Secondary Diagnosis. By Randy Bernklau
|
|
- Shavonne Long
- 5 years ago
- Views:
Transcription
1 Secondary Diagnosis Most technicians have diagnosed secondary ignition systems using the large console-type analog scopes, but there are times when it just isn t practical to use an analyzer that is that large. When presented with a problem that needs to be checked quickly, or in a remote location, a hand-held digital storage oscilloscope (DSO) may be a better choice. Now that many technicians have purchased DSOs, its time to learn how to set up a DSO to view an ignition pattern. Some DSOs have presets that will allow a secondary pattern to be displayed without knowing how to adjust time per division or voltage levels. However, many DSOs must be adjusted manually to view the pattern. Even if yours has presets, you may find it necessary to readjust the scope to analyze a specific problem. At first, viewing ignition patterns on a DSO may appear differently than on an ignition scope, but by adjusting the DSO you can bring the pattern to a more recognizable picture. With a little practice you may find the DSO can be used in place of a larger, more expensive console-mounted scope. By Randy Bernklau 29
2 Secondary Diagnosis Your DSO configuration may vary, but many of the items I will discuss can be used on all scopes. The first thing to consider are the leads. The capacitance lead is used for reading secondary ignition. It is clamped around the coil wire and connected to channel 1 of your scope. Check with your supplier for a secondary lead. With the lead connected, adjust the scope. Most of us are familiar with viewing secondary ignition patterns with the voltage spike going up. This is actually upside down. To get this view, select the invert function on the scope. Without this function, you must view the pattern upside down. Alternate depending on the coil side for DIS. The volts per division setting will vary depending on your lead s voltage ratio. My lead reduces the voltage by 100 times, so I set the scope to 10 or 20 volts per division depending on secondary voltage. A normal voltage of 6,500 volts will be displayed as 65 volts. This fits nicely on a 20 volt scale. A lower voltage scale helps provide detail.
3 The next step is to supply a trigger to stabilize the pattern. You can trigger on the coil wire but using a separate lead on number 1 plug wire is best. Use an inductive lead and connect number 1 to external trigger or Channel 2. When using Channel 2, adjust the trigger point, then turn Channel 2 off. This helps clean up the screen. Setting up the time scale is a little more difficult. It depends on what you are trying to examine. Lets start with 500 microseconds per division. This provides a good view of the firing line and burn time. Depending on the trigger source you are using, the screen will show all patterns or just number 1. This can be used to your advantage.
4 Secondary Diagnosis Using the inductive trigger and the scope set in Normal mode, the DSO draws a trace when a trigger is present. This means you know the pattern is only showing the number 1 cylinder. By moving the trigger lead, you can display any other cylinder. Most DSOs screens are small. This method give you the best detail for any single cylinder firing event. Changing the trigger to the capacitance lead allows you to view all cylinders. Detail is still retained but when a problem is seen, it is impossible to tell which cylinder is causing the problem. This method is best for cursory checks or to find the overall burn time. It is also good for coil, wire and rotor gap checks. At times it may be more important to view all firings in a parade view. In most cases you will need peak detect. Failure to do this will result in missing firing lines. Make sure you are triggering off the inductive lead on the number 1 plug wire. To get parade mode, adjust the time per division to a higher setting. 10 ms is a good place to start. How can we tell which cylinder is which in parade view? Since we are triggering from external trigger, we know that number 1 cylinder is the one at the trigger point. In this example the trigger point is to the left side and number 1 is the first firing event. If you are using normal mode and the pattern is freezing, you are losing the trigger. 33
5 Secondary Diagnosis When you lose the trigger, the pattern stops. This means you are missing an event. Switch to auto mode to see why. It may be the trigger level is set to high or number 1 cylinder may be misfiring. This pattern shows a fouled plug which causes a lower firing line. The result can be an intermittent loss of trigger when the plug misfires. Now that we know how to set up the DSO, let s look at a simple ignition problem. This Toyota Pickup came in with a misfire under load that felt like an ignition problem. I connected the DSO and set it to 10 ms and 20 volts. I soon realized the pattern was off the screen and readjusted the volts to 50. I left peak detect off. You can see the firing voltage is too high on one cylinder. The first pattern in this image is 21,000 volts at idle. High firing voltage indicates high resistance. In this case it was caused by an open plug wire. You can see why peak detect should be on. The normal wires appear to lack any voltage kick. With peak detect on they would look normal. This diagnosis was easy. With a new set of wires this truck is ready to go. The tough problems to solve are the intermittents. Getting to know at a glance what is normal and what isn t will help when you are trying to catch a random misfire problem. Secondary ignition analysis is an important skill that takes time to master. 34
6 This is a normal pattern after the wires were replaced. The KV range is good and burn time appears normal. Also the slant of the burn time is normal. When looking at the pattern live, the KV lines will bounce up and down slightly. Excessive bounce is a good indication of a lean mixture or possible excessive EGR flow. Now it s time for something new. I started looking at this several months ago and haven t worked out all the bugs yet. Spread the pattern out to 5 to 20 microseconds per division and observe the rising edge of the voltage spike. Two things come into play. The first is the double peak that you see. This is caused by the voltage jumping two gaps. As you see in this waveform, the double peak is gone. This is because it is taken from a distributorless ignition system. The double peak in the previous example was caused by the spark jumping the rotor gap and the spark plug. This allows you to measure the actual rotor gap voltage. This is a quick way to check for rotor condition. Checking the rising edge of the secondary signal is the second part of this analysis. I have noticed when the edge is hashy or rough, it means the spark is jumping multiple gaps. Check for loose plug wires or corrosion on the coil wire. Try this method of secondary analysis using your DSO. I would be glad to hear how it works for you. 35
Selected excerpts from the book: Lab Scopes: Introductory & Advanced. Steven McAfee
Selected excerpts from the book: Lab Scopes: Introductory & Advanced Steven McAfee 1. 2. 3. 4. 5. 6. Excerpt from Chapter 1 Lab Scopes How do they work? (page 6) Excerpt from Chapter 3 Pattern Recognition
More informationAUTOMOTIVE IGNITION SYSTEMS
AUTOMOTIVE IGNITION SYSTEMS ABSTRACT This report describes the differences and similarities between a 1964 Mustang traditional ignition system and that of my 2014 Jeep. To help you understand the process
More informationIGNITION SYSTEM COMPONENTS AND OPERATION
69 IGNITION SYSTEM COMPONENTS AND OPERATION Figure 69-1 A point-type distributor from a hot rod being tested on a distributor machine. WARNING: The spark from an ignition coil is strong enough to cause
More informationModule 22 Ignition Systems - Outputs
Module 22 Ignition Systems - Outputs Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443 Greensboro,
More informationUSING A DIGITAL STORAGE OSCILLOSCOPE IN 2016
4210 rue Jean-Marchand, Quebec, QC G2C 1Y6, Canada Phone: 418 688 9067 / 800 567 0791 / 810 222 4525 (USA) Fax: 418 843 3444 / Email: info@ A ConsuLab presentation USING A DIGITAL STORAGE OSCILLOSCOPE
More informationO2 Sensor Diagnostics
O2 Sensor Diagnostics This article is a description of various Oxygen Sensor related faults and their value during diagnostics. Overview We will be discussing cases covering both 1V oxygen sensors (or
More informationTroubleshooting A Vintage Distributor Ignition System
Troubleshooting A Vintage Distributor Ignition System -Henry P. Olsen When the owners of vintage carburetor- and distributor-equipped vehicles see that a shop has a big-box engine analyzer, they believe
More informationAUTOMOTIVE TECHNOLOGY Electricity and Electronics
AUTOMOTIVE TECHNOLOGY Electricity and Electronics Al Santini Retired, College of DuPage Glen Ellyn, Illinois Jack Erjavec, Series Editor Professor Emeritus, Columbus State Community College Columbus, Ohio
More informationTHE FOURTH STATE. Gaining a universal insight into the diagnosis of automotive ignition systems. By: Bernie Thompson
THE FOURTH STATE Gaining a universal insight into the diagnosis of automotive ignition systems By: Bernie Thompson Did you know that the forth state of matter powers the spark ignition internal combustion
More information16.01 Theory Module INPUTS
16.01 Theory Module INPUTS Crankshaft position sensor Camshaft position sensor Knock sensor (some engine types) Barometric pressure sensor Intake air temperature sensor Engine coolant temperature sensor
More informationIs there still a place for the vacuum
Is there still a place for the vacuum gauge? We re living in a world that s filled with engines that may never need a valve job and that adjust their own ignition timing, monitor their own misfire conditions
More informationATASA 5 th. ATASA 5 TH Study Guide Chapter 28 Pages Ignition Diagnosis & Service 62 Points. Please Read the Summary
ATASA 5 TH Study Guide Chapter 28 Pages 836 873 62 Points Please Read the Summary Before We Begin Keeping in mind the Career Cluster of Transportation, Distribution & Logistics Ask yourself: What TDL careers
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More information2003 Audi A4 testing
2003 Audi A4 testing An Audi A4 equipped with a 1.8L AMB turbocharged engine was in for service. The owner had just received it back from his kid, indicating it was neglected, having few if any oil changes
More informationLadies and Gentlemen... We Have Ignition!
FEATURE Ladies and Gentlemen... We Have Ignition! The coordination of ignition, fuel delivery and basic engine function is required before internal combustion can take place. Here, we'll look at the ignition
More informationModule 12 Throttle Position (TP) Sensor
Module 12 Throttle Position (TP) Sensor Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443
More informationDTC P0300 Random/Multiple Cylinder Misfire Detected
DI56 EINE (2RZFE, 3RZFE) DI8ZU01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC
More informationMissing Mini. There are two situations we dislike extremely. The. Quick Test
The Missing Mini No, this is not a mystery about a Mini that has gone missing. This car had been off the road for a year s storage in a body shop. When it came time to return the vehicle to the customer,
More informationSensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask.
Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Contents 1. Introducing Electronic Ignition 2. Inductive Ignition 3. Capacitor Discharge Ignition 4. CDI vs
More informationIgnition System Inspection and Component Testing (Distributor Vehicle)
JOB SHEET 92 Ignition System Inspection and Component Testing (Distributor Vehicle) Name:-------------- Station: Date: NATEF Correlation This Job Sheet addresses the following NATEF task(s): 8.C.2 8.C.3
More information))) FirstLook. User's Guide. FirstLook Automotive Engine Diagnostic Sensor "The Pulse of Your Engine" Model ADS ES 100.
))) FirstLook User's Guide FirstLook Automotive Engine Diagnostic Sensor "The Pulse of Your Engine" Model ADS ES 1 Table of Contents Section Page 1. Introduction 2 2. Overview 2. Theory of Operation 2.
More informationPart 1. Reduced fuel flow due to a restricted inlet screen. Sluggish plunger movement due to contamination.
http://www.datec.us/instructor/ More about the author http://www.datec.us /instructor SCREEN Part 1 There is not a good way to check the fuel distribution per cylinder. The intention of this session is
More informationCatalytic Converter Testing
Catalytic Converter Testing The first catalytic converter was created before the use of onboard computer systems its job was to oxidize HC and CO into CO2 and H2O. The term oxidizes means to add O2 to
More informationDownload Automotive Electricity & Electronics Books
Download Automotive Electricity & Electronics Books Today's automotive technicians need a thorough understanding of electrical principles and electronic systems to service modern vehicles. With Automotive
More informationThe PCM is the on-board computer which receives input from various sensors and, with this information, controls various engine & emissions control
The PCM is the on-board computer which receives input from various sensors and, with this information, controls various engine & emissions control actuators. The PCM has various memories within it. These
More informationDTC P0300 Random/Multiple Cylinder Misfire Detected
EINE (5VZFE) DI301 DIB1V01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304
More informationTempest Tech-Tip 0813
August 2013 Tempest Tech-Tip 0813 Light My Fire Background Without a good spark, spark plugs can t get the job done well. How do you keep good sparks coming, so your spark plugs can light your fire with
More informationFire in the Hole. Choosing a set of racing spark. Racing Spark Plugs. By Larry Carley, Technical Editor
Fire in the Hole Racing By Larry Carley, Technical Editor lcarley@babcox.com Choosing a set of racing spark plugs for a particular application is not as easy as it sounds because the plugs have to be closely
More informationDTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 05 149 059VJ 07 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER
More informationVacuum Readings for Tuning and Diagnosis
Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider
More informationDTC P1300 Igniter Circuit Malfunction (No.1) DTC P1305 Igniter Circuit Malfunction (No.2) DTC P1310 Igniter Circuit Malfunction (No.
DIAGNOSTICS EINE (RZFE, RZFE) DI 9 DI6 DTC P00 Igniter Circuit Malfunction (No.) DTC P05 Igniter Circuit Malfunction (No.) DTC P0 Igniter Circuit Malfunction (No.) DTC P5 Igniter Circuit Malfunction (No.)
More informationTiming is everything with internal combustion engines By: Bernie Thompson
Timing is everything with internal combustion engines By: Bernie Thompson As one goes through life, it is said that timing is everything. In the case of the internal combustion engine, this could not be
More informationDTC P1300 Igniter Circuit Malfunction
DI3 EINE (VZFE) DISD DTC P3 Igniter Circuit Malfunction CIRCUIT DESCRIPTION A Direct Ignition System (DIS) has been adopted. The DIS improves the ignition timing accuracy, reduces highvoltage loss, and
More informationIgnition System Fundamentals
Ignition System Fundamentals Chapter 37 Objectives Describe the functions of ignition system parts Explain the operation of points, electronic, and computer ignition systems Give an overview of the different
More informationWide Band EFIE Installation Instructions. Locate the wide band oxygen sensor current wire
Wide Band EFIE Installation Instructions Install your fuel efficiency device The EFIE is not intended to be a fuel saver by itself. You should install a device that is designed to get more energy out of
More informationF - BASIC TESTING Article Text 1992 Dodge Colt For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Saturday, April 27, :48PM
Article Text ARTICLE BEGINNING 1992 ENGINE PERFORMANCE Chrysler Motors/Mitsubishi Basic Diagnostic Procedures Chrysler Motors: Colt, Colt 200, Summit Mitsubishi: Mirage INTRODUCTION The following diagnostic
More informationAsk COBB BMW Misfire Diagnose and Repair. By Ian Armstrong
Ask COBB BMW Misfire Diagnose and Repair By Ian Armstrong Introduction There s nothing better than adding some more power to your car; whether it s bolting on some new downpipes, crimping some wires, or
More informationH - TESTS W/O CODES Nissan 240SX INTRODUCTION TROUBLE SHOOTING SYMPTOMS DIAGNOSIS WILL NOT START
H - TESTS W/O CODES 1990 Nissan 240SX 1990 ENGINE PERFORMANCE Trouble Shooting - No Codes Nissan; 240SX, Axxess, Maxima, Pathfinder, Pickup, Pulsar, Sentra, Van, INTRODUCTION Before diagnosing symptoms
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationDTC P0300-P0308. Diagnostic Instructions. DTC Descriptors. Circuit/System Description. Conditions for Running the DTC
Page 1 of 5 2009 GMC Truck Sierra - 2WD Sierra, Silverado (VIN C/K) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, 6.0L, 6.2L, or 7.0L Description and Operation DTC P0300-P0308 Diagnostic Instructions
More information2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition. History. Customer bought used about 3 months ago
2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition History Customer bought used about 3 months ago Claims since day one runs rough on cold start Sometimes MIL would
More informationM ost vehicle manufacturers offer many
Using the CSS Script for Unconventional Diagnostic Methods Have you ever wondered why engine control systems from different manufacturers have common principles and similar designs, but are diagnosed using
More informationCurrent Clamp, clamped around the starter wire. Pico Scope. Relative Compression Test on a 2007 Honda Accord SE 4CYL
P a g e 1 Relative Compression Test on a 2007 Honda Accord SE 4CYL A relative compression test is performed by monitoring the electrical current to the starter while cranking the engine over. The amount
More informationDTC P1300 Igniter Circuit Malfunction No.1. DTC P1310 Igniter Circuit Malfunction No.2
DIAGNOSTICS EINE (5SFE) DI63 DI0G06 DTC P300 Igniter Circuit Malfunction No. DTC P30 Igniter Circuit Malfunction No.2 CIRCUIT DESCRIPTION The ECM determines the ignition timing, turns on Tr at a predetermined
More informationNATEF ENGINE PERFORMANCE CHECKLIST Name Date Period
NATEF ENGINE PERFORMANCE CHECKLIST Name Period For every task in Engine Performance the following safety requirement must be strictly enforced: Comply with personal and environmental safety practices associated
More informationSolarity with InfoTech Software Solarity, powered by Genisys technology, is a powerful 4-channel scope with the functionality required to analyze the most sophisticated vehicles. InfoTech Software provides
More informationHigh technology theft-prevention systems
Lemme In! Mazda 626 & MPV Immobilizer System High technology theft-prevention systems have hit the automotive market full-force. Several manufacturers now offer antitheft protection integrated with the
More informationMSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020
INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition
More informationTable of Contents. General Information...1. Components...2. Connection...4
Table of Contents General Information... Components... Connection...4 Interface of Main Unit...4 Oscilloscope...5 Multimeter...5 Voltage, Current, Resistance, Duty Cycle, Frequency and Battery Voltage...5
More informationA/C Generator Systems
A/C Generator Systems What is the function of the charging system? Provide power for all electrical loads Recharge the starting battery What happens if the charging systems puts out too much power? Voltage
More informationTesting electronic ignition system with variable characteristics EZL
15-1250 Testing electronic ignition system with variable characteristics EZL Operation no. of operation texts and work units or standard texts and flat rates: 15-1250. Connection diagram for engine tester
More informationDealing with customer concerns related to electronic throttle bodies By: Bernie Thompson
Dealing with customer concerns related to electronic throttle bodies By: Bernie Thompson In order to regulate the power produced from the gasoline internal combustion engine (ICE), a restriction is used
More informationDTC P0300 Random/Multiple Cylinder Misfire Detected
DI60 DI5DI03 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
More informationIgnition Coil Current Waveforms 2007 Honda Accord SE 4CYL
P a g e 1 Ignition Coil Current Waveforms 2007 Honda Accord SE 4CYL With a current clamp and a cheap scope, it is easy to monitor the ignition coil currents and quickly diagnose a bad ignition coil. The
More informationAsynchronous Restriking CDI 2 channel
Asynchronous Restriking CDI 2 channel Parts List ARC-2 module Decals Power Cable Fuse Specifications Operating Voltage: 8-20V Operating Current: Max Operating RPM: Ambient Temp range: Ignition inputs:
More informationDTC P0300 Random/Multiple Cylinder Misfire Detected
DIAGNOSTICS EINE (5VZFE) DI57 DI8XH02 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected
More informationEVENING PROGRAM DESCRIPTIONS. California State Smog Repair Technician
EVENING PROGRAM DESCRIPTIONS California State Smog Repair Technician School Name: Smog Tech Institute Course Name: Smog Repair Technician Course Number: TBA Program Title: Californian State Smog Repair
More informationHappy Birthday OBD II Emission Control System becomes diagnostic tool
FEATURE ARTICLE Happy Birthday OBD II Emission Control System becomes diagnostic tool 4 Bring out the birthday cake and light the candles, the second generation of onboard diagnostics, universally known
More informationEveryday Diagnostics
Page 1 of 11 Pico Technology Everyday Diagnostics Mercedes S-Class Misfire By Andy Cape, Cape Auto Diagnostics, Cape Town Vehicle details: 1995 Mercedes W140 S-Class M119 V8 Engine Background information
More informationDTC P0300 Random/Multiple Cylinder Misfire Detected
DI63 DI7DE01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
More informationTrouble Shooting Instructions
Customer: Date: Trouble Shooting Instructions Electroair Acquisition Corp. 317 Catrell Dr., Suite #2 Howell, MI 48843 USA Ph: 517-552 552-9390 Fax: 517-552 552-9391 Email: sales@electroair.net Electroair
More informationDTC P0351 Ignition Coil A Primary/Secondary Circuit. DTC P0352 Ignition Coil B Primary/Secondary Circuit
DI06 DIAGNOSTICS EINE DIAFC0 DTC P05 A Primary/Secondary Circuit DTC P05 B Primary/Secondary Circuit DTC P05 C Primary/Secondary Circuit DTC P05 D Primary/Secondary Circuit CIRCUIT DESCRIPTION A Direct
More informationCatalytic Failures. Engine running too hot.
Catalytic Failures It is not uncommon for technicians to misdiagnose a driveability or emissions issue by blaming the converter. In many cases, it s not the converter s fault, but rather one of the engine
More informationI ve had lots of requests recently for
The right picture can be worth a thousand words. Here, circuit diagrams and oscilloscope patterns aid in visualizing the effects of resistance at two locations in a series circuit. Mark Warren smwarren@motor.com
More informationFUEL-06, Throttle Position Switch - Information, Troubleshooting, Replacement, and Adjustment
FUEL-06, Throttle Position Switch - Information, Troubleshooting, Replacement, and Adjustment Introduction A faulty throttle position switch (TPS) can result in a number of poor running problems. Because
More informationCPU-95 ADVANCED DIGITAL IGNITION SYSTEM FOR INDUSTRIAL ENGINES
New Backward-Compatible Enhanced CPU-95 Display Now Available CPU-95 ADVANCED DIGITAL IGNITION SYSTEM FOR INDUSTRIAL ENGINES Microprocessor-based, crankshaft referenced digital ignition system for medium-sized
More informationSERVICE BULLETIN. Legacy D* Outback D* Impreza 4-Door D* Impreza 5-Door XV Crosstrek D* Forester E* BRZ D*607924
ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT - All Service Personnel Should Read and Initial in the boxes provided, right. SERVICE BULLETIN APPLICABILITY:
More informationDTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 05157 059VJ13 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4
More informationDTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 0539 059VJ09 DTC P030 CYLINDER MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4 MISFIRE
More informationModule 11 Thermistor Inputs
Module 11 Thermistor Inputs Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443 Greensboro,
More informationChapter 4 Ignition & Electrical Systems
Chapter 4 Ignition & Electrical Systems Chapter 4 Section A Study Aid Questions Fill in the Blanks 1. Ignition systems can be divided into two classifications: systems or systems for reciprocating engines.
More information(P0135/P0155), (P0141/P0161), (P1131/P1151), (P1132/P1152). To further clarify this, see the more detailed scenario as follows:
1. Always reset KAM after performing a repair: After performing a repair on a vehicle with the MIL on, and/or DTCs present, always clear KAM. When a malfunction is present, the PCM adapts (attempts to
More informationBASIC ELECTRICAL MEASUREMENTS By David Navone
BASIC ELECTRICAL MEASUREMENTS By David Navone Just about every component designed to operate in an automobile was designed to run on a nominal 12 volts. When this voltage, V, is applied across a resistance,
More informationArrow Shark TS760-Marine Onboard E-Starter. Owner Manual
Arrow Shark TS760-Marine Onboard E-Starter Owner Manual The TS760-Marine Onboard E-Starter has concluded years of experience Arrow Shark has on RC boat onboard E-Starter, it will work for about all brands
More informationF - BASIC TESTING Infiniti G20 INTRODUCTION PRELIMINARY INSPECTION & ADJUSTMENTS VISUAL INSPECTION MECHANICAL INSPECTION
F - BASIC TESTING 1992 Infiniti G20 1992 ENGINE PERFORMANCE Infiniti Basic Diagnostic Procedures G20, M30, Q45 INTRODUCTION The following diagnostic steps will help prevent overlooking a simple problem.
More informationLearning Guide EMISSION SPECIALIST 5 GAS ANALYSIS COURSE NUMBER: E001-01
Learning Guide EMISSION SPECIALIST 5 GAS ANALYSIS COURSE NUMBER: E001-01 Notice Due to the wide range of vehicles makes and models, the information given during the class will be general in nature and
More informationDTC P1300 Igniter Circuit Malfunction (No. 1) DTC P1305 Igniter Circuit Malfunction (No. 2) DTC P1310 Igniter Circuit Malfunction (No.
DI DIHD DTC P00 Igniter Circuit Malfunction (No. ) DTC P05 Igniter Circuit Malfunction (No. ) DTC P0 Igniter Circuit Malfunction (No. ) DTC P5 Igniter Circuit Malfunction (No. ) CICUIT DESCIPTION A Direct
More informationALTERNATOR - CHRYSLER 40/90-AMP & 50/120 AMP
ALTERNATOR - CHRYSLER 40/90-AMP & 50/120 AMP 1988 Chrysler LeBaron Convert/Coupe 1988 ELECTRICAL Chrysler Motors 40/90 & 50/120 Amp Alternators FWD Models DESCRIPTION The charging system consists of an
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationATASA 5 th. ATASA 5 TH Study Guide Chapter 31 Pages EFI Diagnosis & Service 47 Points. Please Read The Summary
ATASA 5 TH Study Guide Chapter 31 Pages 922 948 47 Points Please Read The Summary 1. Troubleshooting EFI systems requires step by step test procedures mostly due to the many interrelated components and
More informationBooks ,000 Books Before Kindergarten
1 2 3 4 5 Books 1-50 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 41 32 42 33 43 34 44 35 45 36 46 37 47 38 48 39 49 40 50 Sing with your child! Singing slows down your natural
More informationDYNAMIC DUO. Lab scopes and current
DYNAMIC DUO Combining the data acquisition capabilities of a lab scope with the versatility of a current probe gives you a powerful diagnostic tandem that s awfully hard to beat. BY MARK WARREN Lab scopes
More informationANTI-LOCK BRAKING SYSTEM (ABS)
35B-1 GROUP 35B ANTI-LOCK BRAKING SYSTEM (ABS) CONTENTS GENERAL DESCRIPTION......... 35B-2 ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS.................... 35B-3 INTRODUCTION TO ANTI-LOCK BRAKE SYSTEM DIAGNOSIS................
More informationUser s Manual ENGINE IGNITION ANALYZER. General Technologies Corp.
User s Manual ENGINE IGNITION ANALYZER General Technologies Corp. Table of Contents 1. Safety Rules Page 1 2. Technical Specifications Page 2 2.1 General specifications Page 2 2.2 Electrical specifications
More informationCPU-XL VariSpark ADVANCED DIGITAL IGNITION SYSTEM FOR LARGE GAS ENGINES
CPU-XL VariSpark ADVANCED DIGITAL IGNITION SYSTEM FOR LARGE GAS ENGINES n State-of-the-art, crankshaft-referenced digital ignition system for natural-gas fueled integral compressor engines n Innovative
More informationElectromagnets & Induction Vocabulary
Electromagnets & Induction Vocabulary Term Definition Coil Solenoid Electric Motor Parts of an electric motor: Rotor commutator armature brushes Electromagnetic Induction Faraday s Law of Induction Generator
More informationLambda Control Fuel Adaptation and Fuel Trim
Lambda Control Fuel Adaptation and Fuel Trim Q: What is Lambda and Lambda Control? A: In the case of a gasoline engine, the optimal mixture of air to fuel for complete combustion is a ratio of 14.7 parts
More informationIgnition Timing - Honda 180-Degree Twins
Ignition Timing - Honda 180-Degree Twins First thing to do is make a quick test light - I used a 12 volt indicator bulb from a speedo. Test leads with alligator clips make hookup easy... The point plate
More informationMSD Zero-Cross Distributor Chevrolet - PN 83971
MSD Zero-Cross Distributor Chevrolet - PN 83971 Parts Included: 1 Distributor 1 Gasket 1 Hold Down & Hardware 1 Gear Lubricant 2 O-Rings IMPORTANT The Separate Pickup Zero-Cross Distributors use two completely
More informationInstallation Instructions
Installation Instructions 8 Channel C 2 D Ignition System PN 30-2800 4 Channel C 2 D Ignition System PN 30-2801 WARNING: This installation is not for the electrically challenged! Use this ignition with
More informationDTC P1351 Ignition Coil Control Circuit High Voltage
Page 1 of 5 1996 Chevrolet Chevy K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Document ID: 34079 DTC P1351 Ignition Coil Control Circuit High Voltage Circuit
More informationBSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines
BSR BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines Features Digital Advance The main feature of the Magic Box is the digital advance that replaces conventional weights and springs.
More informationEnergy, the Environment and Transportation Natural Gas Reciprocating Engine Technolgy July 24, 2012
Energy, the Environment and Transportation Natural Gas Reciprocating Engine Technolgy July 24, 2012 Introduction 2 Dave Petruska Engineering Manager at Woodward Licensed Professional Engineer (PE) BS and
More informationSetup Tabs. Basic Setup: Advanced Setup:
Setup Tabs Basic Setup: Password This option sets a password that MUST be entered to re-enter the system. Note: ProEFI can NOT get you into the calibration if you lose this password. You will have to reflash
More informationIn the first part of this series on
by Mike Van Dyke In the first part of this series on diagnosing ECUs, we went over some basic visual diagnosis of common failures. In this, the second part of the series, we re going to go over some basic
More information1 of 2 9/4/ :27 AM
Ford Mustang IAC IAB - Solving your idle problems http://www.muscularmustangs.com/iac.php 1 of 2 9/4/2010 10:27 AM Solving idle problems part 1 - Cleaning your IAC Does your idle rise and fall over and
More informationDTC P0300/93 Random/Multiple Cylinder Misfire Detected (European spec.) DTC P0301/93 Cylinder 1 Misfire Detected (European spec.)
DI7 DI63Z0 DTC P0300/93 Random/Multiple Cylinder Misfire Detected (European spec.) DTC P030/93 Cylinder Misfire Detected (European spec.) DTC P030/93 Cylinder Misfire Detected (European spec.) DTC P0303/93
More informationTri-Spark - Classic Triple Trident & R3 Installation Instructions
Tri-Spark - Classic Triple Trident & R3 Installation Instructions TRI-0002 Copyright Tri-Spark 2015 Revised June 2015 Thank you for purchasing the Tri-Spark Classic Triple Ignition system. For your own
More informationBooks READING TIP
Books 1-100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 TRACK YOUR READING AND WIN PRIZES! Bring your Reading Logs to any library to pick up your prizes! 25 Books: a small prize 100 Books: a tote
More informationTroubleshooting of the LubeTech Grease System
Troubleshooting of the LubeTech Grease System February 2009 The LubeTech grease system is designed to be a preventative maintenance system that will extend the life of your bearings that are connected
More information