RIGHT SIDE BROOM KIT

Size: px

Start display at page:

Download "RIGHT SIDE BROOM KIT"

Coleen Morgan
5 years ago
Views:

1 56306 RIGHT SIDE BROOM KIT For Advenger 2400C, 2600C, 280C, 320C / BR 600CS, 650CS, 700CS, 800CS Adgressor 2820C, 3220C, 3520C, 3820C / BR 850CS, 950CS, 050CS AquaRide SE / BRX 700 CONTENTS OF KIT ITEM PART NO. QTY DESCRIPTION Instruction Sheet Wsh, Flt SAE 5/ Scr, Pan Phil 0-24 x.50 NOTE Scr, Pan Phil /4-20 x Wsh, Flt SAE /4 NOTE Scr, Soc Set Loc /4-20 x.50 NOTE Scr, Hex Hd /4-20 x.75 NOTE Scr, Hex Hd 5/6-8 x Nut, Hex Nyl Loc 5/ Nut, Hex Nyl Loc 3/8-6 NOTE 0# Scr-Hex Hd Loc /4-20 x.50 NOTE Nut, Hex Nyl Loc M Nut, Hex Nyl Loc M Scr, Hex M8-. x 30mm Scr, Hex M-.75 x 30mm Nut, Wing SS 3/8-6 NOTE Bearing, Flange Bushing ITEM PART NO. QTY DESCRIPTION Nut Plate NOTE Switch, Waterproof NOTE Knob NOTE Brush Holder Weldment NOTE Sidebroom Arm Weldment NOTE Pivot Weldment Bracket Weldment 5690 Bracket, Lift Bar, Lift NOTE Rod, Lift NOTE Motor Assy 24V NOTE Brush, Sidebroom NOTE Harness, Sidebroom Wire Tie Pivot Weldment NOTE Bar Lift Weldment NOTE Wsh-Flt SS.320 x.500 x.5 # = Revised or new since last update INSTALLATION INSTRUCTIONS NOTE = These items are pre-assembled together to create the Lift Bar Assembly (D). NOTE 2 = These items are pre-assembled together to create the Broom/Motor Assembly (A). NOTE 3 = These two items are only used on models with a 35 & 38 size deck (BR 950/050). WARNING! DISCONNECT BATTERIES BEFORE SERVICING. See Figure. Mount the Bracket Weldment (24) to the machine s chassis using four of the Screws (3), Washers () and Nuts (). 2 Install the Pivot Weldment [(23) for models or (32) for use on 35 & 38 models] on top of the bracket weldment with the two remaining Screws (3), Washers () and Nuts (), according to Figure 2 based upon which model you have. 3 Attach the Broom/Motor Assembly (A) to the Pivot Weldment (23 or 32) using Screw (7), two Bushings (7), two Bearings (6) and Nut (8). 4 See Figure. Identify which type of throttle pedal you have, old style (metal) or new style (roto-molded) and follow the appropriate step below. Old Style Foot Pedal - Remove the front four Screws (B) which secure the Throttle Pedal (C) to the floor of the operator s compartment, these screws can be discarded. New Style Foot Pedal - Remove the front four Screws (AA) which secure the Foot Pedal Assembly (AB) to the floor of the operator s compartment, these screws can be discarded. Remove and save the rear Screw (AC) models: Slide the Lift Bar Assembly (D) down through the slot in the Lift Bracket (). Maneuver the bar assembly down until the long portion of the bar is in the slot. 35 & 38 models: - For 35 & 38 models only, the Lift Bar (33) will need to be used in place of item (26) in the Lift Bar Assembly (D). Disassemble the Lift Bar Assembly (D). Feed the Lift Bar (33) up through the slot in the Lift Bracket (). Reassemble the parts from the Lift Bar Assembly on to the Lift Bar (33) (exploded view shown in Figure 5). 206 Nilfisk, Inc. (page of 5)

2 6 Old Style Foot Pedal - Place the Lift Bracket () onto the throttle pedal and use the four new Screws (3) to mount the Lift Bracket and throttle pedal into place. New Style Foot Pedal Place the Lift Bracket () onto the floor of the operator s compartment. Use Washer () as a spacer under the rear of the Foot Pedal Assembly (AB) and mount the foot pedal assembly and lift bracket to the machine using the four new Screws (3). Use the saved screw (AC) from step 4 to secure the rear of the foot pedal assembly and washer. Old style foot pedal FIGURE AB AC New style foot pedal B AA C FRONT 33 D A C (page 2 of 5)

3 7 Connect the Lift Bar to the appropriate tab (use Figure 2 as a guide) on the top of the Broom/Motor Assembly (A) using Screw (4), Bushing (6) and Nut (). FIGURE 2 (page 3 of 5)

4 FIGURE 3 8 If the Side broom Harness (30) is not already plugged into the side broom switch and motor, connect them. See Figure 3 for connection information. Mount the fuse holder to the open hole in the side of the cover weldment using Wire Tie (3). 9 Locate the wire harness underneath the chassis (BLU & BLK wires) and connect to the side broom s Wiring Harness (30). FIGURE 4 0 Reconnect the batteries and test for proper operation. Side broom should run when the machine is scrubbing and the side broom is lowered. If the broom does not start and stop when it should, check the adjustment of the switch (shown in Figure 4). Height Adjustment As the bristles on the side broom wear down the broom will need to be lowered. To allow the broom to drop down farther simply loosen the Wing- Nut (5) and turn Nut (9) towards the end of the handle. Then tighten the wing-nut. Readjust the height when installing a new side broom. (page 4 of 5)

5 FIGURE (page 5 of 5)

WARNING! DISCONNECT BATTERIES BEFORE SERVICING. DRAIN THE SOLUTION SYSTEM PRIOR TO INSTALLATION.

WARNING! DISCONNECT BATTERIES BEFORE SERVICING. DRAIN THE SOLUTION SYSTEM PRIOR TO INSTALLATION. 56314308 SCRUB-N-VAC TOOL KIT For Advenger / BR 600S series Adgressor / BR 850S series AquaRide SE-AXP / BRX 700 X Adhancer R28-C, R32-C CONTENTS OF KIT ITEM PART NO. QTY DESCRIPTION 56040783 1 Instruction