60.07 Style 233 Restrained Flexible Coupling For Dynamic Joint Deflection
|
|
- Harold Bates
- 5 years ago
- Views:
Transcription
1 Style 33 Restraine Flexible Coupling For Victaulic Bolte Split-Sleeve Proucts (VBSP) Style 33 carbon steel restraine couplings (formerly Depen-O-Lok FxF Moifie) provie a fully restraine, flexible pipe joint that satisfies the requirements set forth by the AWWA C7 Stanar for Bolte, Split-Sleeve Restraine an Non-Restraine Couplings for Plain-En. This style of coupling is typically use in burie or expose pipe applications for fiel joint connections where joint flexibility an thrust restraint is require. Style 33 couplings are esigne to allow for ynamic (in-service) joint eflection an are most commonly use in pairs outsie of a structure to accommoate ifferential settlement between the structure an the pipeline. The Style 33 couplings can also allow for up to 1"/5 mm of axial pipe movement at the joint ue to thermal pipe movement. Typical applications inclue water an wastewater treatment pipelines, force main an water transmission piping, an burie piping connections outsie of valve vaults or other structures (when couplings are use in pairs at a minimum). The couplings provie ease of installation an come stanar with an epoxy coating for protection against corrosion. The use of a heat-shrink sleeve or tape system can be use with minimal effort ue to the low profile configuration. The ual-arche mechanical coupling boy houses the o-ring gaskets that provie a raial seal aroun the circumference of the pipe, while a sealing plate provies for the axial seal across the coupling boy an pipe joint. The Style 33 coupling incorporates a restraint ring wele to each pipe en (furnishe with the coupling), allowing the coupling housing to strale the restraint rings an confining the rings uner the coupling boy in orer to prevent joint separation. The coupling housing an restraint ring wels are esigne to accommoate hoop stress an en loas to meet system pressure requirements. Style 33 restraine couplings also perform at negative pipe pressures up to full vacuum. The o-ring gasket is not pressure responsive an therefore oes not require internal pipe pressure to assist with the seal. The arche cross-sectional esign provies stiffness to resist forces encountere uring negative pressure (submerge) or vacuum service. Style 33 couplings are available in stanar nominal sizes from 8 144"/ mm, with other sizes available base on esign an application requirements. The Style 33 restraine coupling can accommoate operating pressures up to psi/065 kpa (with higher pressure available) epening on the actual pipe iameter an wall thickness. For pressures an sizes not shown in the imension an performance tables contact Victaulic for information on our engineere proucts by visiting our web site. All flexible mechanical couplings shoul be properly supporte to minimize or eliminate unesirable loas at the joint. support requirements are efine within the Victaulic Application Guielines ocument. Please see publication 6.0. For proper closure tool selection see column marke Tool Type on pages "/ mm JOB/OWNER CONTRACTOR ENGINEER System No. Submitte By Spec Sect Para Location Date Approve Date VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _1
2 Style 33 Restraine Flexible Coupling For PRODUCT GUIDE Prouct Style Guie Submittal Number Style Number Coupling/Boy Material Application Carbon Steel Non-Rrestraine Coupling S Stainless Steel Non-Rrestraine Coupling Carbon Steel Expansion Coupling S Stainless Steel Expansion Coupling Carbon Steel Restraine Coupling S Stainless Steel Restraine Coupling 33 Carbon Steel Restraine Coupling For S Stainless Steel Restraine Coupling For Carbon Steel Restraine Single-Gasket Coupling S Stainless Steel Restraine Single-Gasket Coupling SEGMENTED COUPLINGS The Style 33 imension tables list the minimum number of coupling housing segments for a particular pipe size. For special applications, restraine couplings are available in two (or more) segments to allow for installation of the coupling over an existing pipe joint or to facilitate ease of hanling for larger size couplings. The o-ring gaskets (except Silicone) can be furnishe split to allow for fiel boning when an existing pipe joint configuration oes not allow for installation of a complete o-ring onto the pipe en. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _
3 Style 33 Restraine Flexible Coupling For BODY TYPE Cross-Section NOTE: Boy type is not optional an will be etermine by system requirements. Type coupling is a shoulere coupling. This is a heavy uty coupling to accommoate higher pressures for certain pipe iameters. The shoulers wele to the ege of the coupling boy provie a vertical bearing surface for the restraint rings an provie aitional cross-sectional stiffness. The limit rings on the insie of the coupling boy ensure that any axial movement or ynamic joint eflection is istribute across the coupling between both sies of the joint. COUPLING COMPONENTS 1. Boy Dual arch cross-section.. Shoulers Provie aitional stiffness, allow for larger o-ring gasket an provie vertical bearing surface for restraint rings. 3. Closure Plates Low profile bolt pas for installation an tightening of coupling; gap between plates of installe coupling allows for fiel flexibility. 4. Sealing Plate Provies axial seal across the coupling boy an pipe joint. 5. O-ring Gaskets Provie circumferential seal. 6. Fasteners Stus High Strength Threae Ro Nuts Heavy Hex Nuts Washers SAE small pattern flat washers 7. Restraint Rings Attache to pipe ens to create a restraine joint ONE SEGMENT HOUSING TWO SEGMENT HOUSING VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _3
4 Style 33 Restraine Flexible Coupling For MATERIAL SPECIFICATIONS Boy Carbon Steel conforming to ASTM A36 or ASTM A1011 (for gauge thicknesses) Shoulers Carbon Steel conforming to ASTM A36 Closure Plates Carbon Steel conforming to ASTM A36 Sealing Plate Stainless Steel conforming to ASTM A40 316L O-ring Gaskets Stanar (Specify choice on orer): EPDM -30ºF to +30ºF/-34ºC to +110ºC Col an hot water within allowable temperature range; ilute acis; excellent resistance to the eteriorative effects of ozone, oxygen, heat an most chemicals not involving hyrocarbons. NOT RECOMMENDED FOR PETROLEUM SERVICES. Silicone -30ºF to +350ºF/-34ºC to +177ºC Dry, hot air applications; excellent resistance to many chemicals. NOT RECOMMENDED FOR HOT WATER OR STEAM APPLICATIONS. Isoprene -40ºF to +160ºF/-40ºC to +71ºC Water; salt water; sewage; goo resistance to oxygen an ilute acis Services liste are general service recommenations only. Refer to a chemical elastomer guie for specific applications an suitability of gasket material for services that are not liste. Optional gasket (specify choice on orer): Nitrile -0ºF to +180ºF/-8ºC to +8ºC Water; petroleum proucts, vegetable an mineral oils; air with oil vapors within allowable temperature range; goo resistance to hyrocarbons; acis an bases. Fluouroelastomer +0ºF to +ºF/-7ºC to +149ºC Outstaning resistance to heat an most chemicals. Neoprene -30ºF to +180ºF/-34ºC to +8ºC Water an wastewater; goo resistance to ozone, effects of UV an some oils. Services liste are general service recommenations only. Refer to a chemical elastomer guie for specific applications an suitability of gasket material for services that are not liste. Restraint Rings Carbon Steel conforming to ASTM A108 Grae 1018 Fasteners Stus - Carbon Steel conforming to ASTM A193 Grae B7 zinc plate. Optional: Stainless Steel conforming to ASTM A193 Grae B8M 316 Class Nuts - Heavy hex nuts Carbon Steel conforming to ASTM A194 Grae H zinc plate Optional: Stainless Steel conforming to ASTM A194 Grae 8M 316 Washers - Carbon Steel SAE small pattern flat washers conforming to ASTM F436 SAE pattern zinc plate Optional: Stainless Steel Type 316 SAE pattern. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _4
5 Style 33 Restraine Flexible Coupling For LININGS AND COATINGS Stanar (specify choice on orer): Liqui Epoxy: Liqui epoxy is applie per AWWA C10, 16 mils minimum DFT an is NSF61 approve. Epoxy can be applie as a primer for fiel applie top coat where UV protection ue to sunlight exposure is require. This coating offers excellent corrosion protection for burie applications. A supplemental corrosion protection system such as heat shrink sleeve or tape coat system is recommene for burie applications. Fusion Bone Epoxy: Fusion bone epoxy is applie with an electrostatic spray system using a long cure epoxy power that offers excellent chemical resistance an corrosion protection. Fusion bone epoxy is applie per AWWA C13, 1 mils minimum DFT an is NSF61 approve. Optional (specify choice on orer): Phenolic Alky Primer: Phenolic Alky primer is a lea-free an chromate-free, fast-rying, corrosion-resistant primer that accepts a variety of high-performance topcoats, but is not recommene for immersion service by itself. This primer system is typically applie at to 3 mils DFT. Other Coating Systems (Available Upon Request): A water base enamel coating is available. This paint offers an aesthetic coating for minimal protection, short-term installations or where corrosion protection is not a consieration. Fusion bone nylon for chemical an abrasion resistance, as well as other coatings such as organic zinc primers an hot ippe galvanizing may also be available. PIPE END DIMENSIONAL TOLERANCE AND OVALITY For specific pipe iameter tolerances, pipe ovality (rounness) requirements an minimum/maximum pipe iameter allowance, refer to the tables inclue in the Installation Manuals (below) an 6.0 Application Guielines. I-33.S1 - Styles 33/33S Restraine Flexible Coupling For (Type, One-Segment) I-33.S - Styles 33/33S Restraine Flexible Coupling For (Type, Two-Segments) VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _5
6 Style 33 Restraine Flexible Coupling For DIMENSIONS 1-SEGMENT (1) () (3) Coupling Dimensions (4) (5) (6) NominaI Actual O.D. Range Boy Thickness With () 1.50 Min. No. of Coupling Segments No. of Fasteners - Fastener Dimensions Dia. x Length x Approximate Weight Each Lbs/Kg ga ga ga / ga / / / / / /8 x / /8 x /8 x / 8-1 x /8 x / 8-1 x (1) Couplings must be use on pipe with a minimum wall thickness that meets the requirements of AWWA C00 for carbon steel pipe. () For actual O.D. roun own to the nearest " to etermine proper coupling size require. (3) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. (4) 1-segment couplings may be available as -segment couplings to allow for in-place pipe installations. Contact Victaulic for etails. (5) Coupling weights are base on nominal pipe iameter an inclue all accessories. Weight may vary base on actual size of pipe. (6) Closure Tool Recommenations:* B= CTM-0 Large Manual Closure Tool C= CTH Ton Hyraulic Closure Tool *For more etails on closure tools refer to page 15. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. Boy Type Tool Type B,C B,C B,C B,C B,C B,C B,C C B,C C B,C C B,C C C B,C C C C C C C C C -SEGMENT VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _6
7 Style 33 Restraine Flexible Coupling For DIMENSIONS 1-SEGMENT (1) () (3) Coupling Dimensions (4) (5) (6) NominaI Actual O.D. Range Boy Thickness With () 1.50 Min. No. of Coupling Segments No. of Fasteners - Fastener Dimensions Dia. x Length x Approximate Weight Each Lbs/Kg /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x (1) Couplings must be use on pipe with a minimum wall thickness that meets the requirements of AWWA C00 for carbon steel pipe. () For actual O.D. roun own to the nearest " to etermine proper coupling size require. (3) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. (4) 1-segment couplings may be available as -segment couplings to allow for in-place pipe installations. Contact Victaulic for etails. (5) Coupling weights are base on nominal pipe iameter an inclue all accessories. Weight may vary base on actual size of pipe. (6) Closure Tool Recommenations:* B= CTM-0 Large Manual Closure Tool C= CTH Ton Hyraulic Closure Tool *For more etails on closure tools refer to page 15. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. Boy Type Tool Type C C C C C C C C C C C C C C C C C C C C C C C C C -SEGMENT VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _7
8 Style 33 Restraine Flexible Coupling For DIMENSIONS 1-SEGMENT (1) () (3) Coupling Dimensions (4) (5) (6) NominaI Actual O.D. Range Boy Thickness With () 1.50 Min. No. of Coupling Segments No. of Fasteners - Fastener Dimensions Dia. x Length x Approximate Weight Each Lbs/Kg /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x /8 x / 8-1 x x (1) Couplings must be use on pipe with a minimum wall thickness that meets the requirements of AWWA C00 for carbon steel pipe. () For actual O.D. roun own to the nearest " to etermine proper coupling size require. (3) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. (4) 1-segment couplings may be available as -segment couplings to allow for in-place pipe installations. Contact Victaulic for etails. (5) Coupling weights are base on nominal pipe iameter an inclue all accessories. Weight may vary base on actual size of pipe. (6) Closure Tool Recommenations:* B= CTM-0 Large Manual Closure Tool C= CTH Ton Hyraulic Closure Tool *For more etails on closure tools refer to page 15. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. Boy Type Tool Type C C C C C C C C C C C C -SEGMENT VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _8
9 Style 33 Restraine Flexible Coupling For PERFORMANCE Nominal Carbon Steel (1) () (3) (3) (4) (5) Ductile Iron Stainless Steel Boy Type En Separation Min - Max Max. Allow. Deflection Degrees Max. Permissible En Loa lbf/n ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' (1) For allowable test or transient pressure, the maximum working pressure may be increase to 1½ times the values shown. () allowable axial pipe movement at the joint is the ifference between the maximum an minimum pipe en separation. At maximum pipe en separation, axial movement can only occur via pipe expansion into the joint an vice versa. (3) en movement an eflection are non-concurrent. (4) Publishe eflection values are intene an available for both static (installe) an ynamic (in-service) joint eflection. The coupling closure shoul be locate 90 egrees from the irection of joint eflection. (5) The maximum permissible en loas liste in the table are calculate using the nominal pipe OD. The actual maximum permissible en loa will be less or greater than the publishe figures epening on the actual pipe OD. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _9
10 Style 33 Restraine Flexible Coupling For PERFORMANCE Nominal Carbon Steel (1) () (3) (3) (4) (5) Stainless Steel Ductile Iron En Separation Min - Max Max. Allow. Deflection Degrees Max. Permissible En Loa lbf/n Boy Type ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' (1) For allowable test or transient pressure, the maximum working pressure may be increase to 1½ times the values shown. () allowable axial pipe movement at the joint is the ifference between the maximum an minimum pipe en separation. At maximum pipe en separation, axial movement can only occur via pipe expansion into the joint an vice versa. (3) en movement an eflection are non-concurrent. (4) Publishe eflection values are intene an available for both static (installe) an ynamic (in-service) joint eflection. The coupling closure shoul be locate 90 egrees from the irection of joint eflection. (5) The maximum permissible en loas liste in the table are calculate using the nominal pipe OD. The actual maximum permissible en loa will be less or greater than the publishe figures epening on the actual pipe OD. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _10
11 Style 33 Restraine Flexible Coupling For PERFORMANCE Nominal Carbon Steel (1) () (3) (3) (4) (5) Stainless Steel Ductile Iron En Separation Min - Max Max. Allow. Deflection Degrees Max. Permissible En Loa lbf/n 738 Boy Type ' ' ' ' ' ' ' ' ' ' ' ' (1) For allowable test or transient pressure, the maximum working pressure may be increase to 1½ times the values shown. () allowable axial pipe movement at the joint is the ifference between the maximum an minimum pipe en separation. At maximum pipe en separation, axial movement can only occur via pipe expansion into the joint an vice versa. (3) en movement an eflection are non-concurrent. (4) Publishe eflection values are intene an available for both static (installe) an ynamic (in-service) joint eflection. The coupling closure shoul be locate 90 egrees from the irection of joint eflection. (5) The maximum permissible en loas liste in the table are calculate using the nominal pipe OD. The actual maximum permissible en loa will be less or greater than the publishe figures epening on the actual pipe OD. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _11
12 Style 33 Restraine Flexible Coupling For RESTRAINT RINGS (1) () Restraint Ring (3) (4) Back Wel - Must not exten past the back ege of the restraint ring L Type - Restraint Ring Location LC E En S Restraint Ring Single Flare Bevel Groove Wel Detail E En S Restraint Ring Double Flare Bevel Groove Wel Detail L Nominal Boy Type With () Diameter () Location (L) / / Wel (E) 3/3 3/3 3/3 3/3 3/3 3/3 3/3 3/3 3/3 3/3 3/3 5/3 5/3 (1) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. () For applications other than air or gas, where a liqui or other meium is flowing through pipe, restraint ring wel requirements are as follows: Type couplings require a full circumferential ouble flare bevel groove wel base on the wel sizes shown in the table. For low pressure air or gas applications, where the weight of the meium flowing through the pipe is not a consieration, a single flare bevel groove wel an/or less than a full circumference of wel may be allowe to attach the restraint rings. Contact Victaulic for specific etails. Each restraint ring shipment inclues restraint ring placement an weling ata that is specific to application or project requirements. (3) Restraint rings must be wele perpenicular to the pipe axis with a tolerance of L± 1/16"/1.6 mm. (4) Flare bevel groove wel size in table is the minimum requirement. Depth of preparation S = () ; Wel size E S * 0.65 per AWS D1.1. For a ouble flare bevel groove wel, the wel on the back sie of the restraint ring must not exten beyon the outermost ege of the ring. The coupling shouler must have unrestricte contact with the ring an the pipe O.D. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _1
13 Style 33 Restraine Flexible Coupling For RESTRAINT RINGS (1) () Restraint Ring (3) (4) Back Wel - Must not exten past the back ege of the restraint ring L Type - Restraint Ring Location LC E En S Restraint Ring Single Flare Bevel Groove Wel Detail E En S Restraint Ring Double Flare Bevel Groove Wel Detail L Nominal Boy Type With () Diameter () Location (L) / / / / / / / / Wel (E) (1) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. () For applications other than air or gas, where a liqui or other meium is flowing through pipe, restraint ring wel requirements are as follows: Type couplings require a full circumferential ouble flare bevel groove wel base on the wel sizes shown in the table. For low pressure air or gas applications, where the weight of the meium flowing through the pipe is not a consieration, a single flare bevel groove wel an/or less than a full circumference of wel may be allowe to attach the restraint rings. Contact Victaulic for specific etails. Each restraint ring shipment inclues restraint ring placement an weling ata that is specific to application or project requirements. (3) Restraint rings must be wele perpenicular to the pipe axis with a tolerance of L± 1/16"/1.6 mm. (4) Flare bevel groove wel size in table is the minimum requirement. Depth of preparation S = () ; Wel size E S * 0.65 per AWS D1.1. For a ouble flare bevel groove wel, the wel on the back sie of the restraint ring must not exten beyon the outermost ege of the ring. The coupling shouler must have unrestricte contact with the ring an the pipe O.D. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _13
14 Style 33 Restraine Flexible Coupling For RESTRAINT RINGS (1) () Restraint Ring (3) (4) Back Wel - Must not exten past the back ege of the restraint ring L Type - Restraint Ring Location LC E En S Restraint Ring Single Flare Bevel Groove Wel Detail E En S Restraint Ring Double Flare Bevel Groove Wel Detail L Nominal Boy Type With () Diameter () Location (L) / / / / Wel (E) (1) For allowable test or transient pressure, the maximum working pressure may be increase to 11/ times the values shown. () For applications other than air or gas, where a liqui or other meium is flowing through pipe, restraint ring wel requirements are as follows: Type couplings require a full circumferential ouble flare bevel groove wel base on the wel sizes shown in the table. For low pressure air or gas applications, where the weight of the meium flowing through the pipe is not a consieration, a single flare bevel groove wel an/or less than a full circumference of wel may be allowe to attach the restraint rings. Contact Victaulic for specific etails. Each restraint ring shipment inclues restraint ring placement an weling ata that is specific to application or project requirements. (3) Restraint rings must be wele perpenicular to the pipe axis with a tolerance of L± 1/16"/1.6 mm. (4) Flare bevel groove wel size in table is the minimum requirement. Depth of preparation S = () ; Wel size E S * 0.65 per AWS D1.1. For a ouble flare bevel groove wel, the wel on the back sie of the restraint ring must not exten beyon the outermost ege of the ring. The coupling shouler must have unrestricte contact with the ring an the pipe O.D. Note: The ata in this table only applies when carbon steel couplings are being use on carbon steel pipe. 5/3 7/3 5/3 7/3 5/3 7/3 5/3 7/3 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _14
15 Style 33 Restraine Flexible Coupling For CLOSURE TOOLS MANUAL TOOL Manual Tools CTM-01: for use on 5" an 8" boy withs CTM-0: for use on 10" boy withs for use on 1" boy withs with thickness of 3/16" or less Hyraulic Tools CTH-01*: for use on 1" boy withs with thickness of " or greater for use on 14", 16" an 18" boy withs CTH-0: for use on all type 3 couplings Hyraulic tool package comes stanar with: one (1) tool hea one (1) hyraulic cyliner one (1) hyraulic hose one (1) han pump * A CTH-01 hyraulic closure tool can be use in applications where the CTM-0 manual closure tool is recommene. Note: The closure tools liste above are esigne specifically for Victaulic Style 30, 31, 3 an 33 couplings. If orering custom prouct, contact Victaulic for appropriate tool selection. HYDRAULIC TOOL VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED. _15
16 Style 33 Restraine Flexible Coupling For PRODUCT CONFIGURATOR C S D E P S S0 Actual O.D. * Boy PSI/kPa Rubber Class Style Inches^ Fraction Type Segments Rating Compoun Paint C through ¼ ½ ¾ 88 7/8 S Carbon 1 One Two A 5/170 B 50/345 C 75/515 D /690 E 160 F /1035 G 175/ H 00/1375 J 50/175 K /056 E EPDM I Isoprene L Silicone T Nitrile V Neoprene O Fluoroelastomer ^ Couplings are available in a range of nominal sizes from 8 144". * For actual pipe O.D. roun own to the nearest " to etermine proper coupling size require. Harware Ring an Material F Fusion S Carbon SO Carbon bone epoxy X Stainless Steel Ring on P Orange G Galvanize Carbon Steel enamel T Shop primer DO Carbon B Liqui epoxy Steel Ring on N Fusion Ductile Iron bone nylon G Galvanize XO- Stainless Steel Ring on 0 None Stainless Steel ENGINEERED PRODUCTS OPTIONS For non-stanar proucts the Victaulic Engineere Proucts group can assist with specialty joints esigne to meet the specific size, pressure an temperature requirements of your system. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for etails. NOTE This prouct shall be manufacture by Victaulic or to Victaulic specifications. All proucts to be installe in accorance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change prouct specifications, esigns an stanar equipment without notice an without incurring obligations. TESTING Victaulic Style 33 couplings are esigne to allow for a 50 percent increase over the publishe maximum working pressure for test an/or transient pressures. Due to the huge volume of air that can be involve in jobsite air testing an the nature of air or gas that is pressurize, jobsite air testing shoul be limite to 5 psi/175 kpa or less. Victaulic offers a ishe hea assembly prepare with a restraint ring for the Style 33 coupling for fiel testing a section of pipeline or to en a pipeline an allow for future expansion. Contact Victaulic for etails. For complete contact information, visit 586 REV K UPDATED 08/013 VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. 013 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
60.08 Style 233S Restrained Flexible Coupling For Dynamic Joint Deflection
Style 33S Restraine Flexible Coupling Victaulic Bolte Split-Sleeve Proucts (VBSP) Style 33S stainless steel restraine couplings (formerly Depen-O-Lok FxF Moifie) provie a fully restraine, flexible pipe
More information60.03 Style 231 Non-Restrained Flexible Expansion Coupling
Style 31 Non-Restraine Flexible Victaulic Bolte Split-Sleeve Proucts (VBSP) Style 31 carbon steel expansion couplings (formerly Depen-O-Lok FxE) provie a non-restraine, flexible pipe joint that is esigne
More informationStyle 234 Restrained Flexible Single-Gasket Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date
Victaulic Bolted Split-Sleeve Products (VBSP) Style 234 carbon steel couplings (formerly Depend-O-Lok Air/FluidMaster) are single-arch couplings that are commonly used in buried or exposed steel pipe applications
More informationAngular contact ball bearings
Angular contact ball bearings 7200 BE CB Y HC5 Nomenclature 1 2 3 4 1. esign: 2. Clearance: 3. Cage esigns: B BE A E NR N2 2Z 2RS1 40 contact angle 40 contact angle, high capacity, all ISO corners Conra
More informationQuickVic Rigid Coupling for Steel. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE GROOVED COUPLINGS
H ONL. SEE PAGE 4 FOR DETAILS. The patented Style 107 rigid coupling joins 12"/50 300 standard roll grooved and cut grooved steel pipe. The joint is assembled without disassembling the bolts, nuts, gasket
More informationDeep groove ball bearings
Deep groove ball bearings 6200-2 J/C3 HC5 GJN Nomenclature 1 2 3 4 5 1. Seals, shiels & snap rings: 2. Cage esigns: 4. Suffix: RSH RS2 RSL R 2RSH 2RS2 2RSL 2R 2 NR Contact seal of synthetic rubber (NBR)
More informationHousing Coating: Orange enamel. Hot dipped galvanized. Optional Bolts/Nuts: (Available in imperial size bolts and nuts only.)
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS The patented Style 107H rigid coupling joins 8"/50 200 standard roll grooved and cut grooved steel pipe.* The joint is assembled without disassembling the bolts,
More informationHot dipped galvanized. Optional Bolts/Nuts: (Available in imperial size bolts and nuts only.)
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS The Style 177 QuickVic flexible coupling is installation-ready, and joins 2-8"/50-200 standard roll grooved and cut grooved steel pipe. The coupling's unique
More informationThe Ideal Locking Devices For Shaft-to-Hub Connections. Proven Design. Easy To Use
C-ROM Sizing Software ETP Keyless Shaft Mount Connections The Ieal ocking evices For Shaft-to-Hub Connections. ETP Connections are ieal for positioning an locking shaft components in a system. They are
More informationFOR EVERYTHING ENCLOSURE
FOR EVERYTHING ENCLOSURE PVC EDGE PROTECTOR Provies excellent protection for steel eges 9 styles available Simple to install SEE PAGES 498-499 DRAWER SLIDES Available in light, meium an heavy uty Full
More informationISO 9001:2008 LOCKING ASSEMBLIES SHRINK DISCS KEYLESS RIGID COUPLINGS
OCKING ASSEMBIES SHRINK DISCS KEYESS RIGID COUPINGS Introuction ISO 9001:2008 CIMAX Metal Proucts Company & MAV S.p.A. A Unique Partnership In June 2011, CIMAX entere an exclusive agreement with MAV S.p.A.
More informationOther materials are available on request. Operating conditions
Merkel U-Ring T 18 Merkel U-Ring T 18 Asymmetrical sealing lip POM back-up ring PUR profile ring Profile ring Coe Harness Polyurethane 95 AU V142 95 Shore A Fig. 1 Merkel U-Ring T 18 Back-up ring Polyacetal
More informationPipe bracket spacing and support of pipelines
Pipe an support of pipelines General Pipe support for plastics pipes Plastic pipe systems shoul be installe using supports esigne for use with plastics an shoul then be installe taking care not to amage
More informationGrooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
More information08.08 Vic-Check Valves
The check valves are a product of computer-assisted innovative engineering with quality features including a new hydrodynamically efficient profile. The Vic-Check valve utilizes a spring-assisted, single-disc
More informationCouplings. Ductile Iron Housing Specifications. Coatings. Gasket Specifications. Bolt/Nut Specifications
Figure 71 Flange Adapters (ANSI Class 5/150) The Figure 71 Flange Adapter is capable of pressures up to 300 psi (20,7 bar) depending on pipe size and wall thickness. It provides a direct transition from
More informationGrooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
More informationØ range <500 mm. Ø range >500 mm. Operating conditions. Surface quality. Surface roughness R a R max
Hyraulics Ro Seals Merkel U-Ring T 20 Merkel U-Ring T 20 Merkel U-Ring T 20 PUR profile ring Material range
More informationGrooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
More informationHigh-Performance Servo-Worm Reducers Input and Output Couplings for Servo-Worm Reducers 18. Selection and Ratings for Servo-Worm Reducers 19 22
Table of Contents Page High-Performance Servo-Worm Reucers 7 17 Input an Output Couplings for Servo-Worm Reucers 18 Selection an Ratings for Servo-Worm Reucers 19 22 Mounting, Maintenance an Spare Parts
More informationRod ends, series K (wide version), internal and external thread. Rod ends, series E (slim version), internal and external thread
Ro Ens an Spherical earings Overview Ro ens, series K (wie version), internal an external threa Page Maintenance free, plastic Ø 5-20mm... Lubricateable (S), steel Ø 2-40mm... Maintenance free (T), steel
More informationPRODUCTS FOR THE HYDRAULICS INDUSTRY
PROUCTS FOR THE HYRAULICS INUSTRY SPIRALGUAR SPIRALGUAR High Performance Hose an Cable Protection How to calculate quantity: Outsie iameter of hose Length (m) of hose Insie iameter of Spiralguar X to be
More informationFord Fabricated Steel Products
Ford Fabricated Steel Products Section N2 12/2000 The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487 Overseas
More informationVolute Centrifugal Pumps PN 16 / PN 25 for Heat Transfer Media Thermal Oil up to 350 C Hot Water up to 204 C. Series NTWH/CTWH process model
Volute Centrifugal s PN 16 / PN 25 for Heat Transfer Meia Thermal Oil up to 350 C Hot Water up to 20 C Series NTWH/CTWH process moel Series NTWH/CTWH Series NBWH/CBWH block moel Series NIWH/CIWH in-line
More informationRotameters. Variable Area Flow Meters
Variable Area Flow Meters Rotameters General Size: ⅜ 2½ Total Flow Range:. 264 gpm Tube Material: PA, PSU, PVC transparent Seal: EPDM, FPM Float: PVDF, PVDF-HP transparent En Connection: Solvent cement
More informationFULL COMPLEMENT NEEDLE BEARINGS
FULL OMPLEMENT NEELE EARINGS Technical features Full complement neele bearings These bearings are available with or without an inner ring from 12 bore size. Stanar complete bearings type NA have an inner
More informationSEE VICTAULIC PUBLICATION FOR DETAILS
dapters SEE VICTULIC PULICTION 10.01 FOR DETILS Style 741 Style 741 adapter is designed for directly incorporating flanged components with NSI CL. 125 or CL. 150/PN10 and PN16 or ustralian Standard Table
More informationPressure Relief Valve Overflow Valve Type DHV 715 Type DHV 716 Type DHV 725
Pressure Relief Valve Overflow Valve Type DHV Type DHV Type DHV DIBt* approve DIBt* approve High repeating accuracy, with union sockets or spigot ens Print / The optimal monitoring valves Sizes up to Operating
More informationShyam Enterprises 5 HEAT EXCHANGERS
Shyam Enterprises HEAT EXCHANGERS 33 Heat Exchangers Introuction The overall heat transfer coefficient of borosilicate glass equipment compare favourably with many alternative process plant construction
More informationTechnical features. Cam followers
AM FOLLOWERS Technical features am followers Naella cam followers are esigne to run irectly on various types of surface such as cams, ramps an slieways. In orer to satisfy the operating conitions impose
More informationCOMPANY PROFILE. Our products have been supplied to local and foreign customers for the following industries:
CECK VAVES COMPANY PROFIE The company ARMATURY Group a.s. is a leaing Czech manufacturer an istributor of inustrial valves, fittings an control systems for valves. The annual prouction is of more than
More informationSplit pillow blocks
Definition an capabilities 638 Series 639 Variants 639 Design criteria: loas an torques 640 Installation/Assembly criteria: seal selection 641 Characteristics 642 Pillow block housing for bearings with
More informationStyle 99 Roust-A-Bout Couplings
R IPS CARBON STEEL PIPE PLAIN END SYSTEM Style 99 Roust-A-Bout Couplings 14.02 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION 1 1 / 2-12" Sizes 14-18" Sizes Style 99 Roust-A-Bout couplings
More informationStainless Steel Pipe System. System No. Submitted By Spec Sect Para Location Date Approved Date TEMPERATURE ( F/ C)
The Victaulic Vic-Press 304 System for joining approved Type 304/304L stainless steel pipe provides a fast, easy, clean, reliable means for joining 1/2"/15, 3/4"/20, 1"/25, 1 1/2"/40, and 2"/50 stainless
More informationRexnord Tollok Locking Assemblies
Tollok Catalog ownloa the most up-to-ate version at www.rexnor.com/ocumentation Rexnor Tollok Locking Assemblies Why Choose Rexnor Tollok Locking Assemblies? Why Choose Rexnor? When it comes to proviing
More informationmechanical coupling system
mechanical coupling system R Since 1981 Depend-O-Lok has offered engineers, contractors, OEM s and system owners an improved pipeline coupling system. Depend-O-Lok products offer strength, longterm reliability,
More informationForged Steel Valves. Gate / Globe / Check. DHV Industries, Inc. DHV Valve Company Inc.
3451 Pegasus Drive Bakersfiel, CA 93308 U.S.A. Call Toll Free: (877) DHV-USA1 Phone: (661) 392-8948 Fax: (661) 392-8947 E-mail: sales@hvinustries.com Website: www.hvinustries.com DHV Valve Company Inc.
More informationStarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines
Joint Restraint Products StarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines INFORMATION StarFlex Flexible Expansion Joints can deflect
More informationPoly16 Plus Compression Fittings Technical information
1 Poly16 Plus Compression Fittings Technical information Materials Boy, Thrust ring: polypropylene copolymer stabilize (PP-B), UV stabilize Nut: polypropylene copolymer stabilize (PP-B) with Master Batches
More informationE2ER/E2ERZ. Reduce Failures From Cutting Oil Ingress. Features. Applications. Patent Pending Heat-Sealing Method
Oil-resistant Proximity Sensors Reuce Failures From Cutting Oil Ingress Fluororesin cable withstans cutting oil Sealing metho eliminates gaps at cable joints Resin filling blocks ingress IP67G* egree of
More informationLenntech Tel Fax
SEE VICTAULIC PUBLICATIO.01 FOR DETAILS Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide a strong component for joining plain and beveled end, including Schedule steel
More informationTechnical handbook Compression Fittings and Clamp Saddles
Technical hanbook 2009 Compression Fittings an Clamp Sales 1 Poly16 Plus Compression Fittings Technical information Materials Boy, Thrust ring: polypropylene copolymer stabilize (PP-B), UV stabilize Nut:
More informationSeries 709 Butterfly Valves (175 psi/1270 kpa)
IPS CARBON STEEL PIPE GROOVED VALVES Series 709 Butterfly Valves (175 psi/1270 kpa) 08.03 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION The Series 709 grooved end butterfly valve offers
More informationTriple row axial angular contact ball bearings
Triple row angular contact ball bearings Series DKLF Heavy Series Features Bearings of series DKLF with a bore iameter of 30 mm an 40 mm are available in a Heavy series. This allows the user to achieve
More informationElectrofusion Fittings & Specialist Tooling
Electrofusion Fittings & Specialist Tooling September 2016 (4.0mm pin) introuction Plasson Electrofusion Fittings Plasson fittings are specifically esigne for reliable, high performance pipe joining an
More informationVic-Strainer WARNING. System No. Submitted By Spec Sect Para Location Date Approved Date IPS CARBON STEEL PIPE - GROOVED ACCESSORIES SERIES 730
Series 730 Vic-Strainer is lighter than flanged Y type strainers and provides straightthrough flow for lower pressure drop. It installs with two Victaulic couplings, and is rated up to 750 psi/5175 kpa
More information08.12 Vic-Plug Balancing Valve
Series 377 Vic-Plug balancing valve is the only eccentric grooved end plug valve made specifically for throttling services. For 3 12"/80 300 systems, Victaulic Style 307 transition couplings are available
More informationHIGH PRESSURE - hydraulic cylinders
SSU - hyraulic cyliners A, type aterial: rotective coating: eium: ax. piston spee : ax. working press.: Carb. steel an cast iron (hea) U,, O, T rimer (option), chromiumplate yraulic oil 0.5 m/s 200 From
More informationFAX FAX
2 seals on eman HERCULES SEALS ON EMAN provies a wie selection of custom, cost effective sealing solutions using avance rapi-prototype technology. The programmable CNC prouction cell can manufacture both
More informationInformation. Plate Cylinder Type C(L)KU32. HIGH type. (Magnetic field resistant auto switch) New. New. New Newly added guide pins
Information Pin lamp yliners ompact yliner Type (L)G32 Magnetic fiel resistant auto switch mounting type LOW type (-X81) HIGH type (-X82) Plate yliner Type (L)U32 Magnetic fiel resistant auto switch mounting
More informationFIG Gruvlok Flange Adapter
FIG. 88 Gruvlok Adapter The Gruvlok Fig. 88 Adapter allows for direct connection of Class 125 or Class 150 flanged components to a grooved piping system. The Gruvlok Adapter provides an alternative method
More informationCOMPACT BEARING CR 2000
COMPACT BEARING CR 2000 Unreinforce elastomeric bearing loaable up to 20 N/mm² Bearing esign Contents Page Bearing esign formulae 2 Prouct escription 2 Shape factors 3 How to specify 3 Shear stiffness
More informationSeries 706 Butterfly Valves (300 PSI/2065 kpa)
IPS CARBON STEEL PIPE GROOVED VALVES Series 706 Butterfly Valves (300 PSI/2065 kpa) 08.17 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION The Series 706 grooved end butterfly valve offers
More informationREQUEST PUBLICATION 18.11
* SEE VICTALIC PBLICATION 10.01 FOR DETAILS The Victaulic Pressfit 316 System for joining approved Type 316/316L stainless steel pipe provides a fast, easy, clean, reliable means for joining ½"/15, ¾"/
More informationShaft Diameter d 1 3 /16 01 B /4 01 B /16 01 B /2 01 B /16 01E B /4 01E B
Lubrication Fittings Lubrication points are tappe 1/4 NPT or 1/8 NPT epening on size an series, an fitte with nipples for grease lubrication as stanar. nipples may be remove an replace with other fittings
More informationASV sturdy and robust construction. DN 10 up to DN bar (PN 10) at 20 C. DMV 755: 1,0-9,0 bar DMV 765: 0,5-9,0 bar
Pressure Reucing Valve Type DMV Type DMV Print-No. / Design Size Max. Pressure Setting Range Pressure Setting Working Pressure Back lash Operating Security Maintenance Simple inline pipe connection ASV
More informationANSI VALVE CATALOGUE
ANSI VAVE CATAOGUE GATE VAVES GOBE VAVES CHECK VAVES BA VAVES BUTTERFY VAVES SYSTEMS AND PRODUCTS FOR INDUSTRIA CARGO TRANSFER AND STORAGE ANSI VAVE CATAOGUE Introuction CTS has evelope itself into a reputable
More informationSeries W709 AGS Butterfly Valves (175 psi/1270 kpa)
IPS CARBON STEEL PIPE GROOVED VALVES Series W709 AGS Butterfly Valves (175 psi/1270 kpa) 20.07 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION The Series W709 AGS (Advanced Groove System)
More informationMechanical MATERIAL SPECIFICATIONS. Stainless Steel Housing Specifications. Gasket Specifications. Bolt / Nut Specifications
82 COUPLINGS SYSTEM The Grinnell Stainless Steel System is designed for joining 2" to 12" (54,0mm to 206,4mm) stainless steel piping, schedules 5, 10, and 40. The Figure 472 coupling patented Universal
More information0200/11.02 AMTEC. Precision thread inserts for plastic parts and equipment for installation
0200/11.02 AMTEC Precision threa inserts for plastic parts an equipment for installation AMTEC threa inserts Contents Page AMTEC highly wear-resistant threa inserts for plastic parts 3 The avantages an
More informationHigh Pressure Valve Series for Hydrogen Stations
High Pressure Valve Series for Hyrogen Stations Ball Valves Manual Valve Automatic Valve Specifications of Ball Valves KITZ CESTEC -Series Maximum Allowable Pressure 103 MPa: 85 C
More informationSTAINLESS STEEL EXPANSION JOINT, TYPE RFA-S
STAIESS STEEL EXPANSION JOINT, TYPE RFA-S A stainless steel expansion joint with carbon steel flanges for the use in thermal oil pipe systems. For applications where a thermal expansion of the piping has
More informationQuadLube, SpreadLock Seal, ImpactTuff, DuraLube TM Spherical Plain Bearings
QuaLube, SpreaLock Seal, ImpactTuff, uralube TM Spherical Plain earings Innovative prouct features that provie unique performance avantages. High loa capacity, re-lubrication options, an patente esigns.
More informationSeries W706 AGS Butterfly Valves (300 PSI/2065 kpa)
IPS CARBON STEEL PIPE GROOVED VALVES Series W706 AGS Butterfly Valves (300 PSI/2065 kpa) 20.06 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION The Series W706 AGS (Advanced Groove System)
More informationTUBE INSERTS. Your Guide To Finding the right Tube Gauge size: Ribbed Square Inserts
TUBE INSERTS Your Guie To Fining the right Tube Gauge size: Tube Gauge Calculation Metal tubes are available in various tube gauges, although the most commonly use in furniture manufacture range from 10
More informationVariable area flowmeter DFM 165 to 350
ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 D60 Vlotho Fon +9 (0) 57 33.7 990 Fax +9 (0) 57 33.7 99 00 www.asvstuebbe.e contact@asvstuebbe.e Variable area flowmeter DFM to 3 For all inustrial uses High
More informationIndustry. SNR : The Bearing Housings
Inustry SNR : The Bearing ousings Contents Page Bearing ousings n Mounting ccessories 2 ousings 3 Bearings 4 Sealing Systems 6 ubrication 8 Bearing Clearance 10 Mounting Tools 12 Bearing rrangement 13
More informationInstallation, Operation and Maintenance Instructions. Installation, Operating and Maintenance MANUAL. 2 Model 2DDSX04 MK6
Double Disc Pumps Installation, Operating an Maintenance MANUAL 2 Moel 2DDSX04 MK6 PENN VALLEY PUMP Co. Inc. 998 Easton Roa, Warrington, Pa. 18976 (215) 343-8750 Fax (215) 343-8753 www.pennvalleypump.com
More informationModel 7706 Reducing Coupling. Deg. Axial Displacement
MODEL 7706 REDUCING COUPLING The Model 7706 Reducing allows direct reduction on a piping run and eliminates the need for a concentric reducer and couplings. The specially designed rubber gasket prevents
More informationROLLER CHAIN SPROCKETS
ROLLER CHAIN PROCKE ypes an Materials Correct engagement between roller chain an sprocket is require for smooth transmission of roller chain. Appropriate selection of number of teeth (spee ratio), center-to-center
More informationROMAC INDUSTRIES, INC. WIDE RANGE RESTRAINT. RESTRAINED END CAP page 6-7 NOW AVAILABLE FOR HDPE PIPE NO STIFFENER REQUIRED
ROMAC INDUSTRIES, INC. WIDE RANGE RESTRAINT RESTRAINED COUPLING page 4-5 RESTRAINED END CAP page 6-7 RESTRAINED FLANGED COUPLING coming soon JUNE 2014 UPDATE NOW AVAILABLE FOR HDPE PIPE NO STIFFENER REQUIRED
More informationNSK Ball Screws for Standard Stock
NSK Ball s for Stanar Stock ompact Series Next-generation compact ball screws offer quiet, high spee operating performance. stanar stock series assures immeiate elivery. New! Patent Pening BSS Series next-generation
More informationGrooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 48 /1200 in a variety of straight and reducing styles. Most standard fittings are cast of durable
More informationEMCO Corporation Waterworks is not responsible for any errors and discrepencies in the products depicted herein. Information is provided directly
EMCO Corporation Waterworks is not responsible for any errors and discrepencies in the products depicted herein. Information is provided directly from our suppliers. aquamine pvc piping products Victaulic
More informationSection N. 09/2017 Web Revision 10/23/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001: Ford Fabricated Steel Products
DQS Inc. THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Section N 09/2017 Web Revision 10/23/2017 Ford Fabricated Steel Products Contents Page Product Numbering System... 3 Information...............................................................
More informationThe applicable material specifications for ductile iron and rubber gaskets apply:
72 COUPLINGS - Grinnell Copper Grooved System is designed for joining copper tube size components 2" to 8" (54,0mm to 206,4mm) type K, L, M and DWV. All couplings and fittings are rated for working pressures
More informationCapacitance range: 100 pf to 0.22 mf (E12-values on request) Rated voltages:
olypropylene () Capacitors for ulse Applications with Metal oil Electroes, Schoopage Contacts, ouble-sie Metallization an Self-ealing Internal Series Connection for ighest Current Carrying Capability 1
More informationHigh Temperature Masking
Hig Temperature Masking Silicone Caps an Plugs (+300ºC) 92-96 Flexible PVC Caps an Plugs (+220ºC) 97-98 Paper Caps an Plugs (+205ºC) 99 EPM an TPR Caps an Plugs (+180ºC) 100-105 Masking Tapes, Hooks an
More informationP.T.INTERNATIONAL CORP.
» P.T.INTERNATIONAL CORP. Metric & American Inustrial Power Transmission Proucts SR2200 Spherical Roller Bearing Units & Ball Bearing Take Up Frames www.ptintl.com Stock Proucts Metric & American INDUSTRIAL
More information08.20 VIC -300 MasterSeal Butterfly Valves
CRBON STEEL PIPE - GROOVED VLVES Vic -300 MasterSeal butterfly valves are designed for pressures ranging from full vacuum to 300 psi/2065 kpa and for bi-directional, dead end services to full working pressure.
More informationPipe and Flange Protection
Pipe an Flange Protection Pipe Caps 78-82 Pipe Plugs 82-83 Flange Protection 84-89 77 Protect! Pipe an Flange Protection Moss offer a wie range of Plastic Protection Proucts for pipes an flanges. Our range
More information*内輪/B126-B128/E_*内輪/B126-B128/E 11/05/25 10:07 ページ 127 Inner Rings
Inner Rings Inner Rings Inner Rings Inner Rings Many of the neele roller bearings use a shaft as the irect raceway surface without using inner ring. However, it is recommene to use any of the inner rings
More informationNSK Ball Screws for Standard Stock
www.bergab.ru Берг АБ bergab@ya.ru Тел. (495)-228--21, факс (495) 223-371 NSK Ball s for Stanar Stock ompact Series Next-generation compact ball screws offer quiet, high spee operating performance. stanar
More information11.02 Mechanical-T Bolted Branch Outlets
STLES AND SEE ICTAULIC PUBLICATION 10.01 FOR DETAILS NIIPO ictaulic Mechanical-T Outlet provides a direct branch connection at any location a hole can be cut in pipe. The hole is cut oversize to receive
More informationFenner Drives Trantorque Keyless Bushings: Power and Precision
Fenner rives Trantorque Keyless ushings: Power an Precision Fenner rives, a worlwie leaer in mechanical power transmission an motion control solutions, is please to present our comprehensive line of Trantorque
More informationReliable Solutions for Continuous Casters
eliable Solutions for Continuous Casters For More Than A Century, Our Stanars Have Set The Stanar Aroun the worl, companies turn to Timken for innovation an reliability. With expertise in materials science
More informationyour reliable partner EAS -Compact K.490.V16.EN
ES -Compact K.490.V16.EN www..com We safeguar the movements of this worl Specialists for power transmission for more than a century mayr power transmission is one of the most traitional an yet most innovative
More informationSB4 & SB6 SERIES GOLD LINE SIDE-BY-SIDE SHOT PINS
ISO 9001 REGISTERE SB4 & SB6 SERIES GOL LINE SIE-BY-SIE SHOT PINS CORROSION & WEL SPATTER RESISTANT RAM MOUNTING FOR CYLINICATOR STYLE SWITCHES (NOT INCLUE) NAAMS STANAR MOUNTING NPT or G S LIGHTWEIGHT
More informationStyle 233-L & 234-L Rubber Joints
Style 33-L & 3-L Rubber Joints Style 33-L Rubber s are designed for piping systems that experience large lateral offsets due to settlement. The Style 33-L is a low profile triple arch design with a built-in
More informationProduct Submittals for Project
Product Submittals for Project May 011-1 Couplings Figure 577 Light Weight Rigid Coupling For Fire Protection Pressure Rating and Listing / Approval information contact Tyco Fire Suppression & Building
More informationRADIAL AND ANGULAR CONTACT BEARINGS
RIL N NGULR ONTT BERINGS Overview: Timken is a premier manufacturer of ball bearings. We prouce a broa range of precision ball bearings, wie inner ring ball bearings an house units for stanar inustrial
More informationLoop Flushing Valve. Lenntech. Technical Information. Tel Fax
MAKING MODERN LIVING POSSIBLE Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Revision history Table of revisions Date Change Rev Dec 2014 Danfoss Layout EA Oct 2011
More informationWIMA FKP 4. Typical Applications. Construction. Packing. Mechanical Tests
WIMA K 4 olypropylene () Capacitors for ulse Applications with Metal oil Electroes, Schoopage Contacts an Self-ealing, Internal Series Connection for Increase Current Carrying Capability CM 1 mm to 37.
More informationE2EM-X4X1 2M * E2EM-X4X2 2M Shielded E2EM-X8X1 2M * E2EM-X8X2 2M. M30 15 mm E2EM-X15C1 2M E2EM-X15C2 2M. M18 16 mm E2EM-X16MX1 2M E2EM-X16MX2 2M
Long-istance Proximity Sensor EEM CSM_EEM_DS_E_6_ Long-istance Proximity Sensor Long-istance etection at up to mm enables secure mounting with reuce problems ue to workpiece collisions. No polarity for
More informationD I S C C O U P L I N G S
DISC COUPINGS DISC COUPINGS MAIN FEATURES The isc coupling is of the continuous ring laminate metallic iaphragm type with blaes in stainless steel. The torque is transmitte in pure tension through alternate
More informationSCOPE OF WORK WASTEWATER TREATMENT PLANT THE WORLD LEADER IN PIPE JOINING SOLUTIONS
SCOPE OF WORK WASTEWATER TREATMENT PLANT THE WORLD LEADER IN PIPE JOINING SOLUTIONS THE VICTAULIC DIFFERENCE HOUSING GROOVE GASKET BOLT/NUT GROOVE GROOVED PIPE JOINING TECHNOLOGY How does it work? The
More informationIncremental encoders Insulated through hollow shaft ø inch pulses per revolution programmable (interpolated system)
Features HS35P with insulate hollow shaft Robust inustrial encoer up to IP 67 protection Highly versatile fully programmable encoer Interchangeable bore size(s) using metal inserts Insulating sleeve to
More informationCATALOG
CATALOG www.jrbearing.cn www.importbearing.ru 1 The contents of this catalog are subjecte to change without prior notice. Every possible effort has been mae to ensure that the ata herein is correct; however,
More informationSLIM-SPLIT-BEARING KUNSTSTOFF-METALL-FORMTEILE
SLIM-SPLIT-BEARING KUNSTSTOFF-METALL-FORMTEILE Publishe by KMF Kunststoff-Metall-Formteile GmbH Postweg 34-40 -73441 Bopfingen Phone 0736/7001 Fax 0736/7007 E-Mail info@kmf-bearings.e All rights reserve.
More informationk v max 1) [m 3 /h] [mm]
Technical ata sheet D6..N Wafer type butterfly valves, for shut-off functions in open an close col an hot water systems for switching heating an cooling machines on an off Overview of types Type k v max
More information