Headlamp Assembly. Headlamp Bulb Low Beam H4. Headlamp Bulb High Beam H7 REMOVAL AND INSTALLATION Exterior Lighting

Size: px
Start display at page:

Download "Headlamp Assembly. Headlamp Bulb Low Beam H4. Headlamp Bulb High Beam H7 REMOVAL AND INSTALLATION Exterior Lighting"

Transcription

1 Exterior Lighting REMOVAL AND INSTALLATION Headlamp Assembly 3. Remove the rubber boot from the lamp back face. WARNING: Bulbs become hot to touch and can cause burns if not allowed to cool before handling. 1. Raise the hood. 2. Disconnect the 3 lamp wiring connectors. 3. Remove the front bumper & bumper absorber (Refer to section ). 4. Remove 4 bolts from the lamp. 5. Pull lamp slighty forward and upwards to dislodge retainers. 6. Gently move lamp slightly inboard and rock forward to remove ensuring indicator bulb clears fender opening. 1. Connect lamp wiring harness. 2. Reverse removal procedure. 3. Check and adjust headlamp aim if necessary. Headlamp Bulb High Beam H7 1. Switch the headlamps off and allow sufficient time 2. Disconnect wiring from the bulb closest to the centre of the vehicle. 4. Release retaining spring clip and withdraw bulb. 5. Remove bulb from holder. NOTE: Hold the replacement Quartz Halogen bulb with a clean cloth or tissue to prevent contact with glass. If the glass is touched, the skin s natural oils will contaminate the bulb. Wipe the bulb clean using methylated spirits before installing. 1. Push bulb into holder. 2. Install the bulb and retain it with the spring clip. 3. Install the rubber boot, installing the inner aperture to the bulb first, followed by the outer aperture to the lamp body. Ensure the rubber boot has sealed correctly and is not deformed. 4. Reconnect wiring to the bulb and test. Headlamp Bulb Low Beam H4 1. Switch the headlamps off and allow sufficient time 2. Disconnect wiring from bulb. 3. Remove the rubber boot from the lamp back face. 4. Release retaining spring clip and withdraw bulb. NOTE: Hold the replacement Quartz Halogen bulb with a clean cloth or tissue to prevent contact with glass. If the glass is touched, the skin s natural oils will contaminate the bulb. Wipe the bulb clean using methylated spirits before installing. 1. Install the bulb and retain it with the spring clip. 2. Install the rubber boot, installing the inner aperture to the bulb first, followed by the outer aperture to the lamp body. Ensure the rubber boot has sealed correctly and is not deformed. 3. Reconnect wiring to the bulb and test. G86735 en

2 Exterior Lighting Turn Signal Bulb 1. Turn the front wheel inward to allow access to the 3 lower front fender splash shield push pin rivets and screw. Carefully peel back the splash shield to expose the turn signal wiring connector. Auxiliary Lamp 1. Switch the lamps off and allow sufficient time to cool. 2. Remove the lower air deflector from the front bumper. 1 Fender splash shield 2 Firtree Cip - 6.5x25mm (x2) 3 Scrivets - 6mm (x10) 1 Wiring harness 4 Screw - 5mm (x1) 2 Self-tapping screw 5 Screw - 5mm (x2) 3 Firtree clip 2. Turn the bayonet-style connector anti-clockwise 4 Air deflector retaining screw approximately 1/8 of a turn to free the bulb holder. 3. Disconnect the wiring harness from the lamp bulb. 4. Remove the three self-tapping screws used to retain the lamp. Parklamp Bulb 1. Switch the headlamps off and allow sufficient time Auxiliary Lamp Bulb 2. Gently rotate anticlockwise and pull bulb holder from the lamp. NOTE: Switch the lamps off and allow sufficient time 1. Remove the lower air deflector from the bottom of the front bumper. 2. Disconnect the terminal. 3. Remove the bulb retainer by rotating in an anti-clockwise direction. 4. Remove the bulb from the bulb by pulling outwards. 1. Install the new bulb. 2. Refit the bulb retainer into the lamp housing and rotate 1/8 turn clockwise until the bulb retainer is fully positioned. Note that the bulb retainer will 3. Remove bulb from the holder by pulling outwards. only fit correctly in one position. 3. Connect the terminal to the bulb retainer. G86741 en

3 Exterior Lighting Refit the lower air deflector. Tail Lamp Assembly Sedan Fog Lamp 1. Switch the foglamps off and allow sufficient time 2. Remove the air lower air deflector. 3. Push the lamp inward with your palm. 4. Disconnect the lamp wiring. 5. Remove the lamp assembly from the car. Fog Lamp Bulb 1. Remove the foglamp assembly from the bumper 1. Open decklid. as above. 2. Remove interior quarter trim. 3. Disconnect wiring connector to tail lamp and squeeze rubber grommet through hole. 4. Remove two retaining screws on the inboard side of tail lamp assembly. 5. Insert a thin flat head screwdriver or similar object having a flat blade to the forward side of the outboard stud and gently prise it off the plastic retainer, being careful to protect any paint from damage. 6. Remove the lamp assembly. 7. Discard mating ball stud insert. 1. Replace plastic ball stud insert. 2. Unclip retaining clip and remove bulb. 2. Pull the wiring assembly in and ensure the rubber grommet is correctly seated to body panel. NOTE: Hold the replacement Quartz Halogen bulb 3. Install lamp into vehicle ensuring locating tab is with a clean cloth or tissue to prevent contact with over the sheetmetal tab. glass. If the glass is touched, the skin s natural oils 4. Install the two retaining screws. will contaminate the bulb. Wipe the bulb clean using 5. Connect the wiring connector and refit the rear methylated spirits before installing. quarter interior trim. 1. Install the bulb and retain it with the spring clip. 6. Close the decklid. 2. Test. 3. Clip lamp insert into the lamp assembly. G86741 en

4 Exterior Lighting Tail Lamp Assembly Wagon Tail Lamp, Reverse Lamp and Rear Indicator Bulb Sedan And Wagon 1. Open the liftgate. 1. Follow steps 1, 4, 5 of Tail Lamp Assembly and procedure, so that lamp assembly is free from vehicle. It is not necessary to disconnect the electrical wiring from vehicle. 2. Remove the rear quarter interior trim. 3. Disconnect wiring connector to tail lamp and squeeze rubber grommet through hole. 4. Remove the two retained screws, one on the inboard side and another one on the top of the tail lamp assembly. 5. Insert a thin flat head screwdriver or similar object having a flat blade to the forward side of the outboard stud and gently prise it off the plastic retainer, being careful to protect any paint from damage. 2. Remove bulb holder from socket by rotating holder anti-clockwise approximately 1/8th turn until free from socket. Stop and tail lamp - (clear twin filaments bulb) Indicator lamp - (amber bulb) Reverse lamp - (clear bulb) 3. Remove bulb from holder by rotating 6. Remove the tail lamp assembly. anti-clockwise approximately 1/8th turn. 1. Pull the wiring assembly in and ensure the rubber 1. Install bulb in holder by gently pushing bulb into grommet is correctly seated to body panel. holder and rotating bulb clockwise. 2. Insert the locating peg to the upper inboard 2. Insert bulb and holder assembly into socket. Note: square hole on the body panel and push the the holder cannot be inserted into the incorrect outboard stud into the plastic retainer. socket. Rotate holder clockwise until firm in 3. Install the two retained screws. socket. 4. Connect the wiring connector and refit the rear 3. Follow the procedure given in this section for quarter interior trim. installation of the tail lamp assembly. 5. Close the liftgate. Tail Lamp Assembly Style Side Box 1. Open tailgate. 2. Remove two bolts on taillight edge. G86747 en

5 Exterior Lighting Remove lamp, pulling away at 45 degrees. 2. Carefully insert the tail lamp assembly, snapping the two retaining tabs into place. 3. Install the two bolts. Reverse Light Replacement Style Side Box 1. Remove the two bolts attaching the reverse light. 1 Bolt (x2) 2 Tail lamp wiring 3 Tail lamp pin location guide 4 Tail lamp assembly 4. Disconnect wiring. 1. Reverse removal procedure. 1 Reverse lamp Rear Light Bulbs Replacement Style 2. Carefully insert a flat blade under the lens. Side Box 3. Disconnect the bulb connector. 1. Remove the two bolts from the inside of the tailgate. 2. Carefully pull the tail lamp assembly from the liftgate pillar by releasing the two retaining tabs. 4. Remove the bulb to be replaced. 1. Insert a new bulb and replace the wiring connector. 2. Replace the lens and install the two bolts. Tail Lamp Assembly Tray 1. Remove M6 nuts from lamp mounting bracket. 1 Brake/Tail lamp 2 Indicator lamp 3. Disconnect the wiring connector. 4. Carefully pull out the bulb to be replaced. 1. Insert the new bulb and replace the wiring connector. G86747 en 1 Tail lamp assembly 2 Nut - M6

6 Exterior Lighting Rear Light Bulbs Replacement Cable/Chassis and Tray 1. Release the retaining clip and swivel aside the plastic frame that secures the lens. 1 Bolt 2 Nut - M6 3 Tail lamp assembly 1 Reversing lamp 2 Indicator lamp 3 Tail lamp 4 Brake lamp 2. Remove the lens from the lamp assembly. 3. Remove the blown bulb by gently pressing the bulb down and turning it anti-clockwise. 1. Insert a new bulb, replace the lens and close the plastic frame with the retaining clip. Licence Plate Lamp Assembly 4 Ute chassis 5 Mointing bracket 1. Gently insert a flat blade or similar object under one side of lamp assembly and gently press on the locking tab. 2. Lift the lamp assembly out of the bumper or applique. 3. Disconnect the wiring connector. G86752 en

7 Exterior Lighting Rear Licence Plate Lamp Replacement 1. Connect the wiring connector. Chassis/Cab and Tray 2. Position lamp assembly and push into bumper or applique until locking tabs engage. Licence Plate Bulb 1. Remove lamp assembly as above leaving the wiring connected. 2. Turn bulb holder approximately 1/8th turn anti-clockwise until it is free. 3. Pull bulb out from socket. NOTE: Tabs prevent the bulb holder from being inserted into the lamp assembly at the incorrect orientation. Do not apply force. Rear Licence Plate Lamp Replacement Style Side Box and 1. Carefully insert a flat blade under one side of the lamp assembly. Press gently on the locking tab. and 1. Push off the rubber band and pull off the cap. 1 Retaining bolt 2 Licence plate housing 2. Remove the bulb by gently pressing it down and turning it anti-clockwise. 3. Insert a new bulb and replace the cap in the rubber band. Side Indicator Lamps 1. Turn front wheel outward. 2. Remove front splash shield fixings behind wheel, and peel splash shield back. 2. Lift the lamp assembly out of the bumper. 3. Disconnect the wiring connector. 4. Turn the bulb holder approximately 1/8th turn anti-clockwise until it is free. Pull the bulb from the socket. 5. Replace the bulb and bulb holder, connect the wiring connector and push the lamp assembly into the bumper until the locking tabs engage. 1 Fender splash shield 2 Firtree Cip - 6.5x25mm (x2) 3 Scrivets - 6mm (x10) 4 Screw - 5mm (x1) 5 Screw - 5mm (x2) G86752 en

8 Exterior Lighting Remove bulb holder by turning anti-clockwise 2. Disconnect wiring connector to stop lamp. about 45 degrees. 4. Remove bulb from holder by pulling straight out. High Mount Stop Lamp Sedan (Except LWB) 1. From inside the luggage compartment remove the bulb holder from the base of the lamp. 2. From inside the vehicle remove the parcel shelf trim. 3. Gently prise the lamp from the panel, dislodging the front legs first. 1. Slot rear hooks of lamp into panel, then snap in front legs. 2. Replace the trim. 3. Install the bulb holder in the lamp. NOTE: There is no bulb fitted to holder when a spoiler mounted HMSL is fitted. 3. Unscrew lamp assembly from spoiler. NOTE: Lamp is a sealed unit and must be replaced as a complete assembly. High Mount Stop Lamp Bulb Wagon 1. Raise the liftgate and detach the clip-on cover from the lamp. 2. Detach the bulb holder from the lamp. High Mount Stop Lamp XR Series Sedan 1. Unbolt rear spoiler and lift from bootlid. G86760 en 1 High mount stop lamp 2 Screw receptacle 3 Screw 4 High mount brake light lens 5 High mount brake light housing 6 Tail gate 3. Remove the wedge base bulb from the bulb holder. 1. Install the bulb in the bulb holder. 2. Install the bulb holder in the lamp. 3. Install the cover on the lamp.

Bulb Renewal TOP ACCESS COVER

Bulb Renewal TOP ACCESS COVER TOP ACCESS COVER To gain access to the headlight units, the top cover must be removed. Unscrew and remove the six fasteners (A). Remove the top cover. After changing the defective bulb, refit the cover,

More information

FRAME AND BUMPERS 13-1 FRAME AND BUMPERS TABLE OF CONTENTS

FRAME AND BUMPERS 13-1 FRAME AND BUMPERS TABLE OF CONTENTS WJ FRAME AND BUMPERS 13-1 FRAME AND BUMPERS TABLE OF CONTENTS BUMPERS... 1 FRAME... 5 BUMPERS TABLE OF CONTENTS DESCRIPTION AND OPERATION BUMPERS...1 AND FRONT FASCIA...1 FRONT ABSORBER...2 REAR FASCIA...2

More information

Bulb Replacement REPLACING BULBS

Bulb Replacement REPLACING BULBS Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's

More information

LAMPS 8L - 1 LAMPS CONTENTS

LAMPS 8L - 1 LAMPS CONTENTS TJ LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 16 HEADLAMP ALIGNMENT... 5 LAMP BULB SERVICE... 8 LAMP DIAGNOSIS... 1 LAMP SERVICE... 11 LAMP SYSTEMS... 15 LAMP DIAGNOSIS INDEX GENERAL INFORMATION GENERAL

More information

Lighting GENERAL INFORMATION. Daytime running lamps. Condensation. Stop lamps. Halogen headlamps. Reversing lamps. Bi-Xenon headlamps

Lighting GENERAL INFORMATION. Daytime running lamps. Condensation. Stop lamps. Halogen headlamps. Reversing lamps. Bi-Xenon headlamps Lighting GENERAL INFORMATION There are three types of headlamp systems: Halogen high/low beam main lamp with a fill-in high beam halogen lamp alongside. Bi-xenon high/low beam main lamps with fill-in high

More information

Bulb Renewal OVERVIEW

Bulb Renewal OVERVIEW Bulb Renewal OVERVIEW It is important that only Jaguar bulbs of the type specified are used when renewing bulbs. Before renewing bulbs, switch off the ignition and light switches. Top cover To gain access

More information

900 Installation instructions. SCdefault

900 Installation instructions. SCdefault SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction

More information

Lights TURN SIGNAL/PARKING LIGHT HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT. Maintenance

Lights TURN SIGNAL/PARKING LIGHT HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT. Maintenance Check the operation of your car s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car s visibility and the ability to signal your intentions to

More information

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No ) ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES

More information

Lights TURN SIGNAL/SIDE MARKER LIGHT/ PARKING LIGHT HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT CONTINUED FOG LIGHT. Maintenance 257

Lights TURN SIGNAL/SIDE MARKER LIGHT/ PARKING LIGHT HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT CONTINUED FOG LIGHT. Maintenance 257 Check the operation of your car s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car s visibility and the ability to signal your intentions to

More information

LAMPS 8L - 1 LAMPS CONTENTS

LAMPS 8L - 1 LAMPS CONTENTS NS LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 25 EXTERIOR LAMP BULB SERVICE... 9 EXTERIOR LAMP SERVICE... 14 HEADLAMP ALIGNMENT... 5 INTERIOR LAMPS... 18 LAMP DIAGNOSIS... 1 LAMP DIAGNOSIS INDEX GENERAL

More information

Lights CONTINUED TURN SIGNAL/SIDE MARKER LIGHT HEADLIGHT PARKING LIGHT. Maintenance 237

Lights CONTINUED TURN SIGNAL/SIDE MARKER LIGHT HEADLIGHT PARKING LIGHT. Maintenance 237 Check the operation of your car s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car s visibility and the ability to signal your intentions to

More information

R8 Exhaust Installation Guidelines

R8 Exhaust Installation Guidelines STāSIS Engineering R8 Exhaust Installation Guidelines Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti

More information

Chapter 12 Electrical system

Chapter 12 Electrical system 12 1 Chapter 12 Electrical system Contents Aerial - removal and refitting..............................23 Auxiliary warning system components - removal and refitting....15 Bulbs (exterior lamps) - renewal.............................5

More information

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown. 2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR

More information

LAMP BULB SERVICE TABLE OF CONTENTS

LAMP BULB SERVICE TABLE OF CONTENTS 8L - 6 LAMPS XJ LAMP BULB SERVICE TABLE OF CONTENTS AND FRONT POSITION LAMP BULB...6 SIDE REPEATER LAMP BULB...6 AND FRONT POSITION LAMP BULB REAR FOG LAMP BULB...7 LICENSE PLATE LAMP BULB...7 (3) Pull

More information

GT and OUTBACK models Low beam 12V 55W H1 High beam 12V 60W 9005 (HB3) Except GT and OUTBACK models 12V 65/55W 9007 (HB5)

GT and OUTBACK models Low beam 12V 55W H1 High beam 12V 60W 9005 (HB3) Except GT and OUTBACK models 12V 65/55W 9007 (HB5) Maintenance and service Replacing bulbs HB5019EB Wattage Bulb No. 1 Headlight GT and OUTBACK models Low beam 12V 55W H1 High beam 12V 60W 9005 (HB3) Except GT and OUTBACK models 12V 65/55W 9007 (HB5) 2

More information

1. General Description

1. General Description EXERIOR/INERIOR RIM GENERAL DESCRIPION 1. General Description A: COMPONEN 1. FRON GRILLE EI-00413 Front grille Front grille emblem Clip 2. UNDER COVER EI-00414 Under cover Clip (side) ightening torque:

More information

Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools:

Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools: Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item #53611 Installation Time: 1 Day Required tools: Phillips Screw driver 10mm Socket + Ratchet/Wrench 8mm Socket + Ratchet/Wrench 5mm Socket + Ratchet/Wrench

More information

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :40-05 Sep

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :40-05 Sep SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction

More information

5 Mechanisms and accessories

5 Mechanisms and accessories 5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT 59A SAFETY ACCESSORIES

More information

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag. Part Number: 343870 F/Kit 17557 Product Deluxe Combination Winch and Non Winch Bull Bar Description: Suited to Nissan XTERRA 05ON USA Only vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;

More information

SCdefault. 900 Installation instructions

SCdefault. 900 Installation instructions SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part

More information

REVi RX-8 Intake. RX-8 REVi Intake System I PN Installation Instructions. Tools Required:

REVi RX-8 Intake. RX-8 REVi Intake System I PN Installation Instructions. Tools Required: RX-8 REVi Intake System PN 18299 Installation Instructions I-18299 Tools Required: Small/Stubby Phillips head screwdriver Small flat head screwdriver Medium Phillips head screwdriver 10mm socket and ratchet

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (DX, HX, VP) 2005 CIVIC 2- AND 4- DOOR AII 27865-30866 Issue Date SEP 2005 NOTE: Fog Lights cannot be installed if the vehicle is equipped

More information

2006 Jeep Commander ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Service Information - Commander

2006 Jeep Commander ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Service Information - Commander REMOVAL BULB Fig. 58: Remove/Install Rear Lamp Unit Bulbs NOTE: The rear lamp unit (1) contains four bulbs. For domestic vehicles they are: backup (2), park/stop (3), park/turn signal (4) and rear side

More information

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf) Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well

More information

Lighting GENERAL INFORMATION. Daytime running lamps. Halogen headlamps. Stop lamps. Bi-Xenon headlamps. Reversing lamps

Lighting GENERAL INFORMATION. Daytime running lamps. Halogen headlamps. Stop lamps. Bi-Xenon headlamps. Reversing lamps Lighting GENERAL INFORMATION There are three types of headlamp systems: Halogen high/low beam main lamp with a fill-in high beam halogen lamp alongside. Bi-xenon high/low beam main lamps with fill-in high

More information

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: 2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness

More information

LAMPS 8L - 1 LAMPS CONTENTS

LAMPS 8L - 1 LAMPS CONTENTS PL LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 8 LAMP BULB SERVICE... 2 LAMP DIAGNOSIS... 1 LAMP SERVICE... 5 LAMP DIAGNOSIS HEADLAMP LEVELING MOTOR... 1 INDEX HEADLAMP LEVELING MOTOR This vehicle

More information

Trim (general) Lower A-pillar trim, removing and installing

Trim (general) Lower A-pillar trim, removing and installing Page 1 of 16 70-72 Trim (general) Lower A-pillar trim, removing and installing - To remove, remove A-pillar bolts 4 (2x). Tightening torque: 1.5 Nm (13 in. lb) - Remove door seal -2- in area of A-pillar

More information

Saab 9-3 CV M04-, 4D/5D M06-

Saab 9-3 CV M04-, 4D/5D M06- SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2004 S2000 AII 26323-31611 Issue Date DEC 2005 PARTS LIST Rear defroster switch Hardtop 3-Pin subharness (If equipped, not used) 4-Pin subharness

More information

M-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS

M-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176 2005 CR-V Issue Date P/N 08V31-S9A-114 SEP 2004 PARTS LIST 25 Wire ties Left fog light 6 Washer-bolts Right fog light 6 Spring

More information

Trim panels on model 124 as of 07/

Trim panels on model 124 as of 07/ amb def Installation Instructions Trim panels on model 124 as of 07/93 88.07 The trim panels in the ET scope of supply are primed and can be painted before installation to match the vehicle color in accordance

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-S0X-100 1999-2001 ODYSSEY AII 20677 Issue Date AUG 1999 PARTS LIST 2 Fog lights Switch Fuse label Right bracket Relay B, 4-pin

More information

1. General Description

1. General Description EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,

More information

Window Regulator: Service and Repair Front Door Trim. Armrests. With Power Windows. Front Door Arm Rest. Remove or Disconnect

Window Regulator: Service and Repair Front Door Trim. Armrests. With Power Windows. Front Door Arm Rest. Remove or Disconnect 1995 Oldsmobile Cutlass Ciera V6-3100 3.1L VIN M SFI Page 1 Window Regulator: Service and Repair Front Door Trim Armrests 1. Plugs from upper and lower armrest openings. 2. Screws from upper and lower

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S Application 2010 INSIGHT Publications No. AII 40881 Issue Date MARCH 2009 PARTS LIST Right fog light bracket D Fog Lights Kit P/N 08V31-TM8-100 Left fog light Fog

More information

Page 1 of 33 SPECIFICATIONS 2013 Ford Edge 3.5L Eng Limited Print Date: TORQUE SPECIFICATIONS Description Nm lb-ft lb-in Assist handle bolts 9-80 B-pillar upper trim panel screw 9-80 C-pillar trim panel

More information

Front Grille Replacement

Front Grille Replacement Document ID: 4298678 Page 1 of 1 2017 Cadillac XT5 XT5 Service Manual Europe, Korea, N America, Other IO 9325297 Document ID: 4298678 Front Grille Replacement Front Grille Replacement Preliminary Front

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (LX, EX) CIVIC 2- AND 4- DOOR AII 25449 Issue Date SEP 2003 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional

More information

FOG-LAMPS INSTALL KIT

FOG-LAMPS INSTALL KIT FOG-LAMPS INSTALL KIT DODGE RAM (BR, BE) Installation Instructions Read entire instructions thoroughly before starting. For proper removal and installation, follow procedures in the service manual. NOTES:

More information

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent

More information

Deuce/Ace Installation Instructions

Deuce/Ace Installation Instructions HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ELEMENT AII 24318 Issue Date DEC 2002 PARTS LIST Trailer Hitch Kit P/N 08L92-SCV-100 4 Bolts, 12 x 35 mm Trailer hitch U-bolt 2 Nuts,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176-28932 2005 CR-V Issue Date S P/N 08V31-S9A-115 FEB 2005 PARTS LIST 6 Washer-bolts Left fog light 6 Spring nuts Harness bracket

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)

More information

Removing fixtures and fittings. Work description. Seats. BeGe. Seat assembly. Seat base, G and P cabs Remove the parts as follows:

Removing fixtures and fittings. Work description. Seats. BeGe. Seat assembly. Seat base, G and P cabs Remove the parts as follows: Seats BeGe Seat assembly 1. Tap down the lock tabs on the seat base and turn the pins 90 degrees, pull out the pins. 2. Remove the electrical connections to the seat base and backrest heaters. 1 3. Lift

More information

FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH

FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH 761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip

More information

SECTION 9B LIGHTING SYSTEMS

SECTION 9B LIGHTING SYSTEMS SECTION 9B LIGHTING SYSTEMS CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

4. BODY REPAIR. White Body. Without sunroof. With sunroof BODY REPAIR ACTYON SM CHANGED BY EFFECTIVE DATE AFFECTED VIN

4. BODY REPAIR. White Body. Without sunroof. With sunroof BODY REPAIR ACTYON SM CHANGED BY EFFECTIVE DATE AFFECTED VIN 12 5110 4. White Body Without sunroof With sunroof 5110 13 Body Dimensions Side Structure Complete Unit: mm INT EXT REPAIR 14 5110 Engine Compartment Unit: mm 5110 15 Front End Unit: mm INT REPAIR EXT

More information

FOG LAMPS INSTALL KIT

FOG LAMPS INSTALL KIT FOG LAMPS INSTALL KIT PT CRUISER INSTALLATION INSTRUCTIONS Read entire instructions thoroughly before starting. For proper aiming of fog lamps, follow procedures in the service manual. NOTES: Left and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Toyota Tundra Kit 76380 (Black) and 76381 (Stainless) Your safety, and the safety of others, is very important. To help you make informed

More information

Chapter 12 Body electrical systems

Chapter 12 Body electrical systems 12 1 Chapter 12 Body electrical systems Contents Anti-theft alarm system - general information 24 Battery check and maintenance See Chapter 1 Battery - removal and refitting See Chapter 5 Bulbs (exterior

More information

SAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard

SAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: 2013-2014 Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: Fog light (Left& Right) 2 Flat head & Phillips screwdriver Upper grille with surround 1 Ratchet & Socket set OR Lower grille

More information

Drive shaft left-hand side, replace

Drive shaft left-hand side, replace "VCC126387 EN 20090226" file://c:\info\vv132007\ie\en\30\vcc126387.htm Page 1 of 13 Drive shaft lefthand side, replace Special tools: 9995681 Removal Removing the drive shaft nut the hub cap the drive

More information

TOYOTA PRIUS C FOG LIGHT (Halogen & LED)

TOYOTA PRIUS C FOG LIGHT (Halogen & LED) TOYOTA PRIUS C 2012-14 FOG LIGHT (Halogen & LED) Part Number: TPC-312 / TPC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide

More information

1 of 2 5/17/17, 1:22 PM

1 of 2 5/17/17, 1:22 PM 1 of 2 5/17/17, 1:22 PM Trim Molding, Removing and Installing Special tools, testers and auxiliary items required Wedge Set (T10383) Removal Wedge (T40233) Removing - Starting at the front, pry the trim

More information

Installation Instructions for C & R Heat Exchanger Removal of Factory Unit

Installation Instructions for C & R Heat Exchanger Removal of Factory Unit Installation Instructions for C & R Heat Exchanger Removal of Factory Unit Remove the 8 clips that retain the upper radiator shroud. Remove the shroud. Remove the coolant tank cap from the heat exchanger

More information

Product Deluxe Combination Winch and Non Winch Bull Bar, Flare and Non Flare Description: Suited to Nissan D40T Navara XC DC SC 2008 ON WARNING

Product Deluxe Combination Winch and Non Winch Bull Bar, Flare and Non Flare Description: Suited to Nissan D40T Navara XC DC SC 2008 ON WARNING Part Number: 343840 & 343850 F/Kit 617501 Product Deluxe Combination Winch and Non Winch Bull Bar, Flare and Non Flare Description: Suited to Nissan D40T Navara XC DC SC 008 ON vehicle/s: WARNING REGARDING

More information

TOYOTA SIENNA FOG LIGHT (Halogen & LED)

TOYOTA SIENNA FOG LIGHT (Halogen & LED) (Halogen & LED) Part Number: TSI-312 / TSI-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application CR-V Publications No. AII 32953-34081 Issue Date NOV 2006 PARTS LIST 2 Corner sensor clips Backup Sensor Attachment Kit P/N 08V67-SWA-100A Back-up sensor

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

Ground Effects, P/N: (V6), (V8)

Ground Effects, P/N: (V6), (V8) , P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 28603 S 2006 RIDGELINE Issue Date FEB 2005 PARTS LIST Relay Fog Light Kit P/N 08V31-SJC-100 Right fog light 15 Wire ties Left fog light

More information

HAYMAN REESE PART No: 03099RW BMW X4 F26 Series May 2014 Onwards INSTALLATION INSTRUCTIONS

HAYMAN REESE PART No: 03099RW BMW X4 F26 Series May 2014 Onwards INSTALLATION INSTRUCTIONS PART No: 03099RW BMW X4 F26 Series May 2014 Onwards PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT PLACE THESE INSTRUCTIONS IN THE VEHICLE S GLOVEBOX AFTER INSTALLATION IS COMPLETED

More information

JEEP WRANGLER. K 2x. G 12x. N 8x. Front Bumper # AD, , AC, AB and AB. Kit # , AB

JEEP WRANGLER. K 2x. G 12x. N 8x. Front Bumper # AD, , AC, AB and AB. Kit # , AB Kit # 82209740AD JEEP WRANGLER Front umper #82209740AD, 82211715, 82210341A, 82211716 82211715A and 82211716A Kit # 82211715, 82211715A A L 1 D 4x I F 1 D 4x I F N 8x G 1 4x See steps 1-11, then proceed

More information

Chapter 12 Body electrical system

Chapter 12 Body electrical system Chapter Body electrical system Contents Air bag system - general information, precautions and system de-activation.......................................... Air bag system components - removal and refitting.............

More information

TOYOTA PRIUS FOG LIGHT (Halogen or LED)

TOYOTA PRIUS FOG LIGHT (Halogen or LED) Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item

More information

Short Shifter Installation Instructions Miata 6-Speed manual

Short Shifter Installation Instructions Miata 6-Speed manual Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter

More information

PONTIAC FIREBIRD

PONTIAC FIREBIRD 1974-78 PONTIAC FIREBIRD Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 LED panel mount kits 6 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal

More information

INVISIHITCH. Hidden Hitch Receiver for. BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit)

INVISIHITCH. Hidden Hitch Receiver for. BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit) INVISIHITCH Hidden Hitch Receiver for BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit) Capacity: 7,700 lbs. Towed Weight / 600 lbs Tongue Weight* *

More information

FITTING OF (WESTFALIA) REMOVABLE TOWBAR ON SKODA OCTAVIA WITHOUT TOWBAR PREPARATION (04/11/16 CJ v1.0)

FITTING OF (WESTFALIA) REMOVABLE TOWBAR ON SKODA OCTAVIA WITHOUT TOWBAR PREPARATION (04/11/16 CJ v1.0) FITTING OF (WESTFALIA) REMOVABLE TOWBAR ON SKODA OCTAVIA 2013+ WITHOUT TOWBAR PREPARATION (04/11/16 CJ v1.0) A. INTRO ALL STEPS COMPLETED AT YOUR OWN RISK! I AM NOT LIABLE FOR ANY LOSS OR DAMAGE! These

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 36765 S 2008 RIDGELINE Issue Date JUN 2007 PARTS LIST Relay Fog Light Kit P/N 08V31-SJC-100 Right fog light 15 Wire ties Left fog light

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD AII 24050 4-DOOR P/N 08V31-SDA-100 Issue Date AUG 2002 NOTE: The outside temperature gauge cannot be installed in a vehicle with

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece

More information

Lamp TABLE OF CONTENTS. Bulb Specifications and Functional Check Location of Exterior Lamps Interior Lamps...

Lamp TABLE OF CONTENTS. Bulb Specifications and Functional Check Location of Exterior Lamps Interior Lamps... Lamp TABLE OF CONTENTS Bulb Specifications and Functional Check... - Location of Exterior Lamps... - Interior Lamps...- BULB SPECIFICATIONS AND FUNCTIONAL CHECK BULB SPECIFICATIONS (ACTYON) Exterior Interior

More information

Lamp TABLE OF CONTENTS

Lamp TABLE OF CONTENTS TABLE OF CONTENTS Bulb Specifications and Functional Check...13-2 Location of Exterior Lamps...13-3 Replacing the Exterior Lamps...13-4 Replacing the Interior Lamps...13-6 13 Lamp 1 2 3 4 5 6 7 8 9 10

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S Application 2012 CIVIC 4-DOOR Publications No. AII 45623 Issue Date APR 2011 PARTS LIST Fog Light Kit P/N 08V31-TR0-100B (without automatic lights) P/N 08V31-TR0-100C

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26033 KIT 2004 ODYSSEY Issue Date JAN 2004 PARTS LIST Trailer Hitch: P/N 08L92-S0X-100 Heavy-Duty P/S Cooler Kit P/N 53765-S0X-305 Heavy-duty

More information

RIM Hood For Aeromaster Bodies

RIM Hood For Aeromaster Bodies RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28593 2006 RIDGELINE P/N 08F23-SJC-100 Issue Date FEB 2005 PARTS LIST Center front bumper trim (Not used if the vehicle is equipped

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic

More information

Installation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors)

Installation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors) Installation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors) Pre installation check list: - Double check vehicles data with TUV certificate -

More information

Product ARB SAHARA BAR (suitable for up 12000lb winch) Suited to TOYOTA LANDCRUISER LC200 SERIES 2012 ON WARNING

Product ARB SAHARA BAR (suitable for up 12000lb winch) Suited to TOYOTA LANDCRUISER LC200 SERIES 2012 ON WARNING Part Number: 39550 F/Kit 67347 Product ARB SAHARA BAR (suitable for up 000lb winch) Description: Suited to TOYOTA LANDCRUISER LC00 SERIES 0 ON vehicle/s: Optional Fitting kits: For vehicles fitted with

More information

LED Fog Light. Conflicts Note: 1226, General Applicability Fits Models Additional Items Required For Installation

LED Fog Light. Conflicts Note: 1226, General Applicability Fits Models Additional Items Required For Installation LED Fog Light Year & Model Part Number Conflicts Note: 1226, 1228 2017 Prius TPR-817 General Applicability Fits Models 1221 1225 1223 1227 1224 Additional Items Required For Installation Items 1 N/A 2

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SNA-100 2008 CIVIC 4-DOOR AII 37730 Issue Date AUG 2007 PARTS LIST Fog light harness Right fog light Left fog light Sub harness

More information

Wheel Arch Trim Set. Installation Manual. This section covers installation of the wheel arch trim set.

Wheel Arch Trim Set. Installation Manual. This section covers installation of the wheel arch trim set. Wheel Arch Trim Set FORESTER Wheel Arch Trim Set EN PART # E20SSG000 This section covers installation of the wheel arch trim set. Installation Manual Note: Before performing installation, be sure to read

More information

SCdefault. 900 Monteringsanvisning

SCdefault. 900 Monteringsanvisning SCdefault 900 Monteringsanvisning SITdefault Towbar MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part No. Replaces

More information

Item C& D Not Applicable C

Item C& D Not Applicable C GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: KIT CONTENTS: LED Fog Lamp Upgrade Rogue Sport 999F1 V4001 A B Item C& D Not Applicable C D Do

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2012 ODYSSEY Publications No. AII 46755 Issue Date SEP 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100

More information

5 Mechanisms and accessories

5 Mechanisms and accessories 5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR ACCESSORIES 57A INTERIOR ACCESSORIES 59A SAFETY

More information

Mazda CX-9. Trailer Wiring Harness Fitting Instructions

Mazda CX-9. Trailer Wiring Harness Fitting Instructions Towbar Kit Part No: TCACTB Harness Kit Part No: TCACTWH Towbar Fitting Time: 5 minutes Harness Fitting Time: 0 minutes Trailer Wiring Harness Fitting Instructions FI Doc No: FI5 - Issue: - 08/0/6 Lumen

More information

Installing the STS-4CH Dodge Challenger Sequential Turn Signal System

Installing the STS-4CH Dodge Challenger Sequential Turn Signal System Installing the STS-4CH 2008-2010 Dodge Challenger Sequential Turn Signal System The STS-4CH is an exciting addition to your 2008-2010 Dodge Challenger. This Plug-N-Play system comes complete with pre-wired

More information