters are designed to provide accurate and repeatable liquid flow measurement in designated engineering units. The flowmeters employ a patented ultrasonic technique to measure a form of turbulence created in the flow stream. This turbulence, known as Von Karman Vortex Street, is related to the volumetric flow through the pipe. The flowmeter primary output is a 420 milliampere (ma) current source whose current output is proportional to the flow. The secondary output is a pulse train whose frequency is directly proportional to the flow. Each VL600 Series Flowmeter is precisely calibrated against flow standards traceable to NIST (National Institute of Standards and Technology). The VL600P Series Flowmeters are for pipe diameters 1/2, 1, 11/2, 2, 3 and 4 inches. The VL650 Series Flowmeters are for pipe diameters of 1, 11/2, 2 and 3 inches. The VL600TRI Series Flowmeters are an insertionstyle retractable flowmeter that is installed through a 2inch full port isolation valve which permits the unit to be retracted or inserted manually without shutting down the system. These flowmeters are calibrated in actual volumetric flow rates such as gallons per minute (GPM). Installation/Installation Location The flowmeter has been shipped completely assembled, tested and ready to operate in its permanent location. JTEC recommends a minimum of 20 pipe diameters upstream of any obstruction such as elbows and valves, a minimum of 10 pipe diameters is recommended from the meter itself. For shorter distances, consult factory for change in accuracy and performance. The VL600 Series Flowmeters use a patented ultrasonic technique to measure volumetric flow. An ultrasonic noise can interfere with this technique, therefore, high intensity ultrasonic noise sources should not be located upstream or downstream from the sensor. Common ultrasonic noise sources include the following: 1. Slightly cracked valves operating with large pressure drops. 2. Small pipe leaks in high pressure systems. 3. Flange gaskets must not project into the flow stream. Gaskets should be trimmed approximately 1/8 larger in diameter than the bore of the meter. If these ultrasonic noise sources cannot be eliminated, the meter should be mounted with at least one elbow between the flowmeter and the noise source. The VL600P Series Flowmeters are designed with Schedule 80 tube ends (no fittings). Optional fittings are flanges, male adapters, female adapters, or unions. The labeling of the flow direction on the flowmeter should be aligned with the flow in the pipe. WARNING: Unnecessary overtightening will cause damage to both pipe and fitting. The VL650 Series Flowmeters are designed to mount between two ANSI flanges using the appropriate bolts. The flowmeter should be mounted so its inside diameter is centered inside the pipe. Gaskets (not provided) are necessary between the sensor and the ANSI flanges. Insure that these gaskets are properly installed and do not protrude into the flow stream. The labeling of the flow direction on the flowmeter should be aligned with the flow in the pipe. See Table 5 on Page 2. CAUTION: Avoid bending the vortex strut or damaging the transducers during installation. Do not remove cover plates while unit is operating in the system. The VL600TRI Series Flowmeters are designed to mount on a standard ANSI 150 lb., 2inch pipe flange. It is recommended that the customer conduct a flow profile survey and place the probe at the optimum point. The labeling of the flow direction on the sensor should be aligned with the flow in the pipe. CAUTION: Avoid bending the vortex strut or damaging the transducers during installation. Do not remove cover plates while unit is operating in the system.

2 Upstream Obstruction Minimum Required Straightrun Pipe Diameters Upstream From Meter 90 Elbow 10 Two 90 Elbows, Same Plane 15 Two 90 Elbows, Different Planes 20 Flow Straightener (recommended whenever an axial swirl exists in the 10 flow stream) Fully Open Shutoff Valve 5 Downstream Obstruction Minimum Required Straightrun Pipe Diameters Downstream From Meter Control Valve 5 TABLE 5 Minimum Piping Requirements The VL600TRI Series Flowmeters are designed to mount on a standard ANSI 150 lb., 2inch pipe flange. It is recommended that the customer conduct a flow profile survey and place the probe at the optimum point. The labeling of the flow direction on the sensor should be aligned with the flow in the pipe. CAUTION: Avoid bending the vortex strut or damaging the transducers during installation. Do not remove cover plates while unit is operating in the system. The VL600TRI insertion flowmeter has a torque requirement for the conax fitting which is ft. lbs. Electrical Installation VL600P Series: The electrical connections are made using screw type terminals located inside the electronics enclosure. To expose these terminals, remove the lid from the electronics enclosure. VL650 and VL600TRI Series: Electrical connections are made using screwtype terminals located inside the electronics enclosure. To expose these terminals, remove the lid from the smaller end of the AdaletTM enclosure. Flowmeter Wiring A two or three conductor cable of 12 to 24 AWG solid or stranded wire is required to make a connection to the flowmeter. It is recommended that a shielded interconnecting cable be used. The maximum cable length for the power depends on the supply voltage required to drive the flowmeter and the current meter being used to monitor the current output of the flowmeter. The maximum length of the cable is determined by using Figure G to calculate the maximum load (resistance in Ohms) that can be driven using the known power supply voltage. In determining this value the voltage drop across the meter being used to monitor the current output of the flowmeter must be considered. After this value has been found, Table 6 can be used to calculate the resistance in the cable being used and adjust the input voltage as required. See Figure D Flowmeter Terminal Functions on Page 3 See Figure E Flowmeter Hookup Examples on Page 5 See Figure G Load Resistance vs. Supply Voltage on Page 4 Ohms/Ft Related to Wire Size (AWG) 12 AWG = Ohm/Ft 14 AWG = Ohm/Ft 16 AWG = Ohm/Ft 18 AWG = Ohm/Ft 20 AWG = Ohm/Ft 22 AWG = Ohm/Ft 24 AWG = Ohm/Ft TABLE 6 Line Resistance For Current Lines

3 VL600P SERIES FLOWMETER CHASSIS GROUND SCREW VL650 & VL600TRI SERIES FLOWMETER FIGURE D Flowmeter Terminal Functions

4 Rt MAX (OHMS) Rt MAX = (Vloop12V)/20mA SUPPLY VOLTAGE (32 VDC MAX) FIGURE G Load Resistance vs. Supply Voltage

5 420 ma RECEIVER + VL600P Series Terminal Block Layout 1332 VDC POWER SUPPLY + 2CONDUCTOR SHIELDED CABLE + CURRENT OUTPUT 2WIRE HOOKUP R/T DISPLAY 420 ma RECEIVER + VL600P Series Terminal Block Layout 10 uf Capacitor 1332 VDC POWER SUPPLY + 2CONDUCTOR SHIELDED CABLE + CURRENT OUTPUT 2WIRE HOOKUP WITH RATE/TOTALIZER DISPLAY VL600P Series Terminal Block Layout 420 ma RECEIVER + BATCHER 1332 VDC POWER SUPPLY + 2CONDUCTOR SHIELDED CABLE + CURRENT OUTPUT 2WIRE HOOKUP WITH FREQUENCY OUTPUT FIGURE E VL600P Series Flowmeter Examples of Various Flowmeter Hookups

6 Pulse Output Line The pulse output is a secondary output and is not intended for long transmission. The load on the line must be 50,000 Ohms minimum and 1,000 picofarads maximum. Operation The flowmeter s 3 or 4 position terminal strip provide all the connections needed to operate the flowmeter. +/ 420 ma Terminals The +/ 420 ma terminals are used for the flowmeters power supply. This power supply should be 13 to 32 VDC and be capable of supplying 20 ma to the flowmeter. This output is a standard 4 to 20 ma output, where 4 ma corresponds to no flow and 20 ma indicates 100% (full scale) flow. The correct output will not be accurate if the load resistance on the current output terminal is too high. The maximum load resistance that the terminal can drive versus the power supply voltage is shown in Figure G. Please see Flow Meter Wiring in this manual for further data. Frequency (Freq Out) Terminal If the Frequency (Freq Out) function is to be used the flowmeter must be powered as described in the previous paragraph for this option to be functional. Attach a cable as described in this manual to the Freq Out terminal and terminate the other end of the cable at the desired location. The pulse train output frequency is proportional to the liquid flow. The pulse levels are 0.7 to 6 VDC. See Figure H Troubleshooting Chart Flow Conditions on Page 7 See Figure J Troubleshooting Chart Flow Conditions on Page 8 See Figure R Rescaling of Circuit Card on Page 9

7 START Change Wire Check Wiring at Terminal Strip Wiring Correct? Does Unit have PWR on? Turn on Power Problem Output Current Present? Output Correct? Check PWR Requirements Is PWR Connected to J2 on Ckt Card? Too High? Check for 4 ma Output From CUR to GND Is Freq Output Zero? Is 4 ma Present? PCB Bad.. Done Is Flow Really Zero? Eliminate Flow Adjust HYS (R14) Clockwise Until Freq = Zero Is Freq Really Zero? Check Current Output Is Current 4 ma? Done FIGURE H Troubleshooting Chart Flow Conditions JTEC Associates, Inc. REVISION E

8 START Erratic Output? Unit Installed Correctly? Correct Positioning Adjust Flow for Value In Meter Range Is Flow Too High or Low for Range of Meter? Does Meter Have Valves, Regulator, Elbow or Sonic ises Upstream of Meter? Eliminate ise Source Use Setup Procedure Does Current Output Match Freq Output from Calibration Data Sheet? Does Meter Have Correct Pipe Diameters Upstream Pipe Downstream? or Install More Pipe Does Unit Show Clean Pulse On FREQ Terminal? Unit Showing Actual Flow For Further Assistance FIGURE J Troubleshooting Chart Flow Conditions JTEC Associates, Inc. REVISION E

9 RESCALING THE CURRENT OUTPUT This procedure details the rescaling of the current output after installation. Applicable connections and component locations are described in Figure R. NOTE: Make sure the VL600 Series Flowmeter is filled with liquid prior to performing this rescale function. 1. Connect power (13 to 32 VDC) to terminals marked ma. Return with a device to measure the current output as illustrated in Figure R. 2. Connect a frequency counter to the terminal marked FREQ OUT. 3. Turn on power to the circuit board. While pressing the TEST button, monitor the frequency output. 4. Adjust the potentiometer marked TEST FREQ to the desired frequency for full scale flow. 5. Continue pressing the TEST button and monitor the current output reading. If the current output does not read correctly (20 ma), then adjust the potentiometer FULL SCALE ADJ until 20 ma is achieved. 6. Release the TEST button. 7. If all adjustments have been made successfully, the unit is rescaled. FIGURE R Rescaling of DBA0903 Liquid Flowmeter Circuit Card JTEC Associates, Inc. REVISION E

Condensed Version of Operator s Manual For The VI/VP700 Series Flowmeter and VI800 Series Flowmeter

Condensed Version of Operator s Manual For The VI/VP700 Series Flowmeter and VI800 Series Flowmeter Condensed Version of Operator s Manual For The VI/VP700 Series Flowmeter and VI800 Series Flowmeter Warranty Agreement J-TEC Associates warrants this product to be in good working order for a period of

More information

Model 1000 Vortex Meter

Model 1000 Vortex Meter Model 1000 Vortex Meter Installation and Instruction Manual Table of Contents General Information... 1 1-1 General... 1 1-2 Principles of Operation... 1 1-3 Sensor Operation... 1 1-4 Calibration Factor...

More information

Model 5000 Vortex Meter

Model 5000 Vortex Meter Model 5000 Vortex Meter Installation and Instruction Manual Table of Contents General Information... 1 1-1 General... 1 1-2 Principles of Operation... 1 1-3 Sensor Operation... 1 1-4 Calibration Factor...

More information

Operating Instruction for Plastic Vortex Flow Transmitter. Model: UV

Operating Instruction for Plastic Vortex Flow Transmitter. Model: UV Operating Instruction for Plastic Vortex Transmitter Model: UV DESCRIPTION INTRODUCTION The UV series vortex-shedding flow meter is a general-purpose electronic liquid flow meter. The standard output is

More information

F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide

F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide 11451 Belcher Road South, Largo, FL 33773 USA Tel +1 (727) 447-6140 Fax +1 (727) 442-5699 1054-7 / 34405 www.onicon.com sales@onicon.com

More information

WATER METERS OCTAVE ULTRASONIC WATER METER INSTALLATION & USER GUIDE

WATER METERS OCTAVE ULTRASONIC WATER METER INSTALLATION & USER GUIDE WATER METERS OCTAVE ULTRASONIC WATER METER INSTALLATION & USER GUIDE OCTAVE ULTRASONIC WATER METER INSTALLATION & USER GUIDE TABLE OF CONTENTS General Information...4 Warranty...4 Included Items...4 Operation...5

More information

TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX :2008 ISO CERTIFIED COMPANY TX80-SERIES FLOW SENSOR INSTRUCTIONS

TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX :2008 ISO CERTIFIED COMPANY TX80-SERIES FLOW SENSOR INSTRUCTIONS TX80-SERIES FLOW SENSOR INSTRUCTIONS TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX82 9 001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Specifications, Features...Page 1 Installation

More information

User Manual. Intrinsically Safe Flow Meters. RWG/RWBG Wafer Style Flow Meters RNG Insertion Style Flow Meters. VRX-UM EN-03 (October 2014) Flow

User Manual. Intrinsically Safe Flow Meters. RWG/RWBG Wafer Style Flow Meters RNG Insertion Style Flow Meters. VRX-UM EN-03 (October 2014) Flow Intrinsically Safe Meters RWG/RWBG Wafer Style Meters RNG Insertion Style Meters FLOW VRX-UM-00374-EN-03 () User Manual Intrinsically Safe Meters, RWG/RWBG Wafer Style Meters & RNG Insertion Style Meters

More information

F-2600 SERIES INLINE VORTEX FLOW METER

F-2600 SERIES INLINE VORTEX FLOW METER F-2600 SERIES INLINE VORTEX FLOW METER APPLICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F (260

More information

Hydro-Flow Model 3100 Retractable Insertion Vortex Flowmeter Installation and Operation Manual

Hydro-Flow Model 3100 Retractable Insertion Vortex Flowmeter Installation and Operation Manual Hydro-Flow Model 00 Retractable Insertion Vortex Flowmeter Installation and Operation Manual Table of Contents Model and Suffix Codes. Theory and Identification.. Installation Guidelines Mechanical Drawing:

More information

TR-QS Wafer-Style Turbine Flow Meters Installation, Operating & Maintenance Manual

TR-QS Wafer-Style Turbine Flow Meters Installation, Operating & Maintenance Manual COMPANY TR-QS Wafer-Style Turbine Flow Meters Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:TRQSMAN16 Table of Contents Contents Table of Contents... 2

More information

EX80 Series EX81 EX82. E X 8 0 S E R I E S E l e c t r o m a g n e t i C F l o w s e n s o r i n s t r u c t i o n s. The Leader in Flow Meter Value.

EX80 Series EX81 EX82. E X 8 0 S E R I E S E l e c t r o m a g n e t i C F l o w s e n s o r i n s t r u c t i o n s. The Leader in Flow Meter Value. E X S E R I E S E l e c t r o m a g n e t i C F l o w s e n s o r i n s t r u c t i o n s EX Series Electromagnetic FLOW SENSOR instructions EX EX The Leader in Flow Meter Value. Table of Contents General

More information

Hot Tap Insertion Vortex

Hot Tap Insertion Vortex Hot Tap Insertion Vortex Product Features The same insertion meter can measure Steam, Gases or Liquids. Standardize on an insertion bar that can measure line sizes 2 48 Heavy Duty & Maintenance Free Design

More information

F-2700 SERIES INSERTION VORTEX FLOW METER

F-2700 SERIES INSERTION VORTEX FLOW METER F-2700 SERIES INSERTION VORTEX FLOW METER APPLICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F (260

More information

MODEL 1100 TURBINE FLOW METER

MODEL 1100 TURBINE FLOW METER MODEL 1100 TURBINE FLOW METER INSTALLATION & INSTRUCTION MANUAL 8635 Washington Ave. Racine, Wisconsin 53406 Phone: 800.433.5263 Fax: 800.245.3569 www.hedland.com 2 OPERATIONAL START-UP Fluid entering

More information

F-2700 SERIES INSERTION VORTEX FLOW METER

F-2700 SERIES INSERTION VORTEX FLOW METER F-2700 SERIES INSERTION VORTEX FLOW METER CALIBRATION Every ONICON flow meter is wet calibrated in a flow laboratory against standards that are directly traceable to N.I.S.T. A certificate of calibration

More information

VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Mass Flow Meters. Instruction Manual

VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Mass Flow Meters. Instruction Manual Table of Contents VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Mass Flow Meters Models M22-VT, M22-VTP, M23-VT, M23-VTP Instruction Manual Part Number IM-22-VT, VTP, IM-23-VT,VTP 04/05 8475 W-I25

More information

Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual

Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual COMPANY Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual Mechanical Specifications Flow Meter with Polypropylene Body (ES version) Maximum Operating Pressure: 150 PSIG Maximum

More information

Hydro-Flow Model 3100

Hydro-Flow Model 3100 Hydro-Flow Model 3100 Installation and Operation Guide installation and operation guide Contents: Understanding Your Flow Meter... 1 Identifying Your Flow Meter...2 Installing Your Flow Meter...3,4 Making

More information

ARCHIVED. EX80 Series. (Includes Dates 6/28/05 to 10/06) EX81 EX82

ARCHIVED. EX80 Series. (Includes Dates 6/28/05 to 10/06) EX81 EX82 E X S E R I E S E l e c t r o m a g n e t i C F l o w s e n s o r i n s t r u c t i o n s EX Series Electromagnetic FLOW SENSOR instructions EX EX The Leader in Flow Meter Value. Table of Contents General

More information

Model FVP General Specification. Flanged Vortex Plate. Product Features

Model FVP General Specification. Flanged Vortex Plate. Product Features Flanged Vortex Plate Product Features Our Inline meters can measure Steam, Gases or Liquids. Measures two times lower than any other Vortex Meter. Heavy Duty & Maintenance Free Design C&C Machined from

More information

5001TCP SPEED CONTROLLER

5001TCP SPEED CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER WARNING Disconnect all incoming power before working on this equipment. Follow power lockout procedures. Use extreme caution around electrical

More information

Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual

Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual COMPANY Paddle Wheel Turbine Flow Meters Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:PADDLEMAN082416 Mechanical Specifications Flow Meter with Polypropylene

More information

5001TCP SPEED CONTROLLER

5001TCP SPEED CONTROLLER VARIABLE SPEED DRIVE CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER With PC101 Torque Limit Control WARNING Disconnect all incoming power before working on this equipment. Follow

More information

Insertion turbine INSTRUCTION SHEET. TECHNICAL PRODUCT

Insertion turbine INSTRUCTION SHEET.   TECHNICAL PRODUCT TECHNICAL PRODUCT INSTRUCTION SHEET Insertion turbine OVERVIEW These insertion flow transducers provide a cost effective and simple means of measuring the flow of a wide range of low viscosity liquids.

More information

Appendix. Clearance. Skewed profiles. Application Schematics

Appendix. Clearance. Skewed profiles. Application Schematics Appendix Application Schematics The purpose of the application schematics is to show different applications and the best sensor location for a particular application. Clearance Because the sensor will

More information

Sierra 780S Series Flat-Trak Mass Flow Meter. Instruction Manual

Sierra 780S Series Flat-Trak Mass Flow Meter. Instruction Manual Series 780S Instruction Manual Table of Contents Sierra 780S Series Flat-Trak Mass Flow Meter Instruction Manual Part Number IM-78S 07/99 Revision B 5 Harris Court, Building L Monterey, CA 93940 (831)

More information

Hydro-Flow 2200 Fixed Insertion Vortex Flow Meter

Hydro-Flow 2200 Fixed Insertion Vortex Flow Meter A trademark of Spirax Sarco, Inc. Hydro-Flow 2200 Fixed Insertion Vortex Flow Meter Description The Hydro-Flow Model 2200 fixed insertion vortex flow meter was designed specifically for water flow measurement,

More information

Sanitary Turbine Flow Meter - TA3 Installation, Operating & Maintenance Manual

Sanitary Turbine Flow Meter - TA3 Installation, Operating & Maintenance Manual COMPANY Sanitary Turbine Flow Meter - TA3 Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:SANITARYMAN16 Mechanical Specifications Measuring Accuracy ± 1.0%

More information

IP80-Series FLOW SENSOR INSTRUCTIONS IP81 IP :2008 ISO CERTIFIED COMPANY IP80-SERIES FLOW SENSOR INSTRUCTIONS

IP80-Series FLOW SENSOR INSTRUCTIONS IP81 IP :2008 ISO CERTIFIED COMPANY IP80-SERIES FLOW SENSOR INSTRUCTIONS IP80-SERIES FLOW SENSOR INSTRUCTIONS IP80-Series FLOW SENSOR INSTRUCTIONS IP81 IP82 9 001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Features, Specifications...Page 3 Installation

More information

F-1500 SERIES INSERTION TURBINE FLOW METER FEATURES Belcher Road South, Largo, FL USA Tel +1 (727) Fax +1 (727)

F-1500 SERIES INSERTION TURBINE FLOW METER FEATURES Belcher Road South, Largo, FL USA Tel +1 (727) Fax +1 (727) F-1500 SERIES INSERTION TURBINE FLOW METER Insertion turbine flow meters are ideal for use in larger steam lines where downsizing the line size to improve flow measurement is not desirable. In these applications,

More information

ULTRAFLO 2000 ULTRASONIC LIQUID FLOW AND HEAT/ENERGY METERS FOR PERMANENT INSTALLATION HIGH TEMPERATURE SENSORS AS STANDARD

ULTRAFLO 2000 ULTRASONIC LIQUID FLOW AND HEAT/ENERGY METERS FOR PERMANENT INSTALLATION HIGH TEMPERATURE SENSORS AS STANDARD ULTRASONIC LIQUID FLOW AND HEAT/ENERGY METERS HIGH TEMPERATURE SENSORS AS STANDARD FOR PERMANENT INSTALLATION ULTRASONIC LIQUID FLOW AND HEAT/ENERGY METERS The Ultraflo 2000 is a Transit Time ultrasonic

More information

VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Loop Powered Mass Flow Meters. Instruction Manual

VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Loop Powered Mass Flow Meters. Instruction Manual Series M22/M23 Instruction Manual Table of Contents VorTek Series M22 and M23 Pro-V Multi-Parameter Vortex Loop Powered Mass Flow Meters Models M22-VT, M22-VTP, M23-VT, M23-VTP Instruction Manual Document

More information

F-2500 SERIES VORTEX METER

F-2500 SERIES VORTEX METER F-500 SERIES VORTEX METER APPLICATIONS Saturated steam Hot water to F (0 C) Applications with optional pressure sensor Superheated steam to F (0 C) Compressed air Industrial gases CALIBRATION Each meter

More information

700 Series FluidVision

700 Series FluidVision Proteus Industries Inc. 700 Series FluidVision Metering Flow, Temperature & Pressure Switches Installation & Operating Instructions 700IM-003 Page 1 of 16 March 2007 Contents: Page Section 1: Introduction

More information

TFA Flowmeter for Saturated Steam Service Installation and Maintenance Instructions

TFA Flowmeter for Saturated Steam Service Installation and Maintenance Instructions 1930051/2 IM-P193-03 MI Issue 2 TFA meter for Saturated Steam Service Installation and Maintenance Instructions This guide must be read in conjunction with the Installation and Maintenance Instructions

More information

IP800-Series FLOW SENSOR INSTRUCTIONS IP810 IP :2008 ISO CERTIFIED COMPANY IP800-SERIES FLOW SENSOR INSTRUCTIONS

IP800-Series FLOW SENSOR INSTRUCTIONS IP810 IP :2008 ISO CERTIFIED COMPANY IP800-SERIES FLOW SENSOR INSTRUCTIONS -SERIES FLOW SENSOR INSTRUCTIONS -Series FLOW SENSOR INSTRUCTIONS IP810 IP820 9001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Features, Specifications...Page 3 Installation Insertion

More information

Low Profile Insertion Vortex

Low Profile Insertion Vortex Low Profile Insertion Vortex Product Features The same insertion meter can measure Steam, Gases or Liquids. Standardize on an insertion bar that can measure line sizes 2 24 Heavy Duty & Maintenance Free

More information

M SERIES Multi-Jet Cold Water Meter

M SERIES Multi-Jet Cold Water Meter M SERIES Multi-Jet Cold Water Meter /4 1 1-1/2" 2" Maximum Flow GPM 0 0 1 Minimum Flow GPM.2.7 1. 2.0 Maximum Operating Pressure 0 psi Maximum Operating Temperature F ( C) Also Available in Hot Water Applications

More information

Vortex Plate. Model VP General Specification. Product Features

Vortex Plate. Model VP General Specification. Product Features Vortex Plate Product Features Our Inline meters can measure Steam, Gases or Liquids. Heavy Duty & Maintenance Free Design C&C Machined from one piece of solid stainless steel Absolutely NO o-rings or seals

More information

F-1500 SERIES INSERTION TURBINE FLOW METER

F-1500 SERIES INSERTION TURBINE FLOW METER F-1500 SERIES INSERTION TURBINE FLOW METER APPLICATIONS Saturated steam Hot water to 450 F (232 C) standard 850 F (454 C) optional Applications with optional pressure sensor Superheated steam to 450 F

More information

IP800-Series FLOW SENSOR INSTRUCTIONS IP810 IP :2008 ISO CERTIFIED COMPANY IP80-SERIES FLOW SENSOR INSTRUCTIONS

IP800-Series FLOW SENSOR INSTRUCTIONS IP810 IP :2008 ISO CERTIFIED COMPANY IP80-SERIES FLOW SENSOR INSTRUCTIONS IP80-SERIES FLOW SENSOR INSTRUCTIONS IP800-Series FLOW SENSOR INSTRUCTIONS IP810 IP820 9001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Features, Specifications...Page 3 Installation

More information

Model 1100 Turbine Flow Meter

Model 1100 Turbine Flow Meter Model 1100 Turbine Flow Meter INSTALLATION & INSTRUCTION MANUAL 8635 Washington Avenue Racine, Wisconsin 53406 Tel: 800-433-5263 or 262-639-6770 Fax: 800-245-3569 or 262-639-2267 www.hedland.com TABLE

More information

Hydro-Flow Model 2300 Installation and Operation Guide B

Hydro-Flow Model 2300 Installation and Operation Guide B Hydro-Flow Model 2300 Installation and Operation Guide 5700508-B Contents: Understanding and Identifying Your Flow Meter 1 Installing Your Flow Meter 3 Electrical Connections.. 7 Mechanical and Electrical

More information

GE Sensing. PanaFlow MV. Vortex Flowmeter. User s Manual

GE Sensing. PanaFlow MV. Vortex Flowmeter. User s Manual GE Sensing PanaFlow MV Vortex Flowmeter User s Manual GE Sensing Panaflow MV Vortex Flowmeter User s Manual 910-279A June 2007 Warranty Each instrument manufactured by GE Sensing, Inc. is warranted to

More information

F-2600 SERIES INLINE VORTEX FLOW METER

F-2600 SERIES INLINE VORTEX FLOW METER F-2600 SERIES ININE VORTEX FOW METER APPICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F (260 C)

More information

Hydro-Flow Model 2200 Fixed Insertion Vortex Flowmeter Installation and Operation Manual

Hydro-Flow Model 2200 Fixed Insertion Vortex Flowmeter Installation and Operation Manual Hydro-Flow Model 00 Fixed Insertion Vortex Flowmeter Installation and Operation Manual Table of Contents Model and Suffix Codes. Theory and Identification.. Installation Guidelines 4 Mechanical Drawing:

More information

Instruction Manual Vortex Flow Meter DVH / DVE

Instruction Manual Vortex Flow Meter DVH / DVE Instruction Manual Vortex Flow Meter DVH / DVE Customer Notice for Oxygen Service Unless you have specifically ordered Heinrichs` optional O 2 cleaning, this flow meter may not be fit for oxygen service.

More information

BI-DIRECTIONAL INSERTION FLOW TRANSDUCER

BI-DIRECTIONAL INSERTION FLOW TRANSDUCER DUALPULSE BI-DIRECTIONAL INSERTION FLOW TRANSDUCER INSTRUCTION MANUAL DUALPULSE LOCK 1.1 General arrangement Thank you for purchasing a Dualpulse Flowmeter. It is important that you read this manual to

More information

BI-DIRECTIONAL INSERTION METER

BI-DIRECTIONAL INSERTION METER BI-DIRECTIONAL INSERTION METER INSTRUCTION MANUAL LOCK 1 Contents CONTENTS PAGE 1.0 INTRODUCTION 1.1 General arrangement 2 1.2 Overview 3 1.3 Operating principal 3 1.4 Specifications 3 2.0 INSTALLATION

More information

WMX-series MUNICIPAL/INDUSTRIAL MAGMETER INSTRUCTIONS

WMX-series MUNICIPAL/INDUSTRIAL MAGMETER INSTRUCTIONS -series MUNICIPAL/INDUSTRIAL MAGMETER INSTRUCTIONS -SERIES MUNICIPAL/INDUSTRIAL MAGMETER INSTRUCTIONS 101 104 The Leader in Flow Meter Value Table of Contents General Information General Information,

More information

Flow Measurement Solutions for Water & Waste Water INSTALLATION OPERATION & MAINTENANCE MANUAL

Flow Measurement Solutions for Water & Waste Water INSTALLATION OPERATION & MAINTENANCE MANUAL Flow Measurement Solutions for Water & Waste Water INSTALLATION OPERATION & MAINTENANCE MANUAL Table of Contents SECTION 1 - INTRODUCTION Specifications... 2 Dimensions... 2 Flow Ranges... 2 SECTION 2

More information

The full WeatherTRAK Flow3 Installation and Maintenance Manual is available online at

The full WeatherTRAK Flow3 Installation and Maintenance Manual is available online at Installation Manual INTRODUCTION The full WeatherTRAK Flow Installation and Maintenance Manual is available online at www.weathertrak.com General Description A WeatherTRAK Flow combines a hydraulic master

More information

SIGNET 7002 Vortex Flow Sensor ENGLISH

SIGNET 7002 Vortex Flow Sensor ENGLISH SIGNET 7002 Vortex Flow Sensor ENGLISH 3-7002.090 C-7/02 English SAFETY INSTRUCTIONS 1. Do not remove from pressurized lines. 2. Never install sensor without O-Rings. 3. Confirm chemical compatibility

More information

Instruction manual. Smart Thermal Mass Flow Meter. TYPE : 3000S Series. ientek Co., Ltd.

Instruction manual. Smart Thermal Mass Flow Meter. TYPE : 3000S Series. ientek Co., Ltd. Instruction manual Smart Thermal Mass Flow Meter TYPE : 3000S Series ientek Co., Ltd. Factor 2 (P)153-803 Daeryung Technotown 5th #407 493, Gasan-dong Gumcheon-Gu, Seoul, Korea TEL : +82-2-2107-7999 FAX

More information

VorTek Series M22, M23 and M24 Pro-V Vortex Volumetric and Mass Flow Meters. Instruction Manual

VorTek Series M22, M23 and M24 Pro-V Vortex Volumetric and Mass Flow Meters. Instruction Manual Table of Contents VorTek Series M22, M23 and M24 Pro-V Vortex Volumetric and Mass Flow Meters Instruction Manual Document Number M-000-00010 Rev 8/2018 8475 W I-25 Frontage Rd Suite 300 Longmont, CO 80504

More information

TABLE OF CONTENTS Service Information 2 Quick Start Instructions 4-5 Introduction 6 Specifications 6 Controls and Terminology

TABLE OF CONTENTS Service Information 2 Quick Start Instructions 4-5 Introduction 6 Specifications 6 Controls and Terminology 1 2 TABLE OF CONTENTS Service Information... 2 Quick Start Instructions... 4-5 Introduction... 6 Specifications... 6 Controls and Terminology... 7 Transducer Mounting Locations... 8 Mounting the Transducer...

More information

Inline Ultrasonic Flowmeter

Inline Ultrasonic Flowmeter M-1500 Series Installation and Operating Manual The M-1500 series is an inline primary flow sensor and externally mounted controller unit. The flow sensor is a straight through flow tube that uses Transit

More information

ONICON Insertion Turbine Flow Meters Single Turbine vs. Dual Turbine Selection Criteria

ONICON Insertion Turbine Flow Meters Single Turbine vs. Dual Turbine Selection Criteria ONICON Insertion Turbine s Single Turbine vs. Dual Turbine Selection Criteria The purpose of this guide is to provide customers and specifying engineers with information about how to choose between ONICON's

More information

TECHNICAL DATASHEET#TD1516AX 3 AMP SOLENOID DRIVER

TECHNICAL DATASHEET#TD1516AX 3 AMP SOLENOID DRIVER TECHNICAL DATASHEET#TD1516AX 3 AMP SOLENOID DRIVER User Selectable V or ma Input Bipolar or Unipolar 0-3A Output Adjustable Dither and PWM Frequency PCB Board or Packaged in Metal Housing P/N: RSD-x-3A-y

More information

VORTAB FLOW CONDITIONERS. For Flow Meters, Pumps and Other Flow Profile Critical Equipment

VORTAB FLOW CONDITIONERS. For Flow Meters, Pumps and Other Flow Profile Critical Equipment VORTAB FLOW CONDITIONERS For Flow Meters, Pumps and Other Flow Profile Critical Equipment Reduce flow meter straight-run requirements into just a few diameters Balance pump inlet flow to eliminate premature

More information

Figure 1: WPR2 Dimensions and Hardware

Figure 1: WPR2 Dimensions and Hardware Installation and Operation Instructions WPR2 Series (Max. Line Pressure < 300 PSI) Wet to Wet Differential Pressure Ø0.200" 2.60" 4.47" 5.47" 5.28" 3.00" Precautions Figure 1: WPR2 Dimensions and Hardware

More information

240/241 Series Vortex Volumetric and Mass Flow Meters. Instruction Manual

240/241 Series Vortex Volumetric and Mass Flow Meters. Instruction Manual Sierra 240/241Series Instruction Manual Table of Contents 240/241 Series Vortex Volumetric and Mass Flow Meters Models: 240-V, VT, VTP, LP / 241-V, VT, VTP, LP, Cryogenic Instruction Manual Document Number

More information

F-2600 & F-2700 Series Vortex Flow Meter Installation and Operation Guide

F-2600 & F-2700 Series Vortex Flow Meter Installation and Operation Guide FLOW AND ENERGY MEASUREMENT F-2600 & F-2700 Series Vortex Flow Meter Installation and Operation Guide 11451 Belcher Road South, Largo, FL 33773 USA Tel +1 (727) 447-6140 Fax +1 (727) 442-5699 www.onicon.com

More information

Armstrong In-Line and Insertion Vortex Flow Meters

Armstrong In-Line and Insertion Vortex Flow Meters Armstrong In-Line and Insertion Vortex Flow Meters Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit for up-to-date information. 1 In-Line

More information

TX800-Series FLOW SENSOR INSTRUCTIONS. TX81x TX82x 9 001:2008 ISO CERTIFIED COMPANY TX800-SERIES FLOW SENSOR INSTRUCTIONS

TX800-Series FLOW SENSOR INSTRUCTIONS. TX81x TX82x 9 001:2008 ISO CERTIFIED COMPANY TX800-SERIES FLOW SENSOR INSTRUCTIONS TX800-SERIES FLOW SENSOR INSTRUCTIONS TX800-Series FLOW SENSOR INSTRUCTIONS TX81x TX82x 9 001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Generial Information, Features...Page 3 Specifications...Page

More information

SL Series Application Notes. SL Series - Application Notes. General Application Notes. Wire Gage & Distance to Load

SL Series Application Notes. SL Series - Application Notes. General Application Notes. Wire Gage & Distance to Load Transportation Products SL Series - Application Notes General Application Notes vin 2 ft. 14 AWG The SL family of power converters, designed as military grade standalone power converters, can also be used

More information

TX 115/215 Hot-tap Insertion Turbine Instructions

TX 115/215 Hot-tap Insertion Turbine Instructions TX 115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.

More information

Fluid Flow Conditioning

Fluid Flow Conditioning Fluid Flow Conditioning March 2014 Flow Conditioning There is no flow meter on the market that needs flow conditioning. All flow meters are effective without any type of flow conditioning. 1 Flow Conditioning

More information

Satellite photo of cloud vortices caused by a mountain (Courtesy of our friends at NASA) tekvorx Operation Showing Simplified Construction

Satellite photo of cloud vortices caused by a mountain (Courtesy of our friends at NASA) tekvorx Operation Showing Simplified Construction Sensing the pulse of industry tekvorx TV01 Multivariable Vortex flow Sensors Vortex flow sensors derive their name from a natural phenomenon of fluid dynamics. When a gas or relatively low viscosity liquid

More information

RUN ACCUM. TOTAL STOP BAT LOW HIGH

RUN ACCUM. TOTAL STOP BAT LOW HIGH TURBOPULSE TURBINE FLOWMETER INSTRUCTION MANUAL gal RUN ACCUM. TOTAL STOP BAT LOW HIGH RESET > PROGRAM ENTER ACCUM TOTAL ^ RATE TOTAL TP050 TABLE OF CONTENTS 1. INTRODUCTION Overview 1 1.1 Model number

More information

Liquid Turbine Flowmeter

Liquid Turbine Flowmeter NUFLO Liquid Turbine Flowmeter User Manual 167018 Explosion-proof for use in Class I, Division I, Groups A, B, C, D Hazardous Environments ANSI 12.27.01-2003 Single Seal Part No. 9A-100062201, Rev. 01

More information

LEVEL AND FLOW MEASUREMENT WS131 FLOW METER USER MANUAL.

LEVEL AND FLOW MEASUREMENT WS131 FLOW METER USER MANUAL. LEVEL AND FLOW MEASUREMENT WS131 FLOW METER USER MANUAL www.enoscientific.com Eno Scientific PO Box 1586 Hillsborough, NC 27278 USA www.enoscientific.com 910-778-2660 Copyright Notice Copyright 2015 Eno

More information

FUNDAMENTALS OF ORIFICE METERING Ken Embry FMC Measurement Solutions

FUNDAMENTALS OF ORIFICE METERING Ken Embry FMC Measurement Solutions FUNDAMENTALS OF ORIFICE METERING Ken Embry FMC Measurement Solutions 6677 N. Gessner, Houston, Texas 77040 Throughout the oil and gas industry, there stems the need for accurate, economical measurement

More information

GPM Hydraulic Flow Meter User Manual

GPM Hydraulic Flow Meter User Manual 4278 100 GPM Hydraulic Flow Meter User Manual Introduction The OTC 4278 Hydraulic Flow Meter has been designed for easy connection to a hydraulic circuit so that flow, pressure and temperature can be readily

More information

BOILER BLOWDOWN CONDUCTIVITY CONTROLLER (CONTINUOUS METHOD)

BOILER BLOWDOWN CONDUCTIVITY CONTROLLER (CONTINUOUS METHOD) LAKEWOOD INSTRUMENTS MODEL 260 SERIES BOILER BLOWDOWN CONDUCTIVITY CONTROLLER (CONTINUOUS METHOD) INSTALLATION & OPERATION MANUAL SERIAL #: Lakewood Instruments 7838 North Faulkner Road, Milwaukee, WI

More information

REMOTE MOUNT SOLENOID DRIVER (0-5 VDC/0-20 ma/10k Potentiometer Input)

REMOTE MOUNT SOLENOID DRIVER (0-5 VDC/0-20 ma/10k Potentiometer Input) REMOTE MOUNT SOLENOID DRIVER (0-5 VDC/0-20 ma/10k Potentiometer Input) Part No.: PCB Board - RSD-PCB-5V-x DIN Rail Mount RSD-DR-5V-x Packaged Driver (board installed in metal box) Available with no cable

More information

Hydro-Flow Model 2200 Installation and Operation Guide B

Hydro-Flow Model 2200 Installation and Operation Guide B Hydro-Flow Model 2200 Installation and Operation Guide 5700507-B Contents: Understanding and Identifying Your Flow Meter 1 Installing Your Flow Meter 3 Making Electrical Connections. 7 Mechanical and Electrical

More information

Turbine Flow Meter Series Turbine Meter USER MANUAL

Turbine Flow Meter Series Turbine Meter USER MANUAL Turbine Flow Meter 1100 Series Turbine Meter USER MANUAL Turbine Flow Meters, 1100 Series CONTENTS Introduction......................................................................... 3 Operating Principle....................................................................

More information

Technical Data Sheet , Rev HB October Rosemount 8800 Vortex Installation Effects

Technical Data Sheet , Rev HB October Rosemount 8800 Vortex Installation Effects Technical Data Sheet 00816-0100-3250, Rev HB October 2018 Rosemount 8800 Vortex Installation Effects 2 Technical Data Sheet Contents 00816-0100-3250 October 2018 Contents Chapter 1 Introduction... 5 1.1

More information

Tracer VM with User Interface

Tracer VM with User Interface Tracer with User Interface Flowmeter with FCI (Fluid Characteristic Indication) Operating Instructions General The Tracer Flowmeter provides: 0 to 5V or 0 to 10V Selectable Analog Flow Output 0 to 5V or

More information

IP800-Series. Insertion Paddlewheel Flow Sensor Instructions PROUDLY MADE IN THE USA

IP800-Series. Insertion Paddlewheel Flow Sensor Instructions PROUDLY MADE IN THE USA IP800-Series Insertion Paddlewheel Flow Sensor Instructions PROUDLY MADE IN THE USA ISO 9001:2008 Certified Company TABLE OF CONTENTS General Information General Information...Page 3 Features...Page 3

More information

EX100/200-Series INSERTION MAGNETIC FLOW METER INSTRUCTIONS EX110 EX210 EX150 EX :2008 ISO CERTIFIED COMPANY

EX100/200-Series INSERTION MAGNETIC FLOW METER INSTRUCTIONS EX110 EX210 EX150 EX :2008 ISO CERTIFIED COMPANY EX100/200-SERIES INSERTION MAGNETIC FLOW METER INSTRUCTIONS EX100/200-Series INSERTION MAGNETIC FLOW METER INSTRUCTIONS EX110 EX210 EX150 EX250 9 001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General

More information

200 Series Flow Meters

200 Series Flow Meters Proteus Industries Inc. 200 Series Flow Meters Technical Reference Manual Can we Improve? Tell our President! Can we improve our product, our support or this manual? We are committed to continuous improvement

More information

Ultrasonic Two-Wire Point Level Control with Tip-Type Sensor

Ultrasonic Two-Wire Point Level Control with Tip-Type Sensor Ultrasonic Two-Wire Point Level Control with Tip-Type Sensor General Instructions The Ultrasonic Point Level Control produces an 8mA or l6ma current to indicate liquid presence/absence within a sensor

More information

VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service

VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service Installation Instructions VA-908x Code No. LIT-12011566 Issued August 24, 2009 Applications The VA-908x Series Electric

More information

TX115/215 Hot-tap Insertion Turbine Instructions

TX115/215 Hot-tap Insertion Turbine Instructions TX115/215 Hot-tap Insertion Turbine Instructions General Information These hot tap versions of the proven TX insertion flow sensors are designed to install or be serviced without depressurizing the pipe.

More information

Sierra Series 240 and 241 Innova-Mass Multi-Parameter Vortex Mass Flow Meters. Instruction Manual

Sierra Series 240 and 241 Innova-Mass Multi-Parameter Vortex Mass Flow Meters. Instruction Manual Series 24-HP Instruction Manual Table of Contents Sierra Series 240 and 241 Innova-Mass Multi-Parameter Vortex Mass Flow Meters Models 240-VT, 240-VTP, 241-VT, 241-VTP Instruction Manual Part Number: IM-24-HP,

More information

A Member of the. Integrated Metering Technologies

A Member of the. Integrated Metering Technologies I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies 1.0 General and Safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe

More information

Transmitting Transducer. Gas/Air Velocity Range:

Transmitting Transducer. Gas/Air Velocity Range: RNG Series Insertion-Style Gas Flow Meter The RNG Series meter is an insertion-style vortex shedding flow meter designed to offer high accuracy measurements over an extremely large flow range. The meters

More information

Type 500X. Electropneumatic Transducer (I/P, E/P) Installation, Operation and Maintenance Instructions. Ordering Information.

Type 500X. Electropneumatic Transducer (I/P, E/P) Installation, Operation and Maintenance Instructions. Ordering Information. Type 500X Electropneumatic Transducer (I/P, E/P) Installation, Operation and Maintenance Instructions Ordering Information Type 500X I/P Transducers Output Range Part Number Input psi kpa Impedance 500-AA

More information

DVH / DVE. Vortex Flow Meter. Instruction Manual. Page 1 of 102

DVH / DVE. Vortex Flow Meter. Instruction Manual. Page 1 of 102 Vortex Flow Meter DVH / DVE Instruction Manual Page 1 of 102 Contents 1 IDENTIFICATION... 5 1.1 Supplier / Manufacturer... 5 1.2 Producttype... 5 1.3 Issue date... 5 1.4 Version No.... 5 1.5 Tagging /

More information

INSTALLATION AND INSTRUCTION

INSTALLATION AND INSTRUCTION MODEL 10A INSTALLATION AND INSTRUCTION MANUAL 399 RESERVATION ROAD MARINA, CA 93933 100133 Revision O Revision O ECO0452 07/02/08 NOTICE This publication must be read in its entirety before performing

More information

HDI inch Choke Position Indicator User s Manual Rev Indicator Gauge Linear Potentiometer

HDI inch Choke Position Indicator User s Manual Rev Indicator Gauge Linear Potentiometer HDI 2522 4-inch Choke Position Indicator User s Manual Rev 2 New 2522 Indicator Gauge Linear Potentiometer w/open Housing 2200 Indicator Gauge Linear Potentiometer TABLE OF CONTENTS HDI 2522 4-inch Indicator

More information

6 Gauge Box Set with Programmable Speedometer. Made in the USA. Caution. Speedometer Parts. Tachometer Parts. Fuel Level Gauge Parts.

6 Gauge Box Set with Programmable Speedometer. Made in the USA. Caution. Speedometer Parts. Tachometer Parts. Fuel Level Gauge Parts. 6 Gauge Box Set with Programmable Speedometer Caution Disconnect the battery during installation. Tighten nuts on the backclamp only slightly more than you can tighten with your fingers. Six inch-pounds

More information

Installation Instructions for LED Timing Light

Installation Instructions for LED Timing Light Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW The P/N 120001 includes a versatile controller

More information

AD592/592-10K Non-Room Sensors in BAPI-Box, BAPI-Box 2 or BAPI-Box 4 BA/592-x-(BB, BB2, BB4) Temperature Sensor Instructions & Operation

AD592/592-10K Non-Room Sensors in BAPI-Box, BAPI-Box 2 or BAPI-Box 4 BA/592-x-(BB, BB2, BB4) Temperature Sensor Instructions & Operation 592 Theory of Operation The 592 sensor is a two terminal integrated-circuit temperature sensor. The 592 provides an output current directly proportional to absolute temperature. When the temperature of

More information

Issue Date: February 1998

Issue Date: February 1998 Issue Date: February 1998 Horizontal Mount (Standard) Vertical Mount (Optional) TABLE OF CONTENTS Page SECTION 1.0 -GENERAL 1 1.1 Measuring System... 1 1.2 Operating Principal... 1 1.3 Application to Magnetic

More information

VIM20 Vortex Insertion Flowmeter

VIM20 Vortex Insertion Flowmeter Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

ULTRASONIC FLOW SENSOR IFX-M4-01

ULTRASONIC FLOW SENSOR IFX-M4-01 ULTRASONIC FLOW SENSOR IFX-M4-01 TECHNICAL DESCRIPTION, OPERATING INSTRUCTION IFX-M4-01 2012-09-10 TABLE OF CONTENTS 1. APPLICATION... 3 2. TECHNICAL DATA... 4 3. PACKAGE CONTENT... 6 4. OPERATING PRINCIPLE...

More information