Maytag-75V Parts Manual

Size: px

Start display at page:

Download "Maytag-75V Parts Manual"

Byron Hudson
5 years ago
Views:

1 Maytag-75V Parts Manual For Internal Use Only RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE Maytag One Dependability Square Newton, Iowa (641) JCARRITA/mcronan Part No

2 Retain This Manual In A Safe Place For Future Reference This product embodies advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY properly licensed technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. POUR VOTRE SÉCURITÉ Ne pas entreposer ni utiliser d essence ni d autres vapeurs ou liquides inflammables à proximité de cet appareil ou de tout autre appareil. We have tried to make this manual as complete as possible and hope you will find it useful. Manufacturer reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models. Important For your convenience, log the following information: Maytag-75V DATE OF PURCHASE MODEL NO. DEALER S NAME Serial Number(s) For replacement parts, contact the dealer from which the dryer was purchased or contact: MAYTAG 403 West Fourth St. North Newton, Iowa (641) The illustrations on the following pages may not depict your particular dryer exactly. The illustrations are a composite of the various dryer models. Be sure to check the descriptions of the parts thoroughly before ordering. IMPORTANT NOTE TO PURCHASER Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer.

3 Table of Contents Control Door Assembly... 2 Phase 5 OPL Microprocessor Control Panel Assembly... 3 Phase 5 Coin Microprocessor Control Panel Assembly... 4 Dual Timer Tap Touch Controls... 5 Coin and OPL Control Box Assembly... 6 Coin Vault Assembly... 7 Front Panel Assembly... 8 Main Door Assembly... 9 Main Door Switch Basket (Tumbler)/Support Assemblies Lint Drawer/Lint Drawer Switch Assembly Idler Bearing Assembly Basket (Tumbler) Bearing Assembly... 14, 15 Non-Reversing T.E.F.C. Motor Mount Assembly... 16, 17 Reversing T.E.F.C. Motor Mount Assembly... 18, 19 Sensor Bracket Assemblies... 20, 21 Direct Spark Ignition (DSI) Burner Assembly... 22, 23 Electric Oven Assembly... 24, 25 Air Operated Steam Damper Assembly... 26, 27 Single-Phase (1ø) Motor, Electric Relay Panel Assembly Phase (3ø) Motor, Electric Relay Panel Assembly VAC 3-Phase (3ø) Motor, Electric Relay Panel Assembly Reversing Electric Relay Panel Assembly VAC Reversing Electric Relay Panel Assembly Sail Switch Assembly Outer Top/Back Guard Assemblies Electric Oven Component Application Chart Additional Parts Available... 36

4 2 Control Door Assembly High Security Lock Assembly (for coin models Only) XX4451 Key (for coin models Only) Special Dummy Lock ONLY (for non-coin models Only) Lock Cam ONLY * 1 Logo White Control Door Assembly with Black Trim (includes illus. nos. 4 through 7) Bisque Control Door with Black Trim (includes illus. nos. 4 through 7) Black Trim Strip with Lock Hole Sponge Tape (sold by the foot) /4-20 with 3/4 Free Spin Wash Nut #10-16 x 3/4 TORX + BTN Type Control Door Rod Support Catch Control Door Rod Retainer Clip Control Door Support Rod * Contact reseller for logo.

5 Phase 5 OPL Microprocessor Control Panel Assembly OPL English Keyboard (touch pad) Label Assembly Phase 5 Microprocessor Control Panel ONLY Phase 5 Microprocessor Control Panel ONLY with Battery Bracket Phase 5 OPL Non-Reversing Microprocessor Control Panel Assembly Complete (includes illus. nos. 1 through 5 and 7) Phase 5 OPL Reversing Microprocessor Control Panel Assembly Complete (includes illus. nos. 1 through 5 and 7) Phase 5 OPL Non-Reversing Microprocessor Controller (computer) ONLY Phase 5 OPL Reversing Microprocessor Controller (computer) ONLY Phase 5 Battery Clip #6 Star Washer #6-32 x 1/4 Phillips Round Head Machine Screw #10-16 x 1/2 Hex Head TEK Crimptite Screw /8-Amp (slo blo) Fuse IMPORTANT: Check label on computer chip to verify correct part number for controller (computer).

6 4 Phase 5 Coin Microprocessor Control Panel Assembly Coin Keyboard (touch pad) Label Assembly Phase 5 Coin Control Panel Assembly (includes illus. nos. 1, 2, 4 through 6, and 11) Coin Control Panel ONLY #10-16 x 1/2 Hex Head TEK Crimptite Screw Phase 5 Coin Microprocessor Controller (computer) ONLY Phase 5 Battery Clip #6 Star Washer #6-32 x 1/4 Phillips Round Head Machine Screw Coin Acceptor Optic Switch ONLY Optic Switch Connector ONLY Microprocessor Socket ONLY Single Coin Optical Switch Harness Microprocessor (female) Pin Extraction Tool /8-Amp (slo blo) Fuse IMPORTANT: Check label on computer chip to verify correct part number of controller (computer).

7 Dual Timer Tap Touch Controls Minute Timer - 24 VAC Minute Timer - 24 VAC Red Pilot Light - 24 VAC Tap Touch Switch Relay SPST 24v Position Terminal Block #6-32 Pal Nut Dual Timer Panel Complete (includes illus. nos. 1 through 15) Dual Timer Panel ONLY #6 Star Washer #6-32 Hex Nut #10-24 x 1/2 Phillips Pan Head Machine Screw #8-32 x 1/4 Phillips Round Head Machine Screw Dual Timer Panel Overlay Pure Touch Knob with Red Pointer Pure Touch Knob with Blue Pointer

8 6 Coin and OPL Control Box Assembly Pin Microprocessor (computer) Connector * Socket Terminal ONLY #8-18 x 7/16 Phillips Pan Head TEK Screw Reversing Timer Pin/Socket Extraction Tool * As required.

9 Coin Vault Assembly Microprocessor Coin Vault Assembly Complete (includes illus. nos. 1 through 6) Microprocessor Coin Vault ONLY Cam for 1/4 Turn Lock ONLY /4 Turn Lock with Key and Cam * 1 1/4 Turn Mer-Pel Key ONLY /4 Turn Coin Box Assembly (includes illus. nos. 2 through 5) /4 Turn Coin Box ONLY without Faceplate High Security (Greenwald) Coin Box ONLY with Key /4 Turn Coin Box Faceplate ONLY /4-20 Free Spin Wash Nut Control Door Support Rod Control Door Rod Retainer Clip Control Door Rod Support Catch * Specify key number when ordering.

10 8 Front Panel Assembly White Front Panel Assembly (includes illus. nos. 1, 3, and 5 through 8) Bisque Right Hand Front Panel Assembly (includes illus. nos. 1, 3, and 5 through 8) #10-16 x 1/2 Hex Head TEK Crimptite Screw Rubber Grommet Lint Drawer Switch (refer to Lint Drawer/Lint Drawer Switch Assembly on page 12) Friction Door Latch /32 Pop Rivet Black Front Panel Trim Assembly /4-20 Serrated Hex Flange Nut

11 Main Door Assembly Stamped Steel Main Door Handle Main Door Glass Black Glass Adhesive (10.3 oz. cartridge) Small Door Extruded Gasket /4-20 Free Spin Washnut /2 Cold Rolled Steel (CRS) Main Door Hinge Assembly # Door Latch Screw #10-32 Black Hex Acorn Locknut Formed Black Main Door Assembly with Hinge

12 10 Main Door Switch #6-32 Hex Nut #6 Lock Washer Single Pole Door Switch Insulated Female Terminal /8 Standard Nylon Spacer /2 Cold Rolled Steel (CRS) Main Door Hinge Assembly (includes illus. nos. 6 and 7) #6-32 x 1 Self-Clinching Stud Main Door Switch Housing #10-32 x 1/4 Phillips Pan Head Screw Rubber Grommet

13 Basket (Tumbler)/Support Assemblies 11 1* Basket (tumbler) ONLY without Felt Collar Basket (tumbler) and Support Assembly Complete (includes illus. nos. 1 through 10) #10-16 x 1/2 TORX Head Crimptite Screw TORX Hand Driver (for removal of TORX head screw) Basket (tumbler) Rib ONLY /16-18 x 3/4 Socket Button Head Screw /8-16 x 37 Tie Rod /8 Flat Washer Basket (tumbler) Support ONLY /4 x 1/4 x 1-1/4 Basket (tumbler) Support Key /8-16 Hex Nut /8 Lock Washer /8 Flat Washer Felt Collar ONLY #847 Adhesive for Felt Collar * Felt collar is not included and must be ordered separately.

14 12 Lint Drawer/Lint Drawer Switch Assembly White Lint Drawer Assembly (includes illus. nos. 1 and 2) Bisque Lint Drawer Assembly (includes illus. nos. 1 and 2) Gasket (sold by the foot) Lint Drawer Switch Pin Socket Connector ONLY Socket Terminal ONLY Pin/Socket Extraction Tool Lint Drawer Switch Box Assembly (includes illus. nos. 3 through 6) Lint Drawer Switch Box Cover #8-18 x 7/16 Phillips Pan Head TEK Screw Pin Terminal ONLY Pin Connector ONLY

15 Idler Bearing Assembly L-680 V-Belt (basket [tumbler] to idler) For Both Reversing and Non-Reversing Models x 3 Compound Pulley L-720 V-Belt (idler to motor) For Non-Reversing Models ONLY L-650 V-Belt (idler to motor) For Reversing Models ONLY /16-18 x 1 Allen Setscrew /16 x 3/16 x 1-3/8 Key Idler Bearing Assembly Complete (includes illus. nos. 5 through 12) /8-16 x 1 Hex Head Machine Bolt /8 Lock Washer /8 Flat Washer Idler Square Washer /16-18 Hex Nut /16-18 x 3 Hex Head Machine Bolt

16 14 Basket (Tumbler) Bearing Assembly

17 Basket (Tumbler) Bearing Assembly /4 Flange Bearing /16 Lock Washer /16-12 Hex Nut Pillow Block Bearing Assembly Complete (includes illus. nos. 4 through 17, 23 and 24) Pillow Block Bearing Assembly Complete with Rotational Sensor (includes illus. nos. 4 through 18, 23 and 24) Pillow Block Bearing Platform ONLY Pillow Block Bearing Platform ONLY (for models with optional rotation sensor) /8 Pillow Block Bearing /8 Pillow Block Bearing (for models with optional rotation sensor) /8-16 x 2 Hex Bolt /8 Flat Washer /8 Flat Washer /8 Lock Washer /8-16 Hex Nut /16-24 x 3/8 Setscrew /16-18 Hex Nut /16-18 x 1-1/2 Tap Bolt /16 Lock Washer /8 Flat Washer /16-18 x 3/4 Tap Bolt Sintered 8 Magnet (for models with optional rotation sensor) Rotational Sensor Assembly Shaft Key (for reversing models Only) Pulley (for non-reversing models Only) /4 Pulley (for reversing models Only) Taper Lock Bushing (for reversing models Only) L-680 V-Belt (basket [tumbler] to idler) /16-18 x 1-1/2 Allen Setscrew /16-18 Hex Nut

18 16 Non-Reversing T.E.F.C. Motor Mount Assembly

19 Non-Reversing T.E.F.C. Motor Mount Assembly L-720 V-Belt (idler to motor) /16 x 3/16 x 1 Key /8 x 2-1/4 Motor Pulley (60 Hz Only) /16-18 x 3/4 Tap Bolt /16 Lock Washer /16 Flat Washer /4 HP 120/208/230v 1ø 60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor with Plug (56Z frame) Socket Terminal ONLY Pin/Socket Extraction Tool Pin Housing Connector /16-18 Hex Nut /16 Lock Washer /16 Flat Washer Neoprene Sponge Tape (sold by the foot) /16-18 Tinnerman Nut Non-Reversing Motor Mount ONLY (56Z frame) * 1 3/4 HP 120/230v 1ø 60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor Mount Assembly with Plug Complete (includes illus. nos. 2 through 7 and 13 through 20) HP 208/460v 60 Hz 3ø Motor Mount Assembly (includes illus. nos. 2 through 6 and 13 through 22) /4 S.A.E. Flat Washer /2 Impellor (1/2 bore) /16 x 3/16 x 1-7/8 Key /2 S.A.E. Flat Washer /2-20 Left Hand Jam Nut /8 x 90 Connector HP 208/460v 60 Hz 380v 50 Hz 3ø Motor * Specify voltage when ordering.

20 18 Reversing T.E.F.C. Motor Mount Assembly

21 Reversing T.E.F.C. Motor Mount Assembly L-650 V-Belt (to idler assembly) /16 x 3/16 x 1 Key /8 x 2-1/4 Motor Pulley (60 Hz Only) /8 x 90 Connector /2 HP 208/230/380/460v 3ø 50/60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor (56Z frame) /16-18 x 3/4 Tap Bolt /16 Lock Washer /16 Flat Washer 9* /2 HP 220/230/380/460v 3ø 50/60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor with 3/4 Shaft (56Z frame) /8 x 90 Connector /16-18 x 3/4 Tap Bolt /16 Lock Washer /16 Flat Washer /16-18 Tinnerman Nut /16-18 Hex Nut /16 Lock Washer /16 Flat Washer Reversing Motor Mount ONLY (56Z frame) ** 1 60 Hz Reversing Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor Mount Assembly Complete (includes illus. nos. 2 through 14 and 18 through 24) Neoprene Sponge Tape (sold by the foot) /4 S.A.E. Flat Washer /16 x 3/16 x 1-7/8 Key /2 Impellor (1/2 bore) *** 1/2 S.A.E. Flat Washer /2-20 Left Hand Jam Nut * Check part number on motor data label to verify correct motor. ** Specify voltage when ordering. *** As required.

22 20 Sensor Bracket Assemblies

23 Sensor Bracket Assemblies /4 Temperature Sensor Probe Assembly (includes illus. nos. 1 and 5 through 8) Automatic Reset Thermostat #6 Star Washer #6-32 Hex Nut Insulated Female Terminal Socket Terminal ONLY Pin/Socket Extraction Tool Pin Socket Connector ONLY /4 Tinnerman Push On Fastener #6-32 x 1/4 Phillips Round Head Machine Screw Microprocessor Sensor Bracket Assembly Complete (includes illus. nos. 1 through 10) Universal Sensor Bracket ONLY Pin Connector ONLY Pin Terminal ONLY #8-18 x 7/16 Phillips Pan Head TEK Screw #6-32 x 1/4 Phillips Round Head Machine Screw Large Thermostat Large Thermostat Automatic Reset Thermostat Large Thermostat #6 Star Washer #6-32 Hex Nut Sensor Jumper ONLY Insulated Female Terminal Socket Terminal ONLY Pin Socket Connector ONLY Sensor Bracket Harness Assembly (includes illus. nos. 22, 23, and 24) Noncomputer Sensor Bracket Assembly Complete - Includes Thermostats (includes illus. nos. 14 through 25) Universal Sensor Bracket ONLY Pin Connector ONLY Pin Terminal ONLY Pin/Socket Extraction Tool #8-18 x 7/16 Phillips Pan Head TEK Screw

24 22 Direct Spark Ignition (DSI) Burner Assembly 1* Natural Gas Burner Assembly Complete (includes illus. nos. 1 through 5, and 7 through 31) For Models Mfd. with Natural Gas ONLY Liquid Propane (L.P.) Gas Burner Assembly Complete (includes illus. nos. 1 through 5, and 7 through 31) For Models Mfd. with Liquid Propane (L.P.) Gas ONLY Burner Box ONLY Large Burner Tube /4 Direct Spark Ignition (DSI) Manifold (4-port) Bracket for Horizontal Facing Gas Valve /2 24 VAC Redundant (natural gas) Gas Valve /2 24 VAC Direct Spark Ignition (DSI) Liquid Propane (L.P.) Gas Valve Assembly Maytag 75V Liquid Propane (L.P.) Conversion Kit 6* #30 Burner Orifice (natural gas) ONLY #49 Burner Orifice (liquid propane [L.P.] gas) ONLY

25 Direct Spark Ignition (DSI) Burner Assembly (continued) #8-32 x 1/2 Pan Head Machine Screw #8-32 Pal Nut #10-16 x 1/2 Hex Washer TEK Screw Ignitor Probe Assembly with 19 Leads #10-16 x 1/2 Hex Head TEK Crimptite Screw #6-32 Hex Nut Direct Spark Ignition (DSI) Module with Three (3) Tries Johnson Controls Direct Spark Ignition (DSI) Module Mounting Bracket /2 x 1-1/2 Long Black Nipple /2 Street Elbow /2 Black Union /2 x 29-1/8 Nipple Hi-Limit Mounting Bracket #6-32 Pal Nut #6-32 x 1/2 Phillips Round Head Machine Screw º Hi-Limit Manual Reset Pipe Bracket (bent) /4 to 1/2 Reducing Coupling Twin Speed Nut Sail Switch Box Cover and Bracket ONLY (refer to Sail Switch Assembly on page 33) Sail Switch ONLY #4 x 3/4 Pan Head A Machine Screw Sail Switch Actuator Rod Sail Switch Damper (flat) /8 Push On Fastener ** Steam to Gas Interface Plate...Not Illustrated * Consult factory for elevations over 2,000 feet. ** Needed when converting from steam to gas heat.

26 24 Electric Oven Assembly ELECTRIC OVEN (REAR VIEW)

27 Electric Oven Assembly Large Electric Oven Box ONLY * 1 Electric Oven Assembly Complete * - Electric Element #10-16 x 1/2 Hex Washer TEK Screw Sail Switch Box with Bracket and Cover ONLY Sail Switch Box Assembly Complete (includes illus. nos. 4 through 12) Twin Speed Nut #10-16 x 1/2 Hex Head TEK Crimptite Screw Sail Switch Box Cover and Bracket ONLY (refer to Sail Switch Assembly on page 33) Sail Switch ONLY #4 x 3/4 Pan Head A Machine Screw Sail Switch Actuator Rod Sail Switch Damper (flat) /8 Push On Fastener #10-16 x 1/2 Hex Washer TEK Screw Electric Oven Front Cover ONLY Large Relay Box Cover ONLY #10-24 x 5/8 Slotted Truss Head Machine Screw º Hi-Limit #10-16 x 1/2 Hex Washer TEK Screw #10-24 Speed Nut Terminal Lug for Wire /4-20 Free Spin Wash Nut * 1 Oven Relay * 1 Oven Relay Replacement Coil Internal Ceramic Insulator (2 per element) External Ceramic Insulator (2 per element) #10-32 Hex Nut (4 per element) * - Bus Bar (sold by the foot) * - Terminal Lug #10 Star Washer (2 per element) Large Electric Oven Right Side Cover ONLY #10-24 x 5/8 Slotted Truss Head Machine Screw * Refer to Electric Oven Component Application Chart on page 35.

28 26 Air Operated Steam Damper Assembly

29 Air Operated Steam Damper Assembly Steam Coil Assembly /16 Lock Washer /16-18 Hex Nut /4-20 Hex Nut /4 Lock Washer Steam Damper Hinge Assembly Steam Damper Assembly (includes illus. nos. 7, 10, and 11) /4 Lock Washer /4-20 Hex Nut Steam Damper Gasket (sold by the inch) Steam Damper Foam (68-1/2 length) /16-20 Stainless Steel Acorn Nut /16-20 Hex Nut /4 Bore x 3 Stroke Piston Piston Support Bracket /4-20 Hex Nut /4 Lock Washer /4 x 1/8 Connector /4 Tubing (sold by the foot) /4 x 1/8 Connector /8 Needle Valve /8 Close Nipple Way Micro Valve - 24 VAC #6-32 x 1 Phillips Round Head Machine Screw #6 Star Washer #6-32 Hex Nut Micro Valve Support Bracket /4-20 Hex Nut /4 Lock Washer /8 N.P.T. Silencer (muffler)

30 28 Single-Phase (1Ø) Motor, Electric Relay Panel Assembly #6-32 Pal Nut #10-16 x 1/2 Hex Washer TEK Screw #6-32 x 1-1/4 Phillips Pan Head Machine Screw Position Terminal Block Rear Electric Mounting Plate ONLY Rear Electric Panel Assembly Complete Volt (includes illus. nos. 1 through 14) Rear Electric Panel Wiring (120 volt Only)...Not Illustrated Rear Electric Panel Assembly Complete Volt (includes illus. nos. 1 through 14) Rear Electric Panel Wiring ( volt Only)...Not Illustrated Transformer Assembly Volt Transformer Assembly Volt or 2 Fuse Holder ONLY /4-Amp (slo blo) Fuse ONLY Volt /2-Amp (slo blo) Fuse ONLY Volt #8-18 x 7/16 Phillips Pan Head TEK Screw #10 x 1/2 Hex Washer TEK Screw (green) /16-18 Hex Nut L-70 Ground Lug /16 Lock Washer Pole Contactor Open/Closed Bushing

31 3-Phase (3Ø) Motor, Electric Relay Panel Assembly #6-32 Pal Nut #10-16 x 1/2 Hex Washer TEK Screw #6-32 x 1-1/4 Phillips Pan Head Machine Screw Position Terminal Block Rear Electric Mounting Plate ONLY Rear Electric Panel Assembly Complete Volt (includes illus. nos. 1 through 14) For Gas and Steam Heated Models ONLY Rear Electric Panel Assembly Complete Volt (includes illus. nos. 1 through 14) For Electric Heated Models ONLY Transformer Assembly Volt For Gas and Steam Heated Models ONLY Transformer Assembly Volt (for electric heated models Only) Fuse Holder ONLY /2-Amp (slo blo) Fuse ONLY #8-18 x 7/16 Phillips Pan Head TEK Screw #10 x 1/2 Hex Washer TEK Screw (green) /16-18 Hex Nut L-70 Ground Lug /16 Lock Washer Pole Contactor Open/Closed Bushing

32 VAC 3-Phase (3Ø) Motor, Electric Relay Panel Assembly #6-32 x 1-1/2 Phillips Pan Head Machine Screw Position Terminal Block Transformer Assembly (460 VAC) for Micro Models ONLY Transformer Assembly (460 VAC) for Non-Micro Models ONLY Amp Double-Pole Circuit Breaker (460 VAC Only) x 15mm Din Rail #8-18 x 7/16 Phillips Pan Head TEK Screw #10 x 1/2 Ground Screw /16-18 Hex Nut L-70 Ground Lug /16 Lock Washer VAC 3-Pole Contactor Mounting Plate ONLY Rear Panel Assembly Complete (460 VAC) for Micro Models ONLY (includes illus. nos. 1 through 14) Rear Panel Assembly Complete (460 VAC) for Non-Micro Models ONLY (includes illus. nos. 1 through 14) #6-32 Pal Nut End Stop Open/Closed Bushing Control Voltage Transformer (24V) for Micro Models ONLY

33 Reversing Electric Relay Panel Assembly #10-16 x 1/2 Hex Washer TEK Screw #6-32 x 1-1/4 Phillips Pan Head Machine Screw Position Terminal Block Pole Reversing Contactor Transformer Assembly Volt For Gas and Steam Heated Models ONLY Transformer Assembly Volt (for electric heated models Only) Fuse Holder ONLY /2-Amp (slo blo) Fuse ONLY #8-18 x 7/16 Phillips Pan Head TEK Screw #10 x 1/2 Hex Washer TEK Screw (green) /16-18 Hex Nut L-70 Ground Lug /16 Lock Washer Pole Contactor Rear Electric Mounting Plate ONLY Rear Electric Panel Assembly Complete Volt (includes illus. nos. 1 through 15) For Gas and Steam Heated Models ONLY * 1 Rear Electric Panel Assembly Complete Volt For Electric Heated Models ONLY (includes illus. nos. 1 through 15) #6-32 Pal Nut Standard End Bracket * Not available at time of printing. Contact factory for additional information.

34 VAC Reversing Electric Relay Panel Assembly VAC Reversing Contactor #10 x 1/2 Hex Head TEK Screw (green) L-70 Ground Lug /16-18 Hex Nut /16 Lock Washer VAC 3-Pole Blower Contactor #10-16 x 1/2 Hex Washer TEK Screw Transformer Assembly (460 VAC) for Micro Models ONLY Transformer Assembly (460 VAC) for Non-Micro Models ONLY End Stop Mounting Plate ONLY VAC Reversing Rear Electrical Panel Assembly Complete For Micro Models ONLY (includes illus. nos. 1 through 16) * VAC Reversing Rear Electric Panel Assembly Complete For Non-Micro Models ONLY (includes illus. nos. 1 through 16) #6-32 Pal Nut #6-32 x 1-1/2 Phillips Pan Head Machine Screw Position Terminal Block Amp Double-Pole Circuit Breaker x 15mm Din Rail (sold by the inch) Phase (3ø) Power Input Label Open/Closed Bushing Control Voltage Transformer (24V) for Micro Models ONLY * Not available at time of printing. Contact factory for additional information.

35 Sail Switch Assembly Sail Switch Mounting Bracket Sail Switch Damper (flat) Sail Switch Box Cover Sail Switch Box Twin Speed Nut /8 Push On Fastener #10-16 x 1/2 Hex Head TEK Crimptite Screw #4 x 3/4 Pan Head A Machine Screw Sail Switch ONLY Sail Switch Box Assembly Complete (includes illus. nos. 1 through 10) Sail Switch Actuator Rod

36 34 Outer Top/Back Guard Assemblies Back Electrical Box Cover #8-18 x 7/16 Phillips Pan Head TEK Screw 3* Top Back Guard (for gas models Only) Top Back Guard (for electric models Only) #8-18 x 7/16 Phillips Pan Head TEK Screw #10-16 x 1/2 Hex Washer TEK Screw 6* Outer Top Bottom Back Guard #8-18 x 7/16 Phillips Pan Head TEK Screw Leveling Leg * There is no outer top or top back guard on steam models.

37 Electric Oven Component Application Chart 35 Kw Volt Phase Wire Oven Assembly* Part No. Elements Oven Wire Terminal Lug Oven Relay Bus Bar P/N Qty. S ize P art No. Qty. S ize P art No. Q ty. P art No. C at. No. Part No ø 3 or # DPA ø # DPA /480 3ø 3 or # DPA ø 3 or # DPA ø # DPA /480 3ø 3 or # DPA * When ordering oven assembly complete, specify 3 wire or 4 wire when applicable, as well as if dryer has microprocessor or non-microprocessor controls. N/A = Not available.

38 36 Additional Parts Available Part No. Description Clean Lint Screen Label CAUTION - Exhaust/Lint Screen Label Phase 5 OPL Program Location Summary Label WARNING - Fire Hazards Label MOP HEAD WARNING Label Aluminum Duct Tape (sold by the foot) /8 Straight (BX) Connector /8 x 45 (BX) Connector /8 Red Jacket (BX) Insulator /8 Jiffy Clip (BX) Retainer Clip /8 Greenfield (BX) /4 In-Line Connector Red Butt Connector #74B Wire Nut Closed End Connector /4 Insulated (female) Terminal /2 Wire Tie Harness Tie Harness Tie Mounting Clip Manometer (hydro gauge) for Measuring Gas Pressure White Brush-In-Cap Bottle Touch-Up Paint Tumbler Puller Assembly

39 Notes 37

40 Maytag /19/05-0

D-3030 Parts Manual. J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: / Fax:

D-3030 Parts Manual. J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: / Fax: D-3030 Parts Manual J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: 1 422 822282 / Fax: 1 422 824390 091802JCARRITA/wmarelli ADC Part No. 450215 Retain This Manual