ACC CUT RELAY INSPECTION

Size: px
Start display at page:

Download "ACC CUT RELAY INSPECTION"

Transcription

1 STARTING (2UZFE) ACC CUT RELAY ACC CUT RELAY INSPECTION 1. REMOVE ACC CUT RELAY Remove the cowl side trim board LH and ACC cut relay. ST21 ST0Q102 Continuity No continuity Continuity S INSPECT ACC CUT RELAY CONTINUITY (a) Using an ohmmeter, check that there is continuity between terminals 1 and 2. If there is no continuity, replace the relay. (b) Check that there is no continuity between terminals 3 and 5. If there is continuity, replace the relay. (c) Check that there is continuity between terminals 3 and 4. If there is no continuity, replace the relay. Battery No Continuity Continuity 2 5 S INSPECT ACC CUT RELAY OPERATION (a) Apply battery positive voltage across terminals 1 and 2. (b) Using an ohmmeter, check that there is no continuity between terminals 3 and 4. If there is continuity, replace the relay. (c) Using an ohmmeter, check that there is continuity between terminals 3 and 5. If there is no continuity, replace the relay. 4. REINSTALL ACC CUT RELAY 3824

2 ST2 STARTING (2UZFE) COMPONENTS ST0GK03 Suction Hose MAF Meter Wire Throttle Body Cover PS Air Hose Vacuum Hose PCV Hose Intake Air Connector Nonreusable part B

3 STARTING (2UZFE) ST3 Engine Wire and Clamp Intake Manifold Assembly Injector Connector Fuel Return Hose 10 (102, 7 ) Air Switching Valve No.2 Gasket 10 (102, 7 ) VSV Connector for EVAP Gasket Engine Wire Gasket 10 (102, 7 ) Starter 39 (400, 29) Gasket Starter Connector 10 (102, 7 ) Engine Wire Protector N m (kgf cm, ft lbf) : Specified torque Nonreusable part B

4 ST4 STARTING (2UZFE) 1.4 kw Type Bearing Idler Gear Starter Housing Assembly Dust Protector Front Bearing Armature Magnetic Switch Assembly Starter Clutch Assembly Steel Ball ORing Rear Bearing Return Spring ORing Brush Holder ORing Field Frame (Field Coil) ORing Dust Protector End Cover Magnetic Switch Assembly Terminal Insulator Terminal Nut Contact Plate 17 (170, 13) Wave Washer Terminal Insulator ORing Terminal Bolt Terminal C Kit Part Gasket Lead Terminal Plunger End Cover ORing Packing Terminal Insulator Wave Washer Terminal Bolt Terminal Nut 17 (170, 13) Contact Plate Terminal Insulator Terminal 30 Kit Part N m (kgf cm, ft lbf) : Specified torque Nonreusable part B

5 STARTING (2UZFE) ST5 2.0 kw Type Bearing Idler Gear Starter Housing Assembly Dust Protector Armature Front Bearing Magnetic Switch Assembly Starter Clutch Assembly Steel Ball ORing Rear Bearing Return Spring Brush Holder ORing ORing Field Frame (Field Coil) ORing End Cover Dust Protector Magnetic Switch Assembly Terminal Insulator Terminal Bolt Terminal Nut Contact Plate 17 (170, 13) Wave Washer Terminal Insulator ORing Lead Terminal Gasket Plunger Terminal C Kit Part End Cover Terminal Bolt Contact Plate Terminal Insulator ORing Packing Terminal Insulator Wave Washer Terminal Nut 17 (170, 13) Terminal 30 Kit Part N m (kgf cm, ft lbf) : Specified torque Nonreusable part B

6 Dust Protector STARTING (2UZFE) B04550 ST7 ST08D03 DISASSEMBLY 1. REMOVE 2 DUST PROTECTORS 2. REMOVE FIELD FRAME AND ARMATURE (a) Remove the nut, and disconnect the lead wire from the magnetic switch terminal. Torque: 5.9 N m (60 kgf cm, 52 in. lbf) (b) Remove the 2 through bolts. Torque: 1.4 kw type: 5.9 N m (60 kgf cm, 52 in. lbf) 2.0 kw type: 9.3 N m (95 kgf cm, 82 in. lbf) B04632 (c) Pull out the field frame together with the armature from the magnetic switch assembly. NOTICE: At the time of notice, please refer to the following items. Align the protrusion of the field frame with the groove of the magnetic switch. (d) Remove the Oring from the field frame. HINT: At the time of assembly, please refer to the following items. Use a new Oring. 3. REMOVE HOUSING, CLUTCH ASSEMBLY AND GEAR (a) 1.4 kw type: Remove the 2 bolts. Torque: 5.9 N m (60 kgf cm, 52 in. lbf) (b) 2.0 kw type: Remove the 2 screws. Torque: 9.3 N m (95 kgf cm, 82 in. lbf) B04551 Idler Gear Return Spring Bearing Starter Housing Starter Clutch Assembly B04552 (c) Remove the starter housing, return spring, idler gear, bearing and starter clutch assembly. HINT: At the time of assembly, please refer to the following item. Apply grease to the return spring and insert the return spring into the clutch shaft hole. 3810

7 ST8 STARTING (2UZFE) Magnetic Finger 4. REMOVE STEEL BALL Using a magnetic finger, remove the steel ball from the clutch shaft hole. HINT: At the time of assembly, please refer to the following item. Apply grease to the steel ball and insert the steel ball into the clutch shaft hole. ST0948 B REMOVE BRUSH HOLDER (a) Remove the 2 screws w/ Oring and end cover from the field frame. Torque: 1.4 kw type: 1.5 N m (15 kgf cm, 13 in. lbf) 2.0 kw type: 3.8 N m (39 kgf cm, 34 in. lbf) (b) Remove the Oring from the field frame. HINT: At the time of assembly, please refer to the following item. Use a new Oring. (c) Using a screwdriver, hold the spring back and disconnect the brush from the brush holder. Disconnect the 4 brushes, and remove the brush holder. NOTICE: Check that the positive (+) lead wires are not grounded. 6. REMOVE ARMATURE FROM FIELD FRAME P

8 Continuity STARTING (2UZFE) ST9 ST0GL03 INSPECTION 1. INSPECT COMMUTATOR FOR OPEN CIRCUIT Using an ohmmeter, check that there is continuity between the segments of the commutator. If there is no continuity between any segment, replace the armature. S00054 No Continuity S INSPECT COMMUTATOR FOR GROUND Using an ohmmeter, check that there is no continuity between the commutator and armature coil core. If there is continuity, replace the armature. 3. INSPECT COMMUTATOR FOR DIRTY AND BURNT SURFACE If the surface is dirty or burnt, correct it with sandpaper (No.400) or on a lathe. 4. INSPECT COMMUTATOR CIRCLE RUNOUT (a) Place the commutator on Vblocks. (b) Using a dial indicator the circle runout. Maximum circle runout: 0.05 mm ( in.) If the circle runout is greater than maximum, correct it on a lathe. S INSPECT COMMUTATOR DIAMETER Using vernier calipers, measure the commutator diameter. Standard diameter: 1.4 kw type 30.0 mm (1.181 in.) 2.0 kw type 35.0 mm (1.378 in.) Minimum diameter: 1.4 kw type 29.0 mm (1.142 in.) S kw type 34.0 mm (1.339 in.) If the diameter is less than minimum, replace the armature. 6. INSPECT UNDERCUT DEPTH Check that the undercut depth is clean and free of foreign materials. Smooth out the edge. Standard undercut depth: 1.4 kw type 0.6 mm (0.024 in.) ST kw type 0.7 mm (0.028 in.) Minimum undercut depth: 0.2 mm (0.008 in.) If the undercut depth is less than minimum, correct it with a hacksaw blade. 3812

9 ST10 STARTING (2UZFE) Continuity 7. INSPECT FIELD COIL FOR OPEN CIRCUIT Using an ohmmeter, check that there is continuity between the lead wire and field coil brush lead. If there is no continuity, replace the field frame. P10588 No Continuity 8. INSPECT THAT FIELD COIL IS NOT GROUNDED Using an ohmmeter, check that there is no continuity between the field coil end and field frame. If there is continuity, repair or replace the field frame. P kw Type (A) (B) kw type: INSPECT SHUNT COIL FOR OPEN CIRCUIT Using an ohmmeter, measure the resistance between shunt coil terminals (A) and (B). Resistance: 1.5 to 1.9 Ω at 20 C (68 F) If the resistance is not as specified, replace the field frame. S02267 Z INSPECT BRUSH LENGTH Using vernier calipers, measure the brush length. Standard length: 1.4 kw type 15.5 mm (0.610 in.) 2.0 kw type 15.0 mm (0.591 in.) Minimum length: 1.4 kw type 10.0 mm (0.394 in.) 2.0 kw type 9.0 mm (0.354 in.) If the length is less than minimum, replace the brush holder and field frame. 3813

10 STARTING (2UZFE) ST INSPECT BRUSH SPRING LOAD Take the pull scale reading the instant the brush spring separates from the brush. Standard spring installed load: 1.4 kw type 17.6 to 23.5 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf) 2.0 kw type 21.5 to 27.5 N (2.2 to 2.8 kgf, 4.8 to 6.2 lbf) Minimum spring installed load: ST kw type 11.8 N (1.2 kgf, 2.7 lbf) 2.0 kw type 12.7 N (1.3 kgf, 2.9 lbf) If the installed load is less than minimum, replace the brush springs. Lock No Continuity Free P INSPECT BRUSH HOLDER INSULATION Using an ohmmeter, check that there is no continuity between the positive (+) and negative () brush holders. If there is continuity, repair or replace the brush holder. 13. INSPECT GEAR TEETH Check the gear teeth on the pinion gear, idle gear and the clutch assembly for wear or damage. If damaged, replace the gear or clutch assembly. If damaged, also check the drive plate ring gear for wear or damage. 14. INSPECT CLUTCH PINION GEAR Rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks. If necessary, replace the clutch assembly. 15. INSPECT FRONT AND REAR BEARING Turn the bearing by hand while applying inward force. If resistance is felt or the bearing sticks, replace the bearing. P DO PULLIN COIL OPEN CIRCUIT TEST Using an ohmmeter, check that there is continuity between terminals 50 and C. If there is no continuity, check and replace the magnetic switch. Terminal C Terminal 50 Continuity B

11 ST12 STARTING (2UZFE) 17. DO HOLDIN COIL OPEN CIRCUIT TEST Using an ohmmeter, check that there is continuity between terminal 50 and the switch body. If there is no continuity, replace the magnetic switch. Terminal 50 Continuity B

12 Starter Connector Engine Wire Protector STARTING (2UZFE) B04549 INSTALLATION ST19 ST08I05 1. INSTALL (a) Install the engine wire protector to the starter with the bolt. Torque: 9.81 N m (100 kgf cm, 84 in. lbf) (b) Connect the starter wire with the nut. Torque: 9.81 N m (100 kgf cm, 84 in. lbf) (c) Connect the starter connector. (d) Connect the starter to the cylinder block. (e) Connect the engine wire with the bolt. B04548 (f) Install the starter with the 2 bolts. Torque: 39 N m (400 kgf cm, 29 ft lbf) 2. INSTALL AIR PUMP ASSEMBLY (See page EC27 ) 3. INSTALL INTAKE MANIFOLD ASSEMBLY (See page EM60 ) 4. CONNECT THROTTLE BODY ASSEMBLY TO INTAKE MANIFOLD (See page SF45 ) 5. INSTALL INTAKE AIR CONNECTOR 6. INSTALL THROTTLE BODY COVER 7. CONNECT CABLE TO NEGATIVE () BATTERY TER MINAL 3822

13 STARTING (2UZFE) ST17 ST08G05 REASSEMBLY Reassembly is in the reverse order of disassembly (See page ST7 ). HINT: At the time of assembly, use hightemperature grease to lubricate the bearing and gears when assembling the starter. 3820

14 ST6 STARTING (2UZFE) ST08C05 REMOVAL 1. REMOVE THROTTLE BODY COVER 2. DISCONNECT CABLE FROM NEGATIVE () BATTERY TERMINAL 3. REMOVE INTAKE AIR CONNECTOR 4. DISCONNECT THROTTLE BODY ASSEMBLY FROM INTAKE MANIFOLD (See pege SF44 ) 5. REMOVE INTAKE MANIFOLD ASSEMBLY (See page EM36 ) 6. REMOVE AIR PUMP ASSEMBLY (See page EC23 ) 7. REMOVE (a) Remove the 2 bolts holding the starter to the cylinder block. (b) Disconnect the starter from the cylinder block. B04548 Engine Wire Protector (c) (d) (e) (f) Disconnect the starter connector. Remove the nut, bolt and disconnect the starter wire. Remove the bolt, and disconnect the engine wire protector from the starter. Remove the starter. Starter Connector B

15 SST STARTING (2UZFE) REPLACEMENT 1. REPLACE REAR BEARING (a) Using SST, remove the bearing. SST ST13 ST08F06 S00058 (b) Using a press, press in a new bearing. S00059 SST 2. REPLACE FRONT BEARING (a) Using SST, remove the bearing. SST S00060 Upward SST (b) Using SST and a press, press in a new bearing. NOTICE: Be careful of the bearing installation direction. SST Downward S REPLACE MAGNETIC SWITCH TERMINAL KIT PARTS (a) Remove magnetic switch end cover. Remove the 3 bolts, end cover, gasket and plunger. B

16 ST14 STARTING (2UZFE) (b) Inspect contact plate for wear. Using vernier calipers, measure the contact plate for depth of wear. Maximum wear: 0.9 mm (0.035 in.) If the depth of wear is greater than the maximum, replace the contact plate. Wear B04555 SST B04556 (c) Remove terminal kit parts. (1) Using SST, loosen the terminal nuts. SST (2) Terminal C: Remove the terminal nut, wave washer, terminal insulator (outside), O ring, terminal bolt, contact plate and terminal insulator (inside). (3) Terminal 30: Remove the terminal nut, wave washer, terminal insulator (outside), O ring, terminal bolt, contact plate, terminal insulator (inside) and insulation paper. (3) Long (2) (1) Short Long Short (4) (5) Inside (6) (7) B07949 (d) Install new terminal 30 kit parts. (1) Temporarily install a new terminal insulator (inside). (2) Temporarily install a new contact plate. (3) Temporarily install a new terminal bolt. (4) Temporarily install a new Oring. (5) Temporarily install a new packing and new terminal insulator (outside). Install a new packing to a new terminal insulator, and install them. HINT: Match the protrusion of the insulator with the indentation of the housing. (6) Temporarily install a new wave washer. (7) Temporarily install a new terminal nut. NOTICE: Be careful to install the terminal insulator (inside) and wave washer in the correct direction. 3817

17 STARTING (2UZFE) ST15 (7) (6) (5) (4) Inside Long (1) Lead Terminal Short (2) (3) B04559 (e) Install new terminal C kit parts. (1) Temporarily install a new terminal insulator (inside). (2) Temporarily install a new contact plate. (3) Temporarily install a new terminal bolt. (4) Temporarily install a new Oring. (5) Temporarily install a new terminal insulator (outside). (6) Temporarily install a new wave washer. (7) Temporarily install a new terminal nut. NOTICE: Be careful to install the terminal insulator (inside) and wave washer in the correct direction. (f) Temporarily tighten the terminal nuts. 40 mm 37 mm Contact Plate 20 mm B04560 (g) Tighten terminal nuts. (1) Put a wooden block on the contact plate and press it down with a hand press. Dimensions of wooden block: 20 x 37 x 40 mm (0.79 x 1.46 x 1.57 in.) Press force: 981 N (100 kgf, 221 lbf) NOTICE: Check the diameter of the hand press ram. Then calculate the gauge pressure of the press when 981 N (100 kgf, 221 lbf) of force is applied. Gauge pressure: (kgf/cm 2 ) = 100 kgf Ram diameter (cm) 2 2 x 3.14 (π) (psi) = 221lbf Ram diameter (in.) 2 2 x 3.14 (π) (kpa) = (kgf/cm 2 ) x 98.1 (kpa) = (psi) x 6.9 If the contact plate is not pressed down with the specified pressure, the contact plate may tilt due to coil deformation or the tightening of the nut. 3818

18 ST16 STARTING (2UZFE) SST (2) Using SST, tighten the nuts to the specified torque. SST Torque: 17 N m (170 kgf cm, 13 ft lbf) NOTICE: If the nut is over tightened, it may cause cracks on the inside of the insulator. B04561 B04562 (h) (i) Clean contact surfaces of contact plate and plunger. Clean the contact surfaces of the remaining contact plate and plunger with a dry shop rag. Reinstall magnetic switch end cover. Install the plunger, new gasket, end cover and lead clamp with the 3 bolts. Torque: 1.4 kw type: 2.5 N m (25 kgf cm, 22 in. lbf) 2.0 kw type: 3.6 N m (37 kgf cm, 32 in. lbf) 3819

19 ST18 Terminal 50 Terminal C Battery STARTING (2UZFE) B04543 ST08H06 TEST NOTICE: These tests must be done within 3 to 5 seconds to avoid burning out the coil. 1. DO PULLIN TEST (a) Disconnect the field coil lead wire from terminal C. (b) Connect the battery to the magnetic switch as shown. Check that the pinion gear moves outward. 2. DO HOLDIN TEST While connected as above with the pinion gear out, disconnect the negative () lead from terminal C. Check that the pinion gear remains out. Disconnect Terminal C Battery B04544 Disconnect 3. INSPECT CLUTCH PINION GEAR RETURN Disconnect the negative () lead from the starter body. Check that the pinion gear returns inward. Battery B04545 Terminal 50 Terminal 30 Battery Ammeter B DO NOLOAD PERFORMANCE TEST (a) Connect the battery and ammeter to the starter as shown. (b) Check that the starter rotates smoothly and steadily with the pinion gear moving out. Check that the ammeter shows the specified current. Specified current: 1.4 kw type 90 A or less at 11.5 V 2.0 kw type 100 A or less at 11.5 V 3821

20 ST20 STARTING (2UZFE) RELAY RELAY INSPECTION 1. REMOVE RELAY BOX COVER 2. REMOVE RELAY (Marking: ST) ST0PK01 1 Continuity No Continuity B INSPECT RELAY (a) Inspect the relay continuity. (1) Using an ohmmeter, check that there is continuity between terminals 1 and 2. If there is no continuity, replace the relay. (2) Check that there is no continuity between terminals 3 and 5. If there is continuity, replace the relay. Battery Continuity B16389 (b) Inspect the relay operation. (1) Apply battery voltage across terminals 1 and 2. (2) Using an ohmmeter, check that there is continuity between terminals 3 and 5. If there is no continuity, replace the relay. 4. REINSTALL RELAY BOX COVER 5. REINSTALL RELAY 3823

21 STARTING (2UZFE) STARTING SYSTEM ONVEHICLE INSPECTION NOTICE: STARTING SYSTEM Before changing the starter, check these items again: Connector connection Accessory installation, e.g.: engine immobilizer system ST1 ST08A

ACC CUT RELAY INSPECTION

ACC CUT RELAY INSPECTION ACC Cut Relay ACC CUT RELAY ACC CUT RELAY INSPECTION 1. REMOVE ACC CUT RELAY Remove the relay box and ACC cut relay. ST19 ST0OU01 B16462 Continuity 4 2 1 5 3 Continuity No continuity S04972 2. INSPECT

More information

STARTING SYSTEM ST 1

STARTING SYSTEM ST 1 STARTING SYSTEM ST1 ST2 STARTING SYSTEM PREPARATION SST (SPECIAL SERVICE TOOLS) PREPARATION Injection Pump Spline Shaft Puller Armature bearing Alternator Rear Bearing Replacer Armature front bearing RECOMMENDED

More information

ON-VEHICLE INSPECTION

ON-VEHICLE INSPECTION CH2 P11586 CHARGING CHARGING SYSTEM ONVEHICLE INSPECTION 1. CHECK BATTERY ELECTROLYTE LEVEL Check the electrolyte quantity of each cell. MaintenanceFree Battery: CH03L01 If under the lower level, replace

More information

STARTING SYSTEM STARTING SYSTEM ST 1

STARTING SYSTEM STARTING SYSTEM ST 1 ST1 ST2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Engine will not crank Battery charge low Battery cables loose, corroded or worn Clutch start switch faulty (M/T) Neutral start

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION (3S GTE)

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION (3S GTE) STARTING SYSTEM ST5 COMPONENTS FOR REMOVAL AND INSTALLATION (3SGTE) REMOVAL (3SGTE) (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Turn the

More information

INSPECTION ST 13 2UZ-FE STARTING STARTER. Terminal 50. Terminal C. Battery. Disconnect Battery. Terminal C. Disconnect. Battery.

INSPECTION ST 13 2UZ-FE STARTING STARTER. Terminal 50. Terminal C. Battery. Disconnect Battery. Terminal C. Disconnect. Battery. 2UZ-FE ARTING ARTER 13 INSPECTION 1. INSPECT ARTER ASSEMBLY NOTICE: These tests must be done within 3 to 5 seconds to avoid burning out the coil. (a) Do pull-in test. (1) Disconnect the field coil lead

More information

ST 9 1GR-FE STARTING STARTER

ST 9 1GR-FE STARTING STARTER 1GR-FE ARTING ARTER 9 (c) Using a screwdriver, hold the spring back and disconnect the 4 brushes from the brush holder. (d) Remove the brush holder from the armature. 4. REMOVE ARTER ARMATURE ASSEMBLY

More information

ST- 1 STARTING SYSTEM. Page TROUBLESHOOTING... ST-2 STARTER... ST-3 STARTER RELAY... ST- 12 CLUTCH START SWITCH... ST-1 2

ST- 1 STARTING SYSTEM. Page TROUBLESHOOTING... ST-2 STARTER... ST-3 STARTER RELAY... ST- 12 CLUTCH START SWITCH... ST-1 2 ST- 1 STARTING SYSTEM Page TROUBLESHOOTING... ST-2 STARTER... ST-3 STARTER RELAY... ST- 12 CLUTCH START SWITCH... ST-1 2 ST-2 STARTING SYSTEM - Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy

More information

OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit.

OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. STARTING & CHARGING 195 OVERHAUL 190C702 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. A57559 (b) (c) (d) Remove the 2 screws

More information

1GR-FE STARTING STARTER (for 4WD) DISASSEMBLY

1GR-FE STARTING STARTER (for 4WD) DISASSEMBLY 14 1GR-FE ARTING ARTER (for 4WD) DISASSEMBLY 1. REMOVE ARTER YOKE ASSEMBLY (a) Remove the nut, then disconnect the lead wire from terminal C. Remove the 2 through bolts. (c) Pull the starter yoke and the

More information

STARTER (for 2WD and Pre-Runner)

STARTER (for 2WD and Pre-Runner) 4 1GR-FE ARTING ARTER (for 2WD and Pre-Runner) ARTER (for 2WD and Pre-Runner) ENGINE 1GR-FE ARTING COMPONENTS 9.3 (95, 82 in.*lbf) BRUSH SPRING x4 ARTER ARMATURE ASSEMBLY O-RING O-RING ARTER YOKE ASSEMBLY

More information

CHAPTER 22 STARTER Models J05C-TD, J08C-TP and TR

CHAPTER 22 STARTER Models J05C-TD, J08C-TP and TR 1 INDEX STARTER 22-1 22-114E-03 CHAPTER 22 STARTER TROUBLESHOOTING...22-2 STARTER...22-4 22 22-2 STARTER 1 page 1 TROUBLESHOOTING Symptom Possible cause Remedy Engine does not crank, or cranks slowly Key

More information

STARTING SYSTEM (1ZZ FE) (April, 2003)

STARTING SYSTEM (1ZZ FE) (April, 2003) STARTING & CHARGING STARTING SYSTEM (1ZZ FE) (April, 2003) STARTING SYSTEM (1ZZ FE) (April, 2003) INSPECTION 19 1 190QO 02 1. INSPECT STARTER ASSY NOTICE: These tests must be performed within 3 to 5 seconds

More information

1 of 16 1/10/2015 7:25 AM STARTER MOTOR 2009 Hyundai Accent 1.6L Eng GS REQUESTED INFORMATION DISASSEMBLY 1. Disconnect the M-terminal (A) on the magnet switch assembly (B). Fig 1: Identifying M-Terminal

More information

INJECTOR COMPONENTS SF-18. Air Cleaner Hose. Accelerator Cable Water Bypass Hose Air Hose. PCV Hose. Throttle Position Sensor Connector.

INJECTOR COMPONENTS SF-18. Air Cleaner Hose. Accelerator Cable Water Bypass Hose Air Hose. PCV Hose. Throttle Position Sensor Connector. SF18 SFI (5VZFE) COMPONENTS SF02204 Air Cleaner Hose PCV Hose Accelerator Cable Water Bypass Hose Air Hose Throttle Position Sensor Connector CCV Hose Accelerator Pedal Position Sensor Connector Throttle

More information

SECTION 9 CRANKING SYSTEM CONTENTS

SECTION 9 CRANKING SYSTEM CONTENTS SECTION 9 CRANKING SYSTEM CONTENTS 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. 9-8. GENERAL DESCRIPTION.,...,..., 9-2 SPECIFICATIONS.......................................... 9-4 LUBRICATION 9-5 REMOVAL AND INSTALLATION...

More information

CHARGING SYSTEM ON-VEHICLE INSPECTION

CHARGING SYSTEM ON-VEHICLE INSPECTION CHARGING (2UZFE) CHARGING SYSTEM CHARGING SYSTEM ONVEHICLE INSPECTION CH1 CH0J603 CAUTION: Check that the battery cables are connected to the correct terminals. Disconnect the battery cables when the battery

More information

STARTING SYSTEM LOCATION INDEX [LF]

STARTING SYSTEM LOCATION INDEX [LF] 1. Remove the battery cover. 2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF].) 3. Remove the side cover. (LH) 2007 Mazda MX-5 Miata Sport 2007 ENGINE Starting System -

More information

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu STARTER - HITACHI 1986 Trooper II 1984 Starters HITACHI DESCRIPTION Starter is a conventional 12-volt, 4-pole brush-type motor, with direct or reduction gear drive. The starter-mounted solenoid shifts

More information

1991 Mazda MX-5 Miata. STARTER - DIRECT DRIVE ELECTRICAL Mazda Starters - Direct Drive ELECTRICAL Mazda Starters - Direct Drive

1991 Mazda MX-5 Miata. STARTER - DIRECT DRIVE ELECTRICAL Mazda Starters - Direct Drive ELECTRICAL Mazda Starters - Direct Drive DESCRIPTION STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM03T03 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal operating

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: ENGINE MECHANICAL (2UZFE) CO/HC CO/HC INSPECTION HINT: EM1 EM0KQ09 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: ENGINE MECHANICAL (1MZFE) CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM0I0 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine

More information

AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM PRECAUTION AUTOMATIC TRANSMISSION SYSTEM If the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: CO/HC CO/HC INSPECTION EM1 EM0KQ07 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) The engine is at normal operating temperature.

More information

./#0#. 1"&." 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift

./#0#. 1&. 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift !"" #$%!& '()!)((*(+,*)- 1994 ELECTRICAL Suzuki of America Corp. - Starters Swift Two types of starter motors are used, conventional and reduction gear. Both types of starters consist of yoke assembly,

More information

DESCRIPTION & OPERATION

DESCRIPTION & OPERATION STARTER - REDUCTION GEAR 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Reduction Gear DESCRIPTION & OPERATION Reduction gear starter is a conventional 12-volt, 4-pole, brush-type starter. The integral

More information

1997 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive

1997 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive DESCRIPTION & OPERATION Direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral

More information

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front

More information

1994 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1994 ELECTRICAL Mazda Starter - Direct Drive

1994 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1994 ELECTRICAL Mazda Starter - Direct Drive DESCRIPTION STARTER - DIRECT DRIVE 1994 ELECTRICAL Mazda Starter - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached

More information

STARTER SYSTEM TESTING 5.6

STARTER SYSTEM TESTING 5.6 STARTER SYSTEM TESTING 5.6 ON-MOTORCYCLE TESTS Starter Relay Test NOTE Starter relay test also applies to ignition and key switch relays.. See Figure 5-5. Locate starter relay. The relay is attached to

More information

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14) EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop

More information

Cylinder Head Setting Bolt Tightening Adaptor Injection Measuring Tool Set EFI Fuel Pressure Gauge

Cylinder Head Setting Bolt Tightening Adaptor Injection Measuring Tool Set EFI Fuel Pressure Gauge SFI SYSTEM (2JZGE) EG187 SFI SYSTEM (2JZGE) PREPARATION SST (SPECIAL SERVICE TOOLS) 0920576030 Cylinder Head Setting Bolt Tightening Adaptor ECT sensor 0926841045 Injection Measuring Tool Set (0926841070)

More information

1994 Mazda MX-5 Miata. STARTER - REDUCTION GEAR 1994 ELECTRICAL Mazda Starter - Reduction Gear

1994 Mazda MX-5 Miata. STARTER - REDUCTION GEAR 1994 ELECTRICAL Mazda Starter - Reduction Gear DESCRIPTION STARTER - REDUCTION GEAR 1994 ELECTRICAL Mazda Starter - Reduction Gear The Nippondenso reduction gear starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is

More information

STARTER SYSTEM TESTING 5.6

STARTER SYSTEM TESTING 5.6 STARTER SYSTEM TESTING 5.6 ON-MOTORCYCLE TESTS b088x5x Starter Relay Test NOTE Starter relay test also applies to ignition and key switch relays.. See Figure 5-5. Locate starter relay. The relay is attached

More information

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner. 14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

More information

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER

More information

TIMING BELT COMPONENTS

TIMING BELT COMPONENTS EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL

More information

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE

More information

IGNITION SYSTEM ON VEHICLE INSPECTION NOTICE:

IGNITION SYSTEM ON VEHICLE INSPECTION NOTICE: SYSTEM ONVEHICLE INSPECTION NOTICE: SPARK TEST NO CHECK CONNECTION OF COIL, IGNITER AND DISTRIBUTOR CONNECTOR OK CHECK RESISTANCE OF HIGHTENSION CORD (See step 2) Maximum resistance: 25 kω per cord OK

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. 144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT

More information

FUEL SYSTEM PRECAUTION FU 1

FUEL SYSTEM PRECAUTION FU 1 2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

EG2 173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM

EG2 173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM 5SFE ENGINE EG2173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM EG2174 5SFE ENGINE EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter

More information

FUEL PUMP SYSTEM CIRCUIT

FUEL PUMP SYSTEM CIRCUIT EG190 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the DLC1. SST 0984318020 (b) Turn the ignition switch ON. NOTICE: Do not start

More information

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly. ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE

More information

EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)

EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE) ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination

More information

Throttle Body (4A FE)

Throttle Body (4A FE) Air Induction System (Throttle Body (4AFE)) FI185 Throttle Body (4AFE) Throttle Position Sensor PSW E2 IDL ower oint oving oint F10451 P03147 F15040 F10452 Throttle Position Sensor Idle Point Guide Cam

More information

2000 Toyota Truck Tundra. Timing Belt: Service and Repair

2000 Toyota Truck Tundra. Timing Belt: Service and Repair Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE

More information

FUEL PUMP SYSTEM CIRCUIT

FUEL PUMP SYSTEM CIRCUIT EG1182 22RE ENGINE FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Turn the ignition switch ON. HINT: Do not start the engine. (b) Using SST, connect terminals Fp and +B

More information

COMPONENTS SF-52 ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) Suction Hose. Throttle Body Cover. MAF Meter Wire. Vacuum Hose. PS Air Hose.

COMPONENTS SF-52 ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) Suction Hose. Throttle Body Cover. MAF Meter Wire. Vacuum Hose. PS Air Hose. SF52 SFI (2UZFE) ACOUSTIC CONTROL INDUCTION SYSTEM (ACIS) COMPONENTS SF1XM01 Suction Hose MAF Meter Wire Throttle Body Cover PS Air Hose Vacuum Hose PCV Hose Intake Air Connector B17459 3637 SFI (2UZFE)

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information

Throttle Body (3S GTE)

Throttle Body (3S GTE) FI192 Air Induction System (Throttle Body (3SGTE)) Throttle Body (3SGTE) ONVEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port.

More information

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR

More information

8/14/2016 8:12 PM. Bolt: Part No for Type B

8/14/2016 8:12 PM. Bolt: Part No for Type B 1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR

More information

REMOVE FRONT WHEEL RH

REMOVE FRONT WHEEL RH 518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER

More information

2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE)

2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) 2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) Vehicle» Steering and Suspension» Steering» Steering Gear» Service and Repair» Disassembly and Assembly Part 1 Of 3 Part 2 Of 3 http://alldatapro.com/alldata/pro~v432223842~c41100~r0~od~n/0/101825161/103142888/105946035/110859872/34853741/34864218/34864219/34864308/

More information

FUEL PUMP SYSTEM CIRCUIT

FUEL PUMP SYSTEM CIRCUIT EG199 FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SSt, connect terminals +B and FP of the data link connector 1. SST 0984318020 (b) Turn the ignition switch ON.

More information

TIMING BELT (5S FE) COMPONENTS

TIMING BELT (5S FE) COMPONENTS ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds

More information

POWER STEERING SYSTEM

POWER STEERING SYSTEM SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system

More information

ABBREVIATIONS USED IN THIS

ABBREVIATIONS USED IN THIS IN10 INTRODUCTION ABBREVIATIONS USED IN THIS MANUAL ABBREVIATIONS USED IN THIS MANUAL ATF Automatic Transmission Fluid B 0 Overdrive Brake B 2 Second Brake B 3 No. 3 Brake C 0 Overdrive Direct Clutch C

More information

TURBOCHARGER ON VEHICLE INSPECTION TC 7

TURBOCHARGER ON VEHICLE INSPECTION TC 7 TC7 ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR SYSTEM Check for leakage or clogging between the air cleaner and turbocharger inlet and between the turbocharger outlet and cylinder head. Clogged air cleaner...

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover. 1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket

More information

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U)

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U) Inward Sensor A05060 INSTALLATION EM21 EM0ZD02 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley, and slide on the timing pulley. (b) Install the

More information

OIL AND FILTER INSPECTION

OIL AND FILTER INSPECTION F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.

More information

THROTTLE BODY. ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. EG1 182

THROTTLE BODY. ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. EG1 182 EG1182 THROTTLE BODY ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port. Start the engine. Check the vacuum with your finger.

More information

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft.

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft. EM19 ENGINE MECHANICAL (5VZFE) INSTALLATION EM0Z003 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on

More information

TROUBLESHOOTING PROBLEM SYMPTOMS TABLE

TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TURBOCHARGING (2JZGTE) TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Before troubleshooting the turbocharger, first check the engine itself. (Valve clearance, engine compression, ignition timing

More information

FI 135. Fuel Pump (3S GTE)

FI 135. Fuel Pump (3S GTE) Fuel System (Fuel Pump (3SGTE)) FI135 Fuel Pump (3SGTE) FI136 MFI AND SFI SYSTEMS Fuel System (Fuel Pump (3SGTE)) ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and

More information

STARTING/CHARGING SYSTEMS Brought to you by Eris Studios NOT FOR RESALE

STARTING/CHARGING SYSTEMS Brought to you by Eris Studios NOT FOR RESALE STARTING/CHARGING SYSTEMS General Description 1. General Description A: SPECIFICATION Vehicle model Starter Generator Item Specification Type Reduction type Model 428000-5760 Manufacturer DENSO Voltage

More information

Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity

Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity ENGINE EG329 PREPARATION SST (SPECIAL SERVICE TOOLS) 0923001010 Radiator Service Tool Set 0923114010 Punch 2JZGE only (Aluminum type) RECOMMENDED TOOLS 0904000010 Hexagon Wrench Set 0908200050 TOYOTA Electrical

More information

EMISSION CONTROL SYSTEMS (2JZ GE) SYSTEM PURPOSE

EMISSION CONTROL SYSTEMS (2JZ GE) SYSTEM PURPOSE SYSTEM PURPOSE The emission control systems are installed to reduce the amount of CO, HC and NOx exhausted from the engine ((3), (4) and (5)), to prevent the atmospheric release of blowby gascontaining

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap. 14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.

More information

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets. CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE

More information

STARTER Mitsubishi Montero DESCRIPTION BENCH TESTING STARTER NO-LOAD TEST ELECTRICAL Mitsubishi Starters. Montero

STARTER Mitsubishi Montero DESCRIPTION BENCH TESTING STARTER NO-LOAD TEST ELECTRICAL Mitsubishi Starters. Montero STARTER 1993 Mitsubishi Montero 1993 ELECTRICAL Mitsubishi Starters Montero DESCRIPTION The starter is a conventional 12-volt, 4-pole brush-type motor, with gear reduction drive. The starter-mounted solenoid

More information

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts. 1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.

More information

POWER STEERING PUMP (3VZ FE) POWER STEERING PUMP REMOVAL AND INSTALLATION Remove and install the parts as shown.

POWER STEERING PUMP (3VZ FE) POWER STEERING PUMP REMOVAL AND INSTALLATION Remove and install the parts as shown. STEERING SR41 PUMP (3VZFE) PUMP REMOVAL AND INSTALLATION Remove and install the parts as shown. SR42 STEERING (MAIN POINTS OF REMOVAL AND INSTALLATION) 1. REMOVE PRESSURE TUBES Using SST, remove the pressure

More information

OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY

OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY 1416 OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUBASSY 140RL01. INSPECT CONNECTING ROD THRUST CLEARANCE (a) Using a dial indicator, measure the thrust clearance while moving the connecting rod

More information

TIMING BELT (3S FE) COMPONENTS

TIMING BELT (3S FE) COMPONENTS Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE

More information

FUEL PUMP. ON VEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the data link connector 1.

FUEL PUMP. ON VEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the data link connector 1. EG2250 FUEL PUMP ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Using SST, connect terminals +B and FP of the data link connector 1. SST 0984318020 (b) Turn the ignition switch ON. NOTICE: Do not

More information

OVERHAUL 1. REMOVE GENERATOR PULLEY SST ( , ) HINT:

OVERHAUL 1. REMOVE GENERATOR PULLEY SST ( , ) HINT: 1917 OVERHUL 190CC02 1 B 1 62753 1. REMOVE GENERTOR PULLEY 0982063010 (0982006010, 0982006020) HINT: 1, B 0982006010 2 0982006020 (a) Hold 1 with a torque wrench, and tighten 1 B clockwise to the specified

More information

EXHAUST GAS RECIRCULATION (EGR) SYSTEM

EXHAUST GAS RECIRCULATION (EGR) SYSTEM 3SGTE ENGINE EG1243 EXHAUST GAS RECIRCULATION (EGR) SYSTEM To reduce NOx emissions, part of the exhaust gases is recirculated through the EGR valve to the intake manifold to lower the maximum combustion

More information

GENERAL SPECIFICATIONS

GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION - DESCRIPTION AT-3 GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION -COMPONENT PARTS REMOVAL COMPONENT PARTS REMOVAL COMPONENTS AT-13 Oil Cooler Union Throttle Cable O-Ring A/T Fluid

More information

Drive/Propeller Shaft: Service and Repair

Drive/Propeller Shaft: Service and Repair 2001 Lexus IS 300 L6-3.0L (2JZ-GE) Page 1 Drive/Propeller Shaft: Service and Repair 2001 Lexus IS 300 L6-3.0L (2JZ-GE) Page 2 REMOVAL 1. REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERS 2. REMOVE LH FRONT FLOOR

More information

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket. TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.

More information

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT

More information

CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR

CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR COOLANT COOLANT INSPECTION HINT: Check the coolant level when the engine is cold. 1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR The engine coolant level should be between the LOW and FULL lines at

More information

GENERATOR REMOVAL OF GENERATOR (4A FE) CH 6

GENERATOR REMOVAL OF GENERATOR (4A FE) CH 6 CH6 GENERATOR REMOVAL OF GENERATOR (4AFE) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds or longer from the time the ignition switch is turned

More information

20. Install and tighten the cap screws that hold the end frame and field frame together

20. Install and tighten the cap screws that hold the end frame and field frame together 4006-30 19. Fill the oil reservoir in the bearing bore of the end frame with SAE 10 engine oil. Then put the the end frame on the armature shaft. Align the marks on the end frame and field frame and push

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

Symptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily)

Symptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily) CLUTCH CLUTCH SYSTEM (MTM) PROBLEM SYMPTOMS TABLE HINT: CLUTCH SYSTEM (MTM) Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.

More information

AIR CONTROL VALVE INSPECTION 1. TURN AIR CONDITIONING SWITCH OFF

AIR CONTROL VALVE INSPECTION 1. TURN AIR CONDITIONING SWITCH OFF SR8 AIR CONTROL VALVE Vacuum Hose F04811 AIR CONTROL VALVE INSPECTION 1. TURN AIR CONDITIONING SWITCH OFF SR0LZ06 2. CHECK IDLEUP (a) Start the engine and run it at idle. (b) Fully turn the steering wheel.

More information

SERVICING SPECIFICATIONS (1) ENGINE BODY

SERVICING SPECIFICATIONS (1) ENGINE BODY SERVICING SPECIFICATIONS (1) ENGINE BODY Lubricating oil capacity Oil pan depth 110 mm (4.33 in.) 5.7 L 1.5 U.S.gals (1/14) Oil pan depth 125 mm (4.92 in.) 5.1 L 1.3 U.S.gals Oil pan depth 130 mm (5.12

More information

IGNITION SYSTEM ON-VEHICLE INSPECTION NOTICE:

IGNITION SYSTEM ON-VEHICLE INSPECTION NOTICE: ONVEHICLE INSPECTION SPARK TEST NO CHECK CONNECTION OF COIL CONNECTOR CHANGE IT TO NORMAL COIL (WITH IGNITER) AND PERFORM SPARK TEST AGAIN NO CHECK POWER SUPPLY TO COIL (WITH IGNITER) 1. Turn ignition

More information

EXHAUST GAS RECIRCULATION (EGR) SYSTEM

EXHAUST GAS RECIRCULATION (EGR) SYSTEM ENGINE EG169 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (California only) EG170 ENGINE To reduce NOx emissions, part of the exhaust gases are recirculated through the EGR valve to the intake manifold to lower

More information