USEFUL ACCESSORIES FOR LAB, EDUCATION AND WORKSHOP

Transcription

1 USEFUL ACCESSORIES FOR LAB, EDUCATION AND WORKSHOP CHAPTER 13: ACCESSORIES 450 Swivel Chair Standard and ESD, Workshop Chair, Stand-Up Seat and Class Room Chair 458 Pin Board / Room Partition 461 PROFI LED Workstation 464 Workspace Lamp 465 Magnifier Lamp 467 Table Lamp 468 TFT Swivel Arm 473 Power Outlet Strip 475 Laboratory Test Leads 476 Cord Holder and Plug Connector 478 Rubber Mat and ESD Rubber Mat 480 ESD Accessory 482 Holder for Perforated Backplanes 483 Small Part Magazine and Rotary Tower 484 Storage Bin, Transport Box and Sliding Nuts 485 Vice for Electronics 486 Vice for Mechanics 487 Soldering Fume Extraction 490 Protective Test Hood and Test Cabin 13 technical details are subject to change

2 INDUSTRY SWIVEL CHAIR TEC Characteristic for the TEC-Series is the tapering backrest, for a maximum of shoulder and arm mobility. Optionally the backrest could be equiped with handles, so there is no need to touch the upholstery with dirty hands. This series is DIN conform and holds the GS symbol. Seat: Base: Backrest: Casters: 49 x 36 x 45 64cm (WxDxH). Ø 70cm. 44 x 55-62cm (WxH). Soft, for hard floors. Standard or ESD: ESD version is with conductive seat and backrest, conductive casters and polished aluminium base. The chairs are according to DIN EN :2001 for disipation of static charge. Counter Version: Higher gas lift for a seating height of 59 84cm. Height adjustable chromed foot ring with anti-slip surface and base with glides. Note: For safety reason the counter version is not available with casters. standard: soft casters for hard floors, optionally: hard casters for soft floors, e.g. carpet Industry Swivel Chair TEC (xxx: colour code) xxx Industry Chair TEC with BP-Mechanics xxx Industry Chair TEC with ST-Mechanics xxx Industry Chair TEC with AS-Mechanics xxx ESD Industry Chair TEC with AS-Mechanics Surcharge for Backrest Handles (not available in ESD) Surcharge Counter Version (Standard and ESD) Surcharge for Polished Aluminium Base (Ø 70cm) Multidirectional Arm Rests for TEC ESD Multidirectional Arm Rests for TEC Option: Hard Casters for Soft Floors (no surcharge) multidirectional arm rests are height- (10cm), width- (5cm) and depth adjustable (4cm) industry chair TEC in counter version with chromed base backrest with handles BP-Backrest Permanent Contact: The backrest permanently follows the movements of the upper body. Stepless adjustable counter-pressure of the backrest for a body weight of approx kg. Tilt of backrest lockable in 5 positions ST-Synchron Technology with 4 seat tilt: Seat and backrest follow the movement of the sitting person synchronously in the right angle, indirectly noticable adjustment of the backrest counter-pressure for a body weight of approx kg. Synchronous movement stepless lockable AS-Automatic Weight Adjustment: Automatic weight dependent adjustment of the backrest counter-pressure, individually adjustable in two steps. Synchronized weight dependant counter-pressure adjustment of the backrest. Synchonous movement of seat and backrest could be limited in 3 ranges. Backrest lockable in upright position Colour Code: 100: black 300: brown 600: blue 700: bordeaux 800: PU foam 900: aritfical leather 450 technical details are subject to change without notice

3 ESD CHAIR AND CLEAN ROOM CHAIR SHAPE The classic series SHAPE is available with two different backrests, standard and extra high. Its characteristic is an enormous seating comfort. This series is DIN conform and holds the GS symbol. Seat: Base: Backrest (standard): Backrest (high): Casters: 47 x 37 x 43 59cm (WxDxH). Ø 70cm. 43 x 51-57cm (WxH). 43 x 62-68cm (WxH). Soft, for hard floors. Counter Version: Higher gas lift for a seating height of 59 84cm. Height adjustable chromed foot ring with anti-slip surface and base with glides. Note: For safety reason the counter version is not available with casters. Standard or ESD: ESD version is with conductive seat and backrest, conductive casters and polished aluminium base. The chairs are according to DIN EN :2001 for disipation of static charge. The clean room chair fullfills class 4 according to DIN EN ISO (former US Federal Standard 209 E/Class 10) and DIN EN In ESD version according to DIN EN :2001 with polished aluminium base and conductive artifical leather upholsery. Clean Room Chair (high backrest) ESD Chair (high backrest) Swivel Chair SHAPE ESD and Clean Room (xxx: colour code) xxx with PF-Mechanics xxx with ST-Mechanics xxx with PF-Mechanics and High Backrest xxx with ST-Mechanics and High Backrest Clean Room Chair, ST-Mechanics Clean Room Chair, ST-Mechanics and High Backrest Surcharge Conter Version ESD Multidirectional Arm Rest for Shape Option: Hard Casters for Soft Floors (no surcharge) counter version (only with glides!) multidirectional arm rests are height- (10cm), width- (5cm) and depth adjustable (4cm) PF-Backrest Permanent Contact with Spring-Force Adjustment: The backrest permanently follows the movements of the upper body. Stepless adjustable counter-pressure of the backrest for a body weight of approx kg.Tilt of backrest stepless adjustable and lockable. ST-Synchron Technology with 4 seat tilt: Seat and backrest follow the movement of the sitting person synchronously in the right angle, indirectly noticable adjustment of the backrest counter-pressure for a body weight of approx kg. Synchronous movement stepless lockable Colour Code: 100: black 300: brown 600: blue 700: bordeaux 900: artifical leather technical details are subject to change

4 WORKSHOP CHAIR Swivel chair for manufacturing area and workshops with wooden seat and wooden tapering backrest for a maximum of shoulder and arm mobility. Ideal supported back due to pendular mounted backrest. The tilt of the backrest is adjustable and stepless lockable. This series is DIN conform and holds the GS symbol. Base: Seat: Backrest: Casters: Ø 70cm. 42 x 36 x 41 58cm (WxDxH). 43 x 55-63cm (WxH). Soft, for hard floors. Counter Version: Higher gas lift for a seating height of 55 80cm. Height adjustable chromed foot ring with anti-slip surface and base with glides. Note: For safety reason the counter version is not available with casters. Workshop Chair Standard Workshop Chair Surcharge for Counter Version Surcharge for Polished Aluminium Base (Ø 70cm) Option: Hard Casters for Soft Floors (no surcharge) workshop chair with synthetic base WORKSHOP STOOL Stool for the manufacturing area and workshop. Seat with height adjustable gas lift ( mm). Material/ Seat: Base: Seat: Casters: Buche. Ø 60cm. Ø 34cm. Soft, for hard floors. Workshop Stool Workshop Stool with Glides Workshop Stool with Casters workshop stool with glides 452 technical details are subject to change without notice

5 ESD STAND-UP SEAT WITH CASTERS Stepless adjustable sitting height (55-84cm) and sitting tilt. Base: Seat: Upholstery: Casters: Chromed steel, Ø 59cm. 33 x 40cm (WxD). Conductive pure-pu-foam, washable. Load-dependant blocking casters, soft, for hard fl oors. ESD ESD Stand-Up Stehhilfe Seat mit with Rollen Casters ESD Stand-Up Seat with Soft Casters Option: Hard Casters for Soft Floors (no surcharge) STAND-UP SEAT WITH CASTERS AND FOOT RING Stepless adjustable sitting height (55-80cm) and sitting tilt. Base: Seat: Upholstery: Casters: Chromed steel, Ø 61cm. 36 x 36cm (WxD). Conductive pure-pu-foam, washable. Load-dependant blocking casters, soft, for hard fl oors. Stand-Up Seat with Casters and Foot Ring Stand-Up Seat with Soft Casters and Foot Ring Option: Hard Casters for Soft Floors (no surcharge) BASIC STAND-UP SEAT Stepless adjustable sitting height (76-96cm) and sitting tilt. 13 Base: Seat: Upholstery: Frame: 50 x 49cm (WxD). 37 x 36cm (WxD). Conductive pure-pu-foam, washable. Black powder coated. Basic Stand-Up Seat technical details are subject to change

6 SWIVEL CHAIR TOP PRO Unsensitive and hardwearing fabrics. Stepless height adjustable with Toplift (TÜV certified). Medicinically ergonomic backrest with integrated lumbar support, stepless height adjustable. Permanent contact mechanics for the adjustment of the backrest tilt. Ergonomic contoured seat. Nicely shaped and durable base made of black polyamide. Load dependant braked casters for soft floors Swivel Chair TOP PRO (xxx: colour code) xxx Swivel Chair TOP PRO Surcharge for Polished Aluminium Base Ring Arm Rests Height Adjustable Arm Rests Option: Soft Casters for Hard Floors Height: Depth: Width: Backrest: 42-55cm 45cm 46cm 45cm SWIVEL CHAIR SYNCRO PRO Similar to TOP PRO, but with point-synchro-mechanism for a synchroneous movement to adjust seat and backrest tilt, individual adjustable to the body weight. Ergonomic chair recommended for disk herniation. Swivel Chair SYNCRO PRO (xxx: colour code) xxx Swivel Chair SYNCRO PRO Surcharge for Polished Aluminium Base Height Adjustable Arm Rests Option: Soft Casters for Hard Floors Height: Depth: Width: Backrest: 42-55cm 45cm 46cm 55cm SWIVEL CHAIR ALU BASIC Similar to SYNCHRO PRO, but the backrest is with integrated, height adjustable lumbar support and aluminium brace in black; including coat hook. Ergonomic orthopaedic seat. Swivel Chair ALU BASIC (xxx: colour code) xxx Swivel Chair ALU BASIC Surcharge for Polished Aluminium Base Height Adjustable Arm Rests Option: Soft Casters for Hard Floors Height: Depth: Width: Backrest: 42-55cm 44cm 48cm 53cm Colour Code: 101: black 201: anthracite 401: red 501: grey 601: dark blue 701: bordeaux 801: blue 901: mint green 454 technical details are subject to change without notice

7 ESD CHAIR ECONOMY Hardwearing and solid ESD swivel chair according to EN :2001. Gas lift height adjustment (480 68cm) and adjustable backrest. Hardwearing cushioned seat and backrest. Conductive metall base and casters. ESD Chair ECONOMY Textile, black Textile, blue Vinyl, black ESD CHAIR PREMIUM ESD swivel chair according to EN :2001 with ergonomic adjustable mechanisms: seat height with gas lift seat tilt height and angle of the backrest Hardwearing, cushioned seat and backrest. Available in two versions: polished aluminium base with casters for a sitting height of 43 57cm. polished aluminium base with glides and height adjustable foot ring for a sitting height of 50 69cm. ESD Chair PREMIUM Textile with Casters, black Textile with Casters, blue Vinyl with Casters, black Textile with Glides and Foot Ring, black Textile with Glides and Foot Ring, blue Vinyil with Glides and Foot Ring, black ESD CHAIR POLYURETHANE ESD swivel chair for the use in rugged laboratories according to EN :2001 with ergonomically adjustable mechanisms: seat height with gas lift seat tilt height and angle of the backrest 13 Upholstered, washable polyurethane seat and backrest. Available in two versions: polished aluminium base with casters for a sitting height of 43 57cm. polished aluminium base with glides and height adjustable foot ring for a sitting height of 50 69cm. ESD Chair PHOLYURETHANE with Casters with Glides and Foot Ring technical details are subject to change

8 4-LEG VISITOR CHAIR Hardwearing fabrics for seat and backrest. Frame with oval tube, black; stackable. Seat height: 510mm Depth: 420mm Width: 440mm Backrest: 360mm 4-Leg Visitor Chair xxx CANTILEVER VISITER CHAIR OBJECT 2 Visiter chair made Ø 25mm circular tube, black powder coated or chromatized, with plastic glides. Ergonomically formed backrest, rear side of backrest covered with black plastics. Comfortable formed and cushioned seat, lower side covered with black plastics. Optionally with arm rests, stackable. Seat height: 470mm Depth: 480mm Width: 480mm Backrest: 430mm PACKING UNIT: 2 Cantilever Visitor Chair OBJECT 2 (2pcs.) xxx xxx xxx xxx Black Frame, no Arm Rests Black Frame, with Arm Rests Chromatized Frame, no Arm Rests Chromatized Frame, with Arm Rests Colour Code: 101: black 201: anthracite 601: dark blue 701: bordeaux 801: blue 456 technical details are subject to change without notice

9 STUDENT CHAIR FLEX Ergonomically shaped blow-moulding-seat in polypropylene. Grooved seat and backrest for comfortable air ventilation. Stepless height adjustable with steel spindle or gas lift. Base: aluminium base, 5 beams Size: adjustable size 5-7 (sitting height: 41-54cm) Available colours on demand! Student Drehstuhl Chair Flex FLEX Steel Spindle with Casters (height + 2cm) Steel Spindle with Glides Gas Lift with Casters (height + 2cm) Gas Lift with Glides STUDENT CANITLEVER CHAIR Frame: oval tube 35/15/2mm (stackable), epoxy coated (colours on demand!) Size: 6 according to DIN ISO 5970 (sitting height: 46cm) Floor-sparing plastic glides. Type beech: Seat and backrest made of beech multiplex. Type air cushioned: Seat and backrest made of recyclable blow-moulding plastics. Student Cantilever Chair Cantilever Chair Beech Cantilever Chair Air Cushioned STUDENT SWIVEL CHAIR Seat and backrest made of beech multiplex. Base with 5 beams and glides or casters. Type with steel spindle: Foot made of 50mm tube with hidden spindle and turn-out lock for a sitting height of 40-58cm. Type with gas lift: Made of aluminium, stepless adjustable with release lever for a sitting height of 39-54cm with glides and 42-57cm with casters. Frame colours on demand! 13 Student Swivel Chair Steel Spindle with Glides Steel Spindle with Casters Gas Lift with Glides Gas Lift with Casters technical details are subject to change

10 PIN BOARD / ROOM PARTITION Room Partition: Dimensions on demand, maximum size: 1000 x 1900mm oder 1200 x 1700mm. Both sides covered with fabrics in black, brown, blue or bordeaux. Hard foam core for sound protection. Surrounding anodized aluminium frame, width 28mm with plastics corner joints. Outer side with surrounding slot. ESD version with conductive fabrics and earting cable. Partition Stand with Disk-Foot; light grey Plastics disk foot, diameter 400mm. Round tube in standard height 2000mm. Incl. 4 pcs. pre-assembled mounting rings in black. Partition Stand with T-Foot; light grey T-foot, depth 530mm. Round tube in standard height 2000mm. IIncl. 4 pcs. pre-assembled mounting rings in black. Accessory to Pin Board / Room Partition Partition Stand with Disk-Foot, light grey Partition Stand with T-Foot, light grey Partition Element 1000 x 1800mm ESD Partition Element 1000 x 1800mm Partition Element with both foot types Partition with sound protection integrated in a perforated backplane. 458 technical details are subject to change without notice

11 THE RIGHT LIGHT FOR EACH PROCESS Not matter if in laboratories, workshops or technical classrooms, workings have to be done very carefully. For this reason it is important, that the complete workspace is perfectly illuminated without dazzling anyone. Choose the right light for your individual application from our considerable range of lighting systems technical details are subject to change

12 PROFI LED WORKSTATION LAMP ST (STANDARD) Slim design made of anodized aluminium profi le with integrated optics, thus optimal for installation at shelves and racks. Anodized aluminium profi le with cooling ribs. Body 320 tiltable, ø 25mm. Both sides with triangled brackets (W: 95mm) for complete hidden cable runs, with switch. Incl. supply unit 24V. Completely assembled. No cooling required. Continuous LED strip in different length with narrow LED pattern for an absolutely homogenous workspace illumination. Installation: Firmly connected Install Unit with open frame supply unit for bench rack-integration. Attachment Unit fi rmly connected with capsuled supply unit, used for bench combinations WITHOUT bench racks. Add-on Unit with plug-connection to the capsuled supply unit. Retrofi tting unit. DIMMABLE: Optionally with dimming function due to microcontroller-controlled PWM button, selective brightness 0 100%. Technical data: Module length: 300mm, consisting of 28 Osram-LEDs, gapless positioned, module power: 12,5VA. Brightness: 1200lm (>3.300 lux at 500mm distance). Emitting angle: 120. Colour reproduction RA: > 80. Colour temperature: K (daylight white). Colour quality: Single binning according to ANSI (purely selected LEDs for a constant light colour) % DIMMABLE 320º ROTATABLE A (straight) B (angle) distance to bench top in mm Capsuled LED supply unit under shelf 365 x 68 x 38mm (WxDxH) LED with Diffusor/ LED without diffusor LED Workstation Lamp ST 456. B 61. M 0 A B Width (x Module) M Installation A Version 1 500mm 0 INSTALLATION UNIT, not dimmable 1 without diffusor 2 800mm 2 ATTACHMENT UNIT, not dimmable 2 with diffusor mm 1 ADD-ON UNIT, not dimmable 3 waterproof IP67, LED potted in two component PU mm 5 INSTALLATION UNIT, dimmable mm 6 ATTACHMENT UNIT, dimmable mm 7 ADD-ON UNIT, dimmable 460 technical details are subject to change without notice

13 PROFI LED WORKSTATION LAMP PR (PREMIUM) Slim design made of anodized aluminium profi le with integrated optics, thus optimal for installation at shelves and racks. Anodized aluminium profi le with cooling ribs. Body 320 tiltable, ø 25mm. Both sides with triangled brackets (W: 95mm) for complete hidden cable runs, with switch. Incl. supply unit 24V. Completely assembled. No cooling required. Continuous LED strip in different length with narrow LED pattern for an absolutely homogenous workspace illumination. Installation: Firmly connected Install Unit with open frame supply unit for bench rack-integration. Attachment Unit fi rmly connected with capsuled supply unit, used for bench combinations WITHOUT bench racks. Add-on Unit with plug-connection to the capsuled supply unit. Retrofi tting unit. 2-Channel DIMMER with adjustable white: Adjustable brightness between 0 100% Stepless adjustable colour temperature between 2700K (daylight white) to 6000K (cool white). With 2-Channel microcontroller-controlled PWM dimmer with double rocker switch. Technical data: Module length: 400mm, consisting of 42 Osram-LEDs, gapless positioned, module power: 23W. Brightness: 1800 lm (> lux at 500mm distance). Emitting angle: 120. Colour reproduction RA: > 80. White colour temperature adjustable due to alternately arranged 2700K (daylight white) and 6000K (cold white) LEDs. in lux % DIMMABLE 320º ROTATABLE ADJUSTABLE COLOUR TEMPERATURE A (straight) B (angle) distance to bench top in mm 13 stepless adjustable colour: cold white (6000k) daylight white warm white (2700K) LED Workstation Lamp PR 456. B 81. M 0 A B Width (x Module) M Installation A Ausführung Abdeckung 1 600mm 0 INSTALLATION UNIT 1 without diffusor mm 2 ATTACHMENT UNIT 2 with diffusor mm 1 ADD-ON UNIT 3 waterproof IP67, LED potted in two component PU mm technical details are subject to change

14 PROFI LED WORKSTATION LAMP GOOSENECK PR The highly flexible gooseneck allows a completely variable and exact positioning of the luminaire. Gooseneck length: 800mm. Connector with push button (brightness and colour temperature). Rotatable LED stick in aluminium profile with cooling rips. Available in the length of 133, 266 and 400mm. LED stick with contiunous LED modules in premium version with diffusor. Separate 24V supply unit with integrated dimmer, in sheet steel housing 365 x 68 x 38mm (WxDxH). Installation: PROFI adapter, height: 100mm. Bench clamp with max. span width of 90mm. Sliding adapters for the assembly to the ENERGY profile or Multimedia Support. Thus the LED lamp is movable accross the whole bench width. 2-Channel DIMMER with adjustable colour temperature: Dimmable brightness of 0 100%. Stepless adjustable colour temperature between 2700K (warm white) and 6000K (cold white). With 2-channel microcontroller controlled PWM dimmer. Technical Details: Module length: 133mm, consisting of 14 Osram-LEDs, gapeless positioned, module power: 8W. Brightness: 600lm (> lux at 500mm distance). Emitting angle: 120. Colour reproduction RA: > 80. White colour temperature adjustable due to alternately arranged 2700K (daylight white) and 6000K (cold white) LEDs % DIMMABLE ADJUSTABLE COLOUR TEMPERATURE 2-channel dimmer with ajdustable colour temperature separate supply unit with integrated dimmer and power cord PROFI adapter bench clamp sliding adapter for ENERGY profile sliding adapter for Multimedia Support PROFI LED Workstation Lamp Gooseneck PR 456. B 81. M 5 2 B Width (x Module) M Installation 0 133mm 1 PROFI Adapter 3 Sliding Adapter for ENERGY Profile 1 266mm 2 Bench Clamp 4 Sliding Adapter for Multimedia Support 2 400mm 462 technical details are subject to change without notice

15 FULLY POTTED LED IP67 consisting of: LED module strips completely potted in lamp by engased two component compound. Aluminium brackets with encapsuled power cord. Option Hidden Cable Run PROFI LED Workstation Lamp ST and PR OPTION HIDDEN CABLE RUN Milled slot with light grey plastic cover for hidden cable runs on shelves and shelf racks. Option Hidden Cable Run DAZZLE PROTECTOR FOR PROFI LED WORKSTATION LAMP Especially for height adjustable workstations, looking directly into bright light when adjusting the bench height or the emitting angle of the lamp, could not alway be prevented. For this reason we offer dazzle protectors. They are easily attached to the cooling rips of the lamp. Dazzle Protector BB BB Width 05 ST 500mm 14 ST/PR 1400mm 06 PR 600mm 17 ST 1700mm 08 ST 800mm 18 PR 1800mm 10 PR 1000mm 20 ST 2000mm 11 ST 1100mm 13 LAMP ADAPTER FOR CANTILEVER ARM Swiveling rail for the acceptance of the PROFI LED Work station Lamp ST and PR. Durable, light grey powder coating. Bolt (Ø 25mm). Lamp Adapter for Cantilever Arm BB BB Width 05 ST 500mm 10 PR 1000mm 06 PR 600mm 11 ST 1100mm 08 ST 800mm 14 ST/PR 1400mm technical details are subject to change

16 WORKSPACE LAMP 180 tiltable sheet steel housing, sides with mounting brackets. With glare-free parabolic reflector. 36 Watt compact fluorescent lamp. Front with illuminated switch. Rear with 3m cable outlet, no plug. Durable, light grey powder coating. Dimensions: 70 x 95/45mm (DxH). Workspace Lamp BB. V 00 BB Width V Version mm (1x 36W) 0 VVG (low-loss ballast) mm (2x 36W) 3 EVG (electronic ballast) 5 EVG with dimmer UNIVERSAL FLAT LIGHT Extremely flat, nicely shaped design. Prismatic cover for a glare-free illumination. Fluorescent lamp T5 840/830 for bright white light. Electronic ballast (EVG). Dimensions: 105 x 40,5mm (WxH). Universal Flat Light length 608mm / 24 Watt length 908mm / 39 Watt length 1208mm / 54 Watt length 1505mm / 49 Watt optionally with switch 464 technical details are subject to change without notice

17 MAGNIFIER LAMP STANDARD Light grey magnifier lamp with two parallel motion arms, with integrated springs. Luminaire head with optical lens and integrated switch. Incl. luminaire and bench top bracket. Total reach: 1040mm Head: 265/ 230mm. Luminaire: ring-fluorescent lamp 22W (VVG). Biconves-lens: 3 diopter; diameter: 120mm. Magnifier Lamp STANDARD MAGNIFIER LAMP 3D The magnifier lamp 3D is the only lamp, which offers either shade-free illumination from both sides or three-dimensional illumination from either left or right side. This technology is especially for workings on PLC highly appreciated. Total reach: 1040mm. Socket: 2x G23 7W. Squared lens: 3 diopter; 175 x 108mm. Magnifier Lamp 3D Standard Version (light grey) ESD Version (black) MAGNIFIER LAMP PROFI Light grey magnifier lamp with two parallel motion arms, with integrated springs. Liminaire head with removable acrylic lens and mechanical dimmer (50% - 100% light efficiency). Incl. luminaire and bench top bracket. 13 Total reach: 1040mm. Head: 225/ 300mm. Luminaire: TC-L fluorescent lamp 11W EVG. Depth acrylic lens: 3 diopter; 175 x 108mm. Magnifier Lamp PROFI Magnifier Lamp PROFI Additional Lens 4 Diopter Additional Lens 6 Diopter technical details are subject to change

18 MAGNIFIER LAMP DESIGN This is a combination of powerful lamp and modern magnifying glass, hardly warming up while use. It could be equipped with additional magnifier glasses. Arm with joint and integreated spring (arm length: 1000mm). Incl. luminaire: T-5C 22 Watt. Diopter: 3,5; magnification: 185%; Lens material: glass; focal distance: 280mm Magnifier Lamp DESIGN Magnifier Lamp DESIGN Swivel Lens 4 Diopter Swivel Lens 6 Diopter LED MAGNIFIER LAMP VARIO Solid metal lamp in elegant design, flexible parallel motion arm with excellent illumination. Excellent optics, glas lens Ø 127mm. Accurat positioning of the LEDs offer an almost shade-free magnification. Maximum of flexibility and precision. Energy consumption only 11W. Dimmable. Automatic shut-off after 4 or 9 hours. Optionally with 3 or 5 diopter. Operating hours: approx h. LED Magnifier Lamp VARIO, light grey with 3 Diopter with 5 Diopter ESD LED MAGNIFIER LAMP VARIO Solid metal lamp in elegant design, flexible parallel motion arm with excellent illumination. Excellent optics, glas lens Ø 127mm. Accurat positioning of the LEDs offer an almost shade-free magnification. Maximum of flexibility and precision. Energy consumption of only 11W. Dimmable. Automatic shut-off after 4 or 9 hours. Optionally with 3 or 5 diopter. Operating hours: approx h. ESD LED Magnifier Lamp VARIO, black with 3 Diopter with 5 Diopter 466 technical details are subject to change without notice

19 TASK LAMP Parallel motion arm made of steel with integrated springs. Luminaire head made of steel with integrated switch. Incl. luminaire and screw clamp. Reach: 1040mm. Head: 100/ 470mm. Luminaire: 2x T26 fluorescent lamp 15W. Cable: 1,8m. Task Lamp with Electronic Ballast LED TABLE LAMP The LED Table Lamp with spring-balanced arm, reach 800mm is easily adjustable to different positions while the luminaire is always in parallel to the bench top. Glare-free and homogeneous illumination. Power: 10W. Screw clamp for bench fixation. Colour reproduction between Ra 92 and 3000K. Average working duration at normal use: 25 years. LED Table Lamp HALOGEN LAMP Lamp with spring-eased motion arm. Luminaire head with heat isolation, incl. luminaire. 13 Arm: mm. Lamp head: Ø 71 x 100mm. Luminaire: halogen lamp 20W. Colour: grey / black. Optionally with light tube: light tube 10mm, diameter, length: 800mm. Cable: 1,5m. Halogen Lamp Halogen Lamp Table Clamp Light Tube technical details are subject to change

20 BENCH TOP SLEEVE For table -, magnifi er - and examination lamp. For all lamps with fi xation bolt of Ø 12,7mm. Bench Top Sleeve PROFI SWIVEL ARM AND SLEEVE FOR LAMP Solid steel swivel arm with sleeve / bolt combination. Load max.: 50kg. Modular confi gurable with: - Sleeve for the assembly to the PROFI profi les. - Heavy load swivel arm with bolt, sleeve and fi xing screw. Available in different length, incl. cord clamp. - Different end pieces with bolt available. Solid plastics adapter for reduction of the bolt diameter to Ø 12mm, suitable for lamps. PROFI Swivel Arm PROFI Swivel Arm and Sleeve for Lamps Sleeve for PROFI Swivel Arm Ø 25mm PROFI Swivel Arm / reach: 250mm PROFI Swivel Arm / reach: 300mm PROFI Swivel Arm / reach: 500mm Set 1: Sleeve + Swivel Arm 300mm Set 2: Sleeve + Swivel Arm mm PROFI Sleeve for Lamp Ø 12mm Sleeve and Swivel Arm and Sleeve for Lamp TFT SUPPORT FOR PROFI SWIVEL ARM Tiltable adapter for VESA standard (100 x 100 und 75 x 75). Durable, light grey powder coating. Bolt (Ø 25mm). TFT Support for PROFI Swivel Arm TFT Support TFT Support with Key Board Tray TFT Support with Keyboard Tray and Swiveling Mouse Pad 468 technical details are subject to change without notice

21 MODULAR SWIVEL ARM SYSTEM DESIGN 1. Bench top fixation with 4 USB sockets, either with clamp or through the bench top, span width: 8-75mm. 2. Bench top fixation, height 260mm or 570mm. 3. Clamp fixation for tool-less and stepless adjustable height swivelling to both sides for flexible positioning. 5. Stepless adjustable with spring. 6. Vertical stroke 228mm for an optimal height adjustment swivelling to the right or left side. 8. Up or down tilt of rotatable standard VESA adapter 75/100, (monitor either horizontal or vertical). 10. Cord holder at the swivel arm and foot for a protected and clear cable arrangement. FOOT FOR TFT SWIVEL ARM DESIGN For clamp fixation and through bench top. With 4 cord holders and end cap. Clamp fixation: 8-75mm. Height: 260mm/ 570mm. Foot for TFT Swivel Arm DESIGN height: 260mm height: 570mm SLIDING CLAMP FOR FOOT 13 For the fixation of one or two TFT swivel arms to the foot. With cord holder. Sliding Clamp for Foot Single Sliding Clamp with 1 Cord Holder Double Sliding Clamp with 2 Cord Holders double sliding clamp for the fixation of two TFT swivel arms on same height technical details are subject to change

22 PROFILE CONNECTOR FOR TFT SWIVEL ARM DESIGN With cord holder. Height: 90mm / width: 51mm Incl. assembly set. Profile Connector TFT SWIVEL ARM DESIGN Swivel arm short for TFT monitors 5kg or 7,5kg. Reach: 90mm. Adjustable tilt swiveling head piece. TFT Swivel Arm DESIGN Load: 5kg Load: 7,5kg TFT SWIVEL ARM DESIGN, NO HEIGHT ADJUSTMENT Swivel arm in two different length for the acceptance of TFT monitors 5kg or 7,5kg. Reach: 250mm or 430mm. 180 swiveling head piece. With cord holder. TFT Swivel Arm DESIGN, no height adjustment Reach 250mm/ Load: 5kg Reach 250mm/ Load: 7,5kg Reach 430mm/ Load: 5kg Reach 430mm/ Load: 7,5kg TFT SWIVEL ARM DESIGN, HEIGHT ADJUSTABLE Swivel arm in two different length for the acceptance of TFT monitors 5kg or 7,5kg. Reach: 330mm or 510mm at full length swiveling head piece. Adjustable height more than 150mm. TFT Swivel Arm DESIGN, height adjustable Reach 330mm/ Load: 5kg Reach 330mm/ Load: 7,5kg Reach 510mm/ Load: 5kg Reach 510mm/ Load: 7,5kg 470 technical details are subject to change without notice

23 PROFI TFT SWIVEL ARM Suitable for TFT monitors between 14 and 18 diagonally. Load between 2,5kg and 8,5kg. According to VESA standard (75 x 75mm and 100 x 100mm). Screw-operated weight adjustment. Hidden cable run within the plastic cover. Rotation angle 360, total length 400mm. Stepless adjustable between 0 (horizontal) and approx. 90 (vertical). Colour: light grey RAL PROFI TFT Swivel Arm Sleeve for hera extensions Fixation with 80mm cable access ring Standard with extra cantilever (250mm) with extra cantilever (250mm) and keyboard tray PROFI TFT SUPPORT LC FOR CROSS PROFILE Rotation -, Tilt- und Swivel adjustment, with VESA adapter (100x100 and 75x75), max. load: 5kg. Made of die-cast aluminium. Durable powder coating in white aluminium. 13 PROFI TFT Support LC joint (94mm reach) 2 joints (302mm reach) 3 joints (482mm reach) technical details are subject to change

24 PROFI TFT SUPPORT PLUS FOR CROSS PROFILE Tilting and swiveling, with VESA adapter (100x100 and 75x75mm), max. load: 15kg. Durable, light grey powder coating. Depth: 110mm. PROFI TFT Support PLUS PROFI TFT SWIVEL ARM TSS Hight quality arm made of anodized aluminium. Adjustable movability of the joints. Ball-and-socket joint for a precise positioning of the monitor. VESA adapter 75/100 with quick connector for an easy monitor change without tool. In swivel arm integrated cord holder for a protected and clear cable arrangement ball-and-socket joint with quick connector integrated cord holder PROFI TFT Swivel TFT-Schwenkarm Arm TSS TSS Swivel Arm TSS1, reach 105mm max. load: 15kg Swivel Arm TSS2 reach: 250mm, 1 joint, max. load: 15kg Swivel Arm TSS3 with 2 joints, reach: 450mm max. load: 10kg Swivel Arm TSS4 with 2 joints, reach: 505mm; max. load: 15kg technical details are subject to change without notice

25 FLEX POWER OUTLET STRIP Solid power outlet strip in screw-fixed plastic housing. Connecting cable H05VV-F3G 1,5mm². Optionally with illuminated 2poles switch, 16A. Dimensions: 56 x 41mm (WxH). FLEX Power Outlet Strip Schuko 3fold (L:185) white, no Cord Schuko 3fold (L:185) black, no Cord Schuko 3fold (L:185) white, with 1,5m Cord Schuko 3fold (L:185) black, with 1,5m Cord Schuko 3fold (L:185) white, with 3,0m Cord Schuko 3fold (L:185) black, with 3,0m Cord Schuko 3fold (L:185) red, with 3,0m Cord Schuko 3fold (L:185) white,with 5,0m Cord Schuko 3fold (L:185) black, with 5,0m Cord Schuko 4fold (L:288) white, no Cord Schuko 4fold (L:288) white, with 1,5m Cord Schuko 4fold (L:288) black, with 1,5m Cord SEV weiss Schuko 4fold, with Swiss Plug Schuko 4fold (L:288) white, no Cord with Switch Schuko 4fold (L:288) white, with 1,5m Cord with Switch Schuko 4fold (L:288) black, with 1,5m Cord with Switch SEV 4fold white, with Switch and Swiss Plug Schuko 6fold (L:340) white, no Cord Schuko 6fold (L:340) black, no Cord Schuko 6fold (L:340) white, with 1,5m Cord Schuko 6fold (L:340) black, with 1,5m Cord SEV white 6fold, with Swiss Plug Schuko 6fold (L:340) white, with 3,0m Cord Schuko 6fold (L:340) black, with 3,0m Cord Schuko 6fold (L:340) white, with 5,0m Cord Schuko 6fold (L:340) black, with 5,0m Cord Schuko 6fold (L:340) white, no Cord with Switch Schuko 6fold (L:340) white, with 1,5m Cord with Switch Schuko 6fold (L:340)black, with 1,5m Cord with Switch SEV 6fold white, with Switch and Swiss Plug Schuko 6fold (L:340) white, with 3,0m Cord with Switch Schuko 6fold (L:340) black, with 3,0m Cord with Switch Schuko 6fold (L:340) white, with 5,0m Cord with Switch Schuko 6fold (L:340) black, with 5,0m Cord with Switch Mounting Set for FLEX Power Outlet Strip POWER OUTLET STRIP INDUSTRY Hight quality power outlet strip made of silver plastic profile and child-protected black Schuko sockets (45 position), black end cap and mounting tongues. Black connecting cord H05VV-F 3G1,50mm² (length: 2m) with angled Schuko plug. Dimensions: 70 x 45mm (WxH). 13 Power Outlet Strip INDUSTRY fold with Switch (L: 355mm) fold with Switch (L: 570mm) fold with Switch (L: 440mm) fold with Switch (L: 700mm) technical details are subject to change

26 19 POWER OUTLET STRIP 1HE Anodized aluminium profile with light grey Schuko sockets (45 position) and stainless steel brackets with 19 fixing holes (90 turnable). Black connecting cord H05VV-F 3G1,50mm² (length: 2m) with angled Schuko plug. 19 Power Outlet Strip 1HE fold, with Switch and Overvoltage Protection, Mains - and Frequency Filter fold, with Switch and Overvoltage Protection (optical function and failure indication) fold, with RCD 30mA, 2poles fold, with Switch fold, with Circuit Breaker B 16A, 2poles fold, no Switch SOCKET UNIT FOR FURNITURE INTEGRATION Silver steel frame (248 x 151mm). Solid flap-mechanism, snapping into end positions (depth: 56mm). Flap could be closed even if plugged in, due to integrated brush strip. Solid clamp fastening for bench tops between 18mm to 30mm. The socket unit is inserted into the completely mounted flap-mechanism. Socket Unit for Furniture Integration fold with 2x RJ45 and 1x VGA socket 2fold with 2x RJ45 3fold MODULAR SOCKET SYSTEM STEP Modular connectible protection - and socket system in aluminium-plastic housing. Single modules can be set-up in flexible configurations and connected from bench to bench Modular Socket System STEP Overvoltage Protection 2kV w. Mains Filter 30MHz 3fold Schuko Socket, black 3fold Schuko Socket, red RCD/ Line Circuit Breaker 16A, 400V, 2poles Connecting Cable H05VV-F3G 1,5mm², 2m Power Cord H05VV-F3G 1,5mm², 3m 3fold Schuko Socket, black with Switch Fixing Brackets made of Stainless Steel, 2pcs technical details are subject to change without notice

27 TEST LEADS WITH 2MM LAMELLA PLUG Highly flexible connecting cable. Both sides with stackable 2mm lamella plug. Rated current: 10A. Approved contact voltage for 4mm measuring leads (not insulated): 30V AC/60V DC. Test Lead L.0 F F L Length FF Colour 0 7,5cm 6 45cm 02 black 06 red 10 green 14 grey 2 30cm 8 60cm 04 brown 08 yellow 12 blue 18 white TEST LEAD WITH 4MM LAMELLA PLUG Highly flexible connecting cable. Both sides with stackable 4mm lamella plug. Rated current: 32A Approved contact voltage for 4mm measuring leads (not insulated): 30V AC/60V DC. Approved contact voltage for 4mm measuring leads (contact protected with safety plugs): 1000V. 4mm lab plug (not insulated) 4mm safety plug (contact protected) Test Leads A L.0 F F0 A Type L Length FF Colour 1 Test Lead 0 25cm 4 100cm 02 black 06 red 10 yellow 14 blue 18 white 3 Safety Test Lead 2 50cm 6 150cm 04 brown 08 yellow/ green 12 green 16 grey Set A. S 00 A Type S Pcs. 1 Test Lead 1 50x Cable Lengths 25, 50 and 100cm in Different Colours 3 Safety Test Lead x Cable Lengths 25, 50, 100 and 150cm iin Different Colours 160x Cable Lengths 25, 50, 100 and 150cm iin Different Colours 13 PLUG CONNECTOR AND ADAPTER Plug Connector Plug Connector 2mm (pin distance 5mm) Plug Connector 4mm (pin distance 19mm) Plug Connector 4mm (pin distance 38mm) Adapter 4mm Plug to 2mm Jack, black Adapter 4mm Plug to 2mm Jack, red Safety Plug Connector 4mm (pin distance 19mm) technical details are subject to change

28 CORD HOLDER FOR PROFI Cable comb made of aluminium sheet, with different gaps for the acceptance of cables up to 12mm thick. Durable, light grey powder coating. Incl. assembly set for the fi xation to the PROFI profi les. Height: 30mm. Width / no. of gaps Depth 300/17 500/31 603/37 800/ /56 80mm mm CABLE SUPPORT WITH SLIDING PINS Aluminium U-Profi le with individual sliding pins, plastic. The sliding pins could be individually adjusted to the different cable diameters. Cable Support with Sliding Pins Sliding Pin L: 255mm with 16x Sliding Pins L: 500mm with 34x Sliding Pins L: 1000mm with 69x Sliding Pins PROFI CABLE SUPPORT Cable support with bow and integrated cable comb, made of 3mm thick aluminium sheet. Cable comb suitable for laboratory cords, power cords, etc. Durable, electrical conductive powder coating in light grey. Dimensions: 160 x 100 x 65mm (WxDxH). PROFI Cable Support PROFI HOSE AND CABLE SUPPORT Hose support made of aluminium die-cast. For the storage of hoses and cables. Dimensions: 190 x 70mm (WxD). PROFI Cable Support technical details are subject to change without notice

29 CLAMP-TYPE TEST PROBE Clamp-type test probe with elastic grip jaw in fl exible tube and 4mm jack. Clamp-Type Test Probe red black TEST PROBE Test probe with plug connection to 4mm jack and steel measuring pin. Test Probe red black CROCODILE CLIP Test clip for bolts up to 20mm front part with fi ne-wire surface and 4mm jack. Crocodile Clip red black BNC CABLE BNC test lead 50Ω, with 2 BNC plugs and bend protection. Colour: black. BNC Cable cm 100cm 200cm BNC EXTENSION CABLE BNC test lead with BNC plug and BNC connector, 50Ω. Colour: black. BNC Extension Cable cm 200cm BNC ADAPTER Adapter from two rigid 4mm socket to BNC. BNC Adapter with BNC Plug with BNC Socket technical details are subject to change

30 RUBBER MAT The rubber mat protects the work top of heavy or sharp-edged devices. Dimensions: 525 x 365 x 7mm (WxDxH). Colour: black. Rubber Mat ANTISTATIC RUBBER GRID-MAT This solid rubber mat protects the bench top of sharpedged and sensible devices. The grid catches splinters and separates small parts. Dimensions: 625 x 375 x 20mm (WxDxH). Colour: black. Antistatic Rubber Grid-Mat RUBBER MAT (PER METER) Tailored rubber mat for the protection of the complete bench top or as fl oor mat. Surface either fl at or rilled. Resilent to disruptive discharge from 4mm thickness up to 50kV (VDE 0680). Width: 1000mm, colour: grey. Rubber Mat (per meter) B S 0 B Thickness S Thickness 1 3mm, rilled mm 2 4,5mm, rilled mm 3 4mm, fl at Tailoring Straight Cutout per Running Meter Squared Cutout EROGONOMIC FLOOR MAT STANDARD PU Ergonomic fl oor mat, foamed PU. Semicircular foams (Ø 19mm), for mostly standing occupations. Colour: grey. Thickness: 14mm Ergonomic Floor Mat Standard PU x 900mm / pcs. 600 x 1800mm / pcs. 900 x 1200mm / pcs. 900 x 1800mm / pcs. 478 technical details are subject to change without notice

31 ESD BENCH MAT Double-layered bench mat with rounded corners. Material: Synthetic rubber, double-layered. Contact: 2 press studs 10,3mm. The top layer is mostly resistant to soldering spatters, the low-ohmic structure material provides a continuous resistance of approx. 10MOhm. ESD Bench Mat x 1000mm (beige) 600 x 1000mm (platinum grey) 600 x 1000mm (olive green) 600 x 1000mm (light blue) 600 x 1200mm (beige) 600 x 1200mm (platinum grey) 600 x 1200mm (olive green) 600 x 1200mm (light blue) ESD FLOOR MAT The structure of the mat guarantees finest laying characteristics without curls and risk of stumbling. The surface is resistant to swivel chairs and shortly withstands intense heat, e.g. soldering splatter. Material: synthetic rubber, double-layered. Standard size: 1500 x 1200 x 2,5mm or per meter, max x 10000mm (no press studs). Contact: 2x press studs 10,3mm. Colour: platinum grey. ESD Floor Mat x 1200mm (with press studs) per meter: roll width: 1900mm (no press studs) the synthetic rubber with its electrical conductive lower layer, with pointwise contact to the surface, guarantees an optimal electric conductance ESD MAT PER METER Made of synthetic rubber, shortly heat resistant (e.g. soldering splatter), double-layered with low-ohmic structure material. Certified according to VDE DIN EN Discharge resistance: MΩ 13 ESD Mat B. 4 ST B Width ST Thickness mm 00 2mm (beige) mm 02 2mm (platinum grey) 04 2mm (olive grey) mm (light blue) 3,5mm (platinum grey) the mat ensures a safe and rapid discarge of electric loads in ESD protected areas technical details are subject to change

32 ESD CONNECTOR For the easy realization of ESD earth connection with integrated 1MΩ protective resistor ESD Connector Schuko - Press Stud 10,3 with 1,5m Cable Schuko - 3x Press Stud 10, Eylet Screw - 2x Press Stud 10,3 with 1,5m Cable Schuko - 6x Press Stud 10,3 with 1,5m Cable WRISTBAND / COILED CORD Textile wristband with elastic-strap and non-allergic synthetic material. Integrated 1MΩ resistor. Connected with 10mm press stud. Length of coiled cord: 2400mm, both sides with press stud 10mm. ESD Handgelenkarmband/Spiralkabel Wrist Band / Coiled Cord Wirst Band with Coiled Cord Wirst Band Coiled Cord ESD BASIC SET Conductive bench mat platinum grey with round corners made of antistatic systhetic rubber, 900 x 600 x 2mm. Two press studs for the connection of the wrist band cord. Earthing cord with press stud and crocodile clip. Textile wrist band with elastic-strap, coiled cord and press stud. ESD Basic Set CUSTOMIZING RUBBER MATS On demand we cut above rubber mats into specific dimensions, make cutouts for profile extensions and insert press studs. Adhesive foil with micro-perforation and ventilation grooves enables an easy and bubble-free tape down on bench tops or floors. The respective surface is instantly usable, the foil can be removed without residue. For an easy handling the foil is protected with peel-off paper. Resilent to stool casters. Suitable for under-floor heating. The punching tool is for later modifications of your mat with press studs 10,3mm. Customizing Rubber Mats Straight Cut per Meter Squared Cut Punching Tool incl. Press Studs 10,3mm 1m of Bothsides Adhesive Foil (width: 1m) 480 technical details are subject to change without notice

33 ESD DOCUMENT HOLDER DIN A4 10x DIN A4 document protectors made of electrostatic polyethylene, fitted in black metall frames. Holder made of stainless steel incl. assembly set for the fixation to the PROFI extensions. ESD Document Holder DIN A TURNTABLE Stainless steel disk with ribbed rubber surface. Load capacity: 180kg. Height: 20mm. Position lock with stop-pin in 45 steps, free-wheeling possible. ESD Type: Conductive ribbed rubber surface with earthing cable. Turntable A. D 0 T A Type D Diameter T Version 0 Standard 3 380mm 0 no position lock 5 ESD 5 500mm 5 with position lock ESD FOOT REST Solid, conductive and tilting foot rest with earthing cable. Black surface (450 x 350mm). Height front: mm. Height rear: 70-75mm. ESD Foot Rest TOOL HOLDER All tools always at hand. Flexible plastic tool hangers for easy attach- and detachment. Colour: black. Dimensions: 44 x 35 x 30mm (WxHxD). Tool Holder technical details are subject to change

34 HOLDER FOR PERFORATED BACKPLANES For hooking into perforated backplanes, with screw lock. Steel made, durable plastic coating in aluminium colour. Set pcs. 18pcs. 28pcs. 40pcs. Holder with Tilted Hook Holder with Double-Hook L: 50mm / Ø 6mm x 35mm (LxW) L: 100mm / Ø 6mm x 35mm (LxW) L: 150mm / Ø 6mm x 35mm (LxW) L: 200mm / Ø 6mm x 35mm (LxW) Holder with Clip Holder for Pliers with Clip (Ø 13mm) x 20mm (WxD) with Clip (Ø 19mm) x 20mm (WxD) with Clip (Ø 25mm) x 20mm (WxD) with Clip (Ø 32mm) Holder for Electric Tools Holder for Cable Ø 40mm x 37 x 50mm Ø 60mm x 37 x 50mm Ø 80mm Holder for Screw Driver Holder for Screw Driver Screw Driver Screw Driver Screw Driver Holder for Drill and Allen Wrench Holder for Storage Boxes Tools single Tools x 60mm (WxH) x 38mm (WxH) Document Holder Shelf x 310mm (WxH) x 125mm (WxD) x 150mm (WxD) 482 technical details are subject to change without notice

35 SMALL PART MAGAZINE STANDARD The drawers are made of transparent and unbreakable polypropylen, separatable by partitions and labelable. Prepared for wall mounting. Sheet steel, anthracite powder coated. 307 x 150 x 555mm (WxDxH). Small Part Magazine Standard with 8 Drawers with 16 Drawers with 24 Drawers with 40 Drawers with 48 Drawers with 60 Drawers SMALL PART MAGAZINE ESD The drawers are made of conductive black plastics with carbon-fibres. Prepared for wall mounting. Sheet steel, anthracite powder coated. 307 x 150 x 555mm (WxDxH). Small Parts Magazine ESD with 24 Drawers with 48 Drawers with 60 Drawers ROTARY TOWER The rotary tower is modularly and flexibly equipable with above mentioned small part magazines. Sheet steel, anthracite powder coated. Could be equipped with 12 small part magazines. Easy running due to wearfree ball bearings. 680 x 680 x 1760mm (WxDxH). 13 Note! This article No. does not include small part magazines. Rotary Tower for Small Part Magazines Standard ESD technical details are subject to change

36 STORAGE BINS Storage bins made of polypropylene with lable holder and hooking strip for cross bin bars. Stackable with lable holder. The standard is available in grey, green, blue, red and yellow. ESD Version: Made of conductive black plastics with carbon-fibres. Storage Bin 296. GGG. A 01 GGG Size (LxWxH) A Version x140x130 1 Standard x140x x105x75 2 ESD Standard ESD x105x45 EURO TRANSPORT BOXES Stackable transport boxes in standard size. Specially suitable for the convenient transport of products on transfer systems like roller - or ball transfer bands. ESD Verison: Made of conductive black plastics with carbon-fibres. Standard ESD Euro Transport Boxes 296. GGG. A 01 GGG Size (WxDxH) A Version x200x x300x x300x x400x212 1 Standard x200x x300x x400x x400x278 2 ESD x300x x300x x400x x400x x300x100 SLIDING NUTS FOR ALUMINIUM PROFILES Einschwenkmutter Sliding Nut for PROFI Profile M5 Sliding Nut for PROFI Profile M Sliding Nut for PROFI Profile M Heavy Duty Sliding Nut M8 (67x20x8mm) Cage Nut M6 for Back Planes Thread Nut M6 19x19 for Didact Profile rear Thread Nut M4 for Didact Profile front Sliding Nut for 30x30 Cross Profile M Sliding Nut for 30x30 Cross Profile M Sliding Nut for 30x30 Cross Profile M8 484 technical details are subject to change without notice

37 ELECTRICIAN VICE WITH BALL JOINT BASE Rotatable in all directions with position lock and replacable plastic jaws. Clamping pressure: 150kp; opening width: 70mm. Clamping depth; 38mm; jaw width: 50mm. Electrician Vice with Ball Joint Base BASE WITH BALL JOINT For the fixation to laboratory benches with max. bench top 80mm thick. Base with Ball Joint ELECTIRCIAN VICE With replacable plastic jaws. Clamp pressure: 150kp; opening width: 70mm. Clamping depth; 38mm; jaw width: 50mm. Electrician Vice TURNING HEAD FOR PLC HOLDER Quick turning meachanism with angled adapter. For an easy and quick 180 -turn of the PLC holder with automatic stop. Turning Head for PLC Holder PLC HOLDER Fixed clamp holder for the acceptance of PLCs, so they do not have to be touched. Clamp length: 70mm; adjustable width: mm. Central position: adjustable. PLC Holder PLC HOLDER, LARGE Fixed clamp holder for the acceptance of PLCs, so they do not have to be touched. Clamp pressure: 350kp; adjustable width: mm. Central position: adjustable. 13 PLC Holder, large PLC COVER PANEL For the fixation of the components while turning the PLC for soldering. Dimensions: 315 x 330mm. PLC Cover Panel technical details are subject to change

38 MECHANIC VICE HEUER vice with forged jaws for circular pipes, clamping jaws for great depth, easy adjustable centric clamping mechanism, precision spindle-bearing with two-turn trapezium thread; groofed jaws. Jaw width: Span detph: Pipe Ø min./max.: 120 mm 65 mm mm Mechanic Vice Vice Standard Vice with Exchangable Jaws Jaws PP (polypropylene) Jaws (PR) for Pipes Mechanic Vice Mechaniker-Schraubstock FOLDING MECHANISM FOR MECHANIC VICE For a maximum of working space, the vice could be folded below Height the bench Adjuster top for if Mechanic not in use. Vice In working position the vice is approx. 175mm height adjustable and could be turned by 360. Lowest position: Folding depth: Pivoting radius: 590mm 460mm 430mm Folding Mechanism for Mechanic Vice Lifting Mechanism (turning and lifting mechanism) Automatic Folding Mechanism with Gaslift Manual Folding Mechanism with Spindle Fold Mechanism for Height Adjuster technical details are subject to change without notice

39 MOBILE SOLDERING FUME EXTRACTION FOR 1-2 WORKSTATIONS Compact and portable soldering fume extraction system. System with powerful fan, with prefilter and efficient standard filter. The low-noise, powerful and wearfree pump motor extracts toxic fumes around the workstation. Compact system, fits unter the bench. Variable fan speed. 350m³ air volume per hour. 75mm tube diameter. Noise level less than 50dB. Dimensions: 460 x 310 x 310mm. Hose approx. 250 cm, 2 pcs. in delivery scope. 3fold-filter system (pre-filter/hepa/carbon). Mobile Sodering Fume Extraction for 1-2 Workstations Mobile Soldering Fume Extraction Set of Standard Filters Pre-Filter WELLER SOLDERING FUME EXTRACTION FOR 1-2 WORKSTATIONS The Weller Zero Smog extraction system eliminates air pollution caused by soldering fume, adhesive vapours or laser smoke. The powerful maintenance-free vacuum fan generates a continuous fume extraction with a max. air flow of 220m 3 /h. The optimized co-relation of turbine and filtering unit almost clears the air by 100%. Technical Details: Dimensions 320 x 320 x 395mm (LxWxH). Power consumption 115VA. Noise level 52db(A) in 1m distance. Max. vacuum 1800Pa. Max. air flow 220m 3 /h. Max. capacity 2 workstations. Fine particle filter F5. HEPA filter efficiency H12 (99,5 particle up to 0,3µm) combined with a wide band gas filter (active cabon foam) Including Extraction arm: 1m. Extraction hose: 3m with hood-nozzle. Table clamp with stop-valve. Adapter. Two hose clamps. Compact filter Weller Soldering Fume Extraction Set Soldering Fume Extraction Set for 2. Soldering Fume Extracton Additional Nozzle Adapter to Diameter 50mm technical details are subject to change

40 SOLDERING FUME EXTRACTION 702 Solid sheet steel housing with white powder coating RAL9010 and blue RAL5013. Completely sound-insulated housing. Top with two hose connectors NW 50. Easy to use operation panel with filter-full indication. Filter unit and complete set of filters, consisting of pre-filter, HEPA filter H13, seperation efficiency according to EN ,95%, refillable active carbon filter in exchangable casing. Fan unit. Two swivel casters, two fixed casters. Technical Details: air flow fan capacity free-blowing 240 m³/h motor 0,12kW total pressure 1350Pa noise level 50dB(A) efficiency 99,95% dimensions: 340 x 430 x 600mm (WxDxH) IP44 for 1-3 Workstations SOLDERING FUME EXTRACTION 802 Solid sheet steel housing with maintenance flap, bothsided powder coated in RAL9010 and blue RAL5013. Three filters with pre-filter F5, high-efficiency filter class H13, tested according to EN 1822 with separation efficiency of > 99,95% at particle size of 0,3μm; gaseous pollutions are cleared in a steel cassette, filled with 2,7kg specially coated active carbon; easy to use operation panel with filter-full indication; maintenance-free motor, ideal for continuous operation. Technical Details: effective air flow 281m³/h fan air flow 390m³/h total pressure 4000Pa nominal power /motor 0,24kW nominal voltage 230Volt frequnecy 50Hz noise level in 1 mtr. distance 58dB(A) hose adapter at the rear side, optionally 1x NW100 or 4x NW50. dimensions: 400 x 500 x 760mm (WxDxH) IP55 for 2-5 Workstations This systems is an ideal solution for a continuous and highly efficient extraction and air filtering for soldering fumes, consisting of harmful fumes, gases and aerosoles. The polluted air is succed with extraction arms. For an efficient air clearing we offer differend nozzles. The extracted pollutants are transported to the filter unit in an individually for you designed set-up of hoses. The 3fold filter system clears the air with an efficiency of 99,95% (DOP-Test). 488 technical details are subject to change without notice

41 EXTRACTION ARM - RIGID Soldering fume extraction arm, mounted with table clamp or flanged to the bench top. Tube diameter 50mm. Recommended air flow: m 3 /h. Tubes: conductive, galvanized aluminium. Joints: conductive PP, black Integrated throttle. Earting cable with 1MOhm resistor. Flange for bench top access 60mm Extraction Arm System - Rigid Table Clamp, black Extraction Arm with 2 Joints (reach: 445mm) Extraction Arm with 2 Joints (reach: 545mm) Extraction Arm with 2 Joints (reach: 645mm) Extraction Arm with 3 Joints (reach: 765mm) Extraction Arm with 3 Joints (reach: 945mm) Extraction Arm with 3 Joints (reach: 1125mm) Gap-Nozzle (width: 200mm) Nozzle (length: 210mm) Hood-Nozzle (diameter: 200mm) EXTRACTION ARM- FLEXIBLE Soldering fume extraction arm, mounted with table clamp or flanged to the bench top. Tube diameter 50mm. Recommended air flow: 45-85m 3 /h. Tubes: conductive, galvanized aluminium in combination with a flexible, self-holding hose made of black polypropylene (PP). Flange made of conductive PP, black for bench top access at 60mm cutout. Joints: conductive PP, black Integrated throttle. Nozzle made of anodized aluminium. Earting cable with 1MOhm resistor. Extraction Arm System - Flexible Table Clamp, black Extraction Arm, no joint (reach: 600mm) Extraction Arm with 1 joint (reach: 700mm) Extraction Arm with 2 joints (reach: 900mm) Connecting Set Extraction System - Extraction Arm Zubehör Hose Set 1,25m for Extraction System 702/ Hose Set 2,5 for ExtractionSystem 702/ Hose Set 5m for Extraction System 702/ Hose Set 1,25m for Mobile Extraction System Hose Set 2,5m for Mobile Extraction System Hose Set 1,25m for Weller Extraction System Hose Set 2,5m for Weller Extraction System technical details are subject to change

42 TEST HOOD Dimensions: 530 x 900 x 660mm (WxDxH). Plastic base with room for the installation of adapters for test items. Swiveling semicircular perspex hood with handle and safety switch. Rear and side walls made of plastics. Test Hood pcs. TEST CABINE Perspex cabine, that could be pushed up and down within the slots of the PROFI profile. While testing, the cabine is safely closed with an electromagnetic lock. When the cabine is pushed-up for opening, it is automatically discharged. Signal lamp for status indication. Testkabine Cabine x 790 x 600mm (WxDxH) 1295 x 790 x 600mm (WxDxH) 490 technical details are subject to change without notice