Instruction Manual. Item No: AL506

Size: px
Start display at page:

Download "Instruction Manual. Item No: AL506"

Transcription

1 Instruction Manual Item No: AL506 Specifications: Wingspan: 2218mm (87.3 in) Length: 1892mm (74.5 in) Wing Area: 100dm2 (1550 sq in) Flying Weight: 7.3kg (16.1 lbs) Engine(not incl.): 50-60cc Gas Radio(not incl.): 4 ch, 6 servos Construction: Balsa and Plywood Features: Designed for high performance scale aerobatics High-quality balsa and plywood material Light weight and strong construction Foam brace on the back of fuselage Enhanced cowling mounting design Hardware package included High-quality, prepainted, fiberglass cowling and wheel pants Nice color scheme with professional covering Picture may not be the same as actual product. Please refer to actual product. We reserve the rights of updating product information, appearance and parameters without notice.

2 Table of Contents Appendix Parts and Options 21

3 Fully assemble the model. With a helper, lift the airplane with your index fingers to find the balance point. The balance point (CG) should lie between the two marks on the wing. If not, try to move some parts such as batteries to different position, or add the necessary weight to the nose or tail to obtain the correct balance. Preflight Introduction Congratulations on the purchase of this model airplane. You will enjoy one of the most thrilling experiences the radio control hobby has to offer. The product is a professionally built, radio control model. It is very important that you operate this model responsibly. Please read this instruction manual thoroughly and follow the directions. As a large model, the airplane is critical of proper battery use, control linkage setups and flying techniques. Please pay particular attention to the following areas. Maintain the proper mechanical advantage on all control surface linkages. Check the radio installation and make sure all the control surfaces are moving correctly (i.e. the correct direction and with the recommended throws). Test run the engine and make sure it transitions smoothly from idle to full throttle and back. Also ensure the engine is tuned according to the manufacturer s instructions, and it will run consistently and constantly at full throttle when adjusted. Check all the control horns, servo horns, and clevises to make sure they are secure and in good condition. Replace any items that would be considered questionable. Failure of any of these components in flight would mean the loss of your airplane. Never attempt to make full throttle dives! Large models perform much more like full-size airplane than small models. If the airframe goes too fast, such as in a high throttle dive, it may fail. The model should be flown like a full-scale airplane. Throttle management is absolutely necessary. Hardware checks Double-check the setscrews in all control horns to be sure they are very tight. Periodically check these to be sure they have not loosened over time. Always use threadlock on metal-to-metal fasteners. Receiver Battery Selection Be sure adequate batteries are used to power the receiver. It is recommended that two identical 6-volt receiver packs are used. Each pack must have a minimum of 2700mAh capacity. Use packs of 3000mAh when super high torque servos are used. Range check Always range check the radio system per the manufacturer's instructions before the initial test flight and periodically afterward. Check the voltage of the on-board packs ALWAYS use an ESV with a 1-amp load to check the receiver battery packs and the ignition pack before each and every flight. If there is any doubt that the packs are questionable, DO NOT FLY until the packs are recharged. Safety Precautions and Warnings This is a sophisticated hobby Product and not a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the Product or other property. This Product is not intended for use by children without direct adult supervision. The Product manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury. This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model, as this margin will help to avoid collisions or injury. Always operate your model in an open area away from cars, traffic, or people. Never operate the model into the street or populated areas for any reason. Never operate your model with low transmitter batteries. Carefully follow the directions and warnings for this and any optional support equipment (radio, engine, chargers, rechargeable battery packs, etc.) that you use. Keep all chemicals, small parts and anything electrical out of the reach of children. Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose. Limited Warranty & Limits of Liability We guarantee this kit to be free from defects in both material and workmanship at the date of purchase. 20 1

4 This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, or maintenance. This warranty is limited to the original purchaser and is not transferable. In no case shall our company s liability exceed the original cost of the purchased product and will not cover consequential, incidental or collateral damage. Our company reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of our company. Further, our company reserves the right to change or modify this warranty without notice. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. As our company has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of this product, you are advised to return this product immediately in new and unused condition to the place of purchase. Radio Setup A 7-channel or greater computer radio is highly recommended. This allows the following features: Mixing the right aileron to the left aileron (flaperon mix) Electronically adjustable aileron differential Mixing the right elevator to the left elevator (dual elevator mixing) Independent travel and trim adjustments of each elevator half Mixing the right rudder servo to the left rudder servo (not required when using a single rudder servo) When you use a 7-channel or greater computer radio, each servo is plugged into its own separate channel. Consult your radio manual for specific details on hookup and programming. Control Throws Contents of Kit AL50601 Fuselage for 50cc Sbach 342 AL50602 Fiberglass Painted Cowling for 50cc Sbach 342 AL50603 Canopy for 50cc Sbach 342 AL50604 Rudder for 50cc Sbach 342 AL50605 Left Wing Panel w/ Aileron for 50cc Sbach 342 AL50606 Right Wing Panel w/ Aileron for 50cc Sbach 342 AL50612 Left Stabilizer w/ Elevator for 50cc Sbach 342 AL50613 Right Stabilizer w/ Elevator for 50cc Sbach 342 AL50616 Landing Gear for 50cc Sbach 342 AL50617 Wheel Pants for 50cc Sbach 342 AL50620 Wing Tube for 50cc Sbach 342 AL50621 Stabilizer Tube for 50cc Sbach 342 AL50622 Decal Set for 50cc Sbach 342 The following is our recommended control throws for your reference. Aileron Standard 20 up 20 down 3D 40 up 40 down Elevator Recommended Center of Gravity (CG) Correctly balancing an aerobatic model is critical to its performance and flight characteristics. Checking the balance on this model is best done with two people. Rudder Standard 3D Standard 3D 15 up 40 up 26 left 43 left 15 down 40 down 26 right 43 right Measure back 30%-33% of the whole wing root s length from the leading edge and mark the CG range with a felt-tipped pen at the wing tip. This is the recommended center of gravity (CG) range. 2 19

5 Step 9 Install the switch for the ignition in the switch hatch on the side of the fuselage as shown. Additional Required Items 0 Secure the battery for the ignition inside the fuselage using a hook and loop strap. Make sure to add a few pieces of foam between the fuselage and battery to prevent damage to the battery caused by vibration. Connect the battery to the ignition switch. 1 Attach the fuel line from the fuel tank to the carburetor. Make sure the line is from the clunk and not the vent line. 2 Route the vent line from the fuel tank out of the bottom of the cowling. Radio Equipment 4-channel radio system (minimum) 1 standard servo for throttle 5 hi-torque servos Recommended Engines D-55, Q-50 Propeller (consult engine instructions) Servo Extensions Y-Harness Adhesives 6-minute epoxy 30-minute epoxy Thick CA glue Threadlock Tools Adjustable wrench (small) Drill (drill press preferred) Hook and loop straps Foam Hex wrench Hobby knife Phillips screwdriver (small) Pliers Scissors Square Measuring device (e.g. ruler, tape measure) 3 Make any necessary cutouts to clear the engine components in the cowling. Remove a section from the bottom of the cowling near the exhaust pipe for cooling outlet as shown. This opening is necessary to allow cooling air to pass through the cowling to prevent overheating of your engine. Servo Selection The servos used for the control surfaces of this model must have a minimum of 9kg-cm (125 oz-in) of servo torque. The servos with metal gear are strongly recommended. 4 Slide and lock the cowling to the fuselage and then secure the cowling using two screws. Mount the propeller and spinner to complete the procedure. Note: As the cowling mounting screw is inside the fuselage under the hatch, you need to open the hatch before accessing the screw. To open the hatch, just remove the screws holding it on both sides of the fuselage and lift the hatch from the fuselage. Before Starting Assembly Before beginning the assembly of the model, remove each part from its bag for inspection. Closely inspect the fuselage, wing panels, rudder, and stabilizer for damage. If you find any damaged or missing parts, contact the place of purchase. If you find any wrinkles in the covering, use a heat gun or covering iron to remove them. Use caution while working around areas where the colors overlap to prevent separating the colors. 18 3

6 Section 1 Aileron Servo Installation Wing panel ( left and right ) Locate the opening for the aileron servo at the bottom of the aileron. Carefully remove the covering from the opening using a hobby knife. The vertical and horizontal base lines are pre-marked on the firewall. Measure and mark the same distance from the lines for the four engine standoff screws. The firewall is already mounted correctly to provide right offset for the engine when the engine standoff center is on the intersection of the above lines. Drill the holes in the firewall for mounting the engine. Install four screws from the back side of the firewall. You may apply epoxy glue here. Plug a servo extension onto the servo. Tie the servo leads together by using a secure connector, or using a ribbon to prevent them from coming loose during flight. Tie a weight to a piece of string. A wheel collar works great in this application. Tie the other end of the string to the servo extension. Install engine using four machined aluminum standoffs, screws and lock washers. Step 6 Install throttle servo with servo arm to the provided throttle servo mount. Drill a hole in the firewall for the throttle linkage to pass. Attach the linkage to the servo arm and throttle. Lower the weight into the wing from the aileron servo opening. Let the weight drop out through the wing root for the servo. Use the string to pull the servo lead through the wing. Secure the servo using the hardware provided with the servo. Attach the servo arm to the servo. Make sure the servo arm is parallel with the hinge line when the servo is at the neutral position. Step 6 Repeat Steps 1 through 5 for the remaining wing panel. Step 7 Install the exhaust pipe to the engine. Step 8 Secure the ignition module to the engine box. Make the connections between the ignition box and engine at this time. 4 17

7 Wrap the receiver battery in foam and use rubber bands or hook and loop straps to secure the battery to the battery tray. Section 2 Aileron Control Horn Installation Assemble the fuel tank correctly. Be sure to use the gas-compatible stopper and fuel tubing. Place foam on the floor of the tank compartment. Secure the tank in place by wrapping rubber bands or hook and loop straps around the tank and tank floor. Later we will run the fuel lines. Wing panel (left and right) Aileron (left and right) Tape the aileron to the wing. Using a square held in alignment with the outer hole in the servo arm and 90 with the trailing edge of the wing, mark the aileron with a pen where the straight edge intersects the aileron hinge bevel. Locate the hidden switch hatch on the side of the fuselage and open the hatch. Mount the receiver switch in the hatch and then close the hatch door. Section 11 Mounting the Engine and Cowling Measure rearward 10mm (3/8 ) from the top of the aileron bevel and make another mark using a pen. The intersection of the line from and this line will be the position for the control horn. Remove the ailerons from the wing. Use rubbing alcohol to remove any tape residue. Engine and accessories This model accepts gas engines ranging from 50 through 60cc. The following steps show the installation of a 55cc gas engine for your reference. The detailed steps may be different when your selected engine is different. Carefully drill through the aileron at the marked position. Be especially careful when penetrating through the top surface of the aileron, as it s easy to split out the wood and rip the covering. Placing a wooden block under the aileron and drilling slowly will prevent these problems. D-55 Installation Collect the necessary items for the installation of your particular engine. Note: A hardwood block (hard point) is located below the sheeting; you will be drilling through this. Make sure to drill the hole perpendicular to the centerline of the aileron. 16 5

8 From the top of the aileron, plug the control horn screw through the hole and secure it with the provided nut. Step 6 Repeat Steps 1 through 5 for the remaining aileron. Install the following items onto the axle: washer, wheel and then wheel collar. Note: It may be necessary to drill the hole in the wheel to fit onto the axle. Section 3 Hinging and Sealing the Control Surfaces Wing panel ( left and right ) Aileron (left and right) Properly hinging the control surfaces on this model is very important! Poorly installed hinges affect the model s precision and control response and can also be dangerous. Each and every hinge needs to be securely bonded in place in both the flying surface and the control surface. The hinge pivot points need to be exactly parallel to each other and precisely located on the center of the hinge line. The control surfaces of this model are predrilled for the hinges included in hardware package. Sand each end of the hinges using coarse sandpaper. This will improve the bond of the epoxy to the hinge. Mix some 30-minute epoxy. Using a glue syringe or toothpick, place a sufficient amount of the epoxy into one of the hinge pockets in the aileron leading edge. Install one of the hinge points until the hinge pin center is flush with the leading edge of the aileron. Wipe away any excess epoxy with rubbing alcohol. Continue installing hinges in the leading edge of the aileron. The control surfaces (ailerons) will be installed after the epoxy is fully cured. Note: Be sure that the hinge pivot pins are parallel and flush to the aileron leading edge. It s important to frequently mix a fresh batch of 30-minute epoxy in order to achieve good glue joint penetration. If you notice the epoxy becoming thicker, then mix a new batch! The blind nuts on the wheel pant are pre-installed. Slide the wheel pant to the right position on the wheel. Secure the wheel pant to the landing gear with two screws. Note: Always use threadlock on metal-to-metal fasteners to prevent them from vibrating loose. Install the landing gear to the fuselage using four screws and four lock washers. Repeat Steps 1 through 4 for the remaining landing gear. Section 10 Receiver, Battery and Fuel Tank Installation Use foam and rubber bands (or hook and loop straps) to secure the receiver to the battery tray. 6 15

9 Remove the bracket and drill pilot holes at the previously marked positions. Assemble the tail wheel bracket and use provided screws to secure the bracket in place. A hardwood plate is positioned in the rear of the fuselage, allowing these screws to be firmly tightened. Hint: Remove the screws and wick thin CA into the holes to strengthen the threads. Then, reinstall the screws. Using the provided springs, hook up the tiller arm to the rudder with the tail wheel. When the epoxy is cured, work each hinge throughout its full motion several times using your hands. This will break free any epoxy that may have found its way into the hinge joint. Move the hinge throughout its full travel until no resistance is felt. Mix some 30-minute epoxy. Place a sufficient amount of epoxy in each of the hinge pockets in one wing panel. Carefully attach the aileron to the wing, making sure the hinges are inserted in their respective hinge pockets. Press the aileron and wing together until the hinge line gap between the aileron and wing is small enough. Use a paper towel and rubbing alcohol to wipe away any visible epoxy around the hinges. Step 6 Double-check the hinge gap and allow the epoxy to fully cure for enough time. Now is a good time to repeat Steps 1 through 5 for the remaining wing panel and aileron. Step 7 When fully cured, move each control surface throughout its travel range several times to break away any epoxy in the hinge. Be sure to deflect the surface fully. Note: It s a good idea to seal the aileron and elevator hinge lines airtight with a piece of covering to prevent flutter after you finish hinges installation. Section 9 Landing Gear Installation Main landing gear Wheel (2) Wheel pant (left and right) Install the axles in the landing gear. Secure the axles using an adjustable wrench and the nuts provided with the axles. Section 4 Aileron Linkage Installation Control horn linkages (2) Screw the molded swivel link with linkage onto the control horn screw until the distance from the aileron surface to the top of the link is 28mm (1 1/8 ). 14 7

10 Adjust the linkage length until the hole in the ball link aligns with the outer hole in the servo arm when the aileron is neutral and the servo arm is centered. Attach the ball link to the outer hole in the servo arm with a screw and nut as shown. Don t forget to use threadlock. Step 7 Hinge the rudder using the same techniques as with the aileron and elevator. Step 8 Put the rudder in its neutral position and center the rudder servo. Adjust the length of both rudder cables to match the distance from the rudder servo arm to the control horn. Use a plier to fix the length of the cables. Install the cables on both sides of the outer holes of the rudder servo arm and control horn. Repeat Steps 1 through 3 for the remaining servo in the opposite wing panel. Section 5 Wing Installation Wing panels Wing tube Check the opening for the wing tube, servo leads and pins from inside of the fuselage where the wing panels connect to the fuselage. Carefully remove the covering from the opening using a hobby knife. Locate the wing tube and carefully slide it into one wing panel as deeply as possible. Slide the wing (with tube) into the wing tube opening in the fuselage. Pass the servo lead in the wing into the fuselage before the wing connects to the fuselage. Make sure the wing panel anti-rotation pins slide into the holes provided in the fuselage. Note: It may be necessary to slightly enlarge the holes in the fuselage for the anti-rotation pins using a small round file. Section 8 Tail Wheel Installation Rudder Tail wheel assembly Install the tiller arm to the bottom of the rudder with screws. Position the tail wheel in place as shown, centered on the rear of the fuselage. Using a felt-tipped pen, mark the positions for the mounting screws through the tail wheel bracket. 8 13

11 Install the rudder servo on the right position of servo tray in the fuselage. Attach the servo arm to the servo. Make sure the servo arm is perpendicular (90 ) to the centerline of the fuselage when the servo is at the neutral position. Put the fuselage on its side with rudder virtually connecting. Using the provided rudder cable, measure a straight line from the rudder servo arm to the opening in, and mark the extension line on the rudder with a pen. Measure rearward 10mm (3/8 ) from the edge of the rudder bevel and make another mark using a pen. The intersection of the line from and this line will be the position for the rudder control horn. Carefully drill through the rudder at the marked position, perpendicular (90 ) to the rudder centerline at the marked position. Be especially careful when penetrating through the backside of the rudder. Step 6 Put the threaded rod of the rudder control horn through the hole and secure it with the provided nuts. Adjust the position of the rod so that it has the same length on both sides of the rudder. Screw the molded swivel link with linkage onto the threaded rod at the right position so that the rudder cable in operation will not hit the opening of the fuselage. Carefully slide the remaining wing panel onto the wing tube that projects from the fuselage. The fit may be tight; use caution when inserting the wing panels onto the wing tube and fuselage. Make sure both wings fit well with the fuselage and there is no gap between them. Secure the wing panels using the provided wing screws. Section 6 Stabilizer Installation Stabilizer (left and right) Stabilizer tube Locate the opening for the elevator servo arm at the bottom of the stabilizer. Carefully remove the covering from the opening using a hobby knife. Install the elevator servo using the hardware provided with the servo as shown. Plug a servo extension onto the servo. 12 9

12 Center the elevator servo using the radio system. Install a servo arm onto the servo. Note: The technique for installing the control horns in the elevators is similar to the aileron control horn installation. Step 8 Glue the elevator hinges in place using the same techniques used to hinge the ailerons. The shortened hinges will be installed into the stabilizer towards the root. Mark a line 3mm (1/8 ) away from the servo arm and parallel to the movement direction of the servo arm. Measure rearward 10mm (3/8 ) from the top of the elevator bevel and make another mark using a pen. The intersection of the two marks will be the position for the control horn. Carefully drill through the elevator at the marked position. Be especially careful when penetrating through the top surface of the elevator, as it s easy to split out the wood and rip the covering. Placing a wooden block under the elevator and drilling slowly will prevent these problems. Step 9 Install the elevator linkage using the same techniques used to the aileron linkage. 0 Repeat Steps 1 through 9 for the remaining stabilizer and elevator. 1 Install the stabilizer using the same techniques for the wing installation. Secure the stabilizer with screws at the bottom as shown. Note: Make sure to drill the hole perpendicular to the centerline of the elevator. Step 6 From the top of the elevator, plug the control horn screw through the hole and secure it with the provided nut. Section 7 Rudder Installation Step 7 Cut off the first section of one of the hinges. This is done to clear the tube installed in the stabilizer. Rudder Check the opening for the rudder cable in the fuselage. Carefully remove the covering from the opening using a hobby knife

F3D-30 ARF ASSEMBLY MANUAL

F3D-30 ARF ASSEMBLY MANUAL F3D-30 ARF ASSEMBLY MANUAL This Manuel is the sole property of Kangke Industrial USA, Inc. Reproducing any part without the consent of Kangke Industrial USA, Inc. is a lawful violation. Kangke Industrial

More information

EXTRA 330LX. Specifications: Code: SEA274. Graphics and specifications may change without notice. ASSEMBLY MANUAL

EXTRA 330LX. Specifications: Code: SEA274. Graphics and specifications may change without notice. ASSEMBLY MANUAL ASSEMBLY MANUAL EXTRA 330LX Code: SEA274 Graphics and specifications may change without notice. Specifications: Wingspan---------------82.0 in (208.2 cm). Wing area---------------1349.4 sq.in ( 87.1 sq.dm).

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum

More information

ALMOST READY TO FLY. Wing Span in cm. 2

ALMOST READY TO FLY. Wing Span in cm. 2 ASSEMBLY MANUAL ALMOST READY TO FLY MS: X12 A - B Graphics and specfications may change without notice. Kit features. Specifications Wing Span ------------------------------- 42.7 in ---------------------

More information

I n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION

I n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2

More information

ALMOST READY TO FLY. Wing Span in cm. 2

ALMOST READY TO FLY. Wing Span in cm. 2 ASSEMBLY MANUAL ALMOST READY TO FLY MS:X9 Specifications Wing Span --------------------------61.4 in ---------------------------156cm. 2 Wing Area --------------------------606.1 sq.in ------------------

More information

Aviator Pro 120 ARF. Instruction Manual. Specifications

Aviator Pro 120 ARF. Instruction Manual. Specifications Aviator Pro 120 ARF Instruction Manual Specifications Wingspan: 110 in (2800 mm) Length: 74 in (1870 mm) Wing Area: 1581sq in (102 sq dm) Weight: 11.4-13.4 lbs (5190-6100 g) Dear Customer, Congratulations

More information

MARACANA ASSEMBLY INSTRUCTION .40 ARF LOW WING TRAINER RADIO CONTROL MODEL. Every body can fly

MARACANA ASSEMBLY INSTRUCTION .40 ARF LOW WING TRAINER RADIO CONTROL MODEL. Every body can fly RADIO CONTROL MODEL ASSEMBLY INSTRUCTION MARACANA.40 ARF LOW WING TRAINER Every body can fly VQA085 EP GP You can use both Gas or Electric power Wingspan: 59in.(1520mm) Fuselage length: 48in.(1220mm) Engine:

More information

51in Aerobatic Series Sukhoi SU-26M Almost-Ready-to-Fly. Instruction Manual. Specifications

51in Aerobatic Series Sukhoi SU-26M Almost-Ready-to-Fly. Instruction Manual. Specifications 51in Aerobatic Series Sukhoi SU-26M Almost-Ready-to-Fly Instruction Manual Specifications Wingspan: 51.2 in (1300mm) Length: 51.2 in (1300mm) Wing Area: 581 sq in (37.5sq dm) Flying Weight: 3.5 lb (1600g)

More information

Table of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03

Table of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03 Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator

More information

96in Super Decathlon ARF

96in Super Decathlon ARF 96in Super Decathlon ARF Instruction Manual Specifications Wingspan: 96in (2438mm) Length: 63.5 in (1614mm) Weight: Approx. 13lbs (6.5kg) 1 Dear Customer, Congratulations on your purchase of Super Decathlon

More information

FUN-50 ARF ASSEMBLY MANUAL

FUN-50 ARF ASSEMBLY MANUAL FUN-50 ARF ASSEMBLY MANUAL This Manuel is the sole property of Kangke Industrial USA, Inc. Reproducing any part without the consent of Kangke Industrial USA, Inc. is a lawful violation. Kangke Industrial

More information

48in Sbach-342. Instruction Manual. Specifications

48in Sbach-342. Instruction Manual. Specifications 48in Sbach-342 Instruction Manual Specifications Wingspan: 48in (1219mm) Length: 46in (1163mm) Wing Area: 471sq in (30.4sq dm) Flying Weight: 1.8-2.0lb (800-900g) Dear Customer, www.valuehobby.com/48in-s342-arf.html

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 6000mm (236.2 in) - Length: 2873mm (113.1 in) - Flying weight: 14-18 kg - Wing area: 219.4 dm2 - Wing loading: 64g/dm2 - Wing type: HQ airfoils - Covering type: Genuine ORACOVER

More information

Instruction Manual BULLDOG. Wingspan : 1410 mm (55.5in) : 1450 mm (57.1in) : 4900gr gr. Weight. : 6-9 Channel/ 7 servo high torque, 1standard

Instruction Manual BULLDOG. Wingspan : 1410 mm (55.5in) : 1450 mm (57.1in) : 4900gr gr. Weight. : 6-9 Channel/ 7 servo high torque, 1standard Wingspan : 1410 mm (55.5in) Length Weight Radio Engine : 1450 mm (57.1in) : 4900gr - 5600gr : 6-9 Channel/ 7 servo high torque, 1standard : 1.20/ 2 stroke 1.80/ 4 stroke KIT CONTENTS: We have organized

More information

Instruction Manual book

Instruction Manual book book SPECIFICATION Wingspan : 1,450 mm 57.09 in. Length : 1,200mm 47.24in. Weight : 3.1 kg 6.82 Lbs. Radio : 05 channels. Servo : 07 servos. Engine : 61-75 2 stroke. 91 4 stroke. Made in Vietnam. This

More information

MS:183 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:183 ASSEMBLY MANUAL. Graphics and specifications may change without notice. MS:183 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------79.9in (203cm). Wing area -----------------1165.6sq.in (75.2sq dm).

More information

INSTRUCTION MANUAL BOOK

INSTRUCTION MANUAL BOOK INSTRUCTION MANUAL BOOK ITEM CODE BH57. SPECIFICATION Wingspan: 1,470 mm. 57.87 in. Length : 1,180 mm. 46.46 in. Weight : 2.7 Kg. 5.94 Lbs. Engine : 46 cu.in 2 stroke. 52 cu.in 4 stroke. Radio : 4 channels.

More information

SK-50 ARF ASSEMBLY MANUAL

SK-50 ARF ASSEMBLY MANUAL SK-50 ARF ASSEMBLY MANUAL Kangke Industrial USA, Inc. 65 East Jefryn Blvd. Deer Park NY 11729 http://www.kangkeusa.com E-mail: info@kangkeusa.com Tel: 1-877-203-2377 Fax: 1-631-274-3296 Congratulations!

More information

YAK-55M 1.8. Forget the rest - a YAK ist the best! Assembly instructions. Gernot

YAK-55M 1.8. Forget the rest - a YAK ist the best! Assembly instructions. Gernot YAK-55M 1.8 Assembly instructions Forget the rest - a YAK ist the best! Gernot Table of contents 1.Specifications (metric units)...2 2.Recommended Setups...2 3.Required tools and adhesives:...2 4.Warning...3

More information

JUNKERS CL1 G-BUYU. Specifications: Code: SEA275. Graphics and specifications may change without notice. ASSEMBLY MANUAL

JUNKERS CL1 G-BUYU. Specifications: Code: SEA275. Graphics and specifications may change without notice. ASSEMBLY MANUAL ASSEMBLY MANUAL JUNKERS CL1 G-BUYU Code: SEA275 Graphics and specifications may change without notice. Specifications: Wingspan---------------68.9 in (175 cm). Wing area---------------776.6 sq.in ( 50.1

More information

MS:176 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:176 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:176 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------98.4in (250cm). Wing area ----------------1576.4sq.in (101.7sq dm).

More information

WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL Graphics and specifications may change without notice. Code: SEA232 Specifications: Wingspan---------------70.9 in (180 cm). Wing area---------------810.3 sq.in (52.3

More information

WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL Code: SEA238 Graphics and specifications may change without notice. Specifications: Wingspan---------------68.9 in (175 cm). Wing area---------------776.6 sq.in (

More information

Radio control model INSTRUCTION MANUAL PYLON RACING. Wingspan: 1148mm (45.2 ) Radio : 4 channels Engine : two-stroke

Radio control model INSTRUCTION MANUAL PYLON RACING. Wingspan: 1148mm (45.2 ) Radio : 4 channels Engine : two-stroke VQA038 VQA039 Radio control model INSTRUCTION MANUAL MAGIC PYLON RACING Wingspan: 1148mm (45.2 ) Radio : 4 channels Engine :.25 -.32 two-stroke WARNING! This radio control model is not a toy. If modified

More information

Instruction Manual. Wingspan : 1400 mm (55.12 inch) : 1480 mm (58.27 inch) : 5500gr gr. : 6-9 channel/ 8 servo high torque,1 standard

Instruction Manual. Wingspan : 1400 mm (55.12 inch) : 1480 mm (58.27 inch) : 5500gr gr. : 6-9 channel/ 8 servo high torque,1 standard Wingspan : 1400 mm (55.12 inch) g Length : 1480 mm (58.27 inch) Weight : 5500gr - 6000gr Radio : 6-9 channel/ 8 servo high torque,1 standard Engine : GT 22 OS KIT CONTENTS: We have organized the parts

More information

MS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:159 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------61.8in (157cm). Wing area -----------------1100.5sq.in (71.0sq dm). Weight

More information

I/C FLIGHT GUIDELINES

I/C FLIGHT GUIDELINES SPECIFICATION - Wingspan: 3500mm (137.8 in) - Length: 1650mm (64.96 in) - Flying weight: 3700-4000 gr - Wing area: 75 dm2 - Wing loading: 49g/dm2 - Wing type: HQ profile - Covering type: Genuine ORACOVER

More information

ASSEMBLY MANUAL SIZE

ASSEMBLY MANUAL SIZE SIZE.75 -.91 ASSEMBLY MANUAL MS:123 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------66.9in (170cm). Wing area -----------------761.1sq.in (49.1sq

More information

1100MM P-51 Mustang ELECTRIC POWERED REMOTE CONTROL AIRPLANE ELEVENHOBBY.COM

1100MM P-51 Mustang ELECTRIC POWERED REMOTE CONTROL AIRPLANE ELEVENHOBBY.COM 1100MM P-51 Mustang ELECTRIC POWERED REMOTE CONTROL AIRPLANE ELEVENHOBBY.COM WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to

More information

Instruction Manual. Wingspan : 2270mm (89.37 inches) : 1870mm (73.62 inches) : 7400gr gr. : 4 channel - 6 standard servo.

Instruction Manual. Wingspan : 2270mm (89.37 inches) : 1870mm (73.62 inches) : 7400gr gr. : 4 channel - 6 standard servo. Wingspan : 2270mm (89.37 inches) g Length : 1870mm (73.62 inches) Weight : 7400gr - 7600gr Radio : 4 channel - 6 standard servo Engine : 25cc-35cc KIT CONTENTS: We have organized the parts as they come

More information

Instruction Manual book

Instruction Manual book Instruction Manual book SPECIFICATION Wingspan : 1,800mm. 70.87 in. Length : 1,350 mm. 53.15in. Weight : 3.6kg. 7.92lbs. Parts Listing required (not included). Glow Engine : 55-61 2 stroke. 91 4 stroke.

More information

: 7 channel - 9 servo, Hi-Torque ( Minimum 6 kg ).

: 7 channel - 9 servo, Hi-Torque ( Minimum 6 kg ). g Wingspan : 1820mm (71.65 inches) Length : 1625mm (63.98 inches) Weight : 6900gr Engine : 25cc - 35cc Radio : 7 channel - 9 servo, Hi-Torque ( Minimum 6 kg ). KIT CONTENTS: We have organized the parts

More information

: 6 channel - 9 servo

: 6 channel - 9 servo g Wingspan : 2005mm (78.94 inches) Length : 1640mm (64.57 inches) Weight : 6400g - 6600g Engine : 25cc - 35cc Radio : 6 channel - 9 servo KIT CONTENTS: We have organized the parts as they come out of

More information

1660mm (65.4 in) 1200mm (47.2 in) 2700gr gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke

1660mm (65.4 in) 1200mm (47.2 in) 2700gr gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke Instruction Manual CESSNA-46 1660mm (65.4 in) 1200mm (47.2 in) 2700gr - 3000gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke KIT CONTENTS: We have organized the parts as they come out of the

More information

MS:174 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:174 ASSEMBLY MANUAL. Graphics and specifications may change without notice. MS:174 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------79.9in (203cm). Wing area -----------------911.4sq.in (58.8sq dm).

More information

SIZE 55 ASSEMBLY MANUAL

SIZE 55 ASSEMBLY MANUAL SIZE 55 ASSEMBLY MANUAL MS:120 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------63in (160cm). Wing area -----------------643.3sq.in (41.5sq

More information

MS:160 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:160 ASSEMBLY MANUAL. Graphics and specifications may change without notice. MS:160 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------70.9in (180cm). Wing area -----------------613.8sq.in (39.6sq dm).

More information

SIZE.120 OR 30CC SCALE 1:5 ARF

SIZE.120 OR 30CC SCALE 1:5 ARF PC21 PILATUS MK2 SIZE.120 OR 30CC SCALE 1:5 ARF SPECIFICATION - Wingspan: 1772mm (69.72in) - Length: 2019mm (79.5 in) - Flying weight: 6.4-7.2 kg - Wing area: 57.6 dm2 - Wing loading: 113g/dm2 - Wing type:

More information

ARF TRAINER KIT ASSEMBLY MANUAL BOOMERANG EP. ALMOST READY TO FLY

ARF TRAINER KIT ASSEMBLY MANUAL BOOMERANG EP.  ALMOST READY TO FLY WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL BOOMERANG EP ARF TRAINER KIT Graphics and specifications may change without notice. MS: 211 ALMOST READY TO FLY Specifications: Wingspan---------------56.0 in (142.2

More information

MS:167 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:167 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:167 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------66.9in (170cm). Wing area -----------------764.2sq.in (49.3sq dm).

More information

ASSEMBLY MANUAL

ASSEMBLY MANUAL www.seagullmodels.com MS: X104 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ----------------- 35.4in (90.0cm). Wing area ------------------392.2sq.in

More information

ASSEMBLY MANUAL SIZE: 46-62

ASSEMBLY MANUAL SIZE: 46-62 SIZE: 46-62 MS:199 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------54.9 in ( 139.5cm). Wing area -----------------517.7 sq.in

More information

WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL Graphics and specifications may change without notice. Code: SEA240 (SEA240M) (SEA240Y) Specifications: www.seagullmodels.com Wingspan---------------74.8 in (190 cm).

More information

ASSEMBLY MANUAL. Specifications

ASSEMBLY MANUAL. Specifications Kit features. Ready-made minimal assembly & finishing required. Ready-covered covering. Photo-illustrated step-by-step Assembly Manual. ASSEMBLY MANUAL Specifications Wingspan--------------------------------

More information

8mm EPP Acrocub. Instruction Manual. Specifications

8mm EPP Acrocub. Instruction Manual. Specifications 8mm EPP Acrocub Instruction Manual Specifications Wingspan: 34.6 in (880mm) Length: 31.5 in (800mm) Wing Area: 213.9 sq in (13.8sq dm) Flying Weight: Approx. 9oz (270g) Dear Customer, www.valuehobby.com/8mm-epp-acrocub.html

More information

Instruction Manual book

Instruction Manual book book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. This instruction manual

More information

Instruction Manual. Wingspan : 1400mm (55.12 in) : 1370mm (53.94 in) : 2600gr gr. : 4 channel / 5 servo. : / 2 stroke_52-71 / 4 stroke

Instruction Manual. Wingspan : 1400mm (55.12 in) : 1370mm (53.94 in) : 2600gr gr. : 4 channel / 5 servo. : / 2 stroke_52-71 / 4 stroke Instruction Manual 540 Wingspan : 1400mm (55.12 in) g Length : 1370mm (53.94 in) Weight : 2600gr - 2800gr Radio : 4 channel / 5 servo Engine : 46-52 / 2 stroke_52-71 / 4 stroke KIT CONTENTS: We have organized

More information

(Glider) ASSEMBLY MANUAL

(Glider) ASSEMBLY MANUAL (Glider) MS:132 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------118.1in (300cm). Wing area ---------------------902.1sq.in

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 1410mm (55.5 in) - Length: 1278mm (50.3 in) - Flying weight: 3.2-3.4 kg - Wing area: 41.3 dm2 - Wing loading: 75g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

ASSEMBLY MANUAL. Graphics and specifications may change without notice.

ASSEMBLY MANUAL. Graphics and specifications may change without notice. NEMESISMS: SEA 111 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications Wing span------------------------------------- 55.9in ------------------------------- 142cm. Wing

More information

AVIATOR 25 ARF Almost Ready-to-Fly

AVIATOR 25 ARF Almost Ready-to-Fly AVIATOR 25 ARF Almost Ready-to-Fly Instruction Manual Specifications Wingspan: 54.3 in (1380mm) Length: 45.2 in (1150mm) Wing Area: 438 sq in (34sq dm) Flying Weight: 3.8 b (1700g) Dear Customer, Congratulations

More information

WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL Graphics and specifications may change without notice. Code: SEA231 Specifications: Wingspan---------------80 in (203.2 cm). Wing area---------------1235.4 sq.in (79.7

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 1800mm (70.8 in) - Length: 1355mm (53.3 in) - Flying weight: 4100-4300 g - Wing area: 51 dm2 - Wing loading: 80g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

RADIO CONTROL MODEL HURRICANE

RADIO CONTROL MODEL HURRICANE RADIO CONTROL MODEL VQAA040G VQAA040B HURRINE Almost ready to fly SPECIFITIONS Wingspan...63 in. / 161cm Length...50 in. / 129cm Engine...50~60 2T / 70~90 4T Or Electric equivalent. RC Functions: Motor

More information

MS:190 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:190 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:190 Graphics and specifications may change without notice. Specifications: Wing span -----------------------------49.2.in (125cm). Wing area -----------------415.4sq.in (26.8sq dm).

More information

MS:124 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:124 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:124 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------65in (165cm). Wing area -----------------658.8sq.in (42.5sq dm). Weight

More information

WE GET PEOPLE FLYING T-34

WE GET PEOPLE FLYING T-34 TM WE GET PEOPLE FLYING T-34 Mentor ASSEMBLY MANUAL Specifications Wingspan:... 57.25 in (1454 mm) Length:... 45 in (1146 mm) Wing Area:... 555 sq in (35.8 sq dm) Weight:... 6 7 lb (2.7 kg 3.2 kg) Radio:...

More information

ASSEMBLY MANUAL. Specifications

ASSEMBLY MANUAL. Specifications MS:56H Kit features. Specifications Wingspan ------------------------------ 63 in -------------------------- 160cm. Wing area ----------------------------- 728 sq.in ------------------ 47 sq.dm. Weight

More information

SBACH SCALE 1:4 ½ ARF

SBACH SCALE 1:4 ½ ARF SPECIFICATION - Wingspan: 1663mm (65.5 in) - Length: 1638mm (64.5 in) - Flying weight: 4700-5200 gr - Wing area: 56 dm2 - Wing loading: 85g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

Instruction Manual. Wingspan : 1884 mm (74.17 in) Length. Weight. Engine. : 4 channels / 5 servo standard. : 1450 mm (57.

Instruction Manual. Wingspan : 1884 mm (74.17 in) Length. Weight. Engine. : 4 channels / 5 servo standard. : 1450 mm (57. Wingspan : 1884 mm (74.17 in) Length : 1450 mm (57.09 in) Weight : 4000 gr Engine : 60 two strokes Radio : 4 channels / 5 servo standard KIT CONTENTS: We have organized the parts as they come out of the

More information

STICK F Class 60 Class INSTRUCTION MANUAL. Or Electric equivalent. (2T engine) (4T engine) Radio control model SPECIFICATIONS

STICK F Class 60 Class INSTRUCTION MANUAL. Or Electric equivalent. (2T engine) (4T engine) Radio control model SPECIFICATIONS Radio control model 45 Class 60 Class (2T engine) (4T engine) Or Electric equivalent INSTRUCTION MANUAL STICK F - 1500 SPECIFICATIONS Wingspan 60 in. Length 38.5 in. Electric Motor 650 Watt Glow Engine.45

More information

RADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS. Wasp

RADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS. Wasp RADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS Wasp TRAINER Almost ready-to-fly Wingspan 1520mm Fuselage length 1105mm Engine: 40-46 2T / 52-60 4T Electric Motor: 600-700W Radio: 5 channel / 4-5 servo RC Functions:

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 2000mm (78.7in) - Length: 1544mm (60.7 in) - Flying weight: 3600-3800 gr - Wing area: 66 dm2 - Wing loading: 55g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

SebArt professional line

SebArt professional line SebArt professional line Sebart 30E ARF ASSEMBLY MANUAL The new Sebart 30E ARF was designed by Italy aerobatic pilot Sebastiano Silvestri, it is the replica of a new real full-scale aerobatic plane. This

More information

SebArt professional line

SebArt professional line SebArt professional line Sebart 30E ARF ASSEMBLY MANUAL The new Sebart 30E ARF was designed by Italy aerobatic pilot Sebastiano Silvestri, it is the replica of a new real full-scale aerobatic plane. This

More information

Instruction Manual. Specification:

Instruction Manual. Specification: Instruction Manual L O W Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1790gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo W I N G KIT CONTENTS: We have

More information

ARF. Specifications: ASSEMBLY MANUAL MS: 193. Graphics and specifications may change without notice.

ARF.   Specifications:   ASSEMBLY MANUAL MS: 193. Graphics and specifications may change without notice. ASSEMBLY MANUAL Graphics and specifications may change without notice. MS: 193 ARF Specifications: Wingspan---------------62.0 in (157.5 cm). Wing area----------------620 sq.in (40.0 sq.dm). Weight-------------------3.3-3.9

More information

MS:136 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:136 ASSEMBLY MANUAL. Graphics and specifications may change without notice. ASSEMBLY MANUAL MS:136 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------79.5in (202cm). Wing area -----------------965.7sq.in (62.3sq dm). Weight

More information

Instruction Manual book

Instruction Manual book book SPECIFICATION Wingspan : 2,080 mm 81.89 in. Length : 1,680 mm 66.14 in. Weight : 6.2 kg 13.64 Lbs. Radio : 06 channels. Servo : 06 servos. Engine : 30-35 CC Gas(FUJI IMVAC). Made in Vietnam. This

More information

CAP 232 ASSEMBLY MANUAL

CAP 232 ASSEMBLY MANUAL CAP 232 MS: ASSEMBLY MANUAL SEA 91 Graphics and specfications may change without notice. Specifications Wingspan------------------------------------ 65 in --------------------------------- 165cm. Wing

More information

MS:158 ASSEMBLY MANUAL. Graphics and specifications may change without notice.

MS:158 ASSEMBLY MANUAL. Graphics and specifications may change without notice. MS:158 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------70.9in (180cm). Wing area -----------------644.8sq.in (41.6sq dm).

More information

Very Fun & Easy NOTICE

Very Fun & Easy NOTICE Very Fun & Easy NOTICE NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of our company. For up-to-date product literature, Visit our website

More information

HERO 3D SCALE 1:6 ARF

HERO 3D SCALE 1:6 ARF Instruction Manual SPECIFICATION - Wingspan: 1500mm(59 in) - Length: 1410mm (55.5 in) - Flying weight: 2100-2300 gr - Wing area: 58 dm2 - Wing loading: 39g/dm2 - Covering type: Genuine ORACOVER - Gear

More information

Specifications. Kit features.

Specifications. Kit features. A S S E M B L Y M A N U A L MS:58 Graphics and Specfications may change without notice. Specifications Wingspan---------------------------------------- 70.9 in---------------------------- 182cm. Wing area----------------------------------------

More information

Specifications: Instruction Manual. Graphics and specifications may change without notice. ASSEMBLY MANUAL. Code : SEA237

Specifications: Instruction Manual. Graphics and specifications may change without notice. ASSEMBLY MANUAL. Code : SEA237 ASSEMBLY MANUAL Instruction Manual. Graphics and specifications may change without notice. Code : SEA237 Specifications: Wingspan---------------61 in ( 155 cm). Wing area---------------1023 sq.in ( 66

More information

Instruction Manual book

Instruction Manual book Instruction Manual book SPECIFICATION Wingspan : 2,170 mm 85.43 in. Length : 1,760 mm 69.29 in. Weight : 6.3 kg 13.86 Lbs. Radio : 06 channels. Servo : 08 servos. Engine : 45-50CC Gas. Made in Vietnam.

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 2190mm (86.2 in) - Length: 1907mm (75 in) - Flying weight: 9000-12000 gr - Wing area: 92 dm2 - Wing loading: 98g/dm2 - Wing type: Naca airfoils - Retract gear type: Air-retract

More information

YAK54 MK2. GP/EP size.120/20cc SCALE 1:4 ¾ ARF. Instruction Manual. version. version

YAK54 MK2. GP/EP size.120/20cc SCALE 1:4 ¾ ARF. Instruction Manual. version. version Instruction Manual GP EP version version GP/EP size.10/0cc SCALE 1:4 ¾ ARF SPECIFICATION - Wingspan: 168 (66.3 in) - Length: 1605mm (63.1 in) - Flying weight: 4700-500 gr - Wing area: 54.7 dm - Wing loading:

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 1420mm (55.91 in) - Length: 1370mm (53.94 in) - Flying weight: 2600-2800 gr - Wing area: 41.6 dm2 - Wing loading: 65g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

ASSEMBLY MANUAL

ASSEMBLY MANUAL ASSEMBLY MANUAL MS: 254 Graphics and specifications may change without notice. MS: 254 ALMOST READY TO FLY Specifications: www.seagullmodels.com Wingspan---------------70.9 in (180 cm). Wing area---------------793.9

More information

RECOMMENDED MOTOR AND BATTERY SET UP

RECOMMENDED MOTOR AND BATTERY SET UP SPECIFICATION - Wingspan: 1669mm (65.7in) - Length: 1229mm (48.43 in) - Flying weight: 3300-3400 gr - Wing area: 44.2 dm2 - Wing loading: 67g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER

More information

Instruction Manual book

Instruction Manual book Instruction Manual book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. JU87-STUKA

More information

Assembly Manual For. Wingspan: 88 in Wing area: sp in Length: 78.8 in Engine: 50CC.

Assembly Manual For. Wingspan: 88 in Wing area: sp in Length: 78.8 in Engine: 50CC. Assembly Manual For Wingspan: 88 in Wing area: 1479.8 sp in Length: 78.8 in Engine: 50CC www.pilot-rc.com INTRODUCTION Thank you for purchasing our new 50 cc model. We strive to bring you the most complete

More information

to fly. Most hardware included and all replacement parts are available.

to fly. Most hardware included and all replacement parts are available. Instruction Manual The Thunderbolt P47 was perhaps the greatest of world war II in terms of all round performance and capability Phoenix Model has recreated a 2C - 60 class engine (or 4c 91 class) It was

More information

ASSEMBLY MANUAL. Kit features. MS:76

ASSEMBLY MANUAL. Kit features. MS:76 ASSEMBLY MANUAL MS:76 Graphics and specfications may change without notice. Specifications: Wingspan---------------------------------------------------- 82.8 in------------------------------------- 210.3cm.

More information

SebArt professional line

SebArt professional line SebArt professional line Wind S PRO 2m ARF ASSEMBLY MANUAL The new Wind S PRO ARF was designed by Italy aerobatic pilot, Sebastiano Silvestri. This professional ARF kit is the result of Sebastiano s 20

More information

SebArt professional line

SebArt professional line SebArt professional line Mini L39 1,46m ARF 90mm EDF-6S or P20-K30 turbine ASSEMBLY MANUAL The all new L39 Jet ARF was designed by Italy aerobatic pilot Sebastiano Silvestri. This sport ARF jet-model design

More information

WWW.SEAGULLMODELS.COM A S S E M B L Y M A N U A L Graphics and specifications may change without notice. Code : SEA255 Specifications: www.seagullmodels.com Wingspan---------------70.9 in (180 cm). Wing

More information

Instruction Manual book

Instruction Manual book Instruction Manual book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. JU87-STUKA

More information

LASER 200. Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL

LASER 200. Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL LASER 200 Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL SPECIFICATIONS: WING SPAN ----------------------------------------175CM -------------------------------- 68.75 in. WING AREA ------------------------------------------4746CM2

More information

Neptune Seaplane25 ARF. Instruction Manual. Specifications

Neptune Seaplane25 ARF. Instruction Manual. Specifications Neptune Seaplane25 ARF Instruction Manual Specifications Wingspan: 1270mm (50in) Length: 1155mm (45.5in) Wing Area: 34.8 sq dm (539.4 sq in) Weight: 1950g (4.30lbs) Product Highlights Removable hatch on

More information

MEMO. No.4341 Specification: Wing Span: 29.1 (740mm) Length: 36.6 (930mm) 2. Warranty

MEMO. No.4341 Specification: Wing Span: 29.1 (740mm) Length: 36.6 (930mm) 2. Warranty MEMO No.4341 Specification: Wing Span: 29.1 (740mm) Length: 36.6 (930mm) 2 Wing Area: 299 sq.in. (19.29 dm ) Weight: 18.9oz. (536.5g) 2 Wing loading: 0.58 oz./sq.ft (27.8g/dm ) Motor: OBL 29/27-07A Warranty

More information

SebArt professional line

SebArt professional line SebArt professional line Wind S 50E ARF ASSEMBLY MANUAL The new Wind S 50E ARF was designed by Italy aerobatic pilot Sebastiano Silvestri, it is the replica of his 2 meter size F3A competition airplane,

More information

Instruction Manual EXTRA 260-EP. 1075mm (42.32 in) 1000mm (39.37 in) 1100gr gr. 4 channel - 4 mini servo. Axi motor 2820

Instruction Manual EXTRA 260-EP. 1075mm (42.32 in) 1000mm (39.37 in) 1100gr gr. 4 channel - 4 mini servo. Axi motor 2820 1075mm (42.32 in) 1000mm (39.37 in) 1100gr - 1400gr 4 channel - 4 mini servo Axi motor 2820 KIT CONTENTS: We have organized the parts as they come out of the box for better identification during assembly.

More information

Instruction Manual. Wingspan : 1694mm (66.69 in) : 1470mm (57.87 in) : 3200gr gr. : 61 two stroke/ 71 four stroke. : 6 channel / 7 servo

Instruction Manual. Wingspan : 1694mm (66.69 in) : 1470mm (57.87 in) : 3200gr gr. : 61 two stroke/ 71 four stroke. : 6 channel / 7 servo Wingspan : 1694mm (66.69 in) g Length : 1470mm (57.87 in) Weight : 3200gr - 3800gr Engine : 61 two stroke/ 71 four stroke Radio : 6 channel / 7 servo KIT CONTENTS: We have organized the parts as they

More information

THUNDERBOLT P47G SNAFU 60 ARF ASSEMBLY MANUAL. ALMOST READY TO FLY

THUNDERBOLT P47G SNAFU 60 ARF ASSEMBLY MANUAL.   ALMOST READY TO FLY WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL THUNDERBOLT P47G SNAFU 60 ARF Graphics and specifications may change without notice. MS: 207 ALMOST READY TO FLY Specifications: Wingspan---------------63.0 in (160

More information

MX2 100CC & MXS-R 100CC Giant Scale Aerobatic Aircraft

MX2 100CC & MXS-R 100CC Giant Scale Aerobatic Aircraft MX2 100CC & MXS-R 100CC Giant Scale Aerobatic Aircraft By the act of using the final assembled model, the purchaser/operator accepts all resulting liability. Included Features: Fuselage and Wing incorporate

More information

MAXI LIFT. 33cc ASSEMBLY MANUAL. ALMOST READY TO FLY. Specifications: MS: 209

MAXI LIFT. 33cc ASSEMBLY MANUAL.   ALMOST READY TO FLY. Specifications:   MS: 209 WWWSEAGULLMODELSCOM ASSEMBLY MANUAL MAXI LIFT 33cc Graphics and specifications may change without notice MS: 209 ALMOST READY TO FLY Specifications: Wingspan---------------876 in (2222 cm) Wing area----------------10726sqin

More information

Instruction Manual. We wish you many enjoyable flights with your plane and once again thank you for your choosing a Phoenix Model product

Instruction Manual. We wish you many enjoyable flights with your plane and once again thank you for your choosing a Phoenix Model product Instruction Manual Wing span: 1590mm (626 in) Length: 1100mm (433 in) Weight: 1500gr - 1700gr Motor: AXI 2814/10 or Motor: 500-600 w/ gear box Radio: 4 Channel / 4 servos standar Propeller: 12 x 47 We

More information