Standard filter Disk filter Return filter. Lubrication systems can fail from the following

Size: px
Start display at page:

Download "Standard filter Disk filter Return filter. Lubrication systems can fail from the following"

Transcription

1 Filters For oil For use in SKF centralized lubrication systems Standard filter Disk filter Return filter Why filtering? Solids are diagnosed to be the main cause of damages on the components that are used in lubrication systems. Malfunctions or a shutdown of the machine or system occur if components are damaged by dirt. Lubrication systems can fail from the following causes: Contamination prior to the start-up (e.g. metal chips, paint residues) Contamination during the installation (e.g. burr formation, sealing material) Contamination in the oil (e.g. residues during production and filling) Contamination after the start-up (e.g. wear, oil ageing, water in the oil) Filters help prevent system or component failures from such causes. Filters reduce solids and the system can be operated more economically, reliably and maintenance-friendly.

2 ! Important information on product usage ll SKF products may be used only for their intended purpose as described in this brochure and in the operating instructions. If operating instructions are supplied together with the products, they must be read and followed. Not all lubricants can be fed using centralized lubrication systems. SKF can, on request, inspect the suitability of the lubricant selected by the user for pumping in centralized lubrication systems. Lubrication systems and their components manufactured by SKF are not approved for use in conjunction with gases, liquefied gases, pressurized gases in solution, vapors or such fluids whose vapor pressure exceeds normal atmospheric pressure (1013 mbar) by more than 0.5 bar at their maximum permissible temperature. In particular, we call your attention to the fact that hazardous materials of any kind, especially the materials classified as hazardous by EC Directive 67/548/EEC, rticle, ara., may only be filled into SKF centralized lubrication systems and components and delivered and/or distributed with the same after consultation with and written approval from SKF.

3 Table of contents Standard filters DIN General... 4 Characteristics... 5 Filter mount... 5 ressure filter as per DIN 4550, complete... 6 Dirt indicators... 7 Examples for standard filters, complete... 8 Filter elements/filter housings Double changeover filters as per DIN 4550, complete Screen filters... 1/13 Suction strainers Disk filters... 14/15 Return filters... 16/17 Venting filters

4 Filter Standard filters DIN 4550 General Filter design The pressure filters are standard filters according to DIN They are modular in design. They consist of a filter housing (filter head/ filter body) (fig. 1), a filter element (fig. ) and a screw plug (fig. 4). Optionally a dirt indicator (fig. 3) can be selected instead of the screw plug. In the standard design, the filters are delivered with a screw plug. Fig. 1 Fig. Filter housing The housings are used to accommodate the filter element and are available in various designs and nominal dimensions (NG 40; NG 63; NG 100) without reverse flow valves with reverse flow valves Filters with two reverse flow valves can be flushed in both directions. Filtering takes place only in one direction. Function: Fluid flows from to, necessarily via the filter element. The flow from to does not take place via the filter element, because the first check valve will close.the second valve opens in direction. Filter element see table (page 6) The filter element removes the solids from the lubricant. Filter element in star crimp (high dirt retention) Flow direction from the outside to the inside Dirt indicators see table 3 (page 7) The dirt indicator monitors the filter element and signals when it needs to be the replaced. electrical/optical/m1 1/ NO-contact-NC contact (75%/100%) electrical/m1 1/NO-contact-NC contact (75%/100%)/LED/cold start suppression electrical/optical/m1 1/NC contact (75%/100%) electrical/m1 1/NO-contact-NC contact (75%/100%)/LED optical electrical DIN EN (DIN 43650)/changeover contact The response pressure of the dirt indicators is p = 5 bars. Filter maintenance The dirt indicator displays when the next filter maintenance is due. roper maintenance helps to maximize utilization of filter elements. Fig. 3 Fig Fiberglass fleece disposable elements based on inorganic fibers/ absolute filtration pplication: max. allow. p on element 30 bars rotection against element damage Collapse pressure resistance 0 bars Hydraulic plan 1 Filter installation The pressure filters are used as line filters in the pipes of the lubrication system for separating solids from the fluids. This increases the service life of the system s components and minimizes the chance of system failure. When arranging the filter on the container or in the system, make sure that the filters are easily accessible and that the filter cartridges can be easily replaced. Strictly adhere to the installation height (technical drawing starting from page 10). Otherwise the change of the filter cartridge cannot be ensured. The mounting position is vertical.. Wire fabric/nominal filtration High permissible temperature range Cleanable Collapse pressure resistance 30 bars! ccessories Connecting pieces, see brochure EN. Repair kit consisting of various FKM (FM) seals.. 4

5 Filter Standard filters DIN 4550 Technical data Characteristics Temperature range C to +100 C Compatibility with fluids.... Mineral oils, difficultly Mounting position... Vertical, make certain the direction of flow is correct. inflammable and watercontaining fluids, rapidly biodegradable fluids Connections acc. to ISO 8... G 1 / Material Housing, cpl.... luminum Volumetric flow up to liters Gasket.... FKM (FM) ressure stage liters 100 liters 100 bars Filtermaterial... Fiberglass fleece inorganic fiber absolute filtration Wire fabric stainless steel nominal filtration Filter mount Table 1 Designation Order No. Mounting bracket Fig. 5 Mounting bracket for 3-liter plastic and metal reservoir Retaining plate for 6-liter plastic reservoir Filter plate for 6-liter metal reservoir Filter plate for 15-liter metal reservoir Filter plate for 30-liter metal reservoir Filter plate for 50-liter metal reservoir ø7 ø Fig. 6 Fig. 7 Retaining plate Filter plate ø6.5 (x) 9 ø6 t = 4 ø6 10x ø t =,

6 ressure filter DIN 4550 Selection table Table Dirt retention Reverse Filter Filter or filter area flow fig. rating ISO 16889/ Filter valve 3) Dirt dispaly 1) ) Standard filter, kpl. Element 1) Dim. Housing Order No. no. NG Order No. [µm] at p = 5 bars element ( ) Order No. draw. Order No V g Fiberglass fleece with V g Fiberglass fleece with g Fiberglass fleece with V V g Fiberglass fleece with V V g Fiberglass fleece with V g Fiberglass fleece without V g Fiberglass fleece without V g Fiberglass fleece without V g Fiberglass fleece with V g Fiberglass fleece without V g Fiberglass fleece without V g Fiberglass fleece with g Fiberglass fleece with V g Fiberglass fleece with V g Fiberglass fleece with V g Fiberglass fleece with g Fiberglass fleece with g Fiberglass fleece with g Fiberglass fleece with g Fiberglass fleece with g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece with V g Fiberglass fleece with g Fiberglass fleece without Fiberglass fleece without V m² Wire fabric with V V m² Wire fabric with V m² Wire fabric with V m² Wire fabric with g Fiberglass fleece with g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece without V m² Wire fabric with g Fiberglass fleece without g Fiberglass fleece without g Fiberglass fleece without V m² Wire fabric with V m² Wire fabric without g Fiberglass fleece without m² Wire fabric with m² Wire fabric with m² Wire fabric with m² Wire fabric without m² Wire fabric without m² Wire fabric without Fittings according ISO 8: G 1 / ressure filter without by-pass 6

7 Dirt indicators Table 3 Order No. Dim. draw. Indication 1) Switching type Electrical connection ) Switching points Electrical/Optical 1 NO-contact / 1 NC-contact M1 1 / 4-pin 75% / 100% Electrical/Optical 1 NO-contact / 1 NC-contact M1 1 / 4-pin / LED- 75% / 100% Cold start suppression 30 C Electrical/Optical NC-contact M1 1 / 4-pin 75% / 100% Electrical/Optical 1 NO-contact / 1 NC-contact M1 1 / 4-pin / LED 75% / 100% Optical Electrical Changeover contact DIN EN Screw plug Opening pressure: p = 5 bars Fig. 8 Fig. 9 Fig. 10 Screw plug Electrical/Optical Electrical with LED M M LED Fig. 11 Fig. 1 Hydraulic plan Electrical Optical 1) Other filter housings (e.g. with by-pass), filter elements (e.g. stainless steel) and dirt indicator (e.g. opening pressure at bars) on request. ) The cold start suppression prevents an activation of the dirt indicator when temperatures fall below 30 C. 3) Filters with two reverse flow valves can be flushed in both directions. Filtering takes place only in one direction. Function: Fluid flows from to, necessarily via the filter element. The flow from to does not take place via the filter element, because the first check valve will close. The second valve opens in direction. 7

8 Standard filters Examples, complete Fig. 13 Fig. 14 Fig. 15 With screw plug With electrical/optical dirt indicator With electrical/optical dirt indicator LED 46 Order No Screw plug Hydraulic plan 3 with reverse flow valve Hydraulic plan 4 without reverse flow valve Order No V V V V V Hydraulic plan 5 with reverse flow valve Hydraulic plan 6 without reverse flow valve Order No Hydraulic plan 7 with reverse flow valve Hydraulic plan 8 without reverse flow valve Wiring diagram 1 Dirt indicator NO-contact NC-contact M1 1 N +4 V DC WH 100% alarm (off) K 75% pre-warning(on) U in 3: not occupied ζ T>30 C 75% 100% 1.GN RD YE.GN Wiring diagram Dirt indicator NO-contact NC-contact M1 1 Cold start suppression N U +4 V 0 V WH - 100% alarm (off) K V 75% pre-warning (0n) Wiring diagram 3 Dirt indicator NC-contact M1 1 Wiring diagram 4 Dirt indicator NO-contact NC-contact M1 1 75% 100% N U not used +4 V WH 100% alarm (off) K 75% pre-warning (off) 75% 100% GN RD YE N +4 V U 0 V WH 100% alarm (off) K 75% pre-warning (on) 8

9 Standard filters Examples, complete Fig. 16 Fig. 17 With electrical dirt indicator With optical dirt indicator Order No. Hydraulic plan 9 Order No. Hydraulic plan with reverse flow valve Hydraulikplan with reverse flow valve Hydraulikplan 1 without reverse flow valve without reverse flow valve Wiring diagram 5 Dirt indicator DIN EN max. 30 V C 3 E 9

10 Filter elements and filter housing Filter elements 1) Filter elements are available in different nominal dimensions (NG) and filter ratings Filter housing 1) Filter housings are available in different nominal dimensions (NG) and with/without reverse flow valves: Filter elements 3 µm: V57...NG NG µm: NG NG NG µm: NG 63 with reverse flow valve: NG NG 63 without reverse flow valve: NG NG NG 100 Filter housing Fig µm: V57...NG NG NG NG µm: NG 40 Filter housing 84 NG 40 G1/ NG NG (NG 100) ø48 75 (necessary distance for filter maintenance) 146 (NG 40) 05 (NG 63) Filter elements Fig M6 9 1) Other filter housings (e.g. with by-pass), filter elements (e.g. stainless steel) and dirt indicator (e.g. opening pressure at bars) on request. 10

11 Double changeover filter as per DIN4550 Table 4 Double changeover filter Element 1) Filter rating Dirt retention or filter area ISO 16889/ Filter element Dirt dispaly 1) Connections as per Order No. NG Order No [µm] bei p = 5 bars material Order No. Fig. ISO g Fiberglass fleece G 1 / g Fiberglass fleece G 1 / Repair seal kit: sealing material: FKM (FM) Observe 75 mm space requirement below for the replacement of the filter element! Double changeover filter max Fig. 0! ccessories Connecting pieces, see brochure EN. Wiring diagram min. 196 / max. 05 G1/ M ø33 3 WF13 3 ø Verschmutzungsanzeige x Öffner 75% 100% N U WH K +4 V not used 100% alarm 75% pre-warning 75 5 Hydraulic plan 13 ø M6 G1/ Vent G1/8 9 1) Other filter housings (e.g. with by-pass), filter elements (e.g. stainless steel) and dirt indicator (e.g. opening pressure at bars) on request. 11

12 Screen filters These filters should be used preferably in the delivery (discharge) lines for intermittently operated, centralized lubrication systems. To clean the screen filter element, the hexagon screw (SW 13) must be unscrewed. The filter element can then be pulled out without loosening the tubing. pproximately 40 mm space below is required for the cleaning of the filter element. Table 5 Filter Reverse Flow Operating Screen filter Dim. Element Filter element flow Hyraulic Meshwidth Screen rate pressure Dirt indicator Connections Order No. draw. Order No. rating material valve plan area volume max. Order No. [µm] [bar] [mm] [cm ] [l/min] [bar] U1 63 Wire fabric without 14 0,063 1 ) 60 without G 1 / F * ) U 160 Wire fabric without 14 0, without G 1 / U1 5 Wire fabric without 14 0, without G 1 / U1 30 Wire fabric without 14 0, without G 1 / U1 5 Wire fabric ,05 1 1) 45 without M ** ) U1 5 Wire fabric without 14 0, without G 1 / U1 3 Filter fabric without 14 0, ) 60 without G 1 / F U 160 Wire fabric , ) 45 without G 1 / U1 3 Wire fabric without 14 0, ) G 1 / F U 160 Wire fabric without 14 0, without G 1 / G 1 / *) for grease, NLGI grades 000 and 00 **) for grease, NLGI grade 000 1) t an operating viscosity of the flow medium of 100 mm /s, a pressure loss of 0.38 bar and a clean filter. ) t an operating viscosity of the flow medium of 370 mm /s, a pressure loss of 0.5 bar and a clean filter.! ccessories Connecting pieces, see brochure EN Fig. 1 ø19 G1/4 G1/ ø WF 13 MDmax = 0 Nm 1

13 Screen filters Fig. Fig M ø5.5 8 M G1/4 ø5.5 G1/ WF 13 MDmax = 0 Nm ~15 Space required for cleaning of the filter element 13 WF 13 MDmax = 0 Nm Wiring diagram M p p1 35 Dirt indicator M Hydraulic plan 14 Hydraulic plan pre-warning 75% alarm 100% +4 V DC Suction strainers Table 6 Strainer Tube Material Order No. outer ø d1 d h WF acc. to DIN 4189 [mm] [mm] [mm] [mm] Strainer d1 Fig M Wire fabric M Wire fabric M Wire fabric WF h ipe thread d1 for port tapped for solderless tube connection DIN 385! ccessories Connecting pieces, see brochure EN. d 13

14 Disk filters General In the main and by-pass flow, disk filters can be used. Wire disk filters are suitable for the filtration of very soiled media. The filter elements are flushed from the outside to the inside. The filter rating is determined by the gap width. Disk filters are easy to maintain and are characterized by their long service life. Cleaning can be performed during operation by turning the handle. The dirt particles collect in the collecting area and are emptied by loosening the screw plug during operation or downtimes. CUTION Strictly adhere to the installation height shown in the technical drawings to enable the change of the filter element. Table 7 Disk filters Dim. Nominal Operating Operating Max. differential Order No draw. Gap width flow pressure overpressure pressure strenth coil Connections [l/min] [bar] [bar] [bar] µm 35 1) 40 G µm 60 40/63 40 G µm G 3 / µm G 1 1) The flow specifications apply to fluids with a viscosity of 7 mm /s at a flow resistance of 0. to 0.4 bar. In case the amount of dirt is low and the flow resistance may increase, the indicated flow specifications can be exceeded.! ccessories Connecting pieces, see brochure EN. 14

15 Disk filters Fig. 5 Fig space requirement usbauhöhe for cleaning ca G1 ø84 ±3 G1 G ±3 390 ±8 ø75 M1; 6 deep tief ± G 3 /4 M8 14 deep ø ± ±4 space requirement for cleaning Fig. 7 space requirement for cleaning ø11 (x) 41 C ø

16 Return filters Filter installation The return filter is installed on a container or tank and prevents dirt particles in fluid from entering the system. Thereby are especially the pump units protected. Filter design The return filter consists of: Housing Element Container ventilation Optionally, an electric dirt indicator, a pressure switch and/or a by-pass valve can be included with the filter (see table 8). Filter element The filter element removes the solids from the lubricant. Filter element in star crimp Large filter areas Low pressure losses Especially long maintenance intervals Flow direction from the outside to the inside Filter maintenance The dirt indicator displays when the next filter maintenance is due. roper maintenance helps to maximize utilization of filter elements. Table 8 Return filters Dim. Filter Filter Filter Nominal Operating Valve ressure Order No draw. rating area element flow pressure max. setting Connection switch [µm] [cm ] [bar ] [l/min] [bar ] [bar ] [bar ] (set) G 1 / G 1 / G 1 / G G 1 / G 1 / 1. ±0. 1) max. switching capacity = 100 V C/DC; max. switching capacity = 4 V C/DC; switching type = NO-contact Technical datat Characteristics Fluid temperature range C to +100 C Mounting position preferably vertically, discharge is pointing down Min. diff. pressure to 1 bar Connections G 1/; G1 Nominal flow from 18 to 95 liters Volumetric flows up to liters 63 liters Compatibility with fluids Mineral oils, environmentally-friendly hydraulic fluids Materials Cover olyamide, GF-reinforced Housing luminum Gasket FKM (NR) Filter Microfiber fleece, aper, Filter fabric! ccessories Connecting pieces, see brochure EN. CUTION Strictly adhere to the installation height shown in the technical drawings to enable the change of the filter element. 16

17 Return filters Fig. 8 Fig. 9 Fig ±0. 6 ±0.5 ø73.5 ø5 min space min. requirement 140 for maintenance 4 ± space requirement for maintenance ± ± G1 ±0.6 ø104.5 ø91 max. ø87 min. ø ø75 ø60 min. ø63 max. ø33.5 G 1 / G 1 / ø ø7.8 ø51 ø11 (x) 37 SW7 G1/ 9 ø ø to fit in into the container space requirement for maintenance to fit in into the container ±0.3 ±0.3 for container ventilation R13.5 1± space requirement for maintenance 17

18 Venting filters Table 9 Venting filters Dim. Filter Filter Temperature Order No. draw. rating element range [µm] [ C] aper fleece 30 to apiervlies 30 to apiervlies 30 to to olyurethane foam 15 to +100 Fig. 31 Fig. 33 Fig. 35 ø77 ø49 ø G 1 / G 1 /4 ø3 O-ring 37.5 Fig. 3 ø83 ø76 ø G 3 /4 Fig SW Drill-hole pattern 60 ø8 G 1 /4 ø49 ø60 ø73 M5(6x) 18

19 Notes 19

20 Important information on product usage! SKF and Lincoln lubrication systems or their components are not approved for use with gases, liquefied gases, pressurized gases in solution and fluids with a vapor pressure exceeding normal atmospheric pressure (1 013 mbar) by more than 0,5 bar at their maximum permissible temperature. dditional brochures for further information: DE Fittings and ccessories DE Transport of Lubricants in Centralized Lubrication Systems SKF Lubrication Systems Germany GmbH erlin lant Motzener Str. 35/ erlin O ox erlin Germany This brochure was presented to you by: Tel. +49 (0) Fax +49 (0) SKF is a registered trademark of the SKF Group. SKF Group 018 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication, but no liability can be accepted for any loss or damage whether direct, indirect or consequential, arising out of use of the information contained herein. October 018 skf.com/lubrication

Standard filter Disk filter Return filter. Lubrication systems can fail from the following

Standard filter Disk filter Return filter. Lubrication systems can fail from the following Filters For oil For use in SKF centralized lubrication systems Standard filter Disk filter Return filter Why filtering? Solids are diagnosed to be the main cause of damages on the components that are used

More information

For high-viscosity oils and fluid grease of NLGI grades 000, 00 For use in SKF MonoFlex single-line centralized lubrication systems

For high-viscosity oils and fluid grease of NLGI grades 000, 00 For use in SKF MonoFlex single-line centralized lubrication systems Gear pump unit roduct series KFB For high-viscosity oils and fluid grease of NLGI grades 000, 00 For use in SKF MonoFlex single-line centralized lubrication systems SKF gear pump units of the KFB product

More information

Directional Valves for oil or grease

Directional Valves for oil or grease 1-173-EN Directional Valves for oil or grease 161-1-31 161-1-5 DV5-4 Function he directional valves listed on the following pages are used to control the flow of lubricants, e.g. to divide up a central

More information

Manually or pneumatically actuated Piston pumps

Manually or pneumatically actuated Piston pumps Manually or pneumatically actuated Piston pumps For oil and fluid grease For use in SKF MonoFlex single-line centralized lubrication systems These manually or pneumatically actuated piston pumps were designed

More information

Compact Units. For fluid grease, NLGI grades 000, 00 Group MKF 0.1 or 0.2 l/min EN

Compact Units. For fluid grease, NLGI grades 000, 00 Group MKF 0.1 or 0.2 l/min EN 1-16-EN Compact Units For fluid grease, NLGI grades, Group MKF.1 or.2 l/min MKF1-KW2-2 MKF2-KW3-2 MKF2-KW6-22 These MKFcompact units were developed to supply intermittently operated single-line centralized

More information

UD and UC Gear pump unit

UD and UC Gear pump unit 1-19-EN for SKF CircOil or hydraulic lubrication systems General Information The UC and UD gear pump units are vertically or horizontally arranged units that are used in hydraulic or circulating-oil lubrication

More information

Manually or pneumatically actuated piston pumps

Manually or pneumatically actuated piston pumps Manually or pneumatically actuated piston pumps Product series Pxx For oil and fluid grease For use in SKF MonoFlex single-line centralized lubrication systems Manually or pneumatically actuated piston

More information

Injection oilers, micro pumps for minimal quantity metering

Injection oilers, micro pumps for minimal quantity metering 1-5012-4-EN Injection oilers, micro pumps for minimal quantity metering Injection oiler, 3-port type Injection oiler, 1-port type Micro pump Delivery rates Metering pumps deliver lubricants in a measured

More information

Inexpensive solution for the lubrication of linear guides and rolling bearings

Inexpensive solution for the lubrication of linear guides and rolling bearings 1-0988-EN Compact Greaser Inexpensive solution for the lubrication of linear guides and rolling bearings Compact Greaser Up to 5 lubricant outlet ports 3 different metered volumes (15 mm 3 standard) Suitable

More information

Accessories for Minimal Quantity Metering

Accessories for Minimal Quantity Metering 1-5012-5-EN Accessories for Minimal Quantity Metering for chain lubrication and surface wetting Brush Spray head Flow volume divider Nozzles Pinpoint application of metered quantities of oil Brushes Storage

More information

PPU, PHU Piston Pumps for progressive grease and oil systems, pneumatically or hydraulically actuated

PPU, PHU Piston Pumps for progressive grease and oil systems, pneumatically or hydraulically actuated 1-0107-5-EN PPU, PHU Piston Pumps for progressive grease and oil systems, pneumatically or hydraulically actuated These piston pumps are available with two different delivery rate ranges. The pumps can

More information

SP/SMT 1 Flow Divider

SP/SMT 1 Flow Divider 1-5017-EN S/SMT 1 Flow Divider with and without inline strainer for circulating-oil or hydraulic systems Introduction The flow divider splits the supplied flow into two equal induvidual flows or into two

More information

For grease For application in SKF DuoFlex dual-line centralized lubrication systems

For grease For application in SKF DuoFlex dual-line centralized lubrication systems Change-over valves, differential pressure switch ccessories for Dual-line Systems For grease For application in SKF DuoFlex dual-line centralized lubrication systems Change-over valves Hydraulical or electrical

More information

" " (495) For oil For continuous monitored lubrication with minimum quantities from 0,5 to 5 mm³/min

  (495) For oil For continuous monitored lubrication with minimum quantities from 0,5 to 5 mm³/min System integration only in close cooperation with SKF Portfolio management Microdosage system MDS Product series MDx For oil For continuous monitored lubrication with minimum quantities from 0,5 to 5 mm³/min

More information

Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated

Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated 1-0107-4-EN Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated PF-23-2 PFP-23-2 PFH-23-2 Single- and dual-circuit piston pumps are designed for the

More information

Single-Line Centralized Lubrication Systems

Single-Line Centralized Lubrication Systems 1-15-EN Single-Line Centralized Lubrication Systems For fluid grease, NLGI grades, PFE-15-1. PF-289 MFE2-KW6F-S1 U1 U2 U3 The layout of a single-line centralized lubrication system for grease is largely

More information

Electric Plug-and-Socket Connectors

Electric Plug-and-Socket Connectors -70-EN Electric Plug-and-Socket Connectors Sockets for pressure switches, level switches, flow sensors, directional control valves and filters DIN EN 750-80/ISO 4400 DIN EN 750-804 M Electric plugs or

More information

Block feeder SPVS Used in oil or grease lubrication systems

Block feeder SPVS Used in oil or grease lubrication systems 1-3029-EN Block feeder SPVS Used in oil or grease lubrication systems Block feeders of the SPVS series are used in grease and oil total loss lubrication systems. They are used to either increase the number

More information

SKF VectoLub, VE1B units

SKF VectoLub, VE1B units 1-4403-EN SKF VectoLub, VE1B units External minimal quantity lubrication, Volumetric metering The emql system SKF VectoLub is a clean and economical alternative for lubricant projection in minimal quantity.

More information

Block feeder SPVS Used in oil or grease lubrication systems

Block feeder SPVS Used in oil or grease lubrication systems 1-3029-EN Block feeder SPVS Used in oil or grease lubrication systems Block feeders of the SPVS series are used in grease and oil total loss lubrication systems. They are used to either increase the number

More information

Flow limiter SP/SMB13 for line installation in circulating-oil lubrication systems.

Flow limiter SP/SMB13 for line installation in circulating-oil lubrication systems. 1-3004-EN Flow limiter SP/SMB13 for line installation in circulating-oil lubrication systems. Flow limiters are used in circulating-oil lubrication systems. The task of a flow limiter is to divide up the

More information

SKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B EN

SKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B EN SKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B 1-4402-EN Spray blocks Every spraying unit is connected to the coaxial outlet of a VTEC or VE1B unit. It

More information

Grease Pump Units. For progressive and multiline systems, manually, pneumatically or hydraulically actuated. Please note!

Grease Pump Units. For progressive and multiline systems, manually, pneumatically or hydraulically actuated. Please note! 1-0107-4-EN Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated PF-23-2 PFP-23-2 PFH-23-2 Single- and dual-circuit piston pumps are designed for the

More information

Motor-driven pump unit GSJB

Motor-driven pump unit GSJB 1-4002-1-EN Motor-driven pump unit GSJB Multi-outlet pump units with oil or grease reservoir designed for centralized lubrication systems The motor-driven pump units GSJB have been especially designed

More information

Flow Monitors and Sensors

Flow Monitors and Sensors 1-1704-EN Flow Monitors and Sensors for intermittent and circulating centralized lubrication systems Flow monitor Flow sensor Oil-streak sensor Flow monitors/sensors have the task of monitoring the flow

More information

PTEX extruder pumps Pneumatic extruder pump for drums of grease up to NLGI grade 2

PTEX extruder pumps Pneumatic extruder pump for drums of grease up to NLGI grade 2 1-4009-EN PTEX extruder pumps Pneumatic extruder pump for drums of grease up to NLGI grade 2 The PTEX extruder pumps are pneumatically actuated pumps designed to deliver lubricant under pressure to lubrication

More information

Injection oilers, micro pumps

Injection oilers, micro pumps 1-5012-4-EN Injection oilers, micro pumps for minimal quantity metering Injection oiler, 3-port type Injection oiler, 1-port type Micro pump Delivery rates Metering pumps deliver lubricants in a measured

More information

Flow limiter SP/SMB10 Dual flow series

Flow limiter SP/SMB10 Dual flow series 1-00-EN Dual flow series Advantages reliable - Parallel distribution of individual flow quantities - self-regulating metering with pressure balancing valve, thus constant volumetric flows even for different

More information

Product series DSA, DSB, DSC, DSD

Product series DSA, DSB, DSC, DSD Pressure Switches Product series DSA, DSB, DSC, DSD For oil, fluid grease and grease For use in SKF centralized lubrication systems, hydraulic and compressed-air systems DSA DSB DSC SKF pressure switches

More information

Grease Lubrication Pump FK

Grease Lubrication Pump FK 1-3033-EN 1-0358-US for use in progressive, single-line and dual-line centralized lubrication systems pplication he FK pump unit is a multi-function piston pump whose modular structure makes it very versatile.

More information

System description for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines

System description for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines Valve seat lubrication Cylinder lubrication Version 04 Page 2 for cylinder lubrication and valve seat lubrication on

More information

Block metering device VPB. Block feeder for use in oil or grease lubrication systems

Block metering device VPB. Block feeder for use in oil or grease lubrication systems Block metering device VPB Block feeder for use in oil or grease lubrication systems Block metering device VPB Block metering devices or feeders of the VPBM/VPBG series are used in small circulating-oil

More information

Chain lubrication, accessories Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication EN

Chain lubrication, accessories Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication EN Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication 1-106-EN 16 10,5 16 10,5 ~ ~ Chain lubrication, accessories Oil projection nozzle AC-A Compact design, pinpoint accuracy,

More information

Flow limiter SP/SMB3 Flow limiter SP/SMB6

Flow limiter SP/SMB3 Flow limiter SP/SMB6 -00-EN Flow limiter SP/SMB Flow limiter SP/SMB6 for circulating-oil lubrication systems Advantages reliable perpetual dispensation of individual volume flows - self-adjusting metering, thus identical volume

More information

Flow limiter SP/SMB9 for mounting plates

Flow limiter SP/SMB9 for mounting plates 1-3002-EN Flow limiter SP/SMB for mounting plates Advantages reliable perpetual dispensation of individual volume flows - self-adjusting metering, thus identical volume flows despite different back pressures.

More information

Chain lubrication, accessories

Chain lubrication, accessories 1-106-EN Chain lubrication, accessories Nozzles, oiling brushes, reservoirs and other accessories for chain lubrication Oil projection nozzle AC-A Compact design, pinpoint accuracy, and high temperature

More information

PS/PSL Centrifugal pumps

PS/PSL Centrifugal pumps 1 14 EN Centrifugal pumps Technical Data Delivery rate Q max = 1250 l/min Delivery head H max = 110 m Delivery temperature T = 0 C to + C Kinematic viscosity ν max = 30 mm 2 /s Quality Management DIN EN

More information

For reliable control of small, large or multi-system-type lubrication systems

For reliable control of small, large or multi-system-type lubrication systems LMC 301 controller For reliable control of small, large or multi-system-type lubrication systems Models 86500, 86501 Models 86502, 86503 Designed for use with pumps that have no internal controller, the

More information

Product series DigitalSuper

Product series DigitalSuper Minimal quantity lubrication (MQL) SKF LubriLean Product series DigitalSuper Extended product range with enhanced performance and state-of-the-art communication Products and applications The innovative

More information

SKF Grease injection system

SKF Grease injection system 1-4101-EN SKF Grease injection system Grease injecting lubrication system type GVP for moving conveyor chain pins and rollers The grease injecting lubrication system GVP has been developed to carry out

More information

SKF Multilube pumping unit

SKF Multilube pumping unit SKF Multilube pumping unit for heavy vehicle lubrication systems SKF Multilube pumping unit SKF centralised lubrication systems are an effective solution for lubrication maintenance of heavy vehicles.

More information

PRA Centrifugal pumps

PRA Centrifugal pumps 1 6001-EN PRA Centrifugal pumps Technical data Delivery rate Q max = 130 l/min Delivery head H max = 30 m Temperature range T = 5 C to 60 C Kinematic viscosity ν max = mm 2 /s Quality Management DIN EN

More information

ES 094 Tank top mounting Connection up to G1¼ Nominal flow rate up to 70 l/min

ES 094 Tank top mounting Connection up to G1¼ Nominal flow rate up to 70 l/min Suction Filters ES 094 Tank top mounting Connection up to G1¼ Nominal flow rate up to 70 l/min Description pplication To be installed in the suction line of the pumps of hydraulic systems resp. upstream

More information

Injection Oilers, Micro Pumps

Injection Oilers, Micro Pumps Injection Oilers, Micro Pumps 1-5012-4-US for minimal quantity metering Magnetic piston pump Injection oiler Micropump Grease metering P Metering pumps deliver and meter out lubricants. This piston pumps

More information

PSR Centrifugal pumps

PSR Centrifugal pumps 1 65 EN Centrifugal pumps Technical data Delivery rate Q max = 180 l/min Delivery head H max = 255 m Temperature range T = -10 C to +80 C Kinematic viscosity ν max = mm 2 /s Quality Management DIN EN ISO

More information

Metering Units and Piston Distributors with Quick Connector System

Metering Units and Piston Distributors with Quick Connector System 1-5015-US Metering Units and Piston Distributors with Quick Connector System for single-line total-loss lubrication systems (oil or fluid grease) Group 320: 0.01-0.16 ccm for oil 0.03-0.10 ccm for fluid

More information

Lubrication System CLU4

Lubrication System CLU4 1-0304-EN Lubrication System CLU4 for lubrication of large 2-stroke crosshead diesel engines - resulting in your operating costs being cut due to lower oil consump tion The advantages you get from a system

More information

Air-oil centralized lubrication systems

Air-oil centralized lubrication systems Air-oil centralized lubrication systems A lubrication system should always be as modern and efficient as the machine it is lubricating. Lincoln air-oil systems are ideally suited for this because they

More information

Suction Filter Pi 200

Suction Filter Pi 200 Suction Filter Pi 0 Nominal size up to 90 1. Features High performance filters for modern hydraulic systems Provided for pipe installation Modular system Compact design Minimal pressure drop through optimal

More information

Spin-on elements. Type 80, 81 and 82. Contents. Features. RE Edition:

Spin-on elements. Type 80, 81 and 82. Contents. Features. RE Edition: Spin-on elements Type 80, 81 and 82 RE 51478 Edition: 2015-06 Sizes according to according to Bosch Rexroth standard: 30 to 130 Pressure differential resistance up to 5 bar [72.5 psi] Filter rating: 1

More information

PSG product series. Modular feeder. For oil and grease For use in SKF ProFlex progressive and SKF CircOil circulating centralized lubrication systems

PSG product series. Modular feeder. For oil and grease For use in SKF ProFlex progressive and SKF CircOil circulating centralized lubrication systems odular feeder PSG product series For oil and grease For use in SKF ProFlex progressive and SKF CircOil circulating centralized lubrication systems PSG1 PSG2 PSG3 Fields of application etal-forming machinery

More information

JM Oil Lubrication Pump SKF MultiFlex multi-line pump units for total loss oil lubrication systems on compressors

JM Oil Lubrication Pump SKF MultiFlex multi-line pump units for total loss oil lubrication systems on compressors 1-3007-EN SKF MultiFlex multi-line pump units for total loss oil lubrication systems on compressors General Information The JM oil lubrication pump is a highpressure multiline pump that produces a maximum

More information

Lubrication System CLU4

Lubrication System CLU4 1-0304-EN Lubrication System CLU4 for lubrication of large 2-stroke crosshead diesel engines - resulting in your operating costs being cut due to lower oil consump tion The advantages you get from a system

More information

Connection Ports: 3/4 1 1/4 BSP (other thread options on request)

Connection Ports: 3/4 1 1/4 BSP (other thread options on request) HYDRAULIC FILTRATION Medium pressure, in line spin-on filters Technical Information Pressure: Max working (acc. to NFPA T 3.10.17): FA-4-1x: 34,5 bar (500 psi) FA-4-21: 24 bar (348 psi) Burst (acc. to

More information

Oil Filter Module Pi 8300

Oil Filter Module Pi 8300 Oil Filter Module Pi 8300 Volume flow 1 und 220 l/min 1. Features Compact, ready-to connect oil filter module for modern hydraulic and lubrication systems Low noise internal gear pump Minimum loss of performance

More information

High Pressure Filter Pi 4000

High Pressure Filter Pi 4000 High Pressure Filter Pi 4000 Nominal pressure 400 bar (5690 psi), nominal size up to 400 according DIN 24550 1. Features High performance filters for modern hydraulic systems Modular system Compact design

More information

for SKF DuoFlex dual-line lubrication systems

for SKF DuoFlex dual-line lubrication systems SGA and SG-dosers for SKF DuoFlex dual-line lubrication systems Modular and mechanically adjustable SGA and SG-dosers are used in SKF DuoFlex applications. SGA and SG-dosers The dosing modules are hydraulically

More information

Medium Pressure Filter Pi 340

Medium Pressure Filter Pi 340 Medium Pressure Filter Pi 340 Nominal pressure 250/315/350 bar (3560/4480/4980 psi), nominal size up to 450 (also available with filter elements acc. to DIN 24550) 1. Features. High performance filters

More information

Medium Pressure Filter Pi 3000

Medium Pressure Filter Pi 3000 Medium Pressure Filter Pi 3000 Nominal pressure /315 bar (3040/4570 psi), nominal size up to 400 according to DIN 24550 1. Features High performance filters for modern hydraulic systems Provided for pipe

More information

Block mounting filter, for sandwich plate mounting

Block mounting filter, for sandwich plate mounting Block mounting filter, for sandwich plate mounting RE 51427/01.11 1/16 Type 320PZR025, 075, 125 Size according to DIN 24550: 025 to 125 Nominal pressure 320 bar [4641 psi] Port according to ISO4401 size

More information

SGA and SG-dosers. for SKF DuoFlex dual-line lubrication systems

SGA and SG-dosers. for SKF DuoFlex dual-line lubrication systems SGA and SG-dosers for SKF DuoFlex dual-line lubrication systems Modular and mechanical adjustable SGA and SG-doser are used in SKF DuoFlex applications. SGA and SG-dosers The dosing modules are hydraulically

More information

Oil Filter Module Pi 8300

Oil Filter Module Pi 8300 Oil Filter Module Pi 8300 Volume flow 1 und 220 l/min 1. Features Compact, ready-to connect oil filter module for modern hydraulic and lubrication systems Low noise internal gear pump Minimum loss of performance

More information

Oil Solutions. Phone Fax Low Pressure Filter Pi 150

Oil Solutions. Phone Fax Low Pressure Filter Pi 150 Oil Solutions Phone 0421 336 009 Fax 03 9012 4332 sales@oilsolutionscomau wwwoilsolutionscomau Low Pressure Filter Pi 150 Operating pressure /25 bar, Nominal size up to 630 1 Features Efficient filters

More information

SKF Flowline. for circulating oil lubrication systems

SKF Flowline. for circulating oil lubrication systems SKF Flowline for circulating oil lubrication systems SKF Flowline boosts your circulating oil system s efficiency Circulating oil systems are used in heavy industry for lubrication, cooling and particle

More information

Filtrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181

Filtrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181 Common HYDRAULIC FILTRATION Side wall mounting suction filters Technical Information Connection Ports: 1-1 1/4-1 1/2 BSP (other thread options on request) 1 1/2 SAE J518-3000/M12 Housing Materials: Cover:

More information

Connection Ports: 1/2 1 1/2 BSP (other thread options on request) aluminium alloy NBR (FKM on request)

Connection Ports: 1/2 1 1/2 BSP (other thread options on request) aluminium alloy NBR (FKM on request) HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working (acc. to NFPA T 3.1.5.1): F1-XD4/63/1: 1 bar (15 psi) F1-XD16/25/4: 8 bar (12 psi) Housing Burst (acc. to

More information

High Pressure Filter Pi 410

High Pressure Filter Pi 410 High Pressure Filter Pi 410 Nominal pressure 315 bar (4480 psi), nominal size -63 1. Features High performance filters for modern hydraulic systems Provided for valve block installation Modular system

More information

Air-oil centralized lubrication systems

Air-oil centralized lubrication systems Air-oil centralized lubrication systems A lubrication system should always be as modern and efficient as the machine it is lubricating. Lincoln air-oil systems are ideally suited for this because they

More information

Grease-lubricating pump FF... DSK US (05.05)

Grease-lubricating pump FF... DSK US (05.05) Grease-lubricating pump FF... DSK 2-008-00-US (05.05) electrically operated, for small and medium-sized multiple-line and progressive systems PSG-2 with cycle switch VPB with cycle switch PSG-2 with cycle

More information

Filter elements for microfiltration. Type 46. CELLUDISC filter elements. Features. Contents. RE Edition:

Filter elements for microfiltration. Type 46. CELLUDISC filter elements. Features. Contents. RE Edition: Filter elements for microfiltration Type 46. CELLUDISC filter elements RE 51470 Edition: 2014-08 Size: 10" Maximum pressure differential: 5 bar [73 psi] Filter rating: 2 and 10 μm Operating temperature:

More information

Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T ) Burst 840 bar (12200 psi) (acc. to NFPA T )

Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T ) Burst 840 bar (12200 psi) (acc. to NFPA T ) HYDRAULIC FILTRATION In line medium pressure filters Technical Information Pressure: Max working 280 bar (4000 psi) (acc. to NFPA T 3.10.5.1) Burst 840 bar (12200 psi) (acc. to NFPA T 3.10.5.1) Housing

More information

High Pressure Filter Pi 4230

High Pressure Filter Pi 4230 High Pressure Filter 4230 Nominal pressure 315 bar (4570 psi), nominal size 160 to 400 according DIN 24550 1. Features High performance filters for modern hydraulic systems Modular system Compact design

More information

Series RFLD Duplex In-Line Filter

Series RFLD Duplex In-Line Filter APPLICATION Series RFLD Duplex In-Line Filter Welded Pressures to 230 psi Flows to 3900 gpm HYDAC RFLD in-line filters are designed for in-line mounting and are mainly used in continuously operating systems.

More information

Pressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T ) Buna-N (FKM on request)

Pressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T ) Buna-N (FKM on request) HYDRAULIC FILTRATION Return filters, tank top mounting, inside-to-outside filtration Technical Information Pressure: Max working 8 bar (116 psi) (acc. to NFPA T 3.10.5.1) Burst 16 bar (232 psi) (acc. to

More information

Low Pressure Filter Pi 2000

Low Pressure Filter Pi 2000 Low Pressure Filter Pi 00 Nominal pressure 32/63 bar (460/900 psi), nominal size up to 400 according DIN 24550 1. Features.. High performance filters for modern hydraulic systems Provided for pipe installation

More information

Return-Suction Filters E 068 E 088. In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min e

Return-Suction Filters E 068 E 088. In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min e Return-Suction Filters E 68 E 88 In-line mounting Connection up to G¾ Nominal flow rate up to l/min.8-e Description Application For operation in units with hydrostatic drives, when the return flow is under

More information

Product Series OLA, MV and 161

Product Series OLA, MV and 161 SKF Oil+Air Lubrication Units and Mixing Valves Product Series OLA, MV and 161 For use in SKF Oil+Air Centralized Lubrication Systems Usage and Principle of Operation SKF Oil+Air lubrication units are

More information

Low Pressure Filter Pi 1500

Low Pressure Filter Pi 1500 Low Pressure Filter Pi 500 Nominal pressure /5 bar (40/360 psi), nominal size up to 600 Filter elements according to DIN 4550. Features High performance filters for modern hydraulic systems Provided for

More information

Piston Distributors, Metering Units

Piston Distributors, Metering Units Piston Distributors, Metering Units 1-5001-US For single-line total-loss lubrication systems Group 320 0.01-0.16 ccm Group 321 0.03-0.1 ccm Group 340 0.01-0.16 ccm Group 350 0.1-0.6 ccm Group 390 0.2-1.5

More information

Medium Pressure Filter Pi 360

Medium Pressure Filter Pi 360 Medium Pressure Filter Pi 360 Nominal pressure /315 bar (2990/44 psi), nominal size up to 450 1. Features High performance filters for modern hydraulic systems Provided for pipe installation Modular system

More information

Axial Piston Variable Pump A2VK

Axial Piston Variable Pump A2VK Axial Piston Variable Pump A2VK RE 94001/06.10 1/12 Replaces: 07.04 Data sheet Size 12 to 107 Series 1 and 4 Nominal pressure 250 bar Maximum pressure 315 bar Version for pumping plastic components Contents

More information

Line filter with filter element according to DIN 24550

Line filter with filter element according to DIN 24550 Line filter with filter element according to DIN 2455 RE 51423/9.12 Replaces: 7.1 1/2 Type 445LEN4 to 1 Size according to DIN 2455: 4 to 1 Nominal pressure: 45 bar [6527 psi] Connection up to G 1 1/2;

More information

Low Pressure Filter Pi 200

Low Pressure Filter Pi 200 Low Pressure Filter Pi 0 Nominal pressure 25/63 bar (360/910 psi), nominal size up to 450 1. Features._ High performance filters for modern hydraulic systems Provided for pipe installation Modular system

More information

Vent and bleed filter, water-absorbing. Type BFSK 25 to 125. Contents. Features. RE Edition: Replaces: 05.13

Vent and bleed filter, water-absorbing. Type BFSK 25 to 125. Contents. Features. RE Edition: Replaces: 05.13 Vent and bleed filter, water-absorbing Type BFSK 25 to 125 RE 51456 Edition: 2014-11 Replaces: 05.13 Sizes 25 to 125 Component series 2X Maximum operating pressure 1 bar [14.5 psi] Connection G 3/8 to

More information

lubrication systems CME Electric pump for oil and soft grease volumetric

lubrication systems CME Electric pump for oil and soft grease volumetric lubrication systems CME Electric pump for oil and soft grease volumetric lubrication systems TABLE OF CONTENTS Table of contents 2 Description and technical data 3 Operation and technical data 4 Technical

More information

Inline filter with filter element according to DIN 24550

Inline filter with filter element according to DIN 24550 Inline filter with filter element according to DIN 24550 RE 51421/07.11 Replaces: 12.10 1/16 Type 245LEN0040 to 400; 245LE0130, 0150 Size according to DIN 24550: 0040 to 0400 Additional sizes: 0130, 0150

More information

Low Pressure Filter Pi 200

Low Pressure Filter Pi 200 Low Pressure Filter Pi 0 Nominal pressure 32/63 bar (460/910 psi), nominal size up to 600 1. Features._ High performance filters for modern hydraulic systems Provided for pipe installation Modular system

More information

LMC 301 controller. For reliable control of small, large or multi-system-type lubrication systems

LMC 301 controller. For reliable control of small, large or multi-system-type lubrication systems LMC 301 controller For reliable control of small, large or multi-system-type lubrication systems LMC 301-controlled systems can be configured to verify that lubricant is dispensed LMC 301 controller with

More information

E 068 E 088 In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min

E 068 E 088 In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min Return-Suction Filters E 68 E 88 In-line mounting Connection up to G¾ Nominal flow rate up to l/min Description Application For operation in units with hydrostatic drives, when the return flow is under

More information

Duplex Filter Pi Features. Nominal pressure 200/250 bar (2850/3560 psi), nominal size up to 450

Duplex Filter Pi Features. Nominal pressure 200/250 bar (2850/3560 psi), nominal size up to 450 Duplex Filter Pi 370 Nominal pressure 0/2 bar (28/3560 psi), nominal size up to 0 1. Features High performance filters for modern hydraulic systems _ Modular system Compact design Minimal pressure drop

More information

High Pressure Filter Pi 420

High Pressure Filter Pi 420 High Pressure Filter Pi 4 Nominal pressure 400 bar (5690 psi), nominal size up to 450 optional reverse flow valve 1. Features High performance filters for modern hydraulic systems Modular system Compact

More information

Pressure: Max working F280 D12x port size 1/2 & 3/4 : 420 bar (6000 psi) Burst F280 D12x port size 1/2 & 3/4 : 1260 bar (18000 psi)

Pressure: Max working F280 D12x port size 1/2 & 3/4 : 420 bar (6000 psi) Burst F280 D12x port size 1/2 & 3/4 : 1260 bar (18000 psi) HYDRAULIC FILTRATION F8-D1 series In line medium pressure filters Technical Information Housing Pressure: Max working F8 D1x port size 1/ & 3/4 : 4 bar (6 psi) F8 D1x port size 1 : 3 bar (4 psi) F8 D14x:

More information

Chain lubrication, accessories

Chain lubrication, accessories 1-4106-US Chain lubrication, accessories Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication Im Folgenden finden Sie Informationen zu einem Teil unseres Leistungs- und Serviceportfolios.

More information

Pressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T )

Pressure: Max working 8 bar (116 psi) (acc. to NFPA T ) Burst 16 bar (232 psi) (acc. to NFPA T ) HYDRAULIC FILTRATION Tank top return filters Technical Information Pressure: Max working 8 bar (116 psi) (acc. to NFPA T 3.1..1) Burst 16 bar (232 psi) (acc. to NFPA T 3.1..1) Housing Connection Ports:

More information

By-pass: 1,7 bar (24.6 psi) setting N.B. Cartridge with integrated bypass valve and antidrainback membrane

By-pass: 1,7 bar (24.6 psi) setting N.B. Cartridge with integrated bypass valve and antidrainback membrane HYDRAULIC FILTRATION Spin-on, tank top return filters Technical Information Pressure: Max working 12 bar (175 psi) (acc. to NFPA T 3.10.17) Burst 20 bar (290 psi) (acc. to NFPA T 3.10.17) Connection Ports:

More information

Block mounting filter, lateral flange-mounting possible

Block mounting filter, lateral flange-mounting possible Block mounting filter, lateral flange-mounting possible RE 0/.0 Replaces: 0.09 / Types 0/0 FEN 000 to 000; 0/0 FE 000, 00, 008 Nominal sizes according to DIN 0: 000 to 000 Nominal sizes according to BRFS:

More information

Duplex Filter Pi 3700

Duplex Filter Pi 3700 MAHLE Industrialfiltration is now Filtration Group. For more information, visit www.filtrationgroup.com Duplex Filter Pi 3700 Nominal pressure 0/250/315 bar (2900/36/4570 psi), nominal size up to 400 according

More information

Low Pressure Filter Pi 150

Low Pressure Filter Pi 150 Low Pressure Filter Pi 150 Nominal pressure /25 bar (140/360 psi), nominal size up to 630 1. Features. High performance filters for modern hydraulic systems _ Provided for pipe installation Modular system

More information

High Pressure Filter Pi 4230

High Pressure Filter Pi 4230 High Pressure Filter Pi 4230 Nominal pressure 400 bar (5690 psi), nominal size 160 to 400 according DIN 24550 1. Features High performance filters for modern hydraulic systems Modular system Compact design

More information

Low Pressure Filter Pi 2000/Pi 2200

Low Pressure Filter Pi 2000/Pi 2200 Low Pressure Filter Pi 2000/Pi 2200 Nominal pressure 25 bar (360 psi), nominal size 630 up to 2000 according to DIN 24550 1 Features : HIgh performance filters for modern hydraulic systems Modular system

More information