MAXITORQ ELECTRICALLY ACTUATED CLUTCHES AND BRAKES
|
|
- Myrtle Haynes
- 5 years ago
- Views:
Transcription
1
2 MAXITORQ ELECTRICALLY ACTUATED CLUTCHES AND BRAKES HOW TO SELECT THE CORRECT CLUTCH OR BRAKE The easiest way is to ask our application engineers. For clutch application, we need to know: Torque or H.P. to be transmitted Speed of the clutch shaft Duty cycle Prime mover (i.e., AC or DC motor, internal combustion engine, etc.) Method of transmitting torque to or from the clutch (sheave, sprocket, etc.) Type of load or mechanism being started This is usually sufficient. However, where acceleration time is important or the duty cycle is grater than 6 per minute we need to know the cycle time, the inertias of the loads being started, and their rotational and/or linear speeds, and the desired starting time. In brake applications, we need to know: H.P. of the drive motor Stopping time desired Duty cycle Speed of the brake shaft Type of load being stopped If the duty cycle is greater than 6 per minute, the thermal energy to be dissipated should be checked against the energy dissipating capacity of the brake. Also, if the stopping speed or accuracy is important, that will influence the choice of the brake size and the control circuit. In both these cases we will need data on the rotational and linear inertias being stopped and their rotational linear speeds, plus the on/off times. The control circuit used is important and we will be glad to assist you in selecting the best control. Tension control applications require special evaluation, since heat dissipation is of major importance and torque is not usually the major factor in choosing the correct clutch or brake. A different type of friction material will also be required, if you want to know more about the calculations and factors to be considered in the selection of a clutch or brake, see the application engineering pages for more data. A REVIEW OF MAXITORQ ARMATURE HUB DESIGNS A feature of the Maxitorq line is the variety of armatures and armature hubs. A clutch coupling connects two in-line shafts, whereas a clutch connects two parallel shafts; therefore, the armature hub designs for these two products are different. The armature hubs used with brakes are the same as those used wit clutch couplings. The following is a brief outline of the standard armature and hub assemblies we offer to meet your requirements and simplify your assembly. Special armature designs are also available, Please call our application engineers if you require more information. For brakes and clutch couplings, we offer three designs: Our flat plate armature is connected to the shaft through a splined hub. It is the lowest cost design and it is widely used. In the anti-backlash design, a flat plate armature is connected to the armature hub by a flat spring. The spring provides zero backlash, fast release and the spline noise is eliminated. For Models 25 and 40 we offer a splined, heavy-duty segmented armature, which provides superior heat dissipation and longer life, and is designed for use in heavy-duty application. An automatic wear follow-up system is optional. In clutch applications, the armature must be connected to a bearing mounted pulley, gear etc., therefore, we offer the following standard designs: Two bearing-mounted hubs, onto which can be mounted the armatures described above. One hub is for use with the splined armatures, and the other is used with the anti-backlash armatures. Self-lubricating sleeve bearings are used. In the 25 and 40 models a keyway is provided on the O.D. of the hub, on which a sprocket or pulley can be counted. In the 12 and 17 models, a knurled hub is supplied. Where customers want to use their own design of bearing-mounted pulley, sprocket, etc., they can use our anti- backlash armature and connect the flat spring directly to their drive component, or they can us a splined hub with a clearance bore and a special connecting flange. RUNNING IN NEW CLUTCHES AND BRAKES With new units the torque can be 30% to 40% below the rated torque until the friction facing and the armature have been run against each other and worn in. This is accomplished by applying about 20% of the rated voltage and slipping the clutch or brake by cycling it on and off for 30 to 40 cycles
3
4
5
6
7
EC / EB Series Electro Clutches and Brakes
EC / EB Series Electro Clutches and Brakes Shaft Mounted Clutches and Brakes Shaft Mounted Clutches EC Series All the features of an electric clutch in a convenient, preassembled package. Mounts on any
More informationAir Champ RPM DPC-15T DPC-13T DPC-11T DPC-11T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T
DUAL PLATE FRICTION CLUTCH SELECTION CHART Friction clutch recommendation is based upon air pressure of 50 psi, transmitted horsepower and speed. RPM 100 200 300 400 500 600 700 800 900 1000 1100 1200
More informationUM Series UniModule. Pre-assembled, C-face Clutches and Brakes. Original Design Sizes 210 & 215. GEN 2 Design Sizes 50, 100 & 180
re-assembled, C-face Clutches and Brakes UniModules offer the ultimate in Clutch/ Brake performance and convenience. UniModules offer the same performance as EM s without the assembly required. Completely
More informationCOMBIBOX. Program Schedule. Design. COMBIBOX clutch-brake-combination type 10 / 09 / 06. Attachments
clutch-brake-combination 10 / 09 / 06 with an energised to engage single sided clutch / brake... 10 with an energised to engage single sided clutch without brake... 09 with an energised to engage single
More informationTooth Clutches. Series 5H and 55H-P Pressure Applied Tooth Clutch. Stationary Cylinder for Dry Operation or in Oil. Series 5H and 55H-P
Series 5H and 55H-P Series 5H and 55H-P Pressure Applied Tooth Clutch Stationary Cylinder for Dry Operation or in Oil Features Tooth clutch gives positive drive with no slip Shielded bearings need no lubrication
More informationQ&A Friction Clutches & Brakes 101 Webinar - Basics for Design Engineers
Q&A Friction Clutches & Brakes 101 Webinar - Basics for Design Engineers Q: is it possible to modulate the braking torque of these electromagnetic friction and clutches or do they work on/off only? A:
More informationOVERLOAD CLUTCHES FOR INDEX DRIVES
The Driving Force in Automation OVERLOAD CLUTCHES FOR INDEX DRIVES WARNING WARNING This is a controlled document. It is your responsibility to deliver this information to the end user of the CAMCO indexer.
More informationTAKE IT TO THE NEXEN LEVEL
TAKE IT TO THE NEXEN LEVEL INDUSTRIES SERVED Aerospace Automation Equipment Automotive Bottling CNC Machining Commercial Laundry Equipment Converting Conveying Food Processing Machine Tool Material Handling
More informationAir Champ DPC-9T & DPC-11T Static Torque in Inch-Pounds. Air Pressure in PSI
CLUTCHES DPC SERIES DUAL PLATE CLUTCHES This Series, specified by component, allows you to custom design for specific application requirements: Static Torque capacity up to 36,000 In. Lbs. @ 80 psi Maximum
More informationCOMBIBOX Program Schedule. Design. COMBIBOX Clutch-brake-combination type 10 / 09 / 06. Attachments input
COMBIBOX Program Schedule COMBIBOX Clutch-brake-combination type 10 / 09 / 06 with an energised to engage single sided clutch / brake COMBIBOX 10 page 37 with an energised to engage single sided clutch
More informationThe Genuine Wrap Spring. CB Series sizes 2, 4, 5, 6, 7, 8, 10 Super CB Series sizes 5, 6, 7, 8, 10 SAC Series sizes 2, 4, 5, 6
CB-8 CB-6 The Genuine Wrap Spring CB Series sizes 2, 4, 5, 6, 7, 8, 10 Super CB Series sizes 5, 6, 7, 8, 10 SAC Series sizes 2, 4, 5, 6 Installation and Mounting Manual 06/2008 Keep all product manuals
More informationisaregisteredtrademarkofcustom Machine&ToolCo.,Inc.Copyright Custom Machine&ToolCo.,Inc.Alrightsreserved.
CMT isaregisteredtrademarkofcustom Machine&ToolCo.,Inc.Copyright 1998-2017Custom Machine&ToolCo.,Inc.Alrightsreserved. WHAT IS CONCENTRIC MAXI TORQUE? CMT is a revolutionary new keyless tapered bushing,
More informationInfinit-Indexer Phase Adjuster. HDI Series. Total Motion Control. Harmonic Drive gear
Infinit-Indexer Phase Adjuster HDI Series Total Motion Control Harmonic Drive gear P r e c i s i o n G e a r i n g a n d M o t i o n Control HDI Infinit-Indexer Phase Adjusters HDI s are shaft mounted
More informationFractional HP Clutches/Brakes. A-Track Linear Actuators
Fractional HP Clutches/Brakes A-Track Linear Actuators Page Pages 2 - Features Selection Guide Pages 4 - SF Series Pages 6-7 SFP Series SF Series clutches provide a bearing mounted clutch for use in parallel
More informationMagnetic Particle Brakes and Clutches
Magnetic Particle Brakes and Clutches Accurate torque control with instantaneous engagement! Available in a wide range of models and sizes Warner Electric s magnetic particle brakes and clutches are quiet
More informationELECTROMAGNETIC CLUTCH AND BRAKE UNITS
-ACTUATED CLUTCHES AND BRAKES CLUTCH AND BRAKE UNITS Application Printing machinery, bookbinding machinery, woodworking machinery, semiconductor manufacturing equipment Connection and Release, Required
More informationSF-120, SF-170, SF-250, SF-400 Bearing Mounted, Flange Mounted, SFC-120, SFC-170, SFC-250, SFC-400 Bearing Mounted, Flange Mounted
SF-120, SF-170, SF-250, SF-400 Bearing Mounted, Flange Mounted, SFC-120, SFC-170, SFC-250, SFC-400 Bearing Mounted, Flange Mounted P-0200-WE 819-0481 Installation Instructions An Altra Industrial Motion
More informationFeatures / Benefits... PT5-2
CONTENTS Features / Benefits................................................... PT5-2 PT Component Specification........................................................ PT5-3 How To Order.......................................................
More informationATC / ATB Series AT Clutches and Brakes
ATC / ATB Series AT Clutches and Brakes Rugged, Durable, Heavy Duty Clutches and Brakes Warner Electric s AT clutches and brakes are rugged and durable. The ATC and ATB incorporate a molded friction material/pole
More informationCombination Clutch/Brake Packages
Packaged CB Performance Series Clutch Products / Brakes Combination Clutch/Brake Packages CB Series clutch/brake combinations are designed for applications requiring a continuous rotational input being
More informationCOUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS
COUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS FLEXIBLE COUPLINGS HRC TYPE Hercus HRC Couplings are designed for general-purpose applications
More informationDr. TRETTER AG. Tolerance Rings. safe cost-effective fast assembly
Dr. TRETTER AG Tolerance Rings safe cost-effective fast assembly Tolerance Rings are corrugated metal strips manufactured of high quality spring steel. Tolerance Rings are a fastening device between two
More informationPOWERGRIP 5MGT & POLY CHAIN 5MGT SPROCKETS
Section 4 POWERGRIP 5MGT & POLY CHAIN 5MGT SPROCKETS Use with 5mm PowerGrip GT or Poly Chain GT belts. 2MGT and 3MGT pulleys available on request, please contact Gates customer service. Identification
More informationEM Series Electro Module
Individual lutch or Brake Module ombine to omprise a lutch, Brake or lutch/brake ombination Electro Modules are individual clutch or brake units which are assembled together to comprise a clutch, brake,
More informationATC / ATB Series AT Clutches and Brakes
ATC / ATB Series AT Clutches and Brakes Rugged, Durable, Heavy Duty Clutches and Brakes Warner Electric s AT clutches and brakes are rugged and durable. The ATC and ATB incorporate a molded friction material/pole
More informationEJP SERIES Right-angle Worm
EJP SERIES T he EJP series is ideal for demanding applications requiring high efficiency, torsional rigidity and zero backlash. It s lightweight, black anodized aluminum housing and dual input/output seals
More informationLocking Assemblies & Locking Elements
US 01 2016 Locking Assemblies & Locking Elements Partner for Performance www.ringfeder.com Welcome to your system supplier for every aspect of power transmission Today s RINGFEDER POWER TRANSMISSION GMBH
More informationPin-guided clutch with three flyweights
S-Type Pin-guided clutch with three flyweights Construction and mode of operation 2 5 4 3 3 1 1 5 2 6 4 = Hub = Flyweights = Cylindrical pin = Tension spring = Lining = Clutch drum / Cover disc Low noise
More informationEB Series Electro Brake
Shaft Mounted Brakes for Power-On Applications Pre-engineered, pre-packaged brakes mount on motor or thru shafts. They have been designed to mate easily with industry standard motors, reducers and other
More informationPRECISION BELLOWS COUPLINGS
PRECISION BELLOWS COUPLINGS Bellows couplings are used where precise rotation, high speeds, and dynamic motion must be transmitted. They exhibit zero backlash and a high level of torsional stiffness, offering
More informationHighest Precision: Dyna Series
GAM can. Just ask! If you don t see exactly what you need, let us know. We can modify the Dyna Series gearboxes to meet your needs. Page 3 provides a list of commonly requested modifications to give you
More informationSPECIFICATION HOW TO ORDER NOMENCLATURE. Fractional Hp Clutches & Brakes SPECIFICATION HOW TO ORDER NOMENCLATURE PT2--24
SPECIFICATION HOW TO ORDER NOMENCLATURE Fractional Hp Clutches & Brakes SPECIFICATION The Fractional product offerings include three shaft mounted clutches and three flange mounted brakes. In the shaft
More informationH1600 Mechanical Overload Clutches HOR Series
H1600 Mechanical Overload es HOR Series Section Contents FEATURES... 36 OPERATING PRINCIPLES... 36 SELECTION... 37 HOW TO ORER... 37 RATINGS AN IMENSIONS... 38 MOUNTING HOLE PATTERNS... 42 GENERAL INFORMATION...
More informationN S I D E T H I S G U I D E
GTC Manufacturing General Information and Installation Instructions, Release 3 February 2010 TC2 Torque Converter Asymmetrical System Superior Performance GTC Industries The TC2 is an asymmetrical torque
More informationApplication Note : Comparative Motor Technologies
Application Note : Comparative Motor Technologies Air Motor and Cylinders Air Actuators use compressed air to move a piston for linear motion or turn a turbine for rotary motion. Responsiveness, speed
More informationCOMBIBOX. Program Schedule. with an energised to engage single sided clutch without brake... COMBIBOX 09
COMBIBOX clutch-brake-combination 10 / 09 / 06 with an energised to engage single sided clutch / brake... COMBIBOX 10 with an energised to engage single sided clutch without brake... COMBIBOX 09 with an
More informationServing Industrial Markets Since 1961:
Full Line Brochure Clutches Brakes Clutch Brakes Caliper Brakes & Rotors Torque Limiters Air Shaft Seals Sheaves Serving Industrial Markets Since 1961: Food Processing & Packaging Material Handling Printing
More informationElectromagnetic tooth clutch Type 546
Electromagnetic tooth clutch Type 546 Characteristics and features high torque transfer despite compact dimensions positive-locking transmission of torque without slip engageable also at low relative speed
More informationElectromagnetic clutch-brake combinations INTORQ
Electromagnetic clutch-brake combinations INTORQ 14.800 14.867 7.5 120 Nm setting the standard 2 CBC en 5/2005 Contents Clutch-brake combinations Product information 4 Type code 6 Design selection 8 Overview
More informationPERFORMANCE THROUGH REVOLUTION
PERFORMANCE THROUGH REVOLUTION Dynamatic has a complete range of gear pumps for both mobile and industrial market segments. Dynamatic developed these pumps in technical collaboration with DOWTY Hydraulic
More informationTECHNICAL BULLETIN 98 MODEL EMA
TECHNICAL BULLETIN 98 MODEL EMA ELECTRIC MULTIPLE DISC CLUTCHES and BRAKES The Carlyle Johnson Machine Company, LLC 291 Boston Turnpike P.O. Box 9546 Bolton, CT 06043-9546 (860) 643-1531 Toll-free (888)
More informationClutch Coupling. PCC-500 Normal Duty HUB VIEW COLLECTOR RING VIEW. Customer Shall Maintain: Warner Electric ( )
Clutch Coupling PCC-00 Normal Duty See page 22 for.171.7 HUB VIEW.97 1/2-1 NPSM Am. std. straight pipe tap. 1.0 1. 1.0 See page 22 for details on Bushings..062 Min. running clearance..062 when new 1.17
More informationInstallation Instructions
Primary Clutch, Pin Drive Armature, Spline Drive Armature PC-825, PC-1000, PC-1225, PC-1525 Primary Clutch Coupling, Spline Drive Armature PCC-825, PCC-1000, PCC-1225, PCC-1525 P-206 819-0519 Installation
More informationSPH Series GAM CAN, JUST ASK!
SPH Series GAM CAN, JUST ASK! - Highest Precision Class The SPH is GAM s latest solution for today s demanding motion control challenges. Available in six frame sizes and nominal torque ratings ranging
More informationAltra Industrial Motion. AquaMaKKs Water Cooled Clutches and Brakes with Composite Water Jackets
Altra Industrial Motion AquaMaKKs Water Cooled Clutches and Brakes with Composite Water Jackets AquaMaKKs Water Cooled Clutches and Brakes AquaMaKKs water cooled clutches and brakes are designed to provide
More informationROLLER CHAIN SPROCKETS INDEX...E-1 E-2 MADE-TO-ORDER CAPABILITIES...E-3
Index SECTION E ROLLER CHAIN SPROCKETS PRODUCT PAGE INDEX...E-1 E-2 MADE-TO-ORDER CAPABILITIES...E-3 SECTION I STANDARD SPROCKETS...E-4 E-112 Shear Pin Sprockets, Bolt-On...E-4 E-6 Type D Sprockets, Detachable
More informationPrimary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225
Primary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225 P-205 819-0474 Installation Instructions Contents Installation Instructions
More informationAssortment 2013_FPT BOOK.indb /02/13 6:57 PM
Assortment Contents Why compete against your supplier when you can be our partner Chain Tensioners...14 see Chains section for details Anti-Vibration Mounts...224 Key Steel...225 Motor Rails...226 Self
More informationELECTROMAGNETIC-ACTUATED CLUTCHES & BRAKES
-ACTUATED -ACTUATED Clutch/brake 1 1 1 11/ odels (5 ~ 32) odels (2.4 ~ 1) 111 odels (5 ~ 32) odels (2.4 ~ 1) Application rinting machinery, bookbinding machinery, food machinery, wrapping machinery, textiles
More informationElectromagnetic clutches and brakes INTORQ and INTORQ
Electromagnetic clutches and brakes INTORQ 14.105 and INTORQ 14.115 7.5 480 Nm setting the standard Product information INTORQ electromagnetic clutches and brakes transmit the drive torque or braking torque
More informationAT Clutch Major Service Sizes 25, 55, 115
P-1404 819-0324 AT Clutch Major Service Sizes 25, 55, 115 Installation Instructions Contents Introduction............................ 2 Warranty....................... back cover Failure to follow these
More informationLINEAR MOTION CONTROL PRODUCTS
LINEAR MOTION CONTROL PRODUCTS Servomotor Brakes Eclipse Servomotor Brake The Eclipse Servomotor Brake family is a springengaged servomotor brakes equipped with a split hub, clamp collar for attachment
More informationE and VE Construction
E and VE Construction E Element VE Element Type E and VE elements combine rugged design and rigid construction features which make them ideal for moderate to heavy duty clutch and brake service. They are
More informationSection 15 Unit Selection Procedures
APC-2006 All Products Catalog Section 15 Unit Selection Procedures Main Office and Manufacturing Plant 3660 Dixie Highway Fairfield, Ohio 45014 Telephone: (513) 868-0900 Fax: (513) 868-2105 E-Mail: info@forcecontrol.com
More informationCurrent Controlled Electric Hysteresis Brakes Advantages The superior design of these hysteresis devices provides several inherent advantages over mag
Current Controlled Hysteresis Brakes Electrically controlled No wearing parts Infinitely adjustable for precise torque/ tension control TRANSMITTING TORQUE THROUGH AIR Current Controlled Electric Hysteresis
More informationHighest Performance: Dyna Series
Highest Performance: Dyna Series The Dyna Series is our highest performance right-angle gear reducer utilizing sophisticated hypoid gearing. The benefit of hypoid gearing is that it combines the space
More informationEB and ER Construction
EB and ER Construction EB Element EB elements are suited to slow speed applications having moderate starting and stopping loads. They are used as slip clutches and tension brakes for lighter torque and
More informationAdvanced Technology Tension Clutches
P-220 819-0339 Advanced Technology Tension Clutches Installation Instructions Contents Installation................................. 2 Clutch Repair On the Shaft.................. 4 Clutch Service Major.......................
More informationDriver Driven. InputSpeed. Gears
Gears Gears are toothed wheels designed to transmit rotary motion and power from one part of a mechanism to another. They are fitted to shafts with special devices called keys (or splines) that ensure
More informationmodel HP Servo AccuDrive Family of Products
model 09090.01 AccuDrive Family of Products Series W Model RG Series S Series P Series E/LE ACCUDRIVE PRECISION PRODUCTS Now you can get design flexibility and lasting performance from our complete family
More informationRFC SPECIALTY LOCKING DEVICES
RINGFEDER Products are available from MARYLAND METRICS P.O. Box 261 Owings Mills, MD 21117 USA email: sales@mdmetric.com web: http://mdmetric.com phones: (410)358-3130 (800)638-1830 faxes: (410)358-3142
More informationFOR MORE INFORMATION CALL CLARK ROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES...
Index SECTION E ROLLER CHAIN PRODUCT PAGE INDEX...E- - E-2 MADE-TO-ORDER CAPABILITIES...E- SECTION I STANDARD...E-4 - E-2 Shear Pin Sprockets, Bolt-On...E-4 - E-6 Type D Sprockets, Detachable s Split and
More informationTRADITIONAL SHAFT HUB CONNECTIONS
TABLE OF CONTENTS MAV locking devices.... Pg. 2 Traditional shaft hub connections...pg. 3 Advantages of MAV locking devices...pg. 4 The wedge principle..... Pg. 5 Installation removal...pg. 6 Characteristics....
More informationNow you can get design flexibility and lasting performance from our complete family of AccuDrive Precision Products.
ACCUDRIVE PRECISION PRODUCTS Now you can get design flexibility and lasting performance from our complete family of AccuDrive Precision Products. Series W Precision Servo Gearhead Output torque up to 8,500
More informationShaft-Hub-Connections
Stand: 14.01.2010 Shaft-Hub-Connections Shrink Discs Cone Clamping Elements Star Discs 36 Edition 2012/2013 RINGSPANN Eingetragenes Warenzeichen der RINGSPANN GmbH, Bad Homburg Table of Contents Introduction
More information6. Remove OEM bolts from engine at locations A, B, and C. Lay the wiring off to the side.
700359 DewEze Clutch Pump Kit #700359 Ford 5.4L, 6.8L w/ and w/o A/C AA mount 1999- INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Drain the radiator. 3. Remove the air cleaner assembly. 4. Remove
More informationThe controllableollable Torque Limiting Clutch for
The controllableollable Torque Limiting Clutch for Filling Machinery Printing Machinery Packaging Machinery Conveyors and Materials Handling Equipment pneumatic or electromagnetic clutch Controllable during
More informationPackaged Electromagnetic Clutches/Brakes
A L T R A I N D U S T R I A L M O T I O N Packaged Electromagnetic Clutches/Brakes Altra Industrial Motion Boston Gear Boston Gear is a global supplier of quality power transmission products to most major
More informationRotary-Linear Actuator HSE4 Hydraulic / 100 Bar
Rotary-Linear Actuator HSE4 Hydraulic / 100 Bar 4 Function and features K A1 G1 B1 G2 KM Y B2 RE A2 Z S2 A S1 W B KS [ Operation ] [ Operating pressure ] The Eckart rotary-linear actuator HSE4 is a combination
More informationMönninghoff electromagnetic tooth clutches
Mönninghoff electromagnetic tooth clutches High torque without slip in compact size Angular synchronisation of input to output possible Torque limiting and other special tooth options readily available
More informationLocking Assemblies & Locking Elements
US 12 2010 Locking Assemblies & Locking Elements Partner for performance www.ringfeder.com A Global Presence For You The RINGFEDER POWER TRANSMISSION GMBH was founded in 1922 in Krefeld, Germany to fabricate
More informationCOUNTER SHAFT NUT LOCKING PLATE 1 $ HOIST DRUM CLUTCH EYE BOLTS 1 $ LEFT DRUM CLUTCH THREADED PIN 2 $ 138.
1 2184 PULLEY FOR RADIATOR FAN 1 $ 326.25 2 2184 PULLEY FOR RADIATOR FAN 1 $ 326.25 3 3331 REAR DRUM BRAKE RETURN SPRING 5 $ 51.31 5 10285 LEFT REAR DRUM BRAKE AIR CAN REACH ROD ( LONG ROD ) 1 $ 85.12
More informationFlexible Couplings 44
Flexible Couplings 44 RINGSPANN Registered Trademark of RINGSPANN GmbH, Bad Homburg MTY (81) 83 54 10 18 Why RINGSPANN Flexible Couplings? No connection of shafts without clutches It is a well-known fact
More informationPSI Series Features: Trouble-free design for long life. Simple mechanical actuation
CROSSOVER DRIVES Wrap Spring Clutches Ideal for Overrunning, Start- Stop, and Single Revolution Applications The Crossover Drives clutches are the basic form of wrap spring clutch design. For start-stop
More informationHighest Precision: Dyna Series
Highest Precision: Dyna Series GAM can. Just ask! If you don t see exactly what you need, let us know. We can modify the Dyna Series gearboxes to meet your needs. Page 3 provides a list of commonly requested
More informationFriction Clutches & Brakes
Friction Clutches & Brakes Thomson - Linear Motion. Optimized. Often the ideal design solution is not about finding the fastest, sturdiest, most accurate or even the least expensive option. Rather, the
More informationVertical Linear Drive with Toothed Belt and Integrated Recirculating Ball Bearing Guide Series OSP-E..BV
Vertical Linear Drive with and Integrated Recirculating Ball Bearing Guide Series OSP-E..BV Overview...25-28 Technical Data...29-31 Dimensions...32-33 25 Features TOOTHED BELT DRIVE FOR VERTICAL MOVEMENTS
More informationLIGHTWEIGHT AND COMPACT. SERIES SL Nm. single-position multi-position. THE ultimate COUPLING from Nm
LIGHTWEIGHT AND COMPACT L SAFETY COUPLINGS TOQLIGHT SEIES SL 5 700 Nm THE ultimate COUPLING from 5 700 Nm SEIES SL DESIGN / FEATUES Extremely lightweight construction Up to 60 % weight reduction in comparison
More informationStromag Dessau. safety in motion PRODUCT CATALOGUE. NFF4F-LS Brake. for Slow-Running High Torque Drivelines, in harsh environment
Stromag Dessau safety in motion PRODUCT CATALOGUE NFF4F-LS Brake for Slow-Running High Torque Drivelines, in harsh environment ENGINEERING THAT MOVES THE WORLD Applications Holding brake variations with
More informationINVOLUTE TOOLING CORPORATION
MANUFACTURERS OF DRIVES AND TRANSMISSIONS OFFICE: 13, JORBAGH, NEW DELHI - 110 003, INDIA, TEL: +91(011)24621453 FAX: +91(011) 24603609 WORKS: PLOT-65, SEC-27C, FARIDABAD - 121 003. INDIA, TEL: +91(0129)
More informationReducing Backlash / Increasing Rigidity Jaw Coupling Precision Jaw Oldham Helical Beam Disc coupling
Precision Couplings A shaft coupling is a critical element in a robust and durable linear shaft drive. Misalignment of motor and drive shafts can cause loss of precision, noise and premature failure. By
More informationElectric cylinders CASM
Electric cylinders CASM 32-4-63 Contents Product description 4 Motors and gearboxes 6 Manuals 1 3D models 1 Linear unit 3 12 Linear unit 4 14 Linear unit 63 16 linear unit 18 Actuator 32 2 Actuator 4 32
More informationKINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING
KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Sub Code/Name: ME 1352 DESIGN OF TRANSMISSION SYSTEMS Year/Sem: III / VI UNIT-I (Design of transmission systems for flexible
More informationEdition Manual Chapter Page Workshop Manual, Stiga Park 5 Belts 11
2008-05-19 Workshop Manual, Stiga Park 5 Belts 11 Pro 20 1. Dismantle the belts A and B as described above. 2. Block up the rear frame and remove the right rear wheel. Clean carefully the insex hole in
More informationRIGHT ANGLE DRIVES TG Series
RIGHT ANGLE DRIVES TG Series Right Angle Fixed Index Drives TG Series The rotary index table transforms a constant input drive motion into an intermittent output drive motion. The intermittent drive motion
More informationH2000 Pneumatic Overload Clutches
H2000 neumatic Overload Clutches Section Contents FEATURES... 54 OERATING RINCILES... 54 SELECTION... 55 HOW TO ORDER... 55 RATINGS AND DIMENSIONS... 56 GENERAL INFORMATION... 61 TORQUE CURVES... 62-1500-BG
More informationSeries 1000 and Cutout
17.15.Remove the belt from the tractor. NOTE: There were a small number of tractors made using a CVT drive and a 2-speed (L-H-N-R) GT transaxle. The belt must pass over the center mounted gear selector
More informationalpha Value Line - NPS Sizing and Technical Data Efficient Flexible Reliable
alpha Value Line - NPS Sizing and Technical Data Efficient Flexible Reliable alpha Value Line NP NPS NPL NPT NPR Ratios 3-100 Torsional backlash [arcmin] 8 Output type Smooth output shaft Grooved output
More informationHydraulically actuated clutches and spring-applied brakes clutch/brake combined units
왎 Hydraulically actuated clutches and spring-applied brakes clutch/brake combined units Or tlinghaus Plates. Clutches. Brakes. Systems. Hydraulically actuated clutches and spring-applied brakes clutch/brake
More informationVertical Linear Drive with Toothed Belt and Integrated Recirculating Ball Bearing Guide Series OSP-E..BV
Vertical Linear Drive with and Integrated Recirculating Ball Bearing Guide Series OSP-E..BV Contents Description Page Overview 25-28 Technical Data 29-31 Dimensions 32-33 25 Parker Hannifin Corporation
More informationKTR Torque Limiters Overload Protection Systems
KT Torque Limiters Overload Protection Systems UFLEX - Friction Disk - Zero Backlash Ball Detent KT SI - Ball/oller Bearing Style KT SI Compact - Zero Backlash Ball Detent Catalog Contents (Metric) Page
More informationEclipse Servo Motor Brake Flange Mounted, Spring Engaged, Air Released Split Hub, Clamp Collar Sizes 2, 3, 4, and 5 ECLIPSE PRODUCTS
ECLIPSE PRODUCTS TM TECHNICAL DATA SHEET Eclipse Servo Motor Brake Flange Mounted, Spring Engaged, Air Released Split Hub, Clamp Collar Sizes, 3, 4, and 5 ECLIPSE TM SERVO MOTOR BRAKE The Eclipse Servo
More informationWrap Spring Clutches and Clutch/Brakes
A L T R A I N D U S T R I A L M O T I O N Wrap Spring Clutches and Clutch/Brakes Wrap Spring Product Line CB Series SCB Series WSC Series Clutch/Brake Package Each CB Series unit is a completely self-contained,
More informationMarine Engineering Exam Resource Review of Couplings
1. What are rigid couplings used for? Used to join drive shafts together. True alignment and rigidity are required. Example Drive shafts and production lines, bridge cranes, solid shaft that needs to be
More informationComparison Chart. extremely difficult. Finally, separated components can rarely be re-used.
JAN 2014 Traditional Connections Why Go Keyless Keyed Bushing Systems Both QD and Taper-Lock bushing and weld-on hub systems are popular component mounting technologies. Yet both are ultimately keyed connections
More informationROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES...E-3
Index SECTION E ROLLER CHAIN PRODUCT PAGE INDEX...E- - E-2 MADE-TO-ORDER CAPABILITIES...E- SECTION I STANDARD...E-4 - E-2 Shear Pin Sprockets, Bolt-On...E-4 - E-6 Type D Sprockets, Detachable Hubs Split
More informationAir Champ. Product Function & Selection Chart...54 Section Index...55
GENERAL INFORMATION Product escription Index...1 PROUCT NUMBER INEX Product Numbers Index...2-3 FAMILY OF PROUCTS Air Champ Features & Benefits...4 Air Champ Family of Products...5-9 CLUTCHES Product Function
More informationSelection Tool. on the Internet at in the section MÄDLER -Tools. Other sizes and designs on request. Connecting Shafts Page 766
Couplings Overview Friction Clutches Friction Clutches Type B Axial Arrangement Friction Clutches Type C Transversal Flexibility Sliding Hubs with Torsionally-Flexible Coupling Multi-Disk Friction Clutches
More informationDURST. Over 3 hr. per day and incl.
pump drive selection guide Max. Max Input Input Flywheel Ratio Pump Pump Centre Approx. HP* Torque Style# Housing Inc. OR Dec. Adaptors Distance Weight Model (kw) Lb.ft (nm) Size kg 1PD06 495 1040 P,S
More informationElectromagnetically actuated clutches and brakes
Electromagnetically actuated clutches and brakes General notes Dry-running/wet-running 4.03.00 Electrical circuits 4.03.00 Rectifier units 4.03.00 Coil connections 4.04.00 Spark quenching 4.04.00 Protection
More information